commit 3e45067f94 upstream.
The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called
with a timeout of 4294968us.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46725b17f1 upstream.
When a uprobe is installed on an instruction that we currently do not
emulate, we copy the instruction into a xol buffer and single step
that instruction. If that instruction generates a fault, we abort the
single stepping before invoking the signal handler. Once the signal
handler is done, the uprobe trap is hit again since the instruction is
retried and the process repeats.
We use uprobe_deny_signal() to detect if the xol instruction triggered
a signal. If so, we clear TIF_SIGPENDING and set TIF_UPROBE so that the
signal is not handled until after the single stepping is aborted. In
this case, uprobe_deny_signal() returns true and get_signal() ends up
returning 0. However, in do_signal(), we are not looking at the return
value, but depending on ksig.sig for further action, all with an
uninitialized ksig that is not touched in this scenario. Fix the same
by initializing ksig.sig to 0.
Fixes: 129b69df9c ("powerpc: Use get_signal() signal_setup_done()")
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05f016d2ca upstream.
As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS
implementation causes a kernel crash. The attached patch corrects the
off by one error in the argument validity check.
In reviewing the code, I noticed that we only perform word operations
with the pointer size argument. The subi instruction intentionally uses
a word condition on 64-bit kernels. Nullification was used instead of a
cmpib instruction as the branch should never be taken. The shlw
pseudo-operation generates a depw,z instruction and it clears the target
before doing a shift left word deposit. Thus, we don't need to clip the
upper 32 bits of this argument on 64-bit kernels.
Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic
code in libgcc is the only direct user of the new CAS implementation
that I am aware of.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a9a17e3bb upstream.
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b8edcc685 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f72271e2a0 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae0c585d93 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e1f9ca546 upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4cb99185b upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52c6912fde upstream.
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c45e3e4c5b upstream.
A recent change fixing NFC device allocation itself introduced an
error-handling bug by returning an error pointer in case device-id
allocation failed. This is clearly broken as the callers still expected
NULL to be returned on errors as detected by Dan's static checker.
Fix this up by returning NULL in the event that we've run out of memory
when allocating a new device id.
Note that the offending commit is marked for stable (3.8) so this fix
needs to be backported along with it.
Fixes: 20777bc57c ("NFC: fix broken device allocation")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1fb354207 upstream.
For the same reason that /proc/iomem returns 0's for non-root readers
and acpi tables are root-only, make the 'resource' attribute for
namespace devices only readable by root. Otherwise we disclose physical
address information.
Fixes: bf9bccc14c ("libnvdimm: pmem label sets and namespace instantiation")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b18d4b8a25 upstream.
The set of valid sequence numbers is {1,2,3}. The specification
indicates that an implementation should consider 0 a sign of a critical
error:
UEFI 2.7: 13.19 NVDIMM Label Protocol
Software never writes the sequence number 00, so a correctly
check-summed Index Block with this sequence number probably indicates a
critical error. When software discovers this case it treats it as an
invalid Index Block indication.
While the expectation is that the invalid block is just thrown away, the
Robustness Principle says we should fix this to make both sequence
numbers valid.
Fixes: f524bf271a ("libnvdimm: write pmem label set")
Reported-by: Juston Li <juston.li@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26417ae4fc upstream.
For the same reason that /proc/iomem returns 0's for non-root readers
and acpi tables are root-only, make the 'resource' attribute for pfn
devices only readable by root. Otherwise we disclose physical address
information.
Fixes: f6ed58c70d ("libnvdimm, pfn: 'resource'-address and 'size'...")
Reported-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33ec6dbc5a upstream.
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Fixes: 660e155193 ("clk: ti: dra7-atl-clock: Fix of_node reference counting")
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15038e1472 upstream.
For many years some users of assigned devices have reported worse
performance on AMD processors with NPT than on AMD without NPT,
Intel or bare metal.
The reason turned out to be that SVM is discarding the guest PAT
setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-,
PA3=UC). The guest might be using a different setting, and
especially might want write combining but isn't getting it
(instead getting slow UC or UC- accesses).
Thanks a lot to geoff@hostfission.com for noticing the relation
to the g_pat setting. The patch has been tested also by a bunch
of people on VFIO users forums.
Fixes: 709ddebf81
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Nick Sarnie <commendsarnex@gmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21f2d55118 upstream.
Intel SDM 27.5.2 Loading Host Segment and Descriptor-Table Registers:
"The GDTR and IDTR limits are each set to FFFFH."
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc3033e16c upstream.
lockd_up() can call lockd_unregister_notifiers twice:
inside lockd_start_svc() when it calls lockd_svc_exit_thread()
and then in error path of lockd_up()
Patch forces lockd_start_svc() to unregister notifiers in all error cases
and removes extra unregister in error path of lockd_up().
Fixes: cb7d224f82 "lockd: unregister notifier blocks if the service ..."
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00ee9a1ca5 upstream.
Fix child-node lookup during initialisation, which ended up searching
the whole device tree depth-first starting at the parent rather than
just matching on its children.
To make things worse, the parent gic node was prematurely freed, while
the ppi-partitions node was leaked.
Fixes: e3825ba1af ("irqchip/gic-v3: Add support for partitioned PPIs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d2fcdcf33 upstream.
For MT2701 NAND Controller, there may generate infinite ECC decode IRQ
during long time burn test on some platforms. Once this issue occurred,
the ECC decode IRQ status cannot be cleared in the IRQ handler function,
and threads cannot be scheduled.
ECC HW generates decode IRQ each sector, so there will have more than one
decode IRQ if read one page of large page NAND.
Currently, ECC IRQ handle flow is that we will check whether it is decode
IRQ at first by reading the register ECC_DECIRQ_STA. This is a read-clear
type register. If this IRQ is decode IRQ, then the ECC IRQ signal will be
cleared at the same time.
Secondly, we will check whether all sectors are decoded by reading the
register ECC_DECDONE. This is because the current IRQ may be not dealed
in time, and the next sectors have been decoded before reading the
register ECC_DECIRQ_STA. Then, the next sectors's decode IRQs will not
be generated.
Thirdly, if all sectors are decoded by comparing with ecc->sectors, then we
will complete ecc->done, set ecc->sectors as 0, and disable ECC IRQ by
programming the register ECC_IRQ_REG(op) as 0. Otherwise, wait for the
next ECC IRQ.
But, there is a timing issue between step one and two. When we read the
reigster ECC_DECIRQ_STA, all sectors are decoded except the last sector,
and the ECC IRQ signal is cleared. But the last sector is decoded before
reading ECC_DECDONE, so the ECC IRQ signal is enabled again by ECC HW, and
it means we will receive one extra ECC IRQ later. In step three, we will
find that all sectors were decoded, then disable ECC IRQ and return.
When deal with the extra ECC IRQ, the ECC IRQ status cannot be cleared
anymore. That is because the register ECC_DECIRQ_STA can only be cleared
when the register ECC_IRQ_REG(op) is enabled. But actually we have
disabled ECC IRQ in the previous ECC IRQ handle. So, there will
keep receiving ECC decode IRQ.
Now, we read the register ECC_DECIRQ_STA once again before completing the
ecc done event. This ensures that there will be no extra ECC decode IRQ.
Also, remove writel(0, ecc->regs + ECC_IRQ_REG(op)) from irq handler,
because ECC IRQ is disabled in mtk_ecc_disable(). And clear ECC_DECIRQ_STA
in mtk_ecc_disable() in case there is a timeout to wait decode IRQ.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30863e38eb upstream.
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c65399 ("mtd: Add panic_write for NAND flashes")
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 739c64414f upstream.
Since v4.12, NAND subpage writes were causing a NULL pointer
dereference on OMAP platforms (omap2-nand) using OMAP_ECC_BCH4_CODE_HW,
OMAP_ECC_BCH8_CODE_HW and OMAP_ECC_BCH16_CODE_HW.
This is because for those ECC modes, omap_calculate_ecc_bch()
generates ECC bytes for the entire (multi-sector) page and this can
overflow the ECC buffer provided by nand_write_subpage_hwecc()
as it expects ecc.calculate() to return ECC bytes for just one sector.
However, the root cause of the problem is present since v3.9
but was not seen then as NAND buffers were being allocated
as one big chunk prior to commit 3deb9979c7 ("mtd: nand: allocate
aligned buffers if NAND_OWN_BUFFERS is unset").
Fix the issue by providing a OMAP optimized write_subpage()
implementation.
Fixes: 62116e5171 ("mtd: nand: omap2: Support for hardware BCH error correction.")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c79df1f34 upstream.
This patch fixes a bug during QUEUE_FULL where transport_complete_qf()
calls transport_complete_task_attr() after it's already been invoked
by target_complete_ok_work() or transport_generic_request_failure()
during initial completion, preceeding QUEUE_FULL.
This will result in se_device->simple_cmds, se_device->dev_cur_ordered_id
and/or se_device->dev_ordered_sync being updated multiple times for
a single se_cmd.
To address this bug, clear SCF_TASK_ATTR_SET after the first call
to transport_complete_task_attr(), and avoid updating SCSI task
attribute related counters for any subsequent calls.
Also, when a se_cmd is deferred due to ordered tags and executed
via target_restart_delayed_cmds(), set CMD_T_SENT before execution
matching what target_execute_cmd() does.
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fc9fb13a4 upstream.
This patch fixes a se_cmd->cmd_kref reference leak that can
occur when a non immediate TMR is proceeded our of command
sequence number order, and CMDSN_LOWER_THAN_EXP is returned
by iscsit_sequence_cmd().
To address this bug, call target_put_sess_cmd() during this
special case following what iscsit_process_scsi_cmd() does
upon CMDSN_LOWER_THAN_EXP.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ee0316315 upstream.
Commit fd2421f544 ("fs/9p: When doing inode lookup compare qid details
and inode mode bits.") transformed v9fs_qid_iget() to use iget5_locked()
instead of iget_locked(). However, the test() callback is not checking
fid.path at all, which means that a lookup in the inode cache can now
accidentally locate a completely wrong inode from the same inode hash
bucket if the other fields (qid.type and qid.version) match.
Fixes: fd2421f544 ("fs/9p: When doing inode lookup compare qid details and inode mode bits.")
Reviewed-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11d49e9d08 upstream.
we are advancing sg as we go, so the pages we need to drop in
case of error are *before* the current sg.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d7fe61857 upstream.
It maybe the typo for ALC700 support patch.
To fix the bit value on this patch.
Fixes: 6fbae35a31 ("ALSA: hda/realtek - Add support for new codecs ALC700/ALC701/ALC703")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2432466f5 upstream.
We got a regression report about the HD-audio HDMI chmap, where some
surround channels are reported as UNKNOWN. The git bisection pointed
the culprit at the commit 9b3dc8aa3f ("ALSA: hda - Register chmap
obj as priv data instead of codec"). The story behind scene is like
this:
- While moving the code out of the legacy HDA to the HDA common place,
the patch modifies the code to obtain the chmap array indirectly in
a byte array, and it expands it to kctl value array.
- At the latter operation, the size of the array is wrongly passed by
sizeof() to the pointer.
- It can be 4 on 32bit arch, thus too short for 6+ channels.
(And that's the reason why it didn't hit other persons; it's 8 on
64bit arch, thus it's usually enough.)
The code was further changed meanwhile, but the problem persisted.
Let's fix it by correctly evaluating the array size.
Fixes: 9b3dc8aa3f ("ALSA: hda - Register chmap obj as priv data instead of codec")
Reported-by: VDR User <user.vdr@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d4e8303f2 upstream.
Some timer compat ioctls have NULL checks of timer instance with
snd_BUG_ON() that bring up WARN_ON() when the debug option is set.
Actually the condition can be met in the normal situation and it's
confusing and bad to spew kernel warnings with stack trace there.
Let's remove snd_BUG_ON() invocation and replace with the simple
checks. Also, correct the error code to EBADFD to follow the native
ioctl error handling.
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a62d6c966 upstream.
The helper functions to parse and look for the clock source, selector
and multiplier unit may return the descriptor with a too short length
than required, while there is no sanity check in the caller side.
Add some sanity checks in the parsers, at least, to guarantee the
given descriptor size, for avoiding the potential crashes.
Fixes: 79f920fbff ("ALSA: usb-audio: parse clock topology of UAC2 devices")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f658f17b5e upstream.
The usb-audio driver may trigger an out-of-bound access at parsing a
malformed selector unit, as it checks the header length only after
evaluating bNrInPins field, which can be already above the given
length. Fix it by adding the length check beforehand.
Fixes: 99fc86450c ("ALSA: usb-mixer: parse descriptors with structs")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d937cd6790 upstream.
When the usb-audio descriptor contains the malformed feature unit
description with a too short length, the driver may access
out-of-bounds. Add a sanity check of the header size at the beginning
of parse_audio_feature_unit().
Fixes: 23caaf19b1 ("ALSA: usb-mixer: Add support for Audio Class v2.0")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e3f985bb upstream.
commit 3179f62001 ("ALSA: core: add .get_time_info") had a side effect
of changing the behaviour of the PCM runtime tstamp. Prior to this
change tstamp was not updated by snd_pcm_update_hw_ptr0() unless the
hw_ptr had moved, after this change tstamp was always updated.
For an application using alsa-lib, doing snd_pcm_readi() followed by
snd_pcm_status() to estimate the age of the read samples by subtracting
status->avail * [sample rate] from status->tstamp this change degraded
the accuracy of the estimate on devices where the pcm hw does not
provide a granular hw_ptr, e.g., devices using
soc-generic-dmaengine-pcm.c and a dma-engine with residue_granularity
DMA_RESIDUE_GRANULARITY_DESCRIPTOR. The accuracy of the estimate
depended on the latency between the PCM hw completing a period and the
driver called snd_pcm_period_elapsed() to notify ALSA core, typically
determined by interrupt handling latency. After the change the accuracy
of the estimate depended on the latency between the PCM hw completing a
period and the application calling snd_pcm_status(), determined by the
scheduling of the application process. The maximum error of the
estimate is one period length in both cases, but the error average and
variance is smaller when it depends on interrupt latency.
Instead of always updating tstamp, update it only if audio_tstamp
changed.
Fixes: 3179f62001 ("ALSA: core: add .get_time_info")
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Henrik Eriksson <henrik.eriksson@axis.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51e3ae81ec upstream.
If there are pending writes subject to delayed allocation, then i_size
will show size after the writes have completed, while i_disksize
contains the value of i_size on the disk (since the writes have not
been persisted to disk).
If fallocate(2) is called with the FALLOC_FL_KEEP_SIZE flag, either
with or without the FALLOC_FL_ZERO_RANGE flag set, and the new size
after the fallocate(2) is between i_size and i_disksize, then after a
crash, if a journal commit has resulted in the changes made by the
fallocate() call to be persisted after a crash, but the delayed
allocation write has not resolved itself, i_size would not be updated,
and this would cause the following e2fsck complaint:
Inode 12, end of extent exceeds allowed value
(logical block 33, physical block 33441, len 7)
This can only take place on a sparse file, where the fallocate(2) call
is allocating blocks in a range which is before a pending delayed
allocation write which is extending i_size. Since this situation is
quite rare, and the window in which the crash must take place is
typically < 30 seconds, in practice this condition will rarely happen.
Nevertheless, it can be triggered in testing, and in particular by
xfstests generic/456.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1601113dd upstream.
When tracing ata link error event, the kernel crashes when the disk is
removed due to NULL pointer access by trace_ata_eh_link_autopsy API.
This occurs as the dev is NULL when the disk disappeared. This patch
fixes this crash by calling trace_ata_eh_link_autopsy only if "dev"
is not NULL.
v2 changes:
Removed direct passing "link" pointer instead of "dev" in trace API.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 255c03d15a ("libata: Add tracepoints")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f2a162fab upstream.
We set rtlhal->last_suspend_sec to an uninitialized stack variable,
but unfortunately gcc never warned about this, I only found it
while working on another patch. I opened a gcc bug for this.
Presumably the value of rtlhal->last_suspend_sec is not all that
important, but it does get used, so we probably want the
patch backported to stable kernels.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 519ce2f933 upstream.
In routine rtl92ee_set_fw_rsvdpagepkt(), the driver allocates an skb, but
never calls rtl_cmd_send_packet(), which will free the buffer. All other
rtlwifi drivers perform this operation correctly.
This problem has been in the driver since it was included in the kernel.
Fortunately, each firmware load only leaks 4 buffers, which likely
explains why it has not previously been detected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95da1b3a5a upstream.
If a delegation has been revoked by the server, operations using that
delegation should error out with NFS4ERR_DELEG_REVOKED in the >4.1
case, and NFS4ERR_BAD_STATEID otherwise.
The server needs NFSv4.1 clients to explicitly free revoked delegations.
If the server returns NFS4ERR_DELEG_REVOKED, the client will do that;
otherwise it may just forget about the delegation and be unable to
recover when it later sees SEQ4_STATUS_RECALLABLE_STATE_REVOKED set on a
SEQUENCE reply. That can cause the Linux 4.1 client to loop in its
stage manager.
Signed-off-by: Andrew Elble <aweits@rit.edu>
Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3944369db7 upstream.
There isn't an obvious way to acquire and release the RCU lock during a
tracepoint, so we can't use the rpc_peeraddr2str() function here.
Instead, rely on the client's cl_hostname, which should have similar
enough information without needing an rcu_dereference().
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c05cefcc72 upstream.
Before traversing a referral and performing a mount, the mounted-on
directory looks strange:
dr-xr-xr-x. 2 4294967294 4294967294 0 Dec 31 1969 dir.0
nfs4_get_referral is wiping out any cached attributes with what was
returned via GETATTR(fs_locations), but the bit mask for that
operation does not request any file attributes.
Retrieve owner and timestamp information so that the memcpy in
nfs4_get_referral fills in more attributes.
Changes since v1:
- Don't request attributes that the client unconditionally replaces
- Request only MOUNTED_ON_FILEID or FILEID attribute, not both
- encode_fs_locations() doesn't use the third bitmask word
Fixes: 6b97fd3da1 ("NFSv4: Follow a referral")
Suggested-by: Pradeep Thomas <pradeepthomas@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34be4dbf87 upstream.
isofs uses a 'char' variable to load the number of years since
1900 for an inode timestamp. On architectures that use a signed
char type by default, this results in an invalid date for
anything beyond 2027.
This changes the function argument to a 'u8' array, which
is defined the same way on all architectures, and unambiguously
lets us use years until 2155.
This should be backported to all kernels that might still be
in use by that date.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91af8300d9 upstream.
In bcache code, sysfs entries are created before all resources get
allocated, e.g. allocation thread of a cache set.
There is posibility for NULL pointer deference if a resource is accessed
but which is not initialized yet. Indeed Jorg Bornschein catches one on
cache set allocation thread and gets a kernel oops.
The reason for this bug is, when bch_bucket_alloc() is called during
cache set registration and attaching, ca->alloc_thread is not properly
allocated and initialized yet, call wake_up_process() on ca->alloc_thread
triggers NULL pointer deference failure. A simple and fast fix is, before
waking up ca->alloc_thread, checking whether it is allocated, and only
wake up ca->alloc_thread when it is not NULL.
Signed-off-by: Coly Li <colyli@suse.de>
Reported-by: Jorg Bornschein <jb@capsec.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b11270853f upstream.
The WARN_ON(!key->len) in set_secret() in net/ceph/crypto.c is hit if a
user tries to add a key of type "ceph" with an invalid payload as
follows (assuming CONFIG_CEPH_LIB=y):
echo -e -n '\x01\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00' \
| keyctl padd ceph desc @s
This can be hit by fuzzers. As this is merely bad input and not a
kernel bug, replace the WARN_ON() with return -EINVAL.
Fixes: 7af3ea189a ("libceph: stop allocating a new cipher on every crypto request")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
