[ Upstream commit c7c06a1532 ]
Family 16h Model 30h SMBus controller needs the same port selection fix
as described and fixed in commit 0fe16195f8 ("i2c: piix4: Fix SMBus port
selection for AMD Family 17h chips")
commit 6befa3fde6 ("i2c: piix4: Support alternative port selection
register") also fixed the port selection for Hudson2, but unfortunately
this is not the exact same device and the AMD naming and PCI Device IDs
aren't particularly helpful here.
The SMBus port selection register is common to the following Families
and models, as documented in AMD's publicly available BIOS and Kernel
Developer Guides:
50742 - Family 15h Model 60h-6Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
55072 - Family 15h Model 70h-7Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
52740 - Family 16h Model 30h-3Fh (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS)
The Hudson2 PCI Device ID (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS) is shared
between Bolton FCH and Family 16h Model 30h, but the location of the
SmBus0Sel port selection bits are different:
51192 - Bolton Register Reference Guide
We distinguish between Bolton and Family 16h Model 30h using the PCI
Revision ID:
Bolton is device 0x780b, revision 0x15
Family 16h Model 30h is device 0x780b, revision 0x1F
Family 15h Model 60h and 70h are both device 0x790b, revision 0x4A.
The following additional public AMD BKDG documents were checked and do
not share the same port selection register:
42301 - Family 15h Model 00h-0Fh doesn't mention any
42300 - Family 15h Model 10h-1Fh doesn't mention any
49125 - Family 15h Model 30h-3Fh doesn't mention any
48751 - Family 16h Model 00h-0Fh uses the previously supported
index register SB800_PIIX4_PORT_IDX_ALT at 0x2e
Signed-off-by: Andrew Cooks <andrew.cooks@opengear.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org [v4.6+]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82e40f558d ]
A guest is not allowed to inject a SGI (or clear its pending state)
by writing to GICD_ISPENDR0 (resp. GICD_ICPENDR0), as these bits are
defined as WI (as per ARM IHI 0048B 4.3.7 and 4.3.8).
Make sure we correctly emulate the architecture.
Fixes: 96b298000d ("KVM: arm/arm64: vgic-new: Add PENDING registers handlers")
Cc: stable@vger.kernel.org # 4.7+
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4a8061a7c ]
If the ap_list is longer than 256 entries, merge_final() in list_sort()
will call the comparison callback with the same element twice, causing
a deadlock in vgic_irq_cmp().
Fix it by returning early when irqa == irqb.
Cc: stable@vger.kernel.org # 4.7+
Fixes: 8e44474579 ("KVM: arm/arm64: vgic-new: Add IRQ sorting")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
[maz: massaged commit log and patch, added Fixes and Cc-stable]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0d31d4dbf3 upstream.
This reverts commit 96cce12ff6 ("cfg80211: fix processing world
regdomain when non modular").
Re-triggering a reg_process_hint with the last request on all events,
can make the regulatory domain fail in case of multiple WiFi modules. On
slower boards (espacially with mdev), enumeration of the WiFi modules
can end up in an intersected regulatory domain, and user cannot set it
with 'iw reg set' anymore.
This is happening, because:
- 1st module enumerates, queues up a regulatory request
- request gets processed by __reg_process_hint_driver():
- checks if previous was set by CORE -> yes
- checks if regulator domain changed -> yes, from '00' to e.g. 'US'
-> sends request to the 'crda'
- 2nd module enumerates, queues up a regulator request (which triggers
the reg_todo() work)
- reg_todo() -> reg_process_pending_hints() sees, that the last request
is not processed yet, so it tries to process it again.
__reg_process_hint driver() will run again, and:
- checks if the last request's initiator was the core -> no, it was
the driver (1st WiFi module)
- checks, if the previous initiator was the driver -> yes
- checks if the regulator domain changed -> yes, it was '00' (set by
core, and crda call did not return yet), and should be changed to 'US'
------> __reg_process_hint_driver calls an intersect
Besides, the reg_process_hint call with the last request is meaningless
since the crda call has a timeout work. If that timeout expires, the
first module's request will lost.
Cc: stable@vger.kernel.org
Fixes: 96cce12ff6 ("cfg80211: fix processing world regdomain when non modular")
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Link: https://lore.kernel.org/r/20190614131600.GA13897@a1-hr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba03a9bbd1 upstream.
Francois reported that VMware balloon gets stuck after a balloon reset,
when the VMCI doorbell is removed. A similar error can occur when the
balloon driver is removed with the following splat:
[ 1088.622000] INFO: task modprobe:3565 blocked for more than 120 seconds.
[ 1088.622035] Tainted: G W 5.2.0 #4
[ 1088.622087] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1088.622205] modprobe D 0 3565 1450 0x00000000
[ 1088.622210] Call Trace:
[ 1088.622246] __schedule+0x2a8/0x690
[ 1088.622248] schedule+0x2d/0x90
[ 1088.622250] schedule_timeout+0x1d3/0x2f0
[ 1088.622252] wait_for_completion+0xba/0x140
[ 1088.622320] ? wake_up_q+0x80/0x80
[ 1088.622370] vmci_resource_remove+0xb9/0xc0 [vmw_vmci]
[ 1088.622373] vmci_doorbell_destroy+0x9e/0xd0 [vmw_vmci]
[ 1088.622379] vmballoon_vmci_cleanup+0x6e/0xf0 [vmw_balloon]
[ 1088.622381] vmballoon_exit+0x18/0xcc8 [vmw_balloon]
[ 1088.622394] __x64_sys_delete_module+0x146/0x280
[ 1088.622408] do_syscall_64+0x5a/0x130
[ 1088.622410] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1088.622415] RIP: 0033:0x7f54f62791b7
[ 1088.622421] Code: Bad RIP value.
[ 1088.622421] RSP: 002b:00007fff2a949008 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 1088.622426] RAX: ffffffffffffffda RBX: 000055dff8b55d00 RCX: 00007f54f62791b7
[ 1088.622426] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 000055dff8b55d68
[ 1088.622427] RBP: 000055dff8b55d00 R08: 00007fff2a947fb1 R09: 0000000000000000
[ 1088.622427] R10: 00007f54f62f5cc0 R11: 0000000000000206 R12: 000055dff8b55d68
[ 1088.622428] R13: 0000000000000001 R14: 000055dff8b55d68 R15: 00007fff2a94a3f0
The cause for the bug is that when the "delayed" doorbell is invoked, it
takes a reference on the doorbell entry and schedules work that is
supposed to run the appropriate code and drop the doorbell entry
reference. The code ignores the fact that if the work is already queued,
it will not be scheduled to run one more time. As a result one of the
references would not be dropped. When the code waits for the reference
to get to zero, during balloon reset or module removal, it gets stuck.
Fix it. Drop the reference if schedule_work() indicates that the work is
already queued.
Note that this bug got more apparent (or apparent at all) due to
commit ce664331b2 ("vmw_balloon: VMCI_DOORBELL_SET does not check status").
Fixes: 83e2ec765b ("VMCI: doorbell implementation.")
Reported-by: Francois Rigault <rigault.francois@gmail.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Adit Ranadive <aditr@vmware.com>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Vishnu DASA <vdasa@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20190820202638.49003-1-namit@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72741084d9 upstream.
The OCR register defines the supported range of VDD voltages for SD cards.
However, it has turned out that some SD cards reports an invalid voltage
range, for example having bit7 set.
When a host supports MMC_CAP2_FULL_PWR_CYCLE and some of the voltages from
the invalid VDD range, this triggers the core to run a power cycle of the
card to try to initialize it at the lowest common supported voltage.
Obviously this fails, since the card can't support it.
Let's fix this problem, by clearing invalid bits from the read OCR register
for SD cards, before proceeding with the VDD voltage negotiation.
Cc: stable@vger.kernel.org
Reported-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Philip Langdale <philipl@overt.org>
Tested-by: Philip Langdale <philipl@overt.org>
Tested-by: Manuel Presnitz <mail@mpy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9212ec7d83 ]
32-bit processes running on a 64-bit kernel are not always detected
correctly, causing the process to crash when uretprobes are installed.
The reason for the crash is that in_ia32_syscall() is used to determine the
process's mode, which only works correctly when called from a syscall.
In the case of uretprobes, however, the function is called from a exception
and always returns 'false' on a 64-bit kernel. In consequence this leads to
corruption of the process's return address.
Fix this by using user_64bit_mode() instead of in_ia32_syscall(), which
is correct in any situation.
[ tglx: Add a comment and the following historical info ]
This should have been detected by the rename which happened in commit
abfb9498ee ("x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()")
which states in the changelog:
The is_ia32_task()/is_x32_task() function names are a big misnomer: they
suggests that the compat-ness of a system call is a task property, which
is not true, the compatness of a system call purely depends on how it
was invoked through the system call layer.
.....
and then it went and blindly renamed every call site.
Sadly enough this was already mentioned here:
8faaed1b9f ("uprobes/x86: Introduce sizeof_long(), cleanup adjust_ret_addr() and
arch_uretprobe_hijack_return_addr()")
where the changelog says:
TODO: is_ia32_task() is not what we actually want, TS_COMPAT does
not necessarily mean 32bit. Fortunately syscall-like insns can't be
probed so it actually works, but it would be better to rename and
use is_ia32_frame().
and goes all the way back to:
0326f5a94d ("uprobes/core: Handle breakpoint and singlestep exceptions")
Oh well. 7+ years until someone actually tried a uretprobe on a 32bit
process on a 64bit kernel....
Fixes: 0326f5a94d ("uprobes/core: Handle breakpoint and singlestep exceptions")
Signed-off-by: Sebastian Mayr <me@sam.st>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190728152617.7308-1-me@sam.st
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a349b95d7c upstream.
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
[ 34.851754] usb 2-1: USB disconnect, device number 2
[ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 35.187886] Workqueue: usb_hub_wq hub_event
[ 35.192063] Call trace:
[ 35.194509] dump_backtrace+0x0/0x150
[ 35.198165] show_stack+0x14/0x20
[ 35.201475] dump_stack+0xa0/0xc4
[ 35.204785] __report_bad_irq+0x34/0xe8
[ 35.208614] note_interrupt+0x2cc/0x318
[ 35.212446] handle_irq_event_percpu+0x5c/0x88
[ 35.216883] handle_irq_event+0x48/0x78
[ 35.220712] handle_fasteoi_irq+0xb4/0x188
[ 35.224802] generic_handle_irq+0x24/0x38
[ 35.228804] __handle_domain_irq+0x5c/0xb0
[ 35.232893] gic_handle_irq+0x58/0xa8
[ 35.236548] el1_irq+0xb8/0x180
[ 35.239681] __do_softirq+0x94/0x23c
[ 35.243253] irq_exit+0xd0/0xd8
[ 35.246387] __handle_domain_irq+0x60/0xb0
[ 35.250475] gic_handle_irq+0x58/0xa8
[ 35.254130] el1_irq+0xb8/0x180
[ 35.257268] kernfs_find_ns+0x5c/0x120
[ 35.261010] kernfs_find_and_get_ns+0x3c/0x60
[ 35.265361] sysfs_unmerge_group+0x20/0x68
[ 35.269454] dpm_sysfs_remove+0x2c/0x68
[ 35.273284] device_del+0x80/0x370
[ 35.276683] hid_destroy_device+0x28/0x60
[ 35.280686] usbhid_disconnect+0x4c/0x80
[ 35.284602] usb_unbind_interface+0x6c/0x268
[ 35.288867] device_release_driver_internal+0xe4/0x1b0
[ 35.293998] device_release_driver+0x14/0x20
[ 35.298261] bus_remove_device+0x110/0x128
[ 35.302350] device_del+0x148/0x370
[ 35.305832] usb_disable_device+0x8c/0x1d0
[ 35.309921] usb_disconnect+0xc8/0x2d0
[ 35.313663] hub_event+0x6e0/0x1128
[ 35.317146] process_one_work+0x1e0/0x320
[ 35.321148] worker_thread+0x40/0x450
[ 35.324805] kthread+0x124/0x128
[ 35.328027] ret_from_fork+0x10/0x18
[ 35.331594] handlers:
[ 35.333862] [<0000000079300c1d>] usb_hcd_irq
[ 35.338126] [<0000000079300c1d>] usb_hcd_irq
[ 35.342389] Disabling IRQ #156
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbe85c88ce upstream.
After _gadget_stop_activity is executed, we can consider the hardware
operation for gadget has finished, and the udc can be stopped and enter
low power mode. So, any later hardware operations (from usb_ep_ops APIs
or usb_gadget_ops APIs) should be considered invalid, any deinitializatons
has been covered at _gadget_stop_activity.
I meet this problem when I plug out usb cable from PC using mass_storage
gadget, my callstack like: vbus interrupt->.vbus_session->
composite_disconnect ->pm_runtime_put_sync(&_gadget->dev),
the composite_disconnect will call fsg_disable, but fsg_disable calls
usb_ep_disable using async way, there are register accesses for
usb_ep_disable. So sometimes, I get system hang due to visit register
without clock, sometimes not.
The Linux Kernel USB maintainer Alan Stern suggests this kinds of solution.
See: http://marc.info/?l=linux-usb&m=138541769810983&w=2.
Cc: <stable@vger.kernel.org> #v4.9+
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20190820020503.27080-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 701d678599 ]
In zs_destroy_pool() we call flush_work(&pool->free_work). However, we
have no guarantee that migration isn't happening in the background at
that time.
Since migration can't directly free pages, it relies on free_work being
scheduled to free the pages. But there's nothing preventing an
in-progress migrate from queuing the work *after*
zs_unregister_migration() has called flush_work(). Which would mean
pages still pointing at the inode when we free it.
Since we know at destroy time all objects should be free, no new
migrations can come in (since zs_page_isolate() fails for fully-free
zspages). This means it is sufficient to track a "# isolated zspages"
count by class, and have the destroy logic ensure all such pages have
drained before proceeding. Keeping that state under the class spinlock
keeps the logic straightforward.
In this case a memory leak could lead to an eventual crash if compaction
hits the leaked page. This crash would only occur if people are
changing their zswap backend at runtime (which eventually starts
destruction).
Link: http://lkml.kernel.org/r/20190809181751.219326-2-henryburns@google.com
Fixes: 48b4800a1c ("zsmalloc: page migration support")
Signed-off-by: Henry Burns <henryburns@google.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Henry Burns <henrywolfeburns@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Jonathan Adams <jwadams@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 558682b529 upstream.
Although APIC initialization will typically clear out the LDR before
setting it, the APIC cleanup code should reset the LDR.
This was discovered with a 32-bit KVM guest jumping into a kdump
kernel. The stale bits in the LDR triggered a bug in the KVM APIC
implementation which caused the destination mapping for VCPUs to be
corrupted.
Note that this isn't intended to paper over the KVM APIC bug. The kernel
has to clear the LDR when resetting the APIC registers except when X2APIC
is enabled.
This lacks a Fixes tag because missing to clear LDR goes way back into pre
git history.
[ tglx: Made x2apic_enabled a function call as required ]
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190826101513.5080-3-bsd@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bae3a8d330 upstream.
Legacy apic init uses bigsmp for smp systems with 8 and more CPUs. The
bigsmp APIC implementation uses physical destination mode, but it
nevertheless initializes LDR and DFR. The LDR even ends up incorrectly with
multiple bit being set.
This does not cause a functional problem because LDR and DFR are ignored
when physical destination mode is active, but it triggered a problem on a
32-bit KVM guest which jumps into a kdump kernel.
The multiple bits set unearthed a bug in the KVM APIC implementation. The
code which creates the logical destination map for VCPUs ignores the
disabled state of the APIC and ends up overwriting an existing valid entry
and as a result, APIC calibration hangs in the guest during kdump
initialization.
Remove the bogus LDR/DFR initialization.
This is not intended to work around the KVM APIC bug. The LDR/DFR
ininitalization is wrong on its own.
The issue goes back into the pre git history. The fixes tag is the commit
in the bitkeeper import which introduced bigsmp support in 2003.
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: db7b9e9f26b8 ("[PATCH] Clustered APIC setup for >8 CPU systems")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190826101513.5080-2-bsd@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75ee23b30d upstream.
Don't advance RIP or inject a single-step #DB if emulation signals a
fault. This logic applies to all state updates that are conditional on
clean retirement of the emulation instruction, e.g. updating RFLAGS was
previously handled by commit 38827dbd3f ("KVM: x86: Do not update
EFLAGS on faulting emulation").
Not advancing RIP is likely a nop, i.e. ctxt->eip isn't updated with
ctxt->_eip until emulation "retires" anyways. Skipping #DB injection
fixes a bug reported by Andy Lutomirski where a #UD on SYSCALL due to
invalid state with EFLAGS.TF=1 would loop indefinitely due to emulation
overwriting the #UD with #DB and thus restarting the bad SYSCALL over
and over.
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@kernel.org>
Fixes: 663f4c61b8 ("KVM: x86: handle singlestep during emulation")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc8d18c75 upstream.
I forgot to release the allocated object at the early error path in
line6_init_pcm(). For addressing it, slightly shuffle the code so
that the PCM destructor (pcm->private_free) is assigned properly
before all error paths.
Fixes: 3450121997 ("ALSA: line6: Fix write on zero-sized buffer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef8d8ccdc2 ]
As Jason Baron explained in commit 790ba4566c ("tcp: set SOCK_NOSPACE
under memory pressure"), it is crucial we properly set SOCK_NOSPACE
when needed.
However, Jason patch had a bug, because the 'nonblocking' status
as far as sk_stream_wait_memory() is concerned is governed
by MSG_DONTWAIT flag passed at sendmsg() time :
long timeo = sock_sndtimeo(sk, flags & MSG_DONTWAIT);
So it is very possible that tcp sendmsg() calls sk_stream_wait_memory(),
and that sk_stream_wait_memory() returns -EAGAIN with SOCK_NOSPACE
cleared, if sk->sk_sndtimeo has been set to a small (but not zero)
value.
This patch removes the 'noblock' variable since we must always
set SOCK_NOSPACE if -EAGAIN is returned.
It also renames the do_nonblock label since we might reach this
code path even if we were in blocking mode.
Fixes: 790ba4566c ("tcp: set SOCK_NOSPACE under memory pressure")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Baron <jbaron@akamai.com>
Reported-by: Vladimir Rutsky <rutsky@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit daac07156b upstream.
The `uac_mixer_unit_descriptor` shown as below is read from the
device side. In `parse_audio_mixer_unit`, `baSourceID` field is
accessed from index 0 to `bNrInPins` - 1, the current implementation
assumes that descriptor is always valid (the length of descriptor
is no shorter than 5 + `bNrInPins`). If a descriptor read from
the device side is invalid, it may trigger out-of-bound memory
access.
```
struct uac_mixer_unit_descriptor {
__u8 bLength;
__u8 bDescriptorType;
__u8 bDescriptorSubtype;
__u8 bUnitID;
__u8 bNrInPins;
__u8 baSourceID[];
}
```
This patch fixes the bug by add a sanity check on the length of
the descriptor.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19bce474c4 upstream.
`check_input_term` recursively calls itself with input from
device side (e.g., uac_input_terminal_descriptor.bCSourceID)
as argument (id). In `check_input_term`, if `check_input_term`
is called with the same `id` argument as the caller, it triggers
endless recursive call, resulting kernel space stack overflow.
This patch fixes the bug by adding a bitmap to `struct mixer_build`
to keep track of the checked ids and stop the execution if some id
has been checked (similar to how parse_audio_unit handles unitid
argument).
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8c3088f895 ("tcp: be more careful in tcp_fragment()")
triggers following stack trace:
[25244.848046] kernel BUG at ./include/linux/skbuff.h:1406!
[25244.859335] RIP: 0010:skb_queue_prev+0x9/0xc
[25244.888167] Call Trace:
[25244.889182] <IRQ>
[25244.890001] tcp_fragment+0x9c/0x2cf
[25244.891295] tcp_write_xmit+0x68f/0x988
[25244.892732] __tcp_push_pending_frames+0x3b/0xa0
[25244.894347] tcp_data_snd_check+0x2a/0xc8
[25244.895775] tcp_rcv_established+0x2a8/0x30d
[25244.897282] tcp_v4_do_rcv+0xb2/0x158
[25244.898666] tcp_v4_rcv+0x692/0x956
[25244.899959] ip_local_deliver_finish+0xeb/0x169
[25244.901547] __netif_receive_skb_core+0x51c/0x582
[25244.903193] ? inet_gro_receive+0x239/0x247
[25244.904756] netif_receive_skb_internal+0xab/0xc6
[25244.906395] napi_gro_receive+0x8a/0xc0
[25244.907760] receive_buf+0x9a1/0x9cd
[25244.909160] ? load_balance+0x17a/0x7b7
[25244.910536] ? vring_unmap_one+0x18/0x61
[25244.911932] ? detach_buf+0x60/0xfa
[25244.913234] virtnet_poll+0x128/0x1e1
[25244.914607] net_rx_action+0x12a/0x2b1
[25244.915953] __do_softirq+0x11c/0x26b
[25244.917269] ? handle_irq_event+0x44/0x56
[25244.918695] irq_exit+0x61/0xa0
[25244.919947] do_IRQ+0x9d/0xbb
[25244.921065] common_interrupt+0x85/0x85
[25244.922479] </IRQ>
tcp_rtx_queue_tail() (called by tcp_fragment()) can call
tcp_write_queue_prev() on the first packet in the queue, which will trigger
the BUG in tcp_write_queue_prev(), because there is no previous packet.
This happens when the retransmit queue is empty, for example in case of a
zero window.
Commit 8c3088f895 ("tcp: be more careful in tcp_fragment()") was not a
simple cherry-pick of the original one from master (b617158dc0)
because there is a specific TCP rtx queue only since v4.15. For more
details, please see the commit message of b617158dc0 ("tcp: be more
careful in tcp_fragment()").
The BUG() is hit due to the specific code added to versions older than
v4.15. The comment in skb_queue_prev() (include/linux/skbuff.h:1406),
just before the BUG_ON() somehow suggests to add a check before using
it, what Tim did.
In master, this code path causing the issue will not be taken because
the implementation of tcp_rtx_queue_tail() is different:
tcp_fragment() → tcp_rtx_queue_tail() → tcp_write_queue_prev() →
skb_queue_prev() → BUG_ON()
Fixes: 8c3088f895 ("tcp: be more careful in tcp_fragment()")
Signed-off-by: Tim Froidcoeur <tim.froidcoeur@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebcb8f8508 ]
Fix RX_TERMINATION_FORCE_ENABLE define value from 0x0089 to 0x00A9
according to MIPI Alliance MPHY specification.
Fixes: e785060ea3 ("ufs: definitions for phy interface")
Signed-off-by: Pedro Sousa <sousa@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae78ca3cf3 ]
In read_per_ring_refs(), after 'req' and related memory regions are
allocated, xen_blkif_map() is invoked to map the shared frame, irq, and
etc. However, if this mapping process fails, no cleanup is performed,
leading to memory leaks. To fix this issue, invoke the cleanup before
returning the error.
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 602fda17c7 ]
In some cases, one can get out of suspend with a reset or
a disconnect followed by a reconnect. Previously we would
leave a stale suspended flag set.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab2cbeb0ed ]
Since scatterlist dimensions are all unsigned ints, in the relatively
rare cases where a device's max_segment_size is set to UINT_MAX, then
the "cur_len + s_length <= max_len" check in __finalise_sg() will always
return true. As a result, the corner case of such a device mapping an
excessively large scatterlist which is mergeable to or beyond a total
length of 4GB can lead to overflow and a bogus truncated dma_length in
the resulting segment.
As we already assume that any single segment must be no longer than
max_len to begin with, this can easily be addressed by reshuffling the
comparison.
Fixes: 809eac54cd ("iommu/dma: Implement scatterlist segment merging")
Reported-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d6fb56072 ]
clang-9 points out that there are two variables that depending on the
configuration may only be used in an ARRAY_SIZE() expression but not
referenced:
drivers/dma/ste_dma40.c:145:12: error: variable 'd40_backup_regs' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs[] = {
^
drivers/dma/ste_dma40.c:214:12: error: variable 'd40_backup_regs_chan' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs_chan[] = {
Mark these __maybe_unused to shut up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190712091357.744515-1-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 9a501cdb05.
Which was upstream commit 53fe307dfd.
Ben Hutchings reports that this commit depends on new code added in
v4.18, and so is irrelevant on older kernels, and breaks the build.
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1fb254aa98 upstream.
Benjamin Moody reported to Debian that XFS partially wedges when a chgrp
fails on account of being out of disk quota. I ran his reproducer
script:
# adduser dummy
# adduser dummy plugdev
# dd if=/dev/zero bs=1M count=100 of=test.img
# mkfs.xfs test.img
# mount -t xfs -o gquota test.img /mnt
# mkdir -p /mnt/dummy
# chown -c dummy /mnt/dummy
# xfs_quota -xc 'limit -g bsoft=100k bhard=100k plugdev' /mnt
(and then as user dummy)
$ dd if=/dev/urandom bs=1M count=50 of=/mnt/dummy/foo
$ chgrp plugdev /mnt/dummy/foo
and saw:
================================================
WARNING: lock held when returning to user space!
5.3.0-rc5 #rc5 Tainted: G W
------------------------------------------------
chgrp/47006 is leaving the kernel with locks still held!
1 lock held by chgrp/47006:
#0: 000000006664ea2d (&xfs_nondir_ilock_class){++++}, at: xfs_ilock+0xd2/0x290 [xfs]
...which is clearly caused by xfs_setattr_nonsize failing to unlock the
ILOCK after the xfs_qm_vop_chown_reserve call fails. Add the missing
unlock.
Reported-by: benjamin.moody@gmail.com
Fixes: 253f4911f2 ("xfs: better xfs_trans_alloc interface")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0ff14fdc9 upstream.
If alloc_descs() fails before irq_sysfs_init() has run, free_desc() in the
cleanup path will call kobject_del() even though the kobject has not been
added with kobject_add().
Fix this by making the call to kobject_del() conditional on whether
irq_sysfs_init() has run.
This problem surfaced because commit aa30f47cf6 ("kobject: Add support
for default attribute groups to kobj_type") makes kobject_del() stricter
about pairing with kobject_add(). If the pairing is incorrrect, a WARNING
and backtrace occur in sysfs_remove_group() because there is no parent.
[ tglx: Add a comment to the code and make it work with CONFIG_SYSFS=n ]
Fixes: ecb3f394c5 ("genirq: Expose interrupt information through sysfs")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1564703564-4116-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cfd5d3399 upstream.
If the sector number is too high, dm_table_find_target() should return a
pointer to a zeroed dm_target structure (the caller should test it with
dm_target_is_valid).
However, for some table sizes, the code in dm_table_find_target() that
performs btree lookup will access out of bound memory structures.
Fix this bug by testing the sector number at the beginning of
dm_table_find_target(). Also, add an "inline" keyword to the function
dm_table_get_size() because this is a hot path.
Fixes: 512875bd96 ("dm: table detect io beyond device")
Cc: stable@vger.kernel.org
Reported-by: Zhang Tao <kontais@zoho.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae148243d3 upstream.
In commit 6096d91af0 ("dm space map metadata: fix occasional leak
of a metadata block on resize"), we refactor the commit logic to a new
function 'apply_bops'. But when that logic was replaced in out() the
return value was not stored. This may lead out() returning a wrong
value to the caller.
Fixes: 6096d91af0 ("dm space map metadata: fix occasional leak of a metadata block on resize")
Cc: stable@vger.kernel.org
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4f9d60138 upstream.
When btree_split_beneath() splits a node to two new children, it will
allocate two blocks: left and right. If right block's allocation
failed, the left block will be unlocked and marked dirty. If this
happened, the left block'ss content is zero, because it wasn't
initialized with the btree struct before the attempot to allocate the
right block. Upon return, when flushing the left block to disk, the
validator will fail when check this block. Then a BUG_ON is raised.
Fix this by completely initializing the left block before allocating and
initializing the right block.
Fixes: 4dcb8b57df ("dm btree: fix leak of bufio-backed block in btree_split_beneath error path")
Cc: stable@vger.kernel.org
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a90118c445 upstream.
Recent gcc compilers (gcc 9.1) generate warnings about an out of bounds
memset, if the memset goes accross several fields of a struct. This
generated a couple of warnings on x86_64 builds in sanitize_boot_params().
Fix this by explicitly saving the fields in struct boot_params
that are intended to be preserved, and zeroing all the rest.
[ tglx: Tagged for stable as it breaks the warning free build there as well ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190731054627.5627-2-jhubbard@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f897e60a12 upstream.
Some newer machines do not advertise legacy timers. The kernel can handle
that situation if the TSC and the CPU frequency are enumerated by CPUID or
MSRs and the CPU supports TSC deadline timer. If the CPU does not support
TSC deadline timer the local APIC timer frequency has to be known as well.
Some Ryzens machines do not advertize legacy timers, but there is no
reliable way to determine the bus frequency which feeds the local APIC
timer when the machine allows overclocking of that frequency.
As there is no legacy timer the local APIC timer calibration crashes due to
a NULL pointer dereference when accessing the not installed global clock
event device.
Switch the calibration loop to a non interrupt based one, which polls
either TSC (if frequency is known) or jiffies. The latter requires a global
clockevent. As the machines which do not have a global clockevent installed
have a known TSC frequency this is a non issue. For older machines where
TSC frequency is not known, there is no known case where the legacy timers
do not exist as that would have been reported long ago.
Reported-by: Daniel Drake <drake@endlessm.com>
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Daniel Drake <drake@endlessm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908091443030.21433@nanos.tec.linutronix.de
Link: http://bugzilla.opensuse.org/show_bug.cgi?id=1142926#c12
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
