The nested_svm_intr() function does not execute the vmexit
anymore. Therefore we may still be in the nested state after
that function ran. This patch changes the nested_svm_intr()
function to return wether the irq window could be enabled.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 8fe546547c)
This patch makes syncing of the guest tpr to the lapic
conditional on !nested. Otherwise a nested guest using the
TPR could freeze the guest.
Another important change this patch introduces is that the
cr8 intercept bits are no longer ORed at vmrun emulation if
the guest sets VINTR_MASKING in its VMCB. The reason is that
nested cr8 accesses need alway be handled by the nested
hypervisor because they change the shadow version of the
tpr.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 88ab24adc7)
The nested_svm_exit_handled_msr() function maps only one
page of the guests msr permission bitmap. This patch changes
the code to use kvm_read_guest to fix the bug.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 4c7da8cb43)
Currently the vmexit emulation does not sync control
registers were the access is typically intercepted by the
nested hypervisor. But we can not count on that intercepts
to sync these registers too and make the code
architecturally more correct.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit cdbbdc1210)
Use of kmap_atomic disables preemption but if we run in
shadow-shadow mode the vmrun emulation executes kvm_set_cr3
which might sleep or fault. So use kmap instead for
nested_svm_map.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
(Cherry-picked from commit 7597f129d8)
commit cf7a50eeb6 upstream.
The control step values reported by the device are used as a divisor
unchecked, which can result in a division by zero.
Check the step value and make it 1 when null.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 0522f6aded upstream.
J.R. Okajima reports that the call to sync_inode() in nfs_wb_page() can
deadlock with other writeback flush calls. It boils down to the fact
that we cannot ever call writeback_single_inode() while holding a page
lock (even if we do set nr_to_write to zero) since another process may
already be waiting in the call to do_writepages(), and so will deny us
the I_SYNC lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c5efa5fc91 upstream.
If we exit from nfs_commit_inode() without ensuring that the COMMIT rpc
call has been completed, we must re-mark the inode as dirty. Otherwise,
future calls to sync_inode() with the WB_SYNC_ALL flag set will fail to
ensure that the data is on the disk.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2f26afba46 upstream.
On btrfs, do the following
------------------
# su user1
# cd btrfs-part/
# touch aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rw-
group::rw-
other::r--
# su user2
# cd btrfs-part/
# setfacl -m u::rwx aaa
# getfacl aaa
# file: aaa
# owner: user1
# group: user1
user::rwx <- successed to setfacl
group::rw-
other::r--
------------------
but we should prohibit it that user2 changing user1's acl.
In fact, on ext3 and other fs, a message occurs:
setfacl: aaa: Operation not permitted
This patch fixed it.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fa588e0c57 upstream.
While creating a file on a server which supports unix extensions
such as Samba, if a file is being created which does not supply
nameidata (i.e. nd is null), cifs client can oops when calling
cifs_posix_open.
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7df0e0397b upstream.
We should be checking for the ownership of the file for which
flags are being set, rather than just for write access.
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1f5a81e41f upstream.
Dan Roseberg has reported a problem with the MOVE_EXT ioctl. If the
donor file is an append-only file, we should not allow the operation
to proceed, lest we end up overwriting the contents of an append-only
file.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 42007efd56 upstream.
If groups_per_flex < 2, sbi->s_flex_groups[] doesn't get filled out,
and every other access to this first tests s_log_groups_per_flex;
same thing needs to happen in resize or we'll wander off into
a null pointer when doing an online resize of the file system.
Thanks to Christoph Biedl, who came up with the trivial testcase:
# truncate --size 128M fsfile
# mkfs.ext3 -F fsfile
# tune2fs -O extents,uninit_bg,dir_index,flex_bg,huge_file,dir_nlink,extra_isize fsfile
# e2fsck -yDf -C0 fsfile
# truncate --size 132M fsfile
# losetup /dev/loop0 fsfile
# mount /dev/loop0 mnt
# resize2fs -p /dev/loop0
https://bugzilla.kernel.org/show_bug.cgi?id=13549
Reported-by: Alessandro Polverini <alex@nibbles.it>
Test-case-by: Christoph Biedl <bugzilla.kernel.bpeb@manchmal.in-ulm.de>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ac9721f3f5 upstream.
In order to move toward separate buffer objects, rework the whole
perf_mmap_data construct to be a more self-sufficient entity, one
with its own lifetime rules.
This greatly sanitizes the whole output redirection code, which
was riddled with bugs and races.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b160fdabe9 upstream.
The conversion of write_inode_now calls to commit_metadata in commit
f501912a35 missed out the call in nfsd_setattr.
But without this conversion we can't guarantee that a SETATTR request
has actually been commited to disk with XFS, which causes a regression
from 2.6.32 (only for NFSv2, but anyway).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f6ab91add6 upstream.
Frederic reported that frequency driven swevents didn't work properly
and even caused a division-by-zero error.
It turns out there are two bugs, the division-by-zero comes from a
failure to deal with that in perf_calculate_period().
The other was more interesting and turned out to be a wrong comparison
in perf_adjust_period(). The comparison was between an s64 and u64 and
got implicitly converted to an unsigned comparison. The problem is
that period_left is typically < 0, so it ended up being always true.
Cure this by making the local period variables s64.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 3d79b2a9ee upstream.
We currently have this check as a BUG_ON, which is being hit by people.
Previously it was an error with a recalculation if not current, return that
code.
The BUG_ON was introduced by:
commit 3110bef78c
Author: Guy Cohen <guy.cohen@intel.com>
Date: Tue Sep 9 10:54:54 2008 +0800
iwlwifi: Added support for 3 antennas
... the portion adding the BUG_ON is reverted since we are encountering the error
and BUG_ON was created with assumption that error is not encountered.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 073d5eab6f upstream.
It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.
Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
there is some locking missing around the "is_internal_short_scan"
variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
scan and thus causes problems with wrong memory being accessed.
The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c043f12456 upstream.
This patch (as1387) fixes a bug introduced during the changeover to
the runtime PM framework. When a driver doesn't support resume or
reset-resume, and consequently its interfaces need to be unbound and
rebound, we have to unbind all the interfaces before trying to rebind
any of them. Otherwise the driver's probe method for one interface
could try to claim a different interface and fail, because that other
interface hasn't been unbound yet.
This fixes Bugzilla #15788. The symptom is that some USB sound cards
don't work after hibernation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: François Valenduc <francois.valenduc@tvcablenet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c2572b78aa upstream.
This patch fixes resource reclaim in error path of acm_probe:
1. In the case of "out of memory (read urbs usb_alloc_urb)\n")", there
is no need to call acm_read_buffers_free(acm) here. Fix it by goto
alloc_fail6 instead of alloc_fail7.
2. In the case of "out of memory (write urbs usb_alloc_urb)",
usb_alloc_urb may fail in any iteration of the for loop. Current
implementation does not properly free allocated snd->urb. Fix it by
goto alloc_fail8 instead of alloc_fail7.
3. In the case of device_create_file(&intf->dev,&dev_attr_iCountryCodeRelDate)
fail, acm->country_codes is kfreed. As a result, device_remove_file
for dev_attr_wCountryCodes will not be executed in acm_disconnect.
Fix it by calling device_remove_file for dev_attr_wCountryCodes
before goto skip_countries.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6a1a82df91 upstream.
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 2d62f3eea9 upstream.
After software resets an xHCI host controller, it must wait for the
"Controller Not Ready" (CNR) bit in the status register to be cleared.
Software is not supposed to ring any doorbells or write to any registers
except the status register until this bit is cleared.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ed07453fd3 upstream.
When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Shinya Saito <shinya.saito.sx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 9908ff736a upstream.
We can, by virtue of a vblank interrupt firing in the middle of setting
up the unpin work (i.e. after we set the unpin_work field and before we
write to the ringbuffer) enter intel_finish_page_flip() prior to
receiving the pending flip notification. Therefore we can expect to hit
intel_finish_page_flip() under normal circumstances without a pending flip
and even without installing the pending_flip_obj. This is exacerbated by
aperture thrashing whilst binding the framebuffer
References:
Bug 28079 - "glresize" causes kernel panic in intel_finish_page_flip.
https://bugs.freedesktop.org/show_bug.cgi?id=28079
Reported-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 8b27ff4cf6 upstream.
vt6421 has problems talking to recent WD drives. It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.
https://bugzilla.kernel.org/show_bug.cgi?id=15173
Joseph Chan provided the following fix. I don't have any idea what it
does but I can verify the issue is gone with the patch applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw>
Reported-by: Jorrit Tijben <sjorrit@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f3faf8fc3f upstream.
On mcp55, nIEN gets stuck once set and liteon blueray rom iHOS104-08
violates ATA specification and fails to set I on D2H Reg FIS if nIEN
is set when the command was issued. When the other party is following
the spec, both devices can work fine but when the two flaws are put
together, they can't talk to each other.
mcp55 has its own IRQ masking mechanism and there's no reason to mess
with nIEN in the first place. Fix it by dropping nIEN diddling from
nv_mcp55_freeze/thaw().
This was originally reported by Cengiz. Although Cengiz hasn't
verified the fix yet, I could reproduce this problem and verfiy the
fix. Even if Cengiz is experiencing different or additional problems,
this patch is needed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Cengiz Günay <cgunay@emory.edu>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 94b3dd0f7b upstream.
Child groups should have a greater depth than their parents. Prior to
this change, the parent would incorrectly report zero memory usage for
child cgroups when use_hierarchy is enabled.
test script:
mount -t cgroup none /cgroups -o memory
cd /cgroups
mkdir cg1
echo 1 > cg1/memory.use_hierarchy
mkdir cg1/cg11
echo $$ > cg1/cg11/tasks
dd if=/dev/zero of=/tmp/foo bs=1M count=1
echo
echo CHILD
grep cache cg1/cg11/memory.stat
echo
echo PARENT
grep cache cg1/memory.stat
echo $$ > tasks
rmdir cg1/cg11 cg1
cd /
umount /cgroups
Using fae9c79, a recent patch that changed alloc_css_id() depth computation,
the parent incorrectly reports zero usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out
1048576 bytes (1.0 MB) copied, 0.0151844 s, 69.1 MB/s
CHILD
cache 1048576
total_cache 1048576
PARENT
cache 0
total_cache 0
With this patch, the parent correctly includes child usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out
1048576 bytes (1.0 MB) copied, 0.0136827 s, 76.6 MB/s
CHILD
cache 1052672
total_cache 1052672
PARENT
cache 0
total_cache 1052672
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 79907d89c3 upstream.
10, 233 is allocated officially to /dev/kmview which is shipping in
Ubuntu and Debian distributions. vhost_net seem to have borrowed it
without making a proper request and this causes regressions in the other
distributions.
vhost_net can use a dynamic minor so use that instead. Also update the
file with a comment to try and avoid future misunderstandings.
Signed-off-by: Alan Cox <device@lanana.org>
[ We should have caught this before 2.6.34 got released. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1038953674 upstream.
Per IEEE 1394 clause 8.4.2.3, a contender for the IRM role shall check
whether the current IRM complies to 1394a-2000 or later. If not force a
compliant node (e.g. itself) to become IRM. This was implemented in the
older ieee1394 driver but not yet in firewire-core.
An older Sony camcorder (Sony DCR-TRV25) which implements 1394-1995 IRM
but neither 1394a-2000 IRM nor BM was now found to cause an
interoperability bug:
- Camcorder becomes root node when plugged in, hence gets IRM role.
- firewire-core successfully contends for BM role, proceeds to perform
gap count optimization and resets the bus.
- Sony camcorder ignores presence of a BM (against the spec, this is
a firmware bug), performs its idea of gap count optimization and
resets the bus.
- Preceding two steps are repeated endlessly, bus never settles,
regular I/O is practically impossible.
http://thread.gmane.org/gmane.linux.kernel.firewire.user/3913
This is an interoperability regression from the old to the new drivers.
Fix it indirectly by adding the 1394a IRM check. The spec suggests
three and a half methods to determine 1394a compliance of a remote IRM;
we choose the method of testing the Config_ROM.Bus_Info.generation
field. This is data that firewire-core should have readily available at
this point, i.e. does not require extra I/O.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (missing 1394a check)
Reported-by: H. S. <hs.samix@gmail.com> (issue with Sony DCR-TRV25)
Tested-by: H. S. <hs.samix@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 4daedcfe8c upstream.
JMB362 is a new variant of jmicron controller which is similar to
JMB360 but has two SATA ports instead of one. As there is no PATA
port, single function AHCI mode can be used as in JMB360. Add pci
quirk for JMB362.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 6b5dcccb49 upstream.
Commit 56d1de0a21, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b054b747a6 upstream.
When we receive a deauthentication frame before
having successfully associated, we neither print
a message nor abort assocation. The former makes
it hard to debug, while the latter later causes
a warning in cfg80211 when, as will typically be
the case, association timed out.
This warning was reported by many, e.g. in
https://bugzilla.kernel.org/show_bug.cgi?id=15981,
but I couldn't initially pinpoint it. I verified
the fix by hacking hostapd to send a deauth frame
instead of an association response.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit b83156b52d upstream.
Commit a8408c17 introduced a new check to pccard_validate_cis(),
which avoids any "late" calls to this function. This broke the
insertion of cards which require a CIS override which changes
the number of card functions. Fix this by asserting that this
is _not_ a late call, but a proper call early during the card
insertion process.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=16138
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 84fe6c19e4 upstream.
Add a spin_unlock missing on the error path. The locks and unlocks are
balanced in other functions, so it seems that the same should be the case
here.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* spin_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* spin_unlock(E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit cbab05f041 upstream.
Making gconfig fails on fedora 13 as the linker cannot resolve dlsym.
Adding libdl to the link command fixes this.
make shows this error :-
/usr/bin/ld: scripts/kconfig/kconfig_load.o: undefined reference to symbol 'dlsym@@GLIBC_2.2.5'
/usr/bin/ld: note: 'dlsym@@GLIBC_2.2.5' is defined in DSO /lib64/libdl.so.2 so try adding it to the linker command line
/lib64/libdl.so.2: could not read symbols: Invalid operation
tested on x86_64 fedora 13.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit f4d7c3565c upstream.
Based on the sh_tmu change in 66f49121ff
("clocksource: sh_tmu: compute mult and shift before registration").
The same issues impact the sh_cmt driver, so we take the same approach
here.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 66f49121ff upstream.
Since commit 98962465ed ("nohz: Prevent
clocksource wrapping during idle"), the CPU of an R2D board never goes
to idle. This commit assumes that mult and shift are assigned before
the clocksource is registered. As a consequence the safe maximum sleep
time is negative and the CPU never goes into idle.
This patch fixes the problem by moving mult and shift initialization
from sh_tmu_clocksource_enable() to sh_tmu_register_clocksource().
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit ebe8622342 upstream.
Correct at least one of the incorrect specs for a national instrument
data acquisition card DAQCard-6024E. This card has only four different
gain settings (+-10V, +-5V, +-0.5V, +-0.05V).
Signed-off-by: Martin Homuth-Rosemann <homuth-rosemann@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 55adaa495e upstream.
Limit number of accumulated non-balloonable pages during inflation cycle,
otherwise there is a chance we will be spinning and growing the list
forever. This happens during torture tests when balloon target changes
while we are in the middle of inflation cycle and monitor starts refusing
to lock pages (since they are not needed anymore).
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Acked-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
