commit ecfb9f4047 upstream.
The previous algorithm was pretty broken.
- The inner loop had a '(m > m_max)' condition, and the value of 'm'
would increase in each iteration;
- Each iteration would actually multiply 'm' by two, so it is not needed
to re-compute the whole equation at each iteration;
- It would loop until (m & 1) == 0, which means it would loop at most
once.
- The outer loop would divide the 'n' value by two at the end of each
iteration. This meant that for a 12 MHz parent clock and a 1.2 GHz
requested clock, it would first try n=12, then n=6, then n=3, then
n=1, none of which would work; the only valid value is n=2 in this
case.
Simplify this algorithm with a single for loop, which decrements 'n'
after each iteration, addressing all of the above problems.
Fixes: bdbfc02937 ("clk: ingenic: Add support for the JZ4760")
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20221214123704.7305-1-paul@crapouillou.net
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54e5c00a4e upstream.
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
Fixes: c1e5c2f0cb ("usb: typec: altmodes/displayport: correct pin assignment for UFP receptacles")
Cc: stable@vger.kernel.org
Reported-by: Diana Zigterman <dzigterman@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20230208205318.131385-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f58d783fd upstream.
We have this check to make sure we don't accidentally add older devices
that may have disappeared and re-appeared with an older generation from
being added to an fs_devices (such as a replace source device). This
makes sense, we don't want stale disks in our file system. However for
single disks this doesn't really make sense.
I've seen this in testing, but I was provided a reproducer from a
project that builds btrfs images on loopback devices. The loopback
device gets cached with the new generation, and then if it is re-used to
generate a new file system we'll fail to mount it because the new fs is
"older" than what we have in cache.
Fix this by freeing the cache when closing the device for a single device
filesystem. This will ensure that the mount command passed device path is
scanned successfully during the next mount.
CC: stable@vger.kernel.org # 5.10+
Reported-by: Daan De Meyer <daandemeyer@fb.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1249db44a1 upstream.
Currently the subflow error report callback unconditionally
propagates the fallback subflow status to the owning msk.
If the msk is already orphaned, the above prevents the code
from correctly tracking the msk moving to the TCP_CLOSE state
and doing the appropriate cleanup.
All the above causes increasing memory usage over time and
sporadic self-tests failures.
There is a great deal of infrastructure trying to propagate
correctly the fallback subflow status to the owning mptcp socket,
e.g. via mptcp_subflow_eof() and subflow_sched_work_if_closed():
in the error propagation path we need only to cope with unorphaned
sockets.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/339
Fixes: 15cc104533 ("mptcp: deliver ssk errors to msk")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa5465aeca upstream.
When the network status is unstable, use-after-free may occur when
read data from the server.
BUG: KASAN: use-after-free in readpages_fill_pages+0x14c/0x7e0
Call Trace:
<TASK>
dump_stack_lvl+0x38/0x4c
print_report+0x16f/0x4a6
kasan_report+0xb7/0x130
readpages_fill_pages+0x14c/0x7e0
cifs_readv_receive+0x46d/0xa40
cifs_demultiplex_thread+0x121c/0x1490
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
</TASK>
Allocated by task 2535:
kasan_save_stack+0x22/0x50
kasan_set_track+0x25/0x30
__kasan_kmalloc+0x82/0x90
cifs_readdata_direct_alloc+0x2c/0x110
cifs_readdata_alloc+0x2d/0x60
cifs_readahead+0x393/0xfe0
read_pages+0x12f/0x470
page_cache_ra_unbounded+0x1b1/0x240
filemap_get_pages+0x1c8/0x9a0
filemap_read+0x1c0/0x540
cifs_strict_readv+0x21b/0x240
vfs_read+0x395/0x4b0
ksys_read+0xb8/0x150
do_syscall_64+0x3f/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
Freed by task 79:
kasan_save_stack+0x22/0x50
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2e/0x50
__kasan_slab_free+0x10e/0x1a0
__kmem_cache_free+0x7a/0x1a0
cifs_readdata_release+0x49/0x60
process_one_work+0x46c/0x760
worker_thread+0x2a4/0x6f0
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
Last potentially related work creation:
kasan_save_stack+0x22/0x50
__kasan_record_aux_stack+0x95/0xb0
insert_work+0x2b/0x130
__queue_work+0x1fe/0x660
queue_work_on+0x4b/0x60
smb2_readv_callback+0x396/0x800
cifs_abort_connection+0x474/0x6a0
cifs_reconnect+0x5cb/0xa50
cifs_readv_from_socket.cold+0x22/0x6c
cifs_read_page_from_socket+0xc1/0x100
readpages_fill_pages.cold+0x2f/0x46
cifs_readv_receive+0x46d/0xa40
cifs_demultiplex_thread+0x121c/0x1490
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
The following function calls will cause UAF of the rdata pointer.
readpages_fill_pages
cifs_read_page_from_socket
cifs_readv_from_socket
cifs_reconnect
__cifs_reconnect
cifs_abort_connection
mid->callback() --> smb2_readv_callback
queue_work(&rdata->work) # if the worker completes first,
# the rdata is freed
cifs_readv_complete
kref_put
cifs_readdata_release
kfree(rdata)
return rdata->... # UAF in readpages_fill_pages()
Similarly, this problem also occurs in the uncache_fill_pages().
Fix this by adjusts the order of condition judgment in the return
statement.
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Cc: stable@vger.kernel.org
Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c63b8fd14a ]
Due to using the u16 type in the min_t() macros the SPI transfer length
will be cast to word before participating in the conditional statement
implied by the macro. Thus if the transfer length is greater than 64KB the
Tx/Rx FIFO threshold level value will be determined by the leftover of the
truncated after the type-case length. In the worst case it will cause the
dramatical performance drop due to the "Tx FIFO Empty" or "Rx FIFO Full"
interrupts triggered on each xfer word sent/received to/from the bus.
The problem can be easily fixed by specifying the unsigned int type in the
min_t() macros thus preventing the possible data loss.
Fixes: ea11370fff ("spi: dw: get TX level without an additional variable")
Reported-by: Sergey Nazarov <Sergey.Nazarov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230113185942.2516-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb80242cc6 ]
When running kfence_test, I found some testcases failed like this:
# test_out_of_bounds_read: EXPECTATION FAILED at mm/kfence/kfence_test.c:346
Expected report_matches(&expect) to be true, but is false
not ok 1 - test_out_of_bounds_read
The corresponding call-trace is:
BUG: KFENCE: out-of-bounds read in kunit_try_run_case+0x38/0x84
Out-of-bounds read at 0x(____ptrval____) (32B right of kfence-#10):
kunit_try_run_case+0x38/0x84
kunit_generic_run_threadfn_adapter+0x12/0x1e
kthread+0xc8/0xde
ret_from_exception+0x0/0xc
The kfence_test using the first frame of call trace to check whether the
testcase is succeed or not. Commit 6a00ef4493 ("riscv: eliminate
unreliable __builtin_frame_address(1)") skip first frame for all
case, which results the kfence_test failed. Indeed, we only need to skip
the first frame for case (task==NULL || task==current).
With this patch, the call-trace will be:
BUG: KFENCE: out-of-bounds read in test_out_of_bounds_read+0x88/0x19e
Out-of-bounds read at 0x(____ptrval____) (1B left of kfence-#7):
test_out_of_bounds_read+0x88/0x19e
kunit_try_run_case+0x38/0x84
kunit_generic_run_threadfn_adapter+0x12/0x1e
kthread+0xc8/0xde
ret_from_exception+0x0/0xc
Fixes: 6a00ef4493 ("riscv: eliminate unreliable __builtin_frame_address(1)")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Tested-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221207025038.1022045-1-liushixin2@huawei.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dac9f8dc2 ]
This loop accidentally reuses the "i" iterator for both the inside and
the outside loop. The value of MAX_STREAM_BUFFER is 5. I believe that
chip->rmh.stat_len is in the 2-12 range. If the value of .stat_len is
4 or more then it will loop exactly one time, but if it's less then it
is a forever loop.
It looks like it was supposed to combined into one loop where
conditions are checked.
Fixes: 8e6320064c ("ALSA: lx_core: Remove useless #if 0 .. #endif")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y9jnJTis/mRFJAQp@kili
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b27517627 ]
On some platforms, 100/1000/2500 speeds seem to have sometimes problems
reporting false positive tx unit hang during stressful UDP traffic. Likely
other Intel drivers introduce responses to a tx hang. Update the 'tx hang'
comparator with the comparison of the head and tail of ring pointers and
restore the tx_timeout_factor to the previous value (one).
This can be test by using netperf or iperf3 applications.
Example:
iperf3 -s -p 5001
iperf3 -c 192.168.0.2 --udp -p 5001 --time 600 -b 0
netserver -p 16604
netperf -H 192.168.0.2 -l 600 -p 16604 -t UDP_STREAM -- -m 64000
Fixes: b27b8dc77b ("igc: Increase timeout value for Speed 100/1000/2500")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230206235818.662384-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f0d1451ec ]
Currently, remove and reload flows can run in parallel to module cleanup.
This design is error prone. For example: aux_drivers callbacks are called
from both cleanup and remove flows with different lockings, which can
cause a deadlock[1].
Hence, serialize module cleanup with reload and remove.
[1]
cleanup remove
------- ------
auxiliary_driver_unregister();
devl_lock()
auxiliary_device_delete(mlx5e_aux)
device_lock(mlx5e_aux)
devl_lock()
device_lock(mlx5e_aux)
Fixes: 912cebf420 ("net/mlx5e: Connect ethernet part to auxiliary bus")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 184e1e4474 ]
When tracer is reloaded, the device will log the traces at the
beginning of the log buffer. Also, driver is reading the log buffer in
chunks in accordance to the consumer index.
Hence, zero consumer index when reloading the tracer.
Fixes: 4383cfcc65 ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db561fed6b ]
Whenever the driver is reading the string DBs into buffers, the driver
is setting the load bit, but the driver never clears this bit.
As a result, in case load bit is on and the driver query the device for
new string DBs, the driver won't read again the string DBs.
Fix it by clearing the load bit when query the device for new string
DBs.
Fixes: 2d69356752 ("net/mlx5: Add support for fw live patch event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa5f171d5 ]
ethtool is returning an error for unknown speeds for the IPoIB interface:
$ ethtool ib0
netlink error: failed to retrieve link settings
netlink error: Invalid argument
netlink error: failed to retrieve link settings
netlink error: Invalid argument
Settings for ib0:
Link detected: no
After this change, ethtool will return success and show "unknown speed":
$ ethtool ib0
Settings for ib0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: no
Fixes: eb234ee9d5 ("net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da0c52426c ]
SWITCHDEV_FDB_ADD_TO_BRIDGE event handler that updates FDB entry 'lastuse'
field is only executed for eswitch that owns the entry. However, if peer
entry processed packets at least once it will have hardware counter 'used'
value greater than entry 'lastuse' from that point on, which will cause FDB
entry not being aged out.
Process the event on all eswitch instances.
Fixes: ff9b752146 ("net/mlx5: Bridge, support LAG")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e66220948 ]
rq->hw_mtu is used in function en_rx.c/mlx5e_skb_from_cqe_mpwrq_linear()
to catch oversized packets. If FCS is concatenated to the end of the
packet then the check should be updated accordingly.
Rx rings initialization (mlx5e_init_rxq_rq()) invoked for every new set
of channels, as part of mlx5e_safe_switch_params(), unknowingly if it
runs with default configuration or not. Current rq->hw_mtu
initialization assumes default configuration and ignores
params->scatter_fcs_en flag state.
Fix this, by accounting for params->scatter_fcs_en flag state during
rq->hw_mtu initialization.
In addition, updating rq->hw_mtu value during ingress traffic might
lead to packets drop and oversize_pkts_sw_drop counter increase with no
good reason. Hence we remove this optimization and switch the set of
channels with a new one, to make sure we don't get false positives on
the oversize_pkts_sw_drop counter.
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Adham Faris <afaris@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9ba64deb2 ]
Add a function to flush an RQ: clean up descriptors, release pages and
reset the RQ. This procedure is used by the recovery flow, and it will
also be used in a following commit to free some memory when switching a
channel to the XSK mode.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 1e66220948 ("net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e64d71d055 ]
The same clear_bit is called in both error and success flows. Move the
call to do it only once and remove the out label.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 1e66220948 ("net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f964f8399d ]
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
With a command such as the following:
tc filter add dev $swp1 ingress chain $(IS1 2) pref 3 \
protocol 802.1Q flower skip_sw vlan_id 200 src_mac $h1_mac \
action vlan modify id 300 \
action goto chain $(IS2 0 0)
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e610 ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de11 ("net: mscc: ocelot: support matching on EtherType")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b6d642510 ]
Frank reports that in a mt7530 setup where some ports are standalone and
some are in a VLAN-aware bridge, 8021q uppers of the standalone ports
lose their VLAN tag on xmit, as seen by the link partner.
This seems to occur because once the other ports join the VLAN-aware
bridge, mt7530_port_vlan_filtering() also calls
mt7530_port_set_vlan_aware(ds, cpu_dp->index), and this affects the way
that the switch processes the traffic of the standalone port.
Relevant is the PVC_EG_TAG bit. The MT7530 documentation says about it:
EG_TAG: Incoming Port Egress Tag VLAN Attribution
0: disabled (system default)
1: consistent (keep the original ingress tag attribute)
My interpretation is that this setting applies on the ingress port, and
"disabled" is basically the normal behavior, where the egress tag format
of the packet (tagged or untagged) is decided by the VLAN table
(MT7530_VLAN_EGRESS_UNTAG or MT7530_VLAN_EGRESS_TAG).
But there is also an option of overriding the system default behavior,
and for the egress tagging format of packets to be decided not by the
VLAN table, but simply by copying the ingress tag format (if ingress was
tagged, egress is tagged; if ingress was untagged, egress is untagged;
aka "consistent). This is useful in 2 scenarios:
- VLAN-unaware bridge ports will always encounter a miss in the VLAN
table. They should forward a packet as-is, though. So we use
"consistent" there. See commit e045124e93 ("net: dsa: mt7530: fix
tagged frames pass-through in VLAN-unaware mode").
- Traffic injected from the CPU port. The operating system is in god
mode; if it wants a packet to exit as VLAN-tagged, it sends it as
VLAN-tagged. Otherwise it sends it as VLAN-untagged*.
*This is true only if we don't consider the bridge TX forwarding offload
feature, which mt7530 doesn't support.
So for now, make the CPU port always stay in "consistent" mode to allow
software VLANs to be forwarded to their egress ports with the VLAN tag
intact, and not stripped.
Link: https://lore.kernel.org/netdev/trinity-e6294d28-636c-4c40-bb8b-b523521b00be-1674233135062@3c-app-gmx-bs36/
Fixes: e045124e93 ("net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230205140713.1609281-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03702d4d29 ]
Since commit 58e0be1ef6 ("net: use struct_group to copy ip/ipv6
header addresses"), ip and ipv6 headers started to use the __struct_group
definition, which is defined at include/uapi/linux/stddef.h. However,
linux/stddef.h isn't explicitly included in include/uapi/linux/{ip,ipv6}.h,
which breaks build of xskxceiver bpf selftest if you install the uapi
headers in the system:
$ make V=1 xskxceiver -C tools/testing/selftests/bpf
...
make: Entering directory '(...)/tools/testing/selftests/bpf'
gcc -g -O0 -rdynamic -Wall -Werror (...)
In file included from xskxceiver.c:79:
/usr/include/linux/ip.h:103:9: error: expected specifier-qualifier-list before ‘__struct_group’
103 | __struct_group(/* no tag */, addrs, /* no attrs */,
| ^~~~~~~~~~~~~~
...
Include the missing <linux/stddef.h> dependency in ip.h and do the
same for the ipv6.h header.
Fixes: 58e0be1ef6 ("net: use struct_group to copy ip/ipv6 header addresses")
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Reviewed-by: Carlos O'Donell <carlos@redhat.com>
Tested-by: Carlos O'Donell <carlos@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8797a0584 ]
Clear the interrupt credits before enabling the queue rather
than after to be sure that the enabled queue starts at 0 and
that we don't wipe away possible credits after enabling the
queue.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Neel Patel <neel.patel@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce93fdb5f2 ]
After calling fwnode_phy_find_device(), the phy device refcount is
incremented. Then, when the phy device is attached to a netdev with
phy_attach_direct(), the refcount is also incremented but only
decremented in the caller if phy_attach_direct() fails. Move
phy_device_free() before the "if" to always release it correctly.
Indeed, either phy_attach_direct() failed and we don't want to keep a
reference to the phydev or it succeeded and a reference has been taken
internally.
Fixes: 25396f680d ("net: phylink: introduce phylink_fwnode_phy_connect()")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6028da3f12 ]
When copying the DSCP bits for decap-dscp into IPv6 don't assume the
outer encap is always IPv6. Instead, as with the inner IPv4 case, copy
the DSCP bits from the correctly saved "tos" value in the control block.
Fixes: 227620e295 ("[IPSEC]: Separate inner/outer mode processing on input")
Signed-off-by: Christian Hopps <chopps@chopps.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6ee896385 ]
int type = nla_type(nla);
if (type > XFRMA_MAX) {
return -EOPNOTSUPP;
}
@type is then used as an array index and can be used
as a Spectre v1 gadget.
if (nla_len(nla) < compat_policy[type].len) {
array_index_nospec() can be used to prevent leaking
content of kernel memory to malicious users.
Fixes: 5106f4a8ac ("xfrm/compat: Add 32=>64-bit messages translator")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dmitry Safonov <dima@arista.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4ae5e1e97c upstream.
The ISO 11783-5 standard, in "4.5.2 - Address claim requirements", states:
d) No CF shall begin, or resume, transmission on the network until 250
ms after it has successfully claimed an address except when
responding to a request for address-claimed.
But "Figure 6" and "Figure 7" in "4.5.4.2 - Address-claim
prioritization" show that the CF begins the transmission after 250 ms
from the first AC (address-claimed) message even if it sends another AC
message during that time window to resolve the address contention with
another CF.
As stated in "4.4.2.3 - Address-claimed message":
In order to successfully claim an address, the CF sending an address
claimed message shall not receive a contending claim from another CF
for at least 250 ms.
As stated in "4.4.3.2 - NAME management (NM) message":
1) A commanding CF can
d) request that a CF with a specified NAME transmit the address-
claimed message with its current NAME.
2) A target CF shall
d) send an address-claimed message in response to a request for a
matching NAME
Taking the above arguments into account, the 250 ms wait is requested
only during network initialization.
Do not restart the timer on AC message if both the NAME and the address
match and so if the address has already been claimed (timer has expired)
or the AC message has been sent to resolve the contention with another
CF (timer is still running).
Signed-off-by: Devid Antonio Filoni <devid.filoni@egluetechnologies.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20221125170418.34575-1-devid.filoni@egluetechnologies.com
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6933c01e4 upstream.
Commit 7a8b64d17e ("of/address: use range parser for of_dma_get_range")
converted the parsing of dma-range properties to use code shared with the
PCI range parser. The intent was to introduce no functional changes however
in the case where we fail to translate the first resource instead of
returning -EINVAL the new code we return 0. Restore the previous behaviour
by returning an error if we find no valid ranges, the original code only
handled the first range but subsequently support for parsing all supplied
ranges was added.
This avoids confusing code using the parsed ranges which doesn't expect to
successfully parse ranges but have only a list terminator returned, this
fixes breakage with so far as I can tell all DMA for on SoC devices on the
Socionext Synquacer platform which has a firmware supplied DT. A bisect
identified the original conversion as triggering the issues there.
Fixes: 7a8b64d17e ("of/address: use range parser for of_dma_get_range")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Luca Di Stefano <luca.distefano@linaro.org>
Cc: 993612@bugs.debian.org
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20230126-synquacer-boot-v2-1-cb80fd23c4e2@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e46d910d8 upstream.
poll() and select() on per_cpu trace_pipe and trace_pipe_raw do not work
since kernel 6.1-rc6. This issue is seen after the commit
42fb0a1e84 ("tracing/ring-buffer: Have
polling block on watermark").
This issue is firstly detected and reported, when testing the CXL error
events in the rasdaemon and also erified using the test application for poll()
and select().
This issue occurs for the per_cpu case, when calling the ring_buffer_poll_wait(),
in kernel/trace/ring_buffer.c, with the buffer_percent > 0 and then wait until the
percentage of pages are available. The default value set for the buffer_percent is 50
in the kernel/trace/trace.c.
As a fix, allow userspace application could set buffer_percent as 0 through
the buffer_percent_fops, so that the task will wake up as soon as data is added
to any of the specific cpu buffer.
Link: https://lore.kernel.org/linux-trace-kernel/20230202182309.742-2-shiju.jose@huawei.com
Cc: <mhiramat@kernel.org>
Cc: <mchehab@kernel.org>
Cc: <linux-edac@vger.kernel.org>
Cc: stable@vger.kernel.org
Fixes: 42fb0a1e84 ("tracing/ring-buffer: Have polling block on watermark")
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
