[ Upstream commit eed6e57e9f3e2beac37563eb6a0129549daa330e ]
Commit c14e64b469 ("soc: qcom: llcc: Support chipsets that can
write to llcc") add the support for chipset where capacity based
allocation and retention through power collapse can be programmed
based on content of SCT table mentioned in the llcc driver where
the target like sdm845 where the entire programming related to it
is controlled in firmware. However, the commit introduces a bug
where capacity/retention register get overwritten each time it
gets programmed for each slice and that results in misconfiguration
of the register based on SCT table and that is not expected
behaviour instead it should be read modify write to retain the
configuration of other slices.
This issue is totally caught from code review and programming test
and not through any power/perf numbers so, it is not known what
impact this could make if we don't have this change however,
this feature are for these targets and they should have been
programmed accordingly as per their configuration mentioned in
SCT table like others bits information.
This change brings one difference where it keeps capacity/retention
bits of the slices that are not mentioned in SCT table in unknown
state where as earlier it was initialized to zero.
Fixes: c14e64b469 ("soc: qcom: llcc: Support chipsets that can write to llcc")
Signed-off-by: Atul Dhudase <quic_adhudase@quicinc.com>
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1701876771-10695-1-git-send-email-quic_mojha@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b07bc2347672cc8c7293c64499f1488278c5ca3d ]
Reproduced with below sequence:
dma_declare_coherent_memory()->dma_release_coherent_memory()
->dma_declare_coherent_memory()->"return -EBUSY" error
It will return -EBUSY from the dma_assign_coherent_memory()
in dma_declare_coherent_memory(), the reason is that dev->dma_mem
pointer has not been set to NULL after it's freed.
Fixes: cf65a0f6f6 ("dma-mapping: move all DMA mapping code to kernel/dma")
Signed-off-by: Joakim Zhang <joakim.zhang@cixtech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93b80887668226180ea5f5349cc728ca6dc700ab ]
Add one more condition for sending credit update during dequeue from
stream socket: when number of bytes in the rx queue is smaller than
SO_RCVLOWAT value of the socket. This is actual for non-default value
of SO_RCVLOWAT (e.g. not 1) - idea is to "kick" peer to continue data
transmission, because we need at least SO_RCVLOWAT bytes in our rx
queue to wake up user for reading data (in corner case it is also
possible to stuck both tx and rx sides, this is why 'Fixes' is used).
Fixes: b89d882dc9 ("vsock/virtio: reduce credit update messages")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb7403655b3c3eb245d0ee330047cd3e20b3c4af ]
In order to support IP_PKTINFO on those packets, we need to call
ipv4_pktinfo_prepare.
When sending mrouted/pimd daemons a cache report IGMP msg, it is
unnecessary to set dst on the newly created skb.
It used to be necessary on older versions until
commit d826eb14ec ("ipv4: PKTINFO doesnt need dst reference") which
changed the way IP_PKTINFO struct is been retrieved.
Changes from v1:
1. Undo changes in ipv4_pktinfo_prepare function. use it directly
and copy the control block.
Fixes: d826eb14ec ("ipv4: PKTINFO doesnt need dst reference")
Signed-off-by: Leone Fernando <leone4fernando@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a33e9da3470499e9ff476138f271fb52d6bfe767 ]
When running fib_nexthop_multiprefix test I saw all IPv6 test failed.
e.g.
]# ./fib_nexthop_multiprefix.sh
TEST: IPv4: host 0 to host 1, mtu 1300 [ OK ]
TEST: IPv6: host 0 to host 1, mtu 1300 [FAIL]
With -v it shows
COMMAND: ip netns exec h0 /usr/sbin/ping6 -s 1350 -c5 -w5 2001:db8:101::1
PING 2001:db8:101::1(2001:db8:101::1) 1350 data bytes
From 2001:db8:100::64 icmp_seq=1 Packet too big: mtu=1300
--- 2001:db8:101::1 ping statistics ---
1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms
Route get
2001:db8:101::1 via 2001:db8:100::64 dev eth0 src 2001:db8:100::1 metric 1024 expires 599sec mtu 1300 pref medium
Searching for:
2001:db8:101::1 from :: via 2001:db8:100::64 dev eth0 src 2001:db8:100::1 .* mtu 1300
The reason is when CONFIG_IPV6_SUBTREES is not enabled, rt6_fill_node() will
not put RTA_SRC info. After fix:
]# ./fib_nexthop_multiprefix.sh
TEST: IPv4: host 0 to host 1, mtu 1300 [ OK ]
TEST: IPv6: host 0 to host 1, mtu 1300 [ OK ]
Fixes: 735ab2f65d ("selftests: Add test with multiple prefixes using single nexthop")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20231213060856.4030084-7-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc3c6743de0ecb169026c36cbdbc0d12d22a528 ]
The binding erroneously decreed that the SCMI variants of the ST
evaluation kits are compatible with the non-SCMI variants.
This is not correct, as a kernel or bootloader compatible with the non-SCMI
variant is not necessarily able to function, when direct access
to resources is replaced by having to talk SCMI to the secure monitor.
The binding has been adjusted to reflect thus, so synchronize the device
trees now.
Fixes: 5b7e58313a ("ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ea3e7763c50b20a8bd25cf524ea0c6463de69be ]
We obtain the semaphore and set HISI_SAS_RESETTING_BIT in
hisi_sas_reset_prepare_v3_hw(), block the scsi host and set
HISI_SAS_REJECT_CMD_BIT in hisi_sas_controller_reset_prepare(), released
them in hisi_sas_controller_reset_done(). However, if the HW reset failure
in FLR results in early return, the semaphore and flag bits will not be
release.
Rollback some operations including clearing flags / releasing semaphore
when FLR is failed.
Fixes: e5ea48014a ("scsi: hisi_sas: Implement handlers of PCIe FLR for v3 hw")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-5-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d34ee535705eb43885bc0f561c63046f697355ad ]
In function hisi_sas_controller_prereset(), -ENOSYS (Function not
implemented) should be returned if the driver does not support .soft_reset.
Returns -EPERM (Operation not permitted) if HISI_SAS_RESETTING_BIT is
already be set.
In function _suspend_v3_hw(), returns -EPERM (Operation not permitted) if
HISI_SAS_RESETTING_BIT is already be set.
Fixes: 4522204ab2 ("scsi: hisi_sas: tidy host controller reset function a bit")
Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1702525516-51258-3-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f794d3eed5345413c2b0cf1bcccc92d77681220 ]
When the GPU nodes were added, the GPU_PLL_OUT was configured
for 1000MHz, but this requires the SoC to run in overdrive mode
which requires an elevated voltage operating point.
Since this may run some boards out of spec, the default clock
should be set to 800MHz for nominal operating mode. Boards
that run at the higher voltage can update their clocks
accordingly.
Fixes: 4523be8e46 ("arm64: dts: imx8mm: Add GPU nodes for 2D and 3D core")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fa3d1a00c2d4ba14f1300371ad39d5456e890d7 ]
On the error path of device_add_disk(), device's memalloc_noio flag was
set but not cleared. As the comment of pm_runtime_set_memalloc_noio(),
"The function should be called between device_add() and device_del()".
Clear this flag before device_del() now.
Fixes: 25e823c8c3 ("block/genhd.c: apply pm_runtime_set_memalloc_noio on block devices")
Signed-off-by: Li Nan <linan122@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20231211075356.1839282-1-linan666@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa6ad88e023ddfa6c5dcdb466d159e89f451e305 ]
Due to the increase in the number of power tables for 6Ghz on CLC,
the variable nr_country is no longer sufficient to represent the
total quantity. Therefore, we have switched to calculating the
length of clc buf to obtain the correct power table. Additionally,
the version number has been incremented to 1.
Fixes: 23bdc5d8ca ("wifi: mt76: mt7921: introduce Country Location Control support")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5f185bf7c42f6ca885202fefc40fc871d08a722 ]
The DMA-related nodes RDMA/WROT in MDP3 should be changed to generic names.
In addition, fix improper space indent in example.
Fixes: 4ad7b39623 ("media: dt-binding: mediatek: add bindings for MediaTek MDP3 components")
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44ab3ee76a5a977864ba0bb6c352dcf6206804e0 ]
The Hi6421 PMIC regulator child nodes do not have unit addresses so drop
the incorrect '#address-cells' and '#size-cells' properties.
Fixes: 6219b20e1e ("arm64: dts: hisilicon: Add support for Hikey 970 PMIC")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a833a17aeac73b33f79433d7cee68d5cafd71e4f ]
This patch fixes a bug around the verification of possibly-zero-sized
stack accesses. When the access was done through a var-offset stack
pointer, check_stack_access_within_bounds was incorrectly computing the
maximum-offset of a zero-sized read to be the same as the register's min
offset. Instead, we have to take in account the register's maximum
possible value. The patch also simplifies how the max offset is checked;
the check is now simpler than for min offset.
The bug was allowing accesses to erroneously pass the
check_stack_access_within_bounds() checks, only to later crash in
check_stack_range_initialized() when all the possibly-affected stack
slots are iterated (this time with a correct max offset).
check_stack_range_initialized() is relying on
check_stack_access_within_bounds() for its accesses to the
stack-tracking vector to be within bounds; in the case of zero-sized
accesses, we were essentially only verifying that the lowest possible
slot was within bounds. We would crash when the max-offset of the stack
pointer was >= 0 (which shouldn't pass verification, and hopefully is
not something anyone's code attempts to do in practice).
Thanks Hao for reporting!
Fixes: 01f810ace9 ("bpf: Allow variable-offset stack access")
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Andrei Matei <andreimatei1@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20231207041150.229139-2-andreimatei1@gmail.com
Closes: https://lore.kernel.org/bpf/CACkBjsZGEUaRCHsmaX=h-efVogsRfK1FPxmkgb0Os_frnHiNdw@mail.gmail.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92184eae1d5ad804884e2c6e289d885b9e3194d1 ]
The ieee80211_queue_work function queues work into the mac80211
local->workqueue, which is widely used for mac80211 internal
work processes. In the mt76 driver, both the mt76-sido-status and
mt76-sdio-net threads enqueue workers to the workqueue with this
function. However, in some cases, when two workers are enqueued
to the workqueue almost simultaneously, the second worker may not
be scheduled immediately and may get stuck for a while.
This can cause timing issues. To avoid these timing
conflicts caused by worker scheduling, replace the worker
with an independent thread.
Fixes: 48fab5bbef ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24f8aba9a7c77c7e9d814a5754798e8346c7dd28 ]
The DP/DM wakeup interrupts are edge triggered and which edge to trigger
on depends on use-case and whether a Low speed or Full/High speed device
is connected.
Note that only triggering on rising edges can be used to detect resume
events but not disconnect events.
Fixes: bb9efa59c6 ("arm64: dts: qcom: sc7280: Add USB related nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231120164331.8116-6-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94085049fdad7a36fe14dd55e72e712fe55d6bca ]
GPU_SMMU SID 1 is meant for Adreno LPAC (Low Priority Async Compute).
On platforms that support it (in firmware), it is necessary to
describe that link, or Adreno register access will hang the board.
The current settings are functionally identical, *but* due to what is
likely hardcoded security policies, the secure firmware rejects them,
resulting in the board hanging. To avoid that, alter the settings such
that SID 0 and 1 are described separately.
Fixes: 96c471970b ("arm64: dts: qcom: sc7280: Add gpu support")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230926-topic-a643-v2-2-06fa3d899c0a@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab125ed3ec1c10ccc36bc98c7a4256ad114a3dae ]
When register is spilled onto a stack as a 1/2/4-byte register, we set
slot_type[BPF_REG_SIZE - 1] (plus potentially few more below it,
depending on actual spill size). So to check if some stack slot has
spilled register we need to consult slot_type[7], not slot_type[0].
To avoid the need to remember and double-check this in the future, just
use is_spilled_reg() helper.
Fixes: 27113c59b6 ("bpf: Check the other end of slot_type for STACK_SPILL")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231205184248.1502704-4-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f770d28f2e5abfd442ad689ba1129dd66593529 ]
When do arping, the interface need to be specified. Or we will
get error: Interface "lo" is not ARPable. And the test failed.
]# ./arp_ndisc_untracked_subnets.sh
TEST: test_arp: accept_arp=0 [ OK ]
TEST: test_arp: accept_arp=1 [FAIL]
TEST: test_arp: accept_arp=2 same_subnet=0 [ OK ]
TEST: test_arp: accept_arp=2 same_subnet=1 [FAIL]
After fix:
]# ./arp_ndisc_untracked_subnets.sh
TEST: test_arp: accept_arp=0 [ OK ]
TEST: test_arp: accept_arp=1 [ OK ]
TEST: test_arp: accept_arp=2 same_subnet=0 [ OK ]
TEST: test_arp: accept_arp=2 same_subnet=1 [ OK ]
Fixes: 0ea7b0a454 ("selftests: net: arp_ndisc_untracked_subnets: test for arp_accept and accept_untracked_na")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 876673364161da50eed6b472d746ef88242b2368 ]
When updating or deleting an inner map in map array or map htab, the map
may still be accessed by non-sleepable program or sleepable program.
However bpf_map_fd_put_ptr() decreases the ref-counter of the inner map
directly through bpf_map_put(), if the ref-counter is the last one
(which is true for most cases), the inner map will be freed by
ops->map_free() in a kworker. But for now, most .map_free() callbacks
don't use synchronize_rcu() or its variants to wait for the elapse of a
RCU grace period, so after the invocation of ops->map_free completes,
the bpf program which is accessing the inner map may incur
use-after-free problem.
Fix the free of inner map by invoking bpf_map_free_deferred() after both
one RCU grace period and one tasks trace RCU grace period if the inner
map has been removed from the outer map before. The deferment is
accomplished by using call_rcu() or call_rcu_tasks_trace() when
releasing the last ref-counter of bpf map. The newly-added rcu_head
field in bpf_map shares the same storage space with work field to
reduce the size of bpf_map.
Fixes: bba1dc0b55 ("bpf: Remove redundant synchronize_rcu.")
Fixes: 638e4b825d ("bpf: Allows per-cpu maps and map-in-map in sleepable programs")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20231204140425.1480317-5-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20c20bd11a0702ce4dc9300c3da58acf551d9725 ]
map is the pointer of outer map, and need_defer needs some explanation.
need_defer tells the implementation to defer the reference release of
the passed element and ensure that the element is still alive before
the bpf program, which may manipulate it, exits.
The following three cases will invoke map_fd_put_ptr() and different
need_defer values will be passed to these callers:
1) release the reference of the old element in the map during map update
or map deletion. The release must be deferred, otherwise the bpf
program may incur use-after-free problem, so need_defer needs to be
true.
2) release the reference of the to-be-added element in the error path of
map update. The to-be-added element is not visible to any bpf
program, so it is OK to pass false for need_defer parameter.
3) release the references of all elements in the map during map release.
Any bpf program which has access to the map must have been exited and
released, so need_defer=false will be OK.
These two parameters will be used by the following patches to fix the
potential use-after-free problem for map-in-map.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20231204140425.1480317-3-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 876673364161 ("bpf: Defer the free of inner map when necessary")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2595473046 ]
Add a generic percpu stats for bpf_map elements insertions/deletions in order
to keep track of both, the current (approximate) number of elements in a map
and per-cpu statistics on update/delete operations.
To expose these stats a particular map implementation should initialize the
counter and adjust it as needed using the 'bpf_map_*_elem_count' helpers
provided by this commit.
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Link: https://lore.kernel.org/r/20230706133932.45883-2-aspsk@isovalent.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 876673364161 ("bpf: Defer the free of inner map when necessary")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6c86c513f ]
As an accident of implementation, an RCU Tasks Trace grace period also
acts as an RCU grace period. However, this could change at any time.
This commit therefore creates an rcu_trace_implies_rcu_gp() that currently
returns true to codify this accident. Code relying on this accident
must call this function to verify that this accident is still happening.
Reported-by: Hou Tao <houtao@huaweicloud.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Martin KaFai Lau <martin.lau@linux.dev>
Link: https://lore.kernel.org/r/20221014113946.965131-2-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 876673364161 ("bpf: Defer the free of inner map when necessary")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6da24ba932082bae110feb917a64bb54637fa7c0 ]
With the standard Qualcomm TrustZone setup, components such as lpasscc,
pdc_reset and watchdog shouldn't be touched by Linux. Mark them with
the status 'reserved' and reenable them in the chrome-common dtsi.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20230919-fp5-initial-v2-1-14bb7cedadf5@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stable-dep-of: 6897fac411db ("arm64: dts: qcom: sc7280: Make watchdog bark interrupt edge triggered")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ac90b4cf107a3999b30844d7899e0331686b33b ]
On sc7180 when the watchdog timer fires your logs get filled with:
watchdog0: pretimeout event
watchdog0: pretimeout event
watchdog0: pretimeout event
...
watchdog0: pretimeout event
If you're using console-ramoops to debug crashes the above gets quite
annoying since it blows away any other log messages that might have
been there.
The issue is that the "bark" interrupt (AKA the "pretimeout"
interrupt) remains high until the watchdog is pet. Since we've got
things configured as "level" triggered we'll keep getting interrupted
over and over.
Let's switch to edge triggered. Now we'll get one interrupt when the
"bark" interrupt goes off and won't get another one until the "bark"
interrupt is cleared and asserts again.
This matches how many older Qualcomm SoCs have things configured.
Fixes: 28cc13e406 ("arm64: dts: qcom: sc7180: Add watchdog bark interrupt")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20231106144335.v2.1.Ic7577567baff921347d423b722de8b857602efb1@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0acd03a5bd188b0c501d285d938439618bd855c4 ]
Given verifier checks actual value, r0 has to be precise, so we need to
propagate precision properly. r0 also has to be marked as read,
otherwise subsequent state comparisons will ignore such register as
unimportant and precision won't really help here.
Fixes: 69c087ba62 ("bpf: Add bpf_for_each_map_elem() helper")
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231202175705.885270-4-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa2bbff7b0b4e211fec5e5686ef96350690597b5 ]
Currently rcu is used to protect iterating rdev from submit_flushes():
submit_flushes remove_and_add_spares
synchronize_rcu
pers->hot_remove_disk()
rcu_read_lock()
rdev_for_each_rcu
if (rdev->raid_disk >= 0)
rdev->radi_disk = -1;
atomic_inc(&rdev->nr_pending)
rcu_read_unlock()
bi = bio_alloc_bioset()
bi->bi_end_io = md_end_flush
bi->private = rdev
submit_bio
// issue io for removed rdev
Fix this problem by grabbing 'acive_io' before iterating rdev, make sure
that remove_and_add_spares() won't concurrent with submit_flushes().
Fixes: a2826aa92e ("md: support barrier requests on all personalities.")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20231129020234.1586910-1-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b57160859263c083c49482b0d083a586b1517f78 ]
DSS irq trigger type is set to IRQ_TYPE_EDGE_RISING in the DT file, but
the TRM says it is level triggered.
For some reason triggering on rising edge results in double the amount
of expected interrupts, e.g. for normal page flipping test the number of
interrupts per second is 2 * fps. It is as if the IRQ triggers on both
edges. There are no other side effects to this issue than slightly
increased CPU & power consumption due to the extra interrupt.
Switching to IRQ_TYPE_LEVEL_HIGH is correct and fixes the issue, so
let's do that.
Fixes: fc539b90ed ("arm64: dts: ti: am654: Add DSS node")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20231106-am65-dss-clk-edge-v1-1-4a959fec0e1e@ideasonboard.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e45f243409 ]
In some meson boards, secure monitor device has children, for example,
power secure controller. By default, secure monitor isn't the bus in terms
of device tree subsystem, so the of_platform initialization code doesn't
populate its device tree data. As a result, secure monitor's children
aren't probed at all.
Run the 'of_platform_populate()' routine manually to resolve such issues.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230324145557.27797-1-ddrokosov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Stable-dep-of: d8385d7433f9 ("firmware: meson-sm: unmap out_base shmem in error path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3084b58bfd0b9e4b5e034f31f31b42977db35f12 ]
The netlink interface for major and minor version numbers doesn't actually
return the major and minor version numbers.
It reports a u32 that contains the (major, minor, update, alpha1)
components as the major version number, and then alpha2 as the minor
version number.
For whatever reason, the u32 byte order was reversed (ntohl): maybe it was
assumed that the encoded value was a single big-endian u32, and alpha2 was
the minor version.
The correct way to get the supported NC-SI version from the network
controller is to parse the Get Version ID response as described in 8.4.44
of the NC-SI spec[1].
Get Version ID Response Packet Format
Bits
+--------+--------+--------+--------+
Bytes | 31..24 | 23..16 | 15..8 | 7..0 |
+-------+--------+--------+--------+--------+
| 0..15 | NC-SI Header |
+-------+--------+--------+--------+--------+
| 16..19| Response code | Reason code |
+-------+--------+--------+--------+--------+
|20..23 | Major | Minor | Update | Alpha1 |
+-------+--------+--------+--------+--------+
|24..27 | reserved | Alpha2 |
+-------+--------+--------+--------+--------+
| .... other stuff .... |
The major, minor, and update fields are all binary-coded decimal (BCD)
encoded [2]. The spec provides examples below the Get Version ID response
format in section 8.4.44.1, but for practical purposes, this is an example
from a live network card:
root@bmc:~# ncsi-util 0x15
NC-SI Command Response:
cmd: GET_VERSION_ID(0x15)
Response: COMMAND_COMPLETED(0x0000) Reason: NO_ERROR(0x0000)
Payload length = 40
20: 0xf1 0xf1 0xf0 0x00 <<<<<<<<< (major, minor, update, alpha1)
24: 0x00 0x00 0x00 0x00 <<<<<<<<< (_, _, _, alpha2)
28: 0x6d 0x6c 0x78 0x30
32: 0x2e 0x31 0x00 0x00
36: 0x00 0x00 0x00 0x00
40: 0x16 0x1d 0x07 0xd2
44: 0x10 0x1d 0x15 0xb3
48: 0x00 0x17 0x15 0xb3
52: 0x00 0x00 0x81 0x19
This should be parsed as "1.1.0".
"f" in the upper-nibble means to ignore it, contributing zero.
If both nibbles are "f", I think the whole field is supposed to be ignored.
Major and minor are "required", meaning they're not supposed to be "ff",
but the update field is "optional" so I think it can be ff. I think the
simplest thing to do is just set the major and minor to zero instead of
juggling some conditional logic or something.
bcd2bin() from "include/linux/bcd.h" seems to assume both nibbles are 0-9,
so I've provided a custom BCD decoding function.
Alpha1 and alpha2 are ISO/IEC 8859-1 encoded, which just means ASCII
characters as far as I can tell, although the full encoding table for
non-alphabetic characters is slightly different (I think).
I imagine the alpha fields are just supposed to be alphabetic characters,
but I haven't seen any network cards actually report a non-zero value for
either.
If people wrote software against this netlink behavior, and were parsing
the major and minor versions themselves from the u32, then this would
definitely break their code.
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0222_1.0.0.pdf
[2] https://en.wikipedia.org/wiki/Binary-coded_decimal
[2] https://en.wikipedia.org/wiki/ISO/IEC_8859-1
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Fixes: 138635cc27 ("net/ncsi: NCSI response packet handler")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
