commit 8c462d56487e3abdbf8a61cedfe7c795a54f4a78 upstream.
SMCCCv1.3 added a hint bit which callers can set in an SMCCC function ID
(AKA "FID") to indicate that it is acceptable for the SMCCC
implementation to discard SVE and/or SME state over a specific SMCCC
call. The kernel support for using this hint is broken and SMCCC calls
may clobber the SVE and/or SME state of arbitrary tasks, though FPSIMD
state is unaffected.
The kernel support is intended to use the hint when there is no SVE or
SME state to save, and to do this it checks whether TIF_FOREIGN_FPSTATE
is set or TIF_SVE is clear in assembly code:
| ldr <flags>, [<current_task>, #TSK_TI_FLAGS]
| tbnz <flags>, #TIF_FOREIGN_FPSTATE, 1f // Any live FP state?
| tbnz <flags>, #TIF_SVE, 2f // Does that state include SVE?
|
| 1: orr <fid>, <fid>, ARM_SMCCC_1_3_SVE_HINT
| 2:
| << SMCCC call using FID >>
This is not safe as-is:
(1) SMCCC calls can be made in a preemptible context and preemption can
result in TIF_FOREIGN_FPSTATE being set or cleared at arbitrary
points in time. Thus checking for TIF_FOREIGN_FPSTATE provides no
guarantee.
(2) TIF_FOREIGN_FPSTATE only indicates that the live FP/SVE/SME state in
the CPU does not belong to the current task, and does not indicate
that clobbering this state is acceptable.
When the live CPU state is clobbered it is necessary to update
fpsimd_last_state.st to ensure that a subsequent context switch will
reload FP/SVE/SME state from memory rather than consuming the
clobbered state. This and the SMCCC call itself must happen in a
critical section with preemption disabled to avoid races.
(3) Live SVE/SME state can exist with TIF_SVE clear (e.g. with only
TIF_SME set), and checking TIF_SVE alone is insufficient.
Remove the broken support for the SMCCCv1.3 SVE saving hint. This is
effectively a revert of commits:
* cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
* a7c3acca53 ("arm64: smccc: Save lr before calling __arm_smccc_sve_check()")
... leaving behind the ARM_SMCCC_VERSION_1_3 and ARM_SMCCC_1_3_SVE_HINT
definitions, since these are simply definitions from the SMCCC
specification, and the latter is used in KVM via ARM_SMCCC_CALL_HINTS.
If we want to bring this back in future, we'll probably want to handle
this logic in C where we can use all the usual FPSIMD/SVE/SME helper
functions, and that'll likely require some rework of the SMCCC code
and/or its callers.
Fixes: cfa7ff959a ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20241106160448.2712997-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
[ Mark: fix conflicts in <linux/arm-smccc.h> ]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 751ecf6afd6568adc98f2a6052315552c0483d18 upstream.
The logic for handling SVE traps manipulates saved FPSIMD/SVE state
incorrectly, and a race with preemption can result in a task having
TIF_SVE set and TIF_FOREIGN_FPSTATE clear even though the live CPU state
is stale (e.g. with SVE traps enabled). This has been observed to result
in warnings from do_sve_acc() where SVE traps are not expected while
TIF_SVE is set:
| if (test_and_set_thread_flag(TIF_SVE))
| WARN_ON(1); /* SVE access shouldn't have trapped */
Warnings of this form have been reported intermittently, e.g.
https://lore.kernel.org/linux-arm-kernel/CA+G9fYtEGe_DhY2Ms7+L7NKsLYUomGsgqpdBj+QwDLeSg=JhGg@mail.gmail.com/https://lore.kernel.org/linux-arm-kernel/000000000000511e9a060ce5a45c@google.com/
The race can occur when the SVE trap handler is preempted before and
after manipulating the saved FPSIMD/SVE state, starting and ending on
the same CPU, e.g.
| void do_sve_acc(unsigned long esr, struct pt_regs *regs)
| {
| // Trap on CPU 0 with TIF_SVE clear, SVE traps enabled
| // task->fpsimd_cpu is 0.
| // per_cpu_ptr(&fpsimd_last_state, 0) is task.
|
| ...
|
| // Preempted; migrated from CPU 0 to CPU 1.
| // TIF_FOREIGN_FPSTATE is set.
|
| get_cpu_fpsimd_context();
|
| if (test_and_set_thread_flag(TIF_SVE))
| WARN_ON(1); /* SVE access shouldn't have trapped */
|
| sve_init_regs() {
| if (!test_thread_flag(TIF_FOREIGN_FPSTATE)) {
| ...
| } else {
| fpsimd_to_sve(current);
| current->thread.fp_type = FP_STATE_SVE;
| }
| }
|
| put_cpu_fpsimd_context();
|
| // Preempted; migrated from CPU 1 to CPU 0.
| // task->fpsimd_cpu is still 0
| // If per_cpu_ptr(&fpsimd_last_state, 0) is still task then:
| // - Stale HW state is reused (with SVE traps enabled)
| // - TIF_FOREIGN_FPSTATE is cleared
| // - A return to userspace skips HW state restore
| }
Fix the case where the state is not live and TIF_FOREIGN_FPSTATE is set
by calling fpsimd_flush_task_state() to detach from the saved CPU
state. This ensures that a subsequent context switch will not reuse the
stale CPU state, and will instead set TIF_FOREIGN_FPSTATE, forcing the
new state to be reloaded from memory prior to a return to userspace.
Fixes: cccb78ce89 ("arm64/sve: Rework SVE access trap to convert state in registers")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20241030-arm64-fpsimd-foreign-flush-v1-1-bd7bd66905a2@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 278a370c1766060d2144d6cf0b06c101e1043b6d upstream.
Netpoll will explicilty pass the polling call with a budget of 0 to
indicate it's clearing the Tx path only. For the gve_rx_poll and
gve_xdp_poll, they were mistakenly taking the 0 budget as the indication
to do all the work. Add check to avoid the rx path and xdp path being
called when budget is 0. And also avoid napi_complete_done being called
when budget is 0 for netpoll.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Ziwei Xiao <ziweixiao@google.com>
Link: https://lore.kernel.org/r/20231114004144.2022268-1-ziweixiao@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 25d7e84343.
The origin mainline patch fix a buffer overflow issue in
amdgpu_debugfs_gprwave_read(), but it has not been introduced in kernel
6.1 and older kernels. This patch add a check in a wrong function in the
same file.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit dfe6c5692fb5 ("ocfs2: fix the la space leak when
unmounting an ocfs2 volume").
In commit dfe6c5692fb5, the commit log "This bug has existed since the
initial OCFS2 code." is wrong. The correct introduction commit is
30dd3478c3cd ("ocfs2: correctly use ocfs2_find_next_zero_bit()").
The influence of commit dfe6c5692fb5 is that it provides a correct
fix for the latest kernel. however, it shouldn't be pushed to stable
branches. Let's use this commit to revert all branches that include
dfe6c5692fb5 and use a new fix method to fix commit 30dd3478c3cd.
Fixes: dfe6c5692fb5 ("ocfs2: fix the la space leak when unmounting an ocfs2 volume")
Signed-off-by: Heming Zhao <heming.zhao@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 291220451c775a054cedc4fab4578a1419eb6256 upstream.
In the probe function, it goes to 'release_mem' label and returns after
some procedure failure. But if the clocks (partial or all) have been
enabled previously, they would not be disabled in msdc_runtime_suspend,
since runtime PM is not yet enabled for this case.
That cause mmc related clocks always on during system suspend and block
suspend flow. Below log is from a SDCard issue of MT8196 chromebook, it
returns -ETIMEOUT while polling clock stable in the msdc_ungate_clock()
and probe failed, but the enabled clocks could not be disabled anyway.
[ 129.059253] clk_chk_dev_pm_suspend()
[ 129.350119] suspend warning: msdcpll is on
[ 129.354494] [ck_msdc30_1_sel : enabled, 1, 1, 191999939, ck_msdcpll_d2]
[ 129.362787] [ck_msdcpll_d2 : enabled, 1, 1, 191999939, msdcpll]
[ 129.371041] [ck_msdc30_1_ck : enabled, 1, 1, 191999939, ck_msdc30_1_sel]
[ 129.379295] [msdcpll : enabled, 1, 1, 383999878, clk26m]
Add a new 'release_clk' label and reorder the error handle functions to
make sure the clocks be disabled after probe failure.
Fixes: ffaea6ebfe ("mmc: mtk-sd: Use readl_poll_timeout instead of open-coded polling")
Fixes: 7a2fa8eed936 ("mmc: mtk-sd: use devm_mmc_alloc_host")
Signed-off-by: Andy-ld Lu <andy-ld.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable@vger.kernel.org
Message-ID: <20241107121215.5201-1-andy-ld.lu@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9044ad57b60b0556d42b6f8aa218a68865e810a4 upstream.
Don't flush all pending DbC data requests when an endpoint halts.
An endpoint may halt and xHC DbC triggers a STALL error event if there's
an issue with a bulk data transfer. The transfer should restart once xHC
DbC receives a ClearFeature(ENDPOINT_HALT) request from the host.
Once xHC DbC restarts it will start from the TRB pointed to by dequeue
field in the endpoint context, which might be the same TRB we got the
STALL event for. Turn the TRB to a no-op in this case to make sure xHC
DbC doesn't reuse and tries to retransmit this same TRB after we already
handled it, and gave its corresponding data request back.
Other STALL events might be completely bogus.
Lukasz Bartosik discovered that xHC DbC might issue spurious STALL events
if hosts sends a ClearFeature(ENDPOINT_HALT) request to non-halted
endpoints even without any active bulk transfers.
Assume STALL event is spurious if it reports 0 bytes transferred, and
the endpoint stopped on the STALLED TRB.
Don't give back the data request corresponding to the TRB in this case.
The halted status is per endpoint. Track it with a per endpoint flag
instead of the driver invented DbC wide DS_STALLED state.
DbC remains in DbC-Configured state even if endpoints halt. There is no
Stalled state in the DbC Port state Machine (xhci section 7.6.6)
Reported-by: Łukasz Bartosik <ukaszb@chromium.org>
Closes: https://lore.kernel.org/linux-usb/20240725074857.623299-1-ukaszb@chromium.org/
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3c7a1ede435e2e45177d7a490a85fb0a0ec96d1 upstream.
Patch series "mm/damon/vaddr: Fix issue in
damon_va_evenly_split_region()". v2.
According to the logic of damon_va_evenly_split_region(), currently
following split case would not meet the expectation:
Suppose DAMON_MIN_REGION=0x1000,
Case: Split [0x0, 0x3000) into 2 pieces, then the result would be
acutually 3 regions:
[0x0, 0x1000), [0x1000, 0x2000), [0x2000, 0x3000)
but NOT the expected 2 regions:
[0x0, 0x1000), [0x1000, 0x3000) !!!
The root cause is that when calculating size of each split piece in
damon_va_evenly_split_region():
`sz_piece = ALIGN_DOWN(sz_orig / nr_pieces, DAMON_MIN_REGION);`
both the dividing and the ALIGN_DOWN may cause loss of precision, then
each time split one piece of size 'sz_piece' from origin 'start' to 'end'
would cause more pieces are split out than expected!!!
To fix it, count for each piece split and make sure no more than
'nr_pieces'. In addition, add above case into damon_test_split_evenly().
And add 'nr_piece == 1' check in damon_va_evenly_split_region() for better
code readability and add a corresponding kunit testcase.
This patch (of 2):
According to the logic of damon_va_evenly_split_region(), currently
following split case would not meet the expectation:
Suppose DAMON_MIN_REGION=0x1000,
Case: Split [0x0, 0x3000) into 2 pieces, then the result would be
acutually 3 regions:
[0x0, 0x1000), [0x1000, 0x2000), [0x2000, 0x3000)
but NOT the expected 2 regions:
[0x0, 0x1000), [0x1000, 0x3000) !!!
The root cause is that when calculating size of each split piece in
damon_va_evenly_split_region():
`sz_piece = ALIGN_DOWN(sz_orig / nr_pieces, DAMON_MIN_REGION);`
both the dividing and the ALIGN_DOWN may cause loss of precision,
then each time split one piece of size 'sz_piece' from origin 'start' to
'end' would cause more pieces are split out than expected!!!
To fix it, count for each piece split and make sure no more than
'nr_pieces'. In addition, add above case into damon_test_split_evenly().
After this patch, damon-operations test passed:
# ./tools/testing/kunit/kunit.py run damon-operations
[...]
============== damon-operations (6 subtests) ===============
[PASSED] damon_test_three_regions_in_vmas
[PASSED] damon_test_apply_three_regions1
[PASSED] damon_test_apply_three_regions2
[PASSED] damon_test_apply_three_regions3
[PASSED] damon_test_apply_three_regions4
[PASSED] damon_test_split_evenly
================ [PASSED] damon-operations =================
Link: https://lkml.kernel.org/r/20241022083927.3592237-1-zhengyejian@huaweicloud.com
Link: https://lkml.kernel.org/r/20241022083927.3592237-2-zhengyejian@huaweicloud.com
Fixes: 3f49584b26 ("mm/damon: implement primitives for the virtual memory address spaces")
Signed-off-by: Zheng Yejian <zhengyejian@huaweicloud.com>
Reviewed-by: SeongJae Park <sj@kernel.org>
Cc: Fernand Sieber <sieberf@amazon.com>
Cc: Leonard Foerster <foersleo@amazon.de>
Cc: Shakeel Butt <shakeel.butt@linux.dev>
Cc: Ye Weihua <yeweihua4@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b29bf7119d6bbfd04aabb8d82b060fe2a33ef890 upstream.
The fix for a memory corruption contained a off-by-one error and
caused the compressor to fail in legit cases.
Cc: Kinsey Moore <kinsey.moore@oarcorp.com>
Cc: stable@vger.kernel.org
Fixes: fe051552f5078 ("jffs2: Prevent rtime decompress memory corruption")
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe051552f5078fa02d593847529a3884305a6ffe upstream.
The rtime decompression routine does not fully check bounds during the
entirety of the decompression pass and can corrupt memory outside the
decompression buffer if the compressed data is corrupted. This adds the
required check to prevent this failure mode.
Cc: stable@vger.kernel.org
Signed-off-by: Kinsey Moore <kinsey.moore@oarcorp.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.16 and prior to 6.13 KVM can't be used with FSDAX
guest memory (PMD pages). To reproduce the issue you need to reserve
guest memory with `memmap=` cmdline, create and mount FS in DAX mode
(tested both XFS and ext4), see doc link below. ndctl command for test:
ndctl create-namespace -v -e namespace1.0 --map=dev --mode=fsdax -a 2M
Then pass memory object to qemu like:
-m 8G -object memory-backend-file,id=ram0,size=8G,\
mem-path=/mnt/pmem/guestmem,share=on,prealloc=on,dump=off,align=2097152 \
-numa node,memdev=ram0,cpus=0-1
QEMU fails to run guest with error: kvm run failed Bad address
and there are two warnings in dmesg:
WARN_ON_ONCE(!page_count(page)) in kvm_is_zone_device_page() and
WARN_ON_ONCE(folio_ref_count(folio) <= 0) in try_grab_folio() (v6.6.63)
It looks like in the past assumption was made that pfn won't change from
faultin_pfn() to release_pfn_clean(), e.g. see
commit 4cd071d13c ("KVM: x86/mmu: Move calls to thp_adjust() down a level")
But kvm_page_fault structure made pfn part of mutable state, so
now release_pfn_clean() can take hugepage-adjusted pfn.
And it works for all cases (/dev/shm, hugetlb, devdax) except fsdax.
Apparently in fsdax mode faultin-pfn and adjusted-pfn may refer to
different folios, so we're getting get_page/put_page imbalance.
To solve this preserve faultin pfn in separate local variable
and pass it in kvm_release_pfn_clean().
Patch tested for all mentioned guest memory backends with tdp_mmu={0,1}.
No bug in upstream as it was solved fundamentally by
commit 8dd861cc07e2 ("KVM: x86/mmu: Put refcounted pages instead of blindly releasing pfns")
and related patch series.
Link: https://nvdimm.docs.kernel.org/2mib_fs_dax.html
Fixes: 2f6305dd56 ("KVM: MMU: change kvm_tdp_mmu_map() arguments to kvm_page_fault")
Co-developed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7602ffd1d5e8927fadd5187cb4aed2fdc9c47143 upstream.
When DISCARD frees an ITE, it does not invalidate the
corresponding ITE. In the scenario of continuous saves and
restores, there may be a situation where an ITE is not saved
but is restored. This is unreasonable and may cause restore
to fail. This patch clears the corresponding ITE when DISCARD
frees an ITE.
Cc: stable@vger.kernel.org
Fixes: eff484e029 ("KVM: arm64: vgic-its: ITT save and restore")
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
[Jing: Update with entry write helper]
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Link: https://lore.kernel.org/r/20241107214137.428439-6-jingzhangos@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9649129d33dca561305fc590a7c4ba8c3e5675a upstream.
vgic_its_save_device_tables will traverse its->device_list to
save DTE for each device. vgic_its_restore_device_tables will
traverse each entry of device table and check if it is valid.
Restore if valid.
But when MAPD unmaps a device, it does not invalidate the
corresponding DTE. In the scenario of continuous saves
and restores, there may be a situation where a device's DTE
is not saved but is restored. This is unreasonable and may
cause restore to fail. This patch clears the corresponding
DTE when MAPD unmaps a device.
Cc: stable@vger.kernel.org
Fixes: 57a9a11715 ("KVM: arm64: vgic-its: Device table save/restore")
Co-developed-by: Shusen Li <lishusen2@huawei.com>
Signed-off-by: Shusen Li <lishusen2@huawei.com>
Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com>
[Jing: Update with entry write helper]
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Link: https://lore.kernel.org/r/20241107214137.428439-5-jingzhangos@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32f123a3f3 upstream.
udf_getblk() has a single call site. Fold it there.
Signed-off-by: Jan Kara <jack@suse.cz>
[acsjakub: backport-adjusting changes
udf_getblk() has changed between 6.1 and the backported commit, namely
in commit 541e047b14 ("udf: Use udf_map_block() in udf_getblk()")
Backport using the form of udf_getblk present in 6.1., that means use
udf_get_block() instead of udf_map_block() and use dummy in buffer_new()
and buffer_mapped(). ]
Closes: https://syzkaller.appspot.com/bug?extid=a38e34ca637c224f4a79
Signed-off-by: Jakub Acs <acsjakub@amazon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9c7c5430bca36e9636eabbba0b3b53251479c7ab ]
Align the page tracking maximum message size with the device's
capability instead of relying on PAGE_SIZE.
This adjustment resolves a mismatch on systems where PAGE_SIZE is 64K,
but the firmware only supports a maximum message size of 4K.
Now that we rely on the device's capability for max_message_size, we
must account for potential future increases in its value.
Key considerations include:
- Supporting message sizes that exceed a single system page (e.g., an 8K
message on a 4K system).
- Ensuring the RQ size is adjusted to accommodate at least 4
WQEs/messages, in line with the device specification.
The above has been addressed as part of the patch.
Fixes: 79c3cf2799 ("vfio/mlx5: Init QP based resources for dirty tracking")
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Yingshun Cui <yicui@redhat.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20241205122654.235619-1-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 231825b2e1ff6ba799c5eaf396d3ab2354e37c6b ]
This reverts commit 5c26d2f1d3f5e4be3e196526bead29ecb139cf91.
It turns out that we can't do this, because while the old behavior of
ignoring ignorable code points was most definitely wrong, we have
case-folding filesystems with on-disk hash values with that wrong
behavior.
So now you can't look up those names, because they hash to something
different.
Of course, it's also entirely possible that in the meantime people have
created *new* files with the new ("more correct") case folding logic,
and reverting will just make other things break.
The correct solution is to not do case folding in filesystems, but
sadly, people seem to never really understand that. People still see it
as a feature, not a bug.
Reported-by: Qi Han <hanqi@vivo.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219586
Cc: Gabriel Krisman Bertazi <krisman@suse.de>
Requested-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c803c474c6c002d8ade68ebe99026cc39c37f85 ]
When activating a swap file we acquire the root's snapshot drew lock and
then check if the root is dead, failing and returning with -EPERM if it's
dead but without unlocking the root's snapshot lock. Fix this by adding
the missing unlock.
Fixes: 60021bd754 ("btrfs: prevent subvol with swapfile from being deleted")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e932c4ab38f072ce5894b2851fea8bc5754bb8e5 ]
Scheduler raises a SCHED_SOFTIRQ to trigger a load balancing event on
from the IPI handler on the idle CPU. If the SMP function is invoked
from an idle CPU via flush_smp_call_function_queue() then the HARD-IRQ
flag is not set and raise_softirq_irqoff() needlessly wakes ksoftirqd
because soft interrupts are handled before ksoftirqd get on the CPU.
Adding a trace_printk() in nohz_csd_func() at the spot of raising
SCHED_SOFTIRQ and enabling trace events for sched_switch, sched_wakeup,
and softirq_entry (for SCHED_SOFTIRQ vector alone) helps observing the
current behavior:
<idle>-0 [000] dN.1.: nohz_csd_func: Raising SCHED_SOFTIRQ from nohz_csd_func
<idle>-0 [000] dN.4.: sched_wakeup: comm=ksoftirqd/0 pid=16 prio=120 target_cpu=000
<idle>-0 [000] .Ns1.: softirq_entry: vec=7 [action=SCHED]
<idle>-0 [000] .Ns1.: softirq_exit: vec=7 [action=SCHED]
<idle>-0 [000] d..2.: sched_switch: prev_comm=swapper/0 prev_pid=0 prev_prio=120 prev_state=R ==> next_comm=ksoftirqd/0 next_pid=16 next_prio=120
ksoftirqd/0-16 [000] d..2.: sched_switch: prev_comm=ksoftirqd/0 prev_pid=16 prev_prio=120 prev_state=S ==> next_comm=swapper/0 next_pid=0 next_prio=120
...
Use __raise_softirq_irqoff() to raise the softirq. The SMP function call
is always invoked on the requested CPU in an interrupt handler. It is
guaranteed that soft interrupts are handled at the end.
Following are the observations with the changes when enabling the same
set of events:
<idle>-0 [000] dN.1.: nohz_csd_func: Raising SCHED_SOFTIRQ for nohz_idle_balance
<idle>-0 [000] dN.1.: softirq_raise: vec=7 [action=SCHED]
<idle>-0 [000] .Ns1.: softirq_entry: vec=7 [action=SCHED]
No unnecessary ksoftirqd wakeups are seen from idle task's context to
service the softirq.
Fixes: b2a02fc43a ("smp: Optimize send_call_function_single_ipi()")
Closes: https://lore.kernel.org/lkml/fcf823f-195e-6c9a-eac3-25f870cb35ac@inria.fr/ [1]
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Suggested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/20241119054432.6405-5-kprateek.nayak@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff47a0acfcce309cf9e175149c75614491953c8f ]
Commit b2a02fc43a ("smp: Optimize send_call_function_single_ipi()")
optimizes IPIs to idle CPUs in TIF_POLLING_NRFLAG mode by setting the
TIF_NEED_RESCHED flag in idle task's thread info and relying on
flush_smp_call_function_queue() in idle exit path to run the
call-function. A softirq raised by the call-function is handled shortly
after in do_softirq_post_smp_call_flush() but the TIF_NEED_RESCHED flag
remains set and is only cleared later when schedule_idle() calls
__schedule().
need_resched() check in _nohz_idle_balance() exists to bail out of load
balancing if another task has woken up on the CPU currently in-charge of
idle load balancing which is being processed in SCHED_SOFTIRQ context.
Since the optimization mentioned above overloads the interpretation of
TIF_NEED_RESCHED, check for idle_cpu() before going with the existing
need_resched() check which can catch a genuine task wakeup on an idle
CPU processing SCHED_SOFTIRQ from do_softirq_post_smp_call_flush(), as
well as the case where ksoftirqd needs to be preempted as a result of
new task wakeup or slice expiry.
In case of PREEMPT_RT or threadirqs, although the idle load balancing
may be inhibited in some cases on the ilb CPU, the fact that ksoftirqd
is the only fair task going back to sleep will trigger a newidle balance
on the CPU which will alleviate some imbalance if it exists if idle
balance fails to do so.
Fixes: b2a02fc43a ("smp: Optimize send_call_function_single_ipi()")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20241119054432.6405-4-kprateek.nayak@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea9cffc0a154124821531991d5afdd7e8b20d7aa ]
The need_resched() check currently in nohz_csd_func() can be tracked
to have been added in scheduler_ipi() back in 2011 via commit
ca38062e57 ("sched: Use resched IPI to kick off the nohz idle balance")
Since then, it has travelled quite a bit but it seems like an idle_cpu()
check currently is sufficient to detect the need to bail out from an
idle load balancing. To justify this removal, consider all the following
case where an idle load balancing could race with a task wakeup:
o Since commit f3dd3f6745 ("sched: Remove the limitation of WF_ON_CPU
on wakelist if wakee cpu is idle") a target perceived to be idle
(target_rq->nr_running == 0) will return true for
ttwu_queue_cond(target) which will offload the task wakeup to the idle
target via an IPI.
In all such cases target_rq->ttwu_pending will be set to 1 before
queuing the wake function.
If an idle load balance races here, following scenarios are possible:
- The CPU is not in TIF_POLLING_NRFLAG mode in which case an actual
IPI is sent to the CPU to wake it out of idle. If the
nohz_csd_func() queues before sched_ttwu_pending(), the idle load
balance will bail out since idle_cpu(target) returns 0 since
target_rq->ttwu_pending is 1. If the nohz_csd_func() is queued after
sched_ttwu_pending() it should see rq->nr_running to be non-zero and
bail out of idle load balancing.
- The CPU is in TIF_POLLING_NRFLAG mode and instead of an actual IPI,
the sender will simply set TIF_NEED_RESCHED for the target to put it
out of idle and flush_smp_call_function_queue() in do_idle() will
execute the call function. Depending on the ordering of the queuing
of nohz_csd_func() and sched_ttwu_pending(), the idle_cpu() check in
nohz_csd_func() should either see target_rq->ttwu_pending = 1 or
target_rq->nr_running to be non-zero if there is a genuine task
wakeup racing with the idle load balance kick.
o The waker CPU perceives the target CPU to be busy
(targer_rq->nr_running != 0) but the CPU is in fact going idle and due
to a series of unfortunate events, the system reaches a case where the
waker CPU decides to perform the wakeup by itself in ttwu_queue() on
the target CPU but target is concurrently selected for idle load
balance (XXX: Can this happen? I'm not sure, but we'll consider the
mother of all coincidences to estimate the worst case scenario).
ttwu_do_activate() calls enqueue_task() which would increment
"rq->nr_running" post which it calls wakeup_preempt() which is
responsible for setting TIF_NEED_RESCHED (via a resched IPI or by
setting TIF_NEED_RESCHED on a TIF_POLLING_NRFLAG idle CPU) The key
thing to note in this case is that rq->nr_running is already non-zero
in case of a wakeup before TIF_NEED_RESCHED is set which would
lead to idle_cpu() check returning false.
In all cases, it seems that need_resched() check is unnecessary when
checking for idle_cpu() first since an impending wakeup racing with idle
load balancer will either set the "rq->ttwu_pending" or indicate a newly
woken task via "rq->nr_running".
Chasing the reason why this check might have existed in the first place,
I came across Peter's suggestion on the fist iteration of Suresh's
patch from 2011 [1] where the condition to raise the SCHED_SOFTIRQ was:
sched_ttwu_do_pending(list);
if (unlikely((rq->idle == current) &&
rq->nohz_balance_kick &&
!need_resched()))
raise_softirq_irqoff(SCHED_SOFTIRQ);
Since the condition to raise the SCHED_SOFIRQ was preceded by
sched_ttwu_do_pending() (which is equivalent of sched_ttwu_pending()) in
the current upstream kernel, the need_resched() check was necessary to
catch a newly queued task. Peter suggested modifying it to:
if (idle_cpu() && rq->nohz_balance_kick && !need_resched())
raise_softirq_irqoff(SCHED_SOFTIRQ);
where idle_cpu() seems to have replaced "rq->idle == current" check.
Even back then, the idle_cpu() check would have been sufficient to catch
a new task being enqueued. Since commit b2a02fc43a ("smp: Optimize
send_call_function_single_ipi()") overloads the interpretation of
TIF_NEED_RESCHED for TIF_POLLING_NRFLAG idling, remove the
need_resched() check in nohz_csd_func() to raise SCHED_SOFTIRQ based
on Peter's suggestion.
Fixes: b2a02fc43a ("smp: Optimize send_call_function_single_ipi()")
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20241119054432.6405-3-kprateek.nayak@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6a690e0c9 ]
KASAN suppresses reports for bad accesses done by the KASAN reporting
code. The reporting code might access poisoned memory for reporting
purposes.
Software KASAN modes do this by suppressing reports during reporting via
current->kasan_depth, the same way they suppress reports during accesses
to poisoned slab metadata.
Hardware Tag-Based KASAN does not use current->kasan_depth, and instead
resets pointer tags for accesses to poisoned memory done by the reporting
code.
Despite that, a recursive report can still happen:
1. On hardware with faulty MTE support. This was observed by Weizhao
Ouyang on a faulty hardware that caused memory tags to randomly change
from time to time.
2. Theoretically, due to a previous MTE-undetected memory corruption.
A recursive report can happen via:
1. Accessing a pointer with a non-reset tag in the reporting code, e.g.
slab->slab_cache, which is what Weizhao Ouyang observed.
2. Theoretically, via external non-annotated routines, e.g. stackdepot.
To resolve this issue, resetting tags for all of the pointers in the
reporting code and all the used external routines would be impractical.
Instead, disable tag checking done by the CPU for the duration of KASAN
reporting for Hardware Tag-Based KASAN.
Without this fix, Hardware Tag-Based KASAN reporting code might deadlock.
[andreyknvl@google.com: disable preemption instead of migration, fix comment typo]
Link: https://lkml.kernel.org/r/d14417c8bc5eea7589e99381203432f15c0f9138.1680114854.git.andreyknvl@google.com
Link: https://lkml.kernel.org/r/59f433e00f7fa985e8bf9f7caf78574db16b67ab.1678491668.git.andreyknvl@google.com
Fixes: 2e903b9147 ("kasan, arm64: implement HW_TAGS runtime")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: Weizhao Ouyang <ouyangweizhao@zeku.com>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Evgenii Stepanov <eugenis@google.com>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: e30a0361b851 ("kasan: make report_lock a raw spinlock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eb75ce7527129d7f1fee6951566af409a37a1c4 ]
syzbot triggered the following WARN_ON:
WARNING: CPU: 0 PID: 16 at io_uring/tctx.c:51 __io_uring_free+0xfa/0x140 io_uring/tctx.c:51
which is the
WARN_ON_ONCE(!xa_empty(&tctx->xa));
sanity check in __io_uring_free() when a io_uring_task is going through
its final put. The syzbot test case includes injecting memory allocation
failures, and it very much looks like xa_store() can fail one of its
memory allocations and end up with ->head being non-NULL even though no
entries exist in the xarray.
Until this issue gets sorted out, work around it by attempting to
iterate entries in our xarray, and WARN_ON_ONCE() if one is found.
Reported-by: syzbot+cc36d44ec9f368e443d3@syzkaller.appspotmail.com
Link: https://lore.kernel.org/io-uring/673c1643.050a0220.87769.0066.GAE@google.com/
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a6efab33eab4e973db26d9f90c3e97a7a82e399 ]
On my device reading entirety of /sys/devices/pnp0/00:03/cmos_nvram0/nvmem
takes about 9 msec during which time interrupts are off on the CPU that
does the read and the thread that performs the read can not be migrated
or preempted by another higher priority thread (RT or not).
Allow readers and writers be preempted by taking and releasing rtc_lock
spinlock for each individual byte read or written rather than once per
read/write request.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Link: https://lore.kernel.org/r/Zxv8QWR21AV4ztC5@google.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7738a7ab9d12c5371ed97114ee2132d4512e9fd5 ]
Add a quirk similar to eeprom_93xx46 to add an extra clock cycle before
reading data from the EEPROM.
The 93Cx6 family of EEPROMs output a "dummy 0 bit" between the writing
of the op-code/address from the host to the EEPROM and the reading of
the actual data from the EEPROM.
More info can be found on page 6 of the AT93C46 datasheet (linked below).
Similar notes are found in other 93xx6 datasheets.
In summary the read operation for a 93Cx6 EEPROM is:
Write to EEPROM: 110[A5-A0] (9 bits)
Read from EEPROM: 0[D15-D0] (17 bits)
Where:
110 is the start bit and READ OpCode
[A5-A0] is the address to read from
0 is a "dummy bit" preceding the actual data
[D15-D0] is the actual data.
Looking at the READ timing diagrams in the 93Cx6 datasheets the dummy
bit should be clocked out on the last address bit clock cycle meaning it
should be discarded naturally.
However, depending on the hardware configuration sometimes this dummy
bit is not discarded. This is the case with Exar PCI UARTs which require
an extra clock cycle between sending the address and reading the data.
Datasheet: https://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-5193-SEEPROM-AT93C46D-Datasheet.pdf
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/0f23973efefccd2544705a0480b4ad4c2353e407.1727880931.git.pnewman@connecttech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf89c9434af122f28a3552e6f9cc5158c33ce50a ]
On some powermacs `escc` nodes are missing `#size-cells` properties,
which is deprecated and now triggers a warning at boot since commit
045b14ca5c36 ("of: WARN on deprecated #address-cells/#size-cells
handling").
For example:
Missing '#size-cells' in /pci@f2000000/mac-io@c/escc@13000
WARNING: CPU: 0 PID: 0 at drivers/of/base.c:133 of_bus_n_size_cells+0x98/0x108
Hardware name: PowerMac3,1 7400 0xc0209 PowerMac
...
Call Trace:
of_bus_n_size_cells+0x98/0x108 (unreliable)
of_bus_default_count_cells+0x40/0x60
__of_get_address+0xc8/0x21c
__of_address_to_resource+0x5c/0x228
pmz_init_port+0x5c/0x2ec
pmz_probe.isra.0+0x144/0x1e4
pmz_console_init+0x10/0x48
console_init+0xcc/0x138
start_kernel+0x5c4/0x694
As powermacs boot via prom_init it's possible to add the missing
properties to the device tree during boot, avoiding the warning. Note
that `escc-legacy` nodes are also missing `#size-cells` properties, but
they are skipped by the macio driver, so leave them alone.
Depends-on: 045b14ca5c36 ("of: WARN on deprecated #address-cells/#size-cells handling")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20241126025710.591683-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fbd66d8254cedfd1218393f39d83b6c07a01917 ]
Fix the dtc warnings:
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:68.16-416.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:68.16-416.5: Warning (interrupt_provider): /bus@10000000/pci@1a000000: '#interrupt-cells' found, but node is not an interrupt provider
arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dtb: Warning (interrupt_map): Failed prerequisite 'interrupt_provider'
And a runtime warning introduced in commit 045b14ca5c36 ("of: WARN on
deprecated #address-cells/#size-cells handling"):
WARNING: CPU: 0 PID: 1 at drivers/of/base.c:106 of_bus_n_addr_cells+0x9c/0xe0
Missing '#address-cells' in /bus@10000000/pci@1a000000/pci_bridge@9,0
The fix is similar to commit d89a415ff8d5 ("MIPS: Loongson64: DTS: Fix PCIe
port nodes for ls7a"), which has fixed the issue for ls2k (despite its
subject mentions ls7a).
Signed-off-by: Xi Ruoyao <xry111@xry111.site>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548f48b66c0c5d4b9795a55f304b7298cde2a025 ]
As per USBSTS register description about UEI:
When completion of a USB transaction results in an error condition, this
bit is set by the Host/Device Controller. This bit is set along with the
USBINT bit, if the TD on which the error interrupt occurred also had its
interrupt on complete (IOC) bit set.
UI is set only when IOC set. Add checking UEI to fix miss call
isr_tr_complete_handler() when IOC have not set and transfer error happen.
Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa46a3736afcb7b0793766d22479b8b99fc1b322 ]
Wangxun FF5xxx NICs are similar to SFxxx, RP1000 and RP2000 NICs. They may
be multi-function devices, but they do not advertise an ACS capability.
But the hardware does isolate FF5xxx functions as though it had an ACS
capability and PCI_ACS_RR and PCI_ACS_CR were set in the ACS Control
register, i.e., all peer-to-peer traffic is directed upstream instead of
being routed internally.
Add ACS quirk for FF5xxx NICs in pci_quirk_wangxun_nic_acs() so the
functions can be in independent IOMMU groups.
Link: https://lore.kernel.org/r/E16053DB2B80E9A5+20241115024604.30493-1-mengyuanlou@net-swift.com
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fa046449a82a7d0f6d9721dd83e348816038444 ]
The "bus" and "cxl_bus" reset methods reset a device by asserting Secondary
Bus Reset on the bridge leading to the device. These only work if the
device is the only device below the bridge.
Add a sysfs 'reset_subordinate' attribute on bridges that can assert
Secondary Bus Reset regardless of how many devices are below the bridge.
This resets all the devices below a bridge in a single command, including
the locking and config space save/restore that reset methods normally do.
This may be the only way to reset devices that don't support other reset
methods (ACPI, FLR, PM reset, etc).
Link: https://lore.kernel.org/r/20241025222755.3756162-1-kbusch@meta.com
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: commit log, add capable(CAP_SYS_ADMIN) check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b96b895127b7c0aed63d82c974b46340e8466c1 ]
Some computers with CPUs that lack Thunderbolt features use discrete
Thunderbolt chips to add Thunderbolt functionality. These Thunderbolt
chips are located within the chassis; between the Root Port labeled
ExternalFacingPort and the USB-C port.
These Thunderbolt PCIe devices should be labeled as fixed and trusted, as
they are built into the computer. Otherwise, security policies that rely on
those flags may have unintended results, such as preventing USB-C ports
from enumerating.
Detect the above scenario through the process of elimination.
1) Integrated Thunderbolt host controllers already have Thunderbolt
implemented, so anything outside their external facing Root Port is
removable and untrusted.
Detect them using the following properties:
- Most integrated host controllers have the "usb4-host-interface"
ACPI property, as described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#mapping-native-protocols-pcie-displayport-tunneled-through-usb4-to-usb4-host-routers
- Integrated Thunderbolt PCIe Root Ports before Alder Lake do not
have the "usb4-host-interface" ACPI property. Identify those by
their PCI IDs instead.
2) If a Root Port does not have integrated Thunderbolt capabilities, but
has the "ExternalFacingPort" ACPI property, that means the
manufacturer has opted to use a discrete Thunderbolt host controller
that is built into the computer.
This host controller can be identified by virtue of being located
directly below an external-facing Root Port that lacks integrated
Thunderbolt. Label it as trusted and fixed.
Everything downstream from it is untrusted and removable.
The "ExternalFacingPort" ACPI property is described here:
https://learn.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-externally-exposed-pcie-root-ports
Link: https://lore.kernel.org/r/20240910-trust-tbt-fix-v5-1-7a7a42a5f496@chromium.org
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Esther Shimanovich <eshimanovich@chromium.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ca2738174e4ee44edb2ab2d86ce74f015a0cc32 ]
Bus cleanup path in DMA mode may trigger a RING_OP_STAT interrupt when
the ring is being stopped. Depending on timing between ring stop request
completion, interrupt handler removal and code execution this may lead
to a NULL pointer dereference in hci_dma_irq_handler() if it gets to run
after the io_data pointer is set to NULL in hci_dma_cleanup().
Prevent this my masking the ring interrupts before ring stop request.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20240920144432.62370-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5c367ef8287fb4d235c46a2f8c8d68715f3a0ca ]
creating a large files during checkpoint disable until it runs out of
space and then delete it, then remount to enable checkpoint again, and
then unmount the filesystem triggers the f2fs_bug_on as below:
------------[ cut here ]------------
kernel BUG at fs/f2fs/inode.c:896!
CPU: 2 UID: 0 PID: 1286 Comm: umount Not tainted 6.11.0-rc7-dirty #360
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:f2fs_evict_inode+0x58c/0x610
Call Trace:
__die_body+0x15/0x60
die+0x33/0x50
do_trap+0x10a/0x120
f2fs_evict_inode+0x58c/0x610
do_error_trap+0x60/0x80
f2fs_evict_inode+0x58c/0x610
exc_invalid_op+0x53/0x60
f2fs_evict_inode+0x58c/0x610
asm_exc_invalid_op+0x16/0x20
f2fs_evict_inode+0x58c/0x610
evict+0x101/0x260
dispose_list+0x30/0x50
evict_inodes+0x140/0x190
generic_shutdown_super+0x2f/0x150
kill_block_super+0x11/0x40
kill_f2fs_super+0x7d/0x140
deactivate_locked_super+0x2a/0x70
cleanup_mnt+0xb3/0x140
task_work_run+0x61/0x90
The root cause is: creating large files during disable checkpoint
period results in not enough free segments, so when writing back root
inode will failed in f2fs_enable_checkpoint. When umount the file
system after enabling checkpoint, the root inode is dirty in
f2fs_evict_inode function, which triggers BUG_ON. The steps to
reproduce are as follows:
dd if=/dev/zero of=f2fs.img bs=1M count=55
mount f2fs.img f2fs_dir -o checkpoint=disable:10%
dd if=/dev/zero of=big bs=1M count=50
sync
rm big
mount -o remount,checkpoint=enable f2fs_dir
umount f2fs_dir
Let's redirty inode when there is not free segments during checkpoint
is disable.
Signed-off-by: Qi Han <hanqi@vivo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 571f8b3f866a6d990a50fe5c89fe0ea78784d70b ]
This patch makes the dot parser used by dot2c and dot2k slightly more
robust, namely:
* allows parsing files with the gv extension (GraphViz)
* correctly parses edges with any indentation
* used to work only with a single character (e.g. '\t')
Additionally it fixes a couple of warnings reported by pylint such as
wrong indentation and comparison to False instead of `not ...`
Link: https://lore.kernel.org/20241017064238.41394-2-gmonaco@redhat.com
Signed-off-by: Gabriele Monaco <gmonaco@redhat.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f69b0187f8745a7a9584f6b13f5e792594b88b2e ]
Like commit f1f047bd7c ("smb: client: Fix -Wstringop-overflow issues"),
adjust the memcpy() destination address to be based off the surrounding
object rather than based off the 4-byte "Protocol" member. This avoids a
build-time warning when compiling under CONFIG_FORTIFY_SOURCE with GCC 15:
In function 'fortify_memcpy_chk',
inlined from 'CIFSSMBSetPathInfo' at ../fs/smb/client/cifssmb.c:5358:2:
../include/linux/fortify-string.h:571:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
571 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Kees Cook <kees@kernel.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b61352101470f8b68c98af674e187cfaa7c43504 ]
When nd_dax is NULL, nd_pfn is consequently NULL as well. Nevertheless,
it is inadvisable to perform pointer arithmetic or address-taking on a
NULL pointer.
Introduce the nd_dax_devinit() function to enhance the code's logic and
improve its readability.
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/20241108085526.527957-1-yiyang13@huawei.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
