[ Upstream commit 082744433f ]
firmware should be waked up by start or configure command,
but there is a very small chance that firmware failed to wakeup.
in such case, try to wakeup firmware again by sending a noop command
Fixes: 6de8d628df ("media: amphion: add v4l2 m2m vpu decoder stateful driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 614f6e35a9 ]
This allows the device to probe and register its async subdev without
a sensor attached.
The rationale is that the parent driver might otherwise wait for the
subdev to be registered when it should be available (from the fwnode
graph endpoint perspective). This is generally not problematic when
the MIPI CSI-2 bridge is the only device attached to the parent, but
in the case of a CSI controller that can feed from both MIPI CSI-2
and parallel, it would prevent using the parallel sensor due to the
parent waiting for the MIPI CSI-2 subdev to register.
Fixes: 576d196c52 ("media: sunxi: Add support for the A83T MIPI CSI-2 controller")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67182951f1 ]
This allows the device to probe and register its async subdev without
a sensor attached.
The rationale is that the parent driver might otherwise wait for the
subdev to be registered when it should be available (from the fwnode
graph endpoint perspective). This is generally not problematic when
the MIPI CSI-2 bridge is the only device attached to the parent, but
in the case of a CSI controller that can feed from both MIPI CSI-2
and parallel, it would prevent using the parallel sensor due to the
parent waiting for the MIPI CSI-2 subdev to register.
Fixes: af54b4f4c1 ("media: sunxi: Add support for the A31 MIPI CSI-2 controller")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8985fc724b ]
The bridge needs both its pads connected to be able to stream data.
Enforcing this is useful to produce an error when no sensor is
connected.
Fixes: 576d196c52 ("media: sunxi: Add support for the A83T MIPI CSI-2 controller")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f042b08b83 ]
The bridge needs both its pads connected to be able to stream data.
Enforcing this is useful to produce an error when no sensor is
connected.
Fixes: af54b4f4c1 ("media: sunxi: Add support for the A31 MIPI CSI-2 controller")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1e5250094 ]
When running as a Xen PV guest there is no need for setting up the
realmode trampoline, as realmode isn't supported in this environment.
Trying to setup the trampoline has been proven to be problematic in
some cases, especially when trying to debug early boot problems with
Xen requiring to keep the EFI boot-services memory mapped (some
firmware variants seem to claim basically all memory below 1Mb for boot
services).
Introduce new x86_platform_ops operations for that purpose, which can
be set to a NOP by the Xen PV specific kernel boot code.
[ bp: s/call_init_real_mode/do_init_real_mode/ ]
Fixes: 084ee1c641 ("x86, realmode: Relocator for realmode code")
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20221123114523.3467-1-jgross@suse.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a574359e2e ]
In dvb_register_frontend(), dvb_register_device() is possible to fail
but its return value is ignored.
It will cause use-after-free when module is removed, because in
dvb_unregister_frontend() it tries to unregister a not registered
device.
BUG: KASAN: use-after-free in dvb_remove_device+0x18b/0x1f0 [dvb_core]
Read of size 4 at addr ffff88800dff4824 by task rmmod/428
CPU: 3 PID: 428 Comm: rmmod
Call Trace:
<TASK>
...
dvb_remove_device+0x18b/0x1f0 [dvb_core]
dvb_unregister_frontend+0x7b/0x130 [dvb_core]
vidtv_bridge_remove+0x6e/0x160 [dvb_vidtv_bridge]
...
Fix this by catching return value of dvb_register_device().
However the fe->refcount can't be put to zero immediately, because
there are still modules calling dvb_frontend_detach() when
dvb_register_frontend() fails.
Link: https://lore.kernel.org/linux-media/20221108033005.169095-1-chenzhongjin@huawei.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7fa365ff6 ]
There is no occurrence of the hdmi oscillator in the reference manual
(document IMX8MNRM Rev 2, 07/2022). Further, if we consider the indexes
76-81 and 134 of the "Clock Root" table of chapter 5 of the RM, there is
no entry for the source select bits 101b, which is the setting referenced
by "osc_hdmi".
Fix by renaming "osc_hdmi" with "dummy", a clock which has already been
used for missing source select bits.
Tested on the BSH SystemMaster (SMM) S2 board.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221117113637.1978703-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a429c60bae ]
The IMX8MN platform does not have any video processing unit (VPU), and
indeed in the reference manual (document IMX8MNRM Rev 2, 07/2022) there
is no occurrence of its pll. From an analysis of the code and the RM
itself, I think vpu pll is used instead of m7 alternate pll, probably
for copy and paste of code taken from modules of similar architectures.
As an example for all, if we consider the second row of the "Clock Root"
table of chapter 5 (Clocks and Power Management) of the RM:
Clock Root offset Source Select (CCM_TARGET_ROOTn[MUX])
... ... ...
ARM_M7_CLK_ROOT 0x8080 000 - 24M_REF_CLK
001 - SYSTEM_PLL2_DIV5
010 - SYSTEM_PLL2_DIV4
011 - M7_ALT_PLL_CLK
100 - SYSTEM_PLL1_CLK
101 - AUDIO_PLL1_CLK
110 - VIDEO_PLL_CLK
111 - SYSTEM_PLL3_CLK
... ... ...
but in the source code, the imx8mn_m7_sels clocks list contains vpu_pll
for the source select bits 011b.
So, let's rename "vpu_pll" to "m7_alt_pll" to be consistent with the RM.
The IMX8MN_VPU_* constants have not been removed to ensure backward
compatibility of the patch.
No functional changes intended.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221117113637.1978703-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e208ad015f ]
The mt9p031_init_cfg() already calls __mt9p031_get_pad_crop(), which
correctly calls v4l2_subdev_get_try_crop() on V4L2_SUBDEV_FORMAT_TRY
or returns &mt9p031->crop on V4L2_SUBDEV_FORMAT_ACTIVE. No need to
call v4l2_subdev_get_try_crop() in mt9p031_init_cfg() again in case
of both V4L2_SUBDEV_FORMAT_TRY and V4L2_SUBDEV_FORMAT_ACTIVE.
This also fixes a splat generated by this call since commit
2ba3e38517 ("media: v4l: subdev: Fail graciously when getting try data for NULL state")
because v4l2_subdev_get_try_crop() is called with sd_state = NULL
in mt9p031_init_cfg().
Fixes: 69681cd041 ("media: mt9p031: Move open subdev op init code into init_cfg")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cccc08a95c ]
Commit 9babbbaaeb ("media: imx: imx7-media-csi: Use dual sampling for
YUV 1X16") set BIT_MIPI_DOUBLE_CMPNT in the CR18 register for 16-bit YUV
formats in imx7_csi_configure(). The CR18 register is always updated
with read-modify-write cycles, so if a 16-bit YUV format is selected,
the bit will stay set forever, even if the format is changed. Fix it by
clearing the bit at the beginning of the imx7_csi_configure() function.
While at it, swap two of the bits being cleared to match the MSB to LSB
order. This doesn't cause any functional change.
Fixes: 9babbbaaeb ("media: imx: imx7-media-csi: Use dual sampling for YUV 1X16")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 813ceef062 ]
The function send_packet() has a race condition as follows:
func send_packet()
{
// do work
call usb_submit_urb()
mutex_unlock()
wait_for_event_interruptible() <-- lock gone
mutex_lock()
}
func vfd_write()
{
mutex_lock()
call send_packet() <- prev call is not completed
mutex_unlock()
}
When the mutex is unlocked and the function send_packet() waits for the
call to complete, vfd_write() can start another call, which leads to the
"URB submitted while active" warning in usb_submit_urb().
Fix this by removing the mutex_unlock() call in send_packet() and using
mutex_lock_interruptible().
Link: https://syzkaller.appspot.com/bug?id=e378e6a51fbe6c5cc43e34f131cc9a315ef0337e
Fixes: 21677cfc56 ("V4L/DVB: ir-core: add imon driver")
Reported-by: syzbot+0c3cb6dc05fbbdc3ad66@syzkaller.appspotmail.com
Signed-off-by: Gautam Menghani <gautammenghani201@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d89cf6ff2 ]
SND_SOC_QCOM_COMMON depends on SOUNDWIRE for some symbols but this
is not explicitly specified using Kconfig depends. On the other hand
SND_SOC_QCOM_COMMON is also directly selected by the sound card
Kconfigs, this could result in various combinations and some symbols
ending up in modules and soundcard that uses those symbols as in-build
driver.
Fix these issues by explicitly specifying the dependencies of
SND_SOC_QCOM_COMMON and also use imply a to select SND_SOC_QCOM_COMMON
so that the symbol is selected based on its dependencies.
Also remove dummy stubs in common.c around CONFIG_SOUNDWIRE
Fixes: 3bd975f3ae ("ASoC: qcom: sm8250: move some code to common")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221124140351.407506-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8a65ab2f3 ]
Before this change when a bond in mode 2 lost link, all of its slaves
lost link, the bonding device would never recover even after the
expiration of updelay. This change removes the updelay when the bond
currently has no usable links. Conforming to bonding.txt section 13.1
paragraph 4.
Fixes: 41f8910040 ("bonding: ignore updelay param when there is no active slave")
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b85e285e3d ]
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak.
Fixes: 3f12acc8d6 ("drm/amdgpu: put the audio codec into suspend state before gpu reset V3")
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf59e1e4c7 ]
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in sound/core/seq/seq_clientmgr.c:509:22
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x44
__ubsan_handle_shift_out_of_bounds+0x1e7/0x208
snd_seq_deliver_single_event.constprop.21+0x191/0x2f0
snd_seq_deliver_event+0x1a2/0x350
snd_seq_kernel_client_dispatch+0x8b/0xb0
snd_seq_client_notify_subscription+0x72/0xa0
snd_seq_ioctl_subscribe_port+0x128/0x160
snd_seq_kernel_client_ctl+0xce/0xf0
snd_seq_oss_create_client+0x109/0x15b
alsa_seq_oss_init+0x11c/0x1aa
do_one_initcall+0x80/0x440
kernel_init_freeable+0x370/0x3c3
kernel_init+0x1b/0x190
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Baisong Zhong <zhongbaisong@huawei.com>
Link: https://lore.kernel.org/r/20221121111630.3119259-1-zhongbaisong@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5172e6245 ]
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in sound/core/pcm_native.c:2676:21
left shift of 1 by 31 places cannot be represented in type 'int'
...
Call Trace:
<TASK>
dump_stack_lvl+0x8d/0xcf
ubsan_epilogue+0xa/0x44
__ubsan_handle_shift_out_of_bounds+0x1e7/0x208
snd_pcm_open_substream+0x9f0/0xa90
snd_pcm_oss_open.part.26+0x313/0x670
snd_pcm_oss_open+0x30/0x40
soundcore_open+0x18b/0x2e0
chrdev_open+0xe2/0x270
do_dentry_open+0x2f7/0x620
path_openat+0xd66/0xe70
do_filp_open+0xe3/0x170
do_sys_openat2+0x357/0x4a0
do_sys_open+0x87/0xd0
do_syscall_64+0x34/0x80
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Baisong Zhong <zhongbaisong@huawei.com>
Link: https://lore.kernel.org/r/20221121110044.3115686-1-zhongbaisong@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d013910df ]
This is no bugfix (so no Fixes: tag is necessary) as it is
taken care of in hid_sensor_custom_add_attributes().
The motivation for this patch is that:
hid_sensor_custom_field.attr_name and
hid_sensor_custom_field.attrs
has the size of HID_CUSTOM_TOTAL_ATTRS and used in same context.
We compare against HID_CUSTOM_TOTAL_ATTRS when
looping through hid_custom_attrs.
We will silent the smatch error:
hid_sensor_custom_add_attributes() error: buffer overflow
'hid_custom_attrs' 8 <= 10
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9984fbf55b ]
HID-RMI is special in the sense that it does not carry HID events
directly, but rather uses HID protocol as a wrapper/transport for RMI
protocol. Therefore we should not assume that all data coming from the
device via interrupt is associated with user activity and report wakeup
event indiscriminately, but rather let HID-RMI do that when appropriate.
HID-RMI devices tag responses to the commands issued by the host as
RMI_READ_DATA_REPORT_ID whereas motion and other input events from the
device are tagged as RMI_ATTN_REPORT_ID. Change hid-rmi to report wakeup
events when receiving the latter packets. This allows ChromeOS to
accurately identify wakeup source and make correct decision on the mode
of the resume the system should take ("dark" where the display stays off
vs normal one).
Fixes: d951ae1ce8 ("HID: i2c-hid: Report wakeup events")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a5160d4d8 ]
bpf_iter_attach_cgroup() has already acquired an extra reference for the
start cgroup, but the reference may be released if the iterator link fd
is closed after the creation of iterator fd, and it may lead to
user-after-free problem when reading the iterator fd.
An alternative fix is pinning iterator link when opening iterator,
but it will make iterator link being still visible after the close of
iterator link fd and the behavior is different with other link types, so
just fixing it by acquiring another reference for the start cgroup.
Fixes: d4ccaf58a8 ("bpf: Introduce cgroup iter")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20221121073440.1828292-2-houtao@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
