[ Upstream commit a7d82367da ]
In the blamed commit, it was not noticed that one implementation of
chip->info->ops->phylink_get_caps(), called by mv88e6xxx_get_caps(),
may access hardware registers, and in doing so, it takes the
mv88e6xxx_reg_lock(). Namely, this is mv88e6352_phylink_get_caps().
This is a problem because mv88e6xxx_get_caps(), apart from being
a top-level function (method invoked by dsa_switch_ops), is now also
directly called from mv88e6xxx_setup_port(), which runs under the
mv88e6xxx_reg_lock() taken by mv88e6xxx_setup(). Therefore, when running
on mv88e6352, the reg_lock would be acquired a second time and the
system would deadlock on driver probe.
The things that mv88e6xxx_setup() can compete with in terms of register
access with are the IRQ handlers and MDIO bus operations registered by
mv88e6xxx_probe(). So there is a real need to acquire the register lock.
The register lock can, in principle, be dropped and re-acquired pretty
much at will within the driver, as long as no operations that involve
waiting for indirect access to complete (essentially, callers of
mv88e6xxx_smi_direct_wait() and mv88e6xxx_wait_mask()) are interrupted
with the lock released. However, I would guess that in mv88e6xxx_setup(),
the critical section is kept open for such a long time just in order to
optimize away multiple lock/unlock operations on the registers.
We could, in principle, drop the reg_lock right before the
mv88e6xxx_setup_port() -> mv88e6xxx_get_caps() call, and
re-acquire it immediately afterwards. But this would look ugly, because
mv88e6xxx_setup_port() would release a lock which it didn't acquire, but
the caller did.
A cleaner solution to this issue comes from the observation that struct
mv88e6xxxx_ops methods generally assume they are called with the
reg_lock already acquired. Whereas mv88e6352_phylink_get_caps() is more
the exception rather than the norm, in that it acquires the lock itself.
Let's enforce the same locking pattern/convention for
chip->info->ops->phylink_get_caps() as well, and make
mv88e6xxx_get_caps(), the top-level function, acquire the register lock
explicitly, for this one implementation that will access registers for
port 4 to work properly.
This means that mv88e6xxx_setup_port() will no longer call the top-level
function, but the low-level mv88e6xxx_ops method which expects the
correct calling context (register lock held).
Compared to chip->info->ops->phylink_get_caps(), mv88e6xxx_get_caps()
also fixes up the supported_interfaces bitmap for internal ports, since
that can be done generically and does not require per-switch knowledge.
That's code which will no longer execute, however mv88e6xxx_setup_port()
doesn't need that. It just needs to look at the mac_capabilities bitmap.
Fixes: cc1049ccee ("net: dsa: mv88e6xxx: fix speed setting for CPU/DSA ports")
Reported-by: Maksim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20221214110120.3368472-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e43039a49 ]
There is a memory leaks reported by kmemleak:
unreferenced object 0xffff888116111000 (size 2048):
comm "modprobe", pid 817, jiffies 4294759745 (age 76.502s)
hex dump (first 32 bytes):
00 c4 0a 04 81 88 ff ff 08 10 11 16 81 88 ff ff ................
08 10 11 16 81 88 ff ff 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff815bcd82>] kmalloc_trace+0x22/0x60
[<ffffffff827e20ee>] phy_device_create+0x4e/0x90
[<ffffffff827e6072>] get_phy_device+0xd2/0x220
[<ffffffff827e7844>] mdiobus_scan+0xa4/0x2e0
[<ffffffff827e8be2>] __mdiobus_register+0x482/0x8b0
[<ffffffffa01f5d24>] r6040_init_one+0x714/0xd2c [r6040]
...
The problem occurs in probe process as follows:
r6040_init_one:
mdiobus_register
mdiobus_scan <- alloc and register phy_device,
the reference count of phy_device is 3
r6040_mii_probe
phy_connect <- connect to the first phy_device,
so the reference count of the first
phy_device is 4, others are 3
register_netdev <- fault inject succeeded, goto error handling path
// error handling path
err_out_mdio_unregister:
mdiobus_unregister(lp->mii_bus);
err_out_mdio:
mdiobus_free(lp->mii_bus); <- the reference count of the first
phy_device is 1, it is not released
and other phy_devices are released
// similarly, the remove process also has the same problem
The root cause is traced to the phy_device is not disconnected when
removes one r6040 device in r6040_remove_one() or on error handling path
after r6040_mii probed successfully. In r6040_mii_probe(), a net ethernet
device is connected to the first PHY device of mii_bus, in order to
notify the connected driver when the link status changes, which is the
default behavior of the PHY infrastructure to handle everything.
Therefore the phy_device should be disconnected when removes one r6040
device or on error handling path.
Fix it by adding phy_disconnect() when removes one r6040 device or on
error handling path after r6040_mii probed successfully.
Fixes: 3831861b4a ("r6040: implement phylib")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221213125614.927754-1-lizetao1@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ff8bff704 ]
There is a race resulting in alive SOCK_SEQPACKET socket
may change its state from TCP_ESTABLISHED to TCP_CLOSE:
unix_release_sock(peer) unix_dgram_sendmsg(sk)
sock_orphan(peer)
sock_set_flag(peer, SOCK_DEAD)
sock_alloc_send_pskb()
if !(sk->sk_shutdown & SEND_SHUTDOWN)
OK
if sock_flag(peer, SOCK_DEAD)
sk->sk_state = TCP_CLOSE
sk->sk_shutdown = SHUTDOWN_MASK
After that socket sk remains almost normal: it is able to connect, listen, accept
and recvmsg, while it can't sendmsg.
Since this is the only possibility for alive SOCK_SEQPACKET to change
the state in such way, we should better fix this strange and potentially
danger corner case.
Note, that we will return EPIPE here like this is normally done in sock_alloc_send_pskb().
Originally used ECONNREFUSED looks strange, since it's strange to return
a specific retval in dependence of race in kernel, when user can't affect on this.
Also, move TCP_CLOSE assignment for SOCK_DGRAM sockets under state lock
to fix race with unix_dgram_connect():
unix_dgram_connect(other) unix_dgram_sendmsg(sk)
unix_peer(sk) = NULL
unix_state_unlock(sk)
unix_state_double_lock(sk, other)
sk->sk_state = TCP_ESTABLISHED
unix_peer(sk) = other
unix_state_double_unlock(sk, other)
sk->sk_state = TCP_CLOSED
This patch fixes both of these races.
Fixes: 83301b5367 ("af_unix: Set TCP_ESTABLISHED for datagram sockets too")
Signed-off-by: Kirill Tkhai <tkhai@ya.ru>
Link: https://lore.kernel.org/r/135fda25-22d5-837a-782b-ceee50e19844@ya.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f28157778 ]
Fix a slab-out-of-bounds read that occurs in nla_put() called from
nfc_genl_send_target() when target->sensb_res_len, which is duplicated
from an nfc_target in pn533, is too large as the nfc_target is not
properly initialized and retains garbage values. Clear nfc_targets with
memset() before they are used.
Found by a modified version of syzkaller.
BUG: KASAN: slab-out-of-bounds in nla_put
Call Trace:
memcpy
nla_put
nfc_genl_dump_targets
genl_lock_dumpit
netlink_dump
__netlink_dump_start
genl_family_rcv_msg_dumpit
genl_rcv_msg
netlink_rcv_skb
genl_rcv
netlink_unicast
netlink_sendmsg
sock_sendmsg
____sys_sendmsg
___sys_sendmsg
__sys_sendmsg
do_syscall_64
Fixes: 673088fb42 ("NFC: pn533: Send ATR_REQ directly for active device detection")
Fixes: 361f3cb7f9 ("NFC: DEP link hook implementation for pn533")
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221214015139.119673-1-linuxlovemin@yonsei.ac.kr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 628050ec95 ]
Before enetc_clean_rx_ring_xdp() calls xdp_do_redirect(), each software
BD in the RX ring between index orig_i and i can have one of 2 refcount
values on its page.
We are the owner of the current buffer that is being processed, so the
refcount will be at least 1.
If the current owner of the buffer at the diametrically opposed index
in the RX ring (i.o.w, the other half of this page) has not yet called
kfree(), this page's refcount could even be 2.
enetc_page_reusable() in enetc_flip_rx_buff() tests for the page
refcount against 1, and [ if it's 2 ] does not attempt to reuse it.
But if enetc_flip_rx_buff() is put after the xdp_do_redirect() call,
the page refcount can have one of 3 values. It can also be 0, if there
is no owner of the other page half, and xdp_do_redirect() for this
buffer ran so far that it triggered a flush of the devmap/cpumap bulk
queue, and the consumers of those bulk queues also freed the buffer,
all by the time xdp_do_redirect() returns the execution back to enetc.
This is the reason why enetc_flip_rx_buff() is called before
xdp_do_redirect(), but there is a big flaw with that reasoning:
enetc_flip_rx_buff() will set rx_swbd->page = NULL on both sides of the
enetc_page_reusable() branch, and if xdp_do_redirect() returns an error,
we call enetc_xdp_free(), which does not deal gracefully with that.
In fact, what happens is quite special. The page refcounts start as 1.
enetc_flip_rx_buff() figures they're reusable, transfers these
rx_swbd->page pointers to a different rx_swbd in enetc_reuse_page(), and
bumps the refcount to 2. When xdp_do_redirect() later returns an error,
we call the no-op enetc_xdp_free(), but we still haven't lost the
reference to that page. A copy of it is still at rx_ring->next_to_alloc,
but that has refcount 2 (and there are no concurrent owners of it in
flight, to drop the refcount). What really kills the system is when
we'll flip the rx_swbd->page the second time around. With an updated
refcount of 2, the page will not be reusable and we'll really leak it.
Then enetc_new_page() will have to allocate more pages, which will then
eventually leak again on further errors from xdp_do_redirect().
The problem, summarized, is that we zeroize rx_swbd->page before we're
completely done with it, and this makes it impossible for the error path
to do something with it.
Since the packet is potentially multi-buffer and therefore the
rx_swbd->page is potentially an array, manual passing of the old
pointers between enetc_flip_rx_buff() and enetc_xdp_free() is a bit
difficult.
For the sake of going with a simple solution, we accept the possibility
of racing with xdp_do_redirect(), and we move the flip procedure to
execute only on the redirect success path. By racing, I mean that the
page may be deemed as not reusable by enetc (having a refcount of 0),
but there will be no leak in that case, either.
Once we accept that, we have something better to do with buffers on
XDP_REDIRECT failure. Since we haven't performed half-page flipping yet,
we won't, either (and this way, we can avoid enetc_xdp_free()
completely, which gives the entire page to the slab allocator).
Instead, we'll call enetc_xdp_drop(), which will recycle this half of
the buffer back to the RX ring.
Fixes: 9d2b68cc10 ("net: enetc: add support for XDP_REDIRECT")
Suggested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221213001908.2347046-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73278d4833 ]
The patch adding support for dynamically allocated arrays accidentally
dropped the line setting ctrl->is_new to 1, thus new string values were
always ignored.
Fixes: fb582cba44 ("media: v4l2-ctrls: add support for dynamically allocated arrays.")
Reported-by: Alice Yuan <alice.yuan@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8dfde09c9 ]
BPF selftests require CONFIG_FUNCTION_ERROR_INJECTION to work. However,
CONFIG_FUNCTION_ERROR_INJECTION is no longer 'y' by default after recent
changes. As a result, we are seeing errors like the following from BPF CI:
bpf_testmod_test_read() is not modifiable
__x64_sys_setdomainname is not sleepable
__x64_sys_getpgid is not sleepable
Fix this by explicitly selecting CONFIG_FUNCTION_ERROR_INJECTION in the
selftest config.
Fixes: a4412fdd49 ("error-injection: Add prompt for function error injection")
Reported-by: Daniel Müller <deso@posteo.net>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Müller <deso@posteo.net>
Link: https://lore.kernel.org/bpf/20221213220500.3427947-1-song@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64dc8c732f ]
Our test report a uaf for 'bfqq->bic' in 5.10:
==================================================================
BUG: KASAN: use-after-free in bfq_select_queue+0x378/0xa30
CPU: 6 PID: 2318352 Comm: fsstress Kdump: loaded Not tainted 5.10.0-60.18.0.50.h602.kasan.eulerosv2r11.x86_64 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58-20220320_160524-szxrtosci10000 04/01/2014
Call Trace:
bfq_select_queue+0x378/0xa30
bfq_dispatch_request+0xe8/0x130
blk_mq_do_dispatch_sched+0x62/0xb0
__blk_mq_sched_dispatch_requests+0x215/0x2a0
blk_mq_sched_dispatch_requests+0x8f/0xd0
__blk_mq_run_hw_queue+0x98/0x180
__blk_mq_delay_run_hw_queue+0x22b/0x240
blk_mq_run_hw_queue+0xe3/0x190
blk_mq_sched_insert_requests+0x107/0x200
blk_mq_flush_plug_list+0x26e/0x3c0
blk_finish_plug+0x63/0x90
__iomap_dio_rw+0x7b5/0x910
iomap_dio_rw+0x36/0x80
ext4_dio_read_iter+0x146/0x190 [ext4]
ext4_file_read_iter+0x1e2/0x230 [ext4]
new_sync_read+0x29f/0x400
vfs_read+0x24e/0x2d0
ksys_read+0xd5/0x1b0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Commit 3bc5e683c6 ("bfq: Split shared queues on move between cgroups")
changes that move process to a new cgroup will allocate a new bfqq to
use, however, the old bfqq and new bfqq can point to the same bic:
1) Initial state, two process with io in the same cgroup.
Process 1 Process 2
(BIC1) (BIC2)
| Λ | Λ
| | | |
V | V |
bfqq1 bfqq2
2) bfqq1 is merged to bfqq2.
Process 1 Process 2
(BIC1) (BIC2)
| |
\-------------\|
V
bfqq1 bfqq2(coop)
3) Process 1 exit, then issue new io(denoce IOA) from Process 2.
(BIC2)
| Λ
| |
V |
bfqq2(coop)
4) Before IOA is completed, move Process 2 to another cgroup and issue io.
Process 2
(BIC2)
Λ
|\--------------\
| V
bfqq2 bfqq3
Now that BIC2 points to bfqq3, while bfqq2 and bfqq3 both point to BIC2.
If all the requests are completed, and Process 2 exit, BIC2 will be
freed while there is no guarantee that bfqq2 will be freed before BIC2.
Fix the problem by clearing bfqq->bic while bfqq is detached from bic.
Fixes: 3bc5e683c6 ("bfq: Split shared queues on move between cgroups")
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20221214030430.3304151-1-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1232946cf5 ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
skb_queue_purge() is called under spin_lock_irqsave() in handle_dmsg()
and hfcm_l1callback(), kfree_skb() is called in them, to fix this, use
skb_queue_splice_init() to move the dch->squeue to a free queue, also
enqueue the tx_skb and rx_skb, at last calling __skb_queue_purge() to
free the SKBs afer unlock.
Fixes: af69fb3a8f ("Add mISDN HFC multiport driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0f596bd75 ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
skb_queue_purge() is called under spin_lock_irqsave() in hfcpci_l2l1D(),
kfree_skb() is called in it, to fix this, use skb_queue_splice_init()
to move the dch->squeue to a free queue, also enqueue the tx_skb and
rx_skb, at last calling __skb_queue_purge() to free the SKBs afer unlock.
Fixes: 1700fe1a10 ("Add mISDN HFC PCI driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddc9648db1 ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
skb_queue_purge() is called under spin_lock_irqsave() in hfcusb_l2l1D(),
kfree_skb() is called in it, to fix this, use skb_queue_splice_init()
to move the dch->squeue to a free queue, also enqueue the tx_skb and
rx_skb, at last calling __skb_queue_purge() to free the SKBs afer unlock.
In tx_iso_complete(), dev_kfree_skb() is called to consume the transmitted
SKB, so replace it with dev_consume_skb_irq().
Fixes: 69f52adb2d ("mISDN: Add HFC USB driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e95cc44763 ]
Currently, when a high prio link enslaved, or when current link down,
the high prio port could be selected. But when high prio link up, the
new active slave reselection is not triggered. Fix it by checking link's
prio when getting up. Making the do_failover after looping all slaves as
there may be multi high prio slaves up.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 0a2ff7cc8a ("Bonding: add per-port priority for failover re-selection")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d0b738fc5 ]
There is one direct accesses to bond->curr_active_slave in
bond_miimon_commit(). Protected it by rcu_access_pointer()
since the later of this function also use this one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: e95cc44763 ("bonding: do failover when high prio link up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fb45f95ee ]
The for-loop was broken from the start. It translates to:
for (i = 0; i < 4; i += 4)
which means the loop statement is run only once, so only the highest
32-bit of the IPv6 address gets mangled.
Fix the loop increment.
Fixes: 0e07e25b48 ("netfilter: flowtable: fix NAT IPv6 offload mangling")
Fixes: 5c27d8d76c ("netfilter: nf_flow_table_offload: add IPv6 support")
Signed-off-by: Qingfang DENG <dqfext@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9aafbfa5f5 ]
rtas-error-log-max is not the name of an RTAS function, so rtas_token()
is not the appropriate API for retrieving its value. We already have
rtas_get_error_log_max() which returns a sensible value if the property
is absent for any reason, so use that instead.
Fixes: 8d633291b4 ("powerpc/eeh: pseries platform EEH error log retrieval")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
[mpe: Drop no-longer possible error handling as noticed by ajd]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221118150751.469393-6-nathanl@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa3c668f2f ]
According to MT7622 Reference Manual for Development Board v1.0 the PWM
unit found in the MT7622 SoC also comes with the PWM_CK_26M_SEL register
at offset 0x210 just like other modern MediaTek ARM64 SoCs.
And also MT7622 sets that register to 0x00000001 on reset which is
described as 'Select 26M fix CLK as BCLK' in the datasheet.
Hence set has_ck_26m_sel to true also for MT7622 which results in the
driver writing 0 to the PWM_CK_26M_SEL register which is described as
'Select bus CLK as BCLK'.
Fixes: 0c0ead7623 ("pwm: mediatek: Always use bus clock")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/Y1iF2slvSblf6bYK@makrotopia.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef5bb8e7a7 ]
This driver treats IOMMU_DOMAIN_IDENTITY the same as UNMANAGED, which
cannot possibly be correct.
UNMANAGED domains are required to start out blocking all DMAs. This seems
to be what this driver does as it allocates a first level 'dt' for the IO
page table that is 0 filled.
Thus UNMANAGED looks like a working IO page table, and so IDENTITY must be
a mistake. Remove it.
Fixes: 4100b8c229 ("iommu: Add Allwinner H6 IOMMU driver")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/0-v1-97f0adf27b5e+1f0-s50_identity_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef693a8440 ]
Fix the smatch warnings:
drivers/iommu/mtk_iommu.c:878 mtk_iommu_mm_dts_parse() error: uninitialized
symbol 'larbnode'.
If someone abuse the dtsi node(Don't follow the definition of dt-binding),
for example "mediatek,larbs" is provided as boolean property, "larb_nr"
will be zero and cause abnormal.
To fix this problem and improve the code safety, add some checking
for the invalid input from dtsi, e.g. checking the larb_nr/larbid valid
range, and avoid "mediatek,larb-id" property conflicts in the smi-larb
nodes.
Fixes: d2e9a1102c ("iommu/mediatek: Contain MM IOMMU flow with the MM TYPE")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20221018024258.19073-5-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2659392856 ]
The mtk_iommu_mm_dts_parse will parse the smi larbs nodes. if the i+1
larb is parsed fail, we should put_device for the i..0 larbs.
There are two places need to comment:
1) The larbid may be not linear mapping, we should loop whole
the array in the error path.
2) I move this line position: "data->larb_imu[id].dev = &plarbdev->dev;"
before "if (!plarbdev->dev.driver)", That means set
data->larb_imu[id].dev before the error path. then we don't need
"platform_device_put(plarbdev)" again in probe_defer case. All depend
on "put_device" of the error path in error cases.
Fixes: d2e9a1102c ("iommu/mediatek: Contain MM IOMMU flow with the MM TYPE")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20221018024258.19073-4-yong.wu@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f4ab7da90 ]
In check_all_cpu_dscr_defaults, opendir() opens the directory stream.
Add missing closedir() in the error path to release it.
In check_cpu_dscr_default, open() creates an open file descriptor.
Add missing close() in the error path to release it.
Fixes: ebd5858c90 ("selftests/powerpc: Add test for all DSCR sysfs interfaces")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221205084429.570654-1-linmq006@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03f7c1d2a4 ]
Based on getPerfCountInfo v1.018 documentation, some of the
hv_gpci events were deprecated for platform firmware that
supports counter_info_version 0x8 or above.
Fix the hv_gpci event list by adding a new attribute group
called "hv_gpci_event_attrs_v6" and a "ENABLE_EVENTS_COUNTERINFO_V6"
macro to enable these events for platform firmware
that supports counter_info_version 0x6 or below. And assigning
the hv_gpci event list based on output counter info version
of underlying plaform.
Fixes: 97bf264018 ("powerpc/perf/hv-gpci: add the remaining gpci requests")
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221130174513.87501-1-kjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32c5209214 ]
The interrupt frame detection and loads from the hypothetical pt_regs
are not bounds-checked. The next-frame validation only bounds-checks
STACK_FRAME_OVERHEAD, which does not include the pt_regs. Add another
test for this.
The user could set r1 to be equal to the address matching the first
interrupt frame - STACK_INT_FRAME_SIZE, which is in the previous page
due to the kernel redzone, and induce the kernel to load the marker from
there. Possibly this could cause a crash at least. If the user could
induce the previous page to contain a valid marker, then it might be
able to direct perf to read specific memory addresses in a way that
could be transmitted back to the user in the perf data.
Fixes: 20002ded4d ("perf_counter: powerpc: Add callchain support")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20221127124942.1665522-4-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c76ef3f26 ]
In kill_kprobe(), the check whether disarm_kprobe_ftrace() needs to be
called always fails. This is because before that we set the
KPROBE_FLAG_GONE flag for kprobe so that "!kprobe_disabled(p)" is always
false.
The disarm_kprobe_ftrace() call introduced by commit:
0cb2f1372b ("kprobes: Fix NULL pointer dereference at kprobe_ftrace_handler")
to fix the NULL pointer reference problem. When the probe is enabled, if
we do not disarm it, this problem still exists.
Fix it by putting the probe enabled check before setting the
KPROBE_FLAG_GONE flag.
Link: https://lore.kernel.org/all/20221126114316.201857-1-lihuafei1@huawei.com/
Fixes: 3031313eb3 ("kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()")
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
