[ Upstream commit bdc2ab5c61 ]
In rds_message_map_pages, the rm is freed by rds_message_put(rm).
But rm is still used by rm->data.op_sg in return value.
My patch assigns ERR_CAST(rm->data.op_sg) to err before the rm is
freed to avoid the uaf.
Fixes: 7dba92037b ("net/rds: Use ERR_PTR for rds_message_alloc_sgs()")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b76002ae ]
Calculating the number of compeltion EQs based on the number of
available IRQ vectors doesn't work now that all async EQs share one IRQ.
Thus the max number of EQs can be exceeded on systems with more than
approximately 256 CPUs. Take this into account when calculating the
number of available completion EQs.
Fixes: 81bfa20603 ("net/mlx5: Use a single IRQ for all async EQs")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3211434dfe ]
Use connector_type read from PTYS register when it's valid, based on
corresponding capability bit.
Fixes: 5b4793f817 ("net/mlx5e: Add support for reading connector type from PTYS")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c0d6e4820 ]
card->owner is a required property and since commit 81033c6b58 ("ALSA:
core: Warn on empty module") a warning is issued if it is empty. Add it.
This fixes following warning observed on Lamobo R1:
WARNING: CPU: 1 PID: 190 at sound/core/init.c:207 snd_card_new+0x430/0x480 [snd]
Modules linked in: sun4i_codec(E+) sun4i_backend(E+) snd_soc_core(E) ...
CPU: 1 PID: 190 Comm: systemd-udevd Tainted: G C E 5.10.0-1-armmp #1 Debian 5.10.4-1
Hardware name: Allwinner sun7i (A20) Family
Call trace:
(snd_card_new [snd])
(snd_soc_bind_card [snd_soc_core])
(snd_soc_register_card [snd_soc_core])
(sun4i_codec_probe [sun4i_codec])
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on early Allwinner SoCs")
Related: commit 3c27ea23ff ("ASoC: qcom: Set card->owner to avoid warnings")
Related: commit ec653df2a0 ("drm/vc4/vc4_hdmi: fill ASoC card owner")
Cc: linux-arm-kernel@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Signed-off-by: Bastian Germann <bage@linutronix.de>
Link: https://lore.kernel.org/r/20210331151843.30583-1-bage@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c056d480b4 ]
We should not be advertising EEE for modes that we do not support,
correct that oversight by looking at the PHY device supported linkmodes.
Fixes: 99cec8a4dd ("net: phy: broadcom: Allow enabling or disabling of EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ea538dbee ]
A merge hint message needs some time to process before the merged
flow actually reaches the firmware, during which we may get duplicate
merge hints if there're more than one packet that hit the pre-merged
flow. And processing duplicate merge hints will cost extra host_ctx's
which are a limited resource.
Avoid the duplicate merge by using hash table to store the sub_flows
to be merged.
Fixes: 8af56f40e5 ("nfp: flower: offload merge flows")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03cb4d05b4 ]
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.
Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared. After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.
If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.
Fixes: 0795fb2021 ("net/ncsi: Stop monitor if channel times out or is inactive")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f57011e72f ]
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bf24dc0cc ]
In the if(skb_peek(arrvq) == skb) branch, it calls __skb_dequeue(arrvq) to get
the skb by skb = skb_peek(arrvq). Then __skb_dequeue() unlinks the skb from arrvq
and returns the skb which equals to skb_peek(arrvq). After __skb_dequeue(arrvq)
finished, the skb is freed by kfree_skb(__skb_dequeue(arrvq)) in the first time.
Unfortunately, the same skb is freed in the second time by kfree_skb(skb) after
the branch completed.
My patch removes kfree_skb() in the if(skb_peek(arrvq) == skb) branch, because
this skb will be freed by kfree_skb(skb) finally.
Fixes: cb1b728096 ("tipc: eliminate race condition at multicast reception")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bfb3dea96 ]
Accessing SGE_QBASE_MAP[0-3] and SGE_QBASE_INDEX registers can lead
to SGE missing doorbells under heavy traffic. So, only collect them
when adapter is idle. Also update the regdump range to skip collecting
these registers.
Fixes: 80a95a80d3 ("cxgb4: collect SGE PF/VF queue map")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cfad4f458 ]
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: c1c9d41319 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Fixes: 748f908cc8 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d751350826 ]
Based on the IOMMU configuration, the current cache control settings can
result in possible coherency issues. The hardware team has recommended
new settings for the PCI device path to eliminate the issue.
Fixes: 6f595959c0 ("amd-xgbe: Adjust register settings to improve performance")
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f6c411c9b ]
1) argument should not be freed in any case - the caller already has
it as ->s_fs_info (and uses it a lot afterwards)
2) allocate readlink buffer with kmalloc() - the caller has no way
to tell if it's got that (on absolute symlink) or a result of
kasprintf(). Sure, for SLAB and SLUB kfree() works on results of
kmem_cache_alloc(), but that's not documented anywhere, might change
in the future *and* is already not true for SLOB.
Fixes: 52b209f7b8 ("get rid of hostfs_read_inode()")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b58c4e9619 ]
Improve readability and maintainability by replacing a hardcoded string
allocation and formatting by the use of the kasprintf() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 347b5650cd ]
Fix the reason of kernel oops when i40e driver removed VFs.
Added new __I40E_VFS_RELEASING state to signalize releasing
process by PF, that it makes possible to exit of reset VF procedure.
Without this patch, it is possible to suspend the VFs reset by
releasing VFs resources procedure. Retrying the reset after the
timeout works on the freed VF memory causing a kernel oops.
Fixes: d43d60e5eb ("i40e: ensure reset occurs when disabling VF")
Signed-off-by: Eryk Rybak <eryk.roch.rybak@intel.com>
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1e3a56070 ]
When xfrm interfaces are used in combination with namespaces
and ESP offload, we get a dst_entry NULL pointer dereference.
This is because we don't have a dst_entry attached in the ESP
offloading case and we need to do a policy lookup before the
namespace transition.
Fix this by expicit checking of skb_dst(skb) before accessing it.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b82e75c1 ]
The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.
>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.
So search available sysclk_divs from 2 to 1 other than from 1 to 2.
Fixes: 84fdc00d51 ("ASoC: codec: wm9860: Refactor PLL out freq search")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 154deab6a3 ]
Now in esp4/6_gso_segment(), before calling inner proto .gso_segment,
NETIF_F_CSUM_MASK bits are deleted, as HW won't be able to do the
csum for inner proto due to the packet encrypted already.
So the UDP/TCP packet has to do the checksum on its own .gso_segment.
But SCTP is using CRC checksum, and for that NETIF_F_SCTP_CRC should
be deleted to make SCTP do the csum in own .gso_segment as well.
In Xiumei's testing with SCTP over IPsec/veth, the packets are kept
dropping due to the wrong CRC checksum.
Reported-by: Xiumei Mu <xmu@redhat.com>
Fixes: 7862b4058b ("esp: Add gso handlers for esp4 and esp6")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e88add19f6 ]
A sequence counter write section must be serialized or its internal
state can get corrupted. The "xfrm_state_hash_generation" seqcount is
global, but its write serialization lock (net->xfrm.xfrm_state_lock) is
instantiated per network namespace. The write protection is thus
insufficient.
To provide full protection, localize the sequence counter per network
namespace instead. This should be safe as both the seqcount read and
write sections access data exclusively within the network namespace. It
also lays the foundation for transforming "xfrm_state_hash_generation"
data type from seqcount_t to seqcount_LOCKNAME_t in further commits.
Fixes: b65e3d7be0 ("xfrm: state: add sequence count to detect hash resizes")
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b6e7088af ]
According to Table 30 ("DVFS_MoniVDAC [6:0] Setting Table") in the
BD9571MWV-M Datasheet Rev. 002, the valid voltage range is 600..1100 mV
(settings 0x3c..0x6e). While the lower limit is taken into account (by
setting regulator_desc.linear_min_sel to 0x3c), the upper limit is not.
Fix this by reducing regulator_desc.n_voltages from 0x80 to 0x6f.
Fixes: e85c5a153f ("regulator: Add ROHM BD9571MWV-M PMIC regulator driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210312130242.3390038-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fc0e3b6a8 ]
Frag needed should only be sent if the header enables DF.
This fix allows packets larger than MTU to pass the xfrm interface
and be fragmented after encapsulation, aligning behavior with
non-interface xfrm.
Fixes: f203b76d78 ("xfrm: Add virtual xfrm interfaces")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4b5923249b upstream.
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Updated after the upstream commit 3e9005be87 required some changes
for Linux 5.4 ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e9005be87 upstream.
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Move gswip_port_set_{speed, duplex, pause} calls from
gswip_phylink_mac_link_up to gswip_phylink_mac_config because the
data required for these functions is not available inside
gswip_phylink_mac_link_up yet in Linux 5.4 (it was only added with
Linux 5.7). ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9adc89af72 upstream.
Currently the mentioned helper can end-up freeing the socket wmem
without waking-up any processes waiting for more write memory.
If the partially orphaned skb is attached to an UDP (or raw) socket,
the lack of wake-up can hang the user-space.
Even for TCP sockets not calling the sk destructor could have bad
effects on TSQ.
Address the issue using skb_orphan to release the sk wmem before
setting the new sock_efree destructor. Additionally bundle the
whole ownership update in a new helper, so that later other
potential users could avoid duplicate code.
v1 -> v2:
- use skb_orphan() instead of sort of open coding it (Eric)
- provide an helper for the ownership change (Eric)
Fixes: f6ba8d33cf ("netem: fix skb_orphan_partial()")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 630e4576f8 upstream.
Found by virtue of ipv6 raw sockets not honouring the per-socket
IP{,V6}_FREEBIND setting.
Based on hits found via:
git grep '[.]ip_nonlocal_bind'
We fix both raw ipv6 sockets to honour IP{,V6}_FREEBIND and IP{,V6}_TRANSPARENT,
and we fix sctp sockets to honour IP{,V6}_TRANSPARENT (they already honoured
FREEBIND), and not just the ipv6 'ip_nonlocal_bind' sysctl.
The helper is defined as:
static inline bool ipv6_can_nonlocal_bind(struct net *net, struct inet_sock *inet) {
return net->ipv6.sysctl.ip_nonlocal_bind || inet->freebind || inet->transparent;
}
so this change only widens the accepted opt-outs and is thus a clean bugfix.
I'm not entirely sure what 'fixes' tag to add, since this is AFAICT an ancient bug,
but IMHO this should be applied to stable kernels as far back as possible.
As such I'm adding a 'fixes' tag with the commit that originally added the helper,
which happened in 4.19. Backporting to older LTS kernels (at least 4.9 and 4.14)
would presumably require open-coding it or backporting the helper as well.
Other possibly relevant commits:
v4.18-rc6-1502-g83ba4645152d net: add helpers checking if socket can be bound to nonlocal address
v4.18-rc6-1431-gd0c1f01138c4 net/ipv6: allow any source address for sendmsg pktinfo with ip_nonlocal_bind
v4.14-rc5-271-gb71d21c274ef sctp: full support for ipv6 ip_nonlocal_bind & IP_FREEBIND
v4.7-rc7-1883-g9b9742022888 sctp: support ipv6 nonlocal bind
v4.1-12247-g35a256fee52c ipv6: Nonlocal bind
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 83ba464515 ("net: add helpers checking if socket can be bound to nonlocal address")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d6803921a upstream.
Reset MAC header in HSR Tx path. This is needed, because direct packet
transmission, e.g. by specifying PACKET_QDISC_BYPASS does not reset the MAC
header.
This has been observed using the following setup:
|$ ip link add name hsr0 type hsr slave1 lan0 slave2 lan1 supervision 45 version 1
|$ ifconfig hsr0 up
|$ ./test hsr0
The test binary is using mmap'ed sockets and is specifying the
PACKET_QDISC_BYPASS socket option.
This patch resolves the following warning on a non-patched kernel:
|[ 112.725394] ------------[ cut here ]------------
|[ 112.731418] WARNING: CPU: 1 PID: 257 at net/hsr/hsr_forward.c:560 hsr_forward_skb+0x484/0x568
|[ 112.739962] net/hsr/hsr_forward.c:560: Malformed frame (port_src hsr0)
The warning can be safely removed, because the other call sites of
hsr_forward_skb() make sure that the skb is prepared correctly.
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1153a74768 upstream.
Normally, TXQs have
txq->tid = tid;
txq->ac = ieee80211_ac_from_tid(tid);
However, the special management TXQ actually has
txq->tid = IEEE80211_NUM_TIDS; // 16
txq->ac = IEEE80211_AC_VO;
This makes sense, but ieee80211_ac_from_tid(16) is the same
as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE.
Now, normally this is fine. However, if the netdev queues
were stopped, then the code in ieee80211_tx_dequeue() will
propagate the stop from the interface (vif->txqs_stopped[])
if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as
stopped. On wake, however, __ieee80211_wake_txqs() will wake
the TXQ if AC 0 (txq->ac) is woken up.
If a driver stops all queues with ieee80211_stop_tx_queues()
and then wakes them again with ieee80211_wake_tx_queues(),
the ieee80211_wake_txqs() tasklet will run to resync queue
and TXQ state. If all queues were woken, then what'll happen
is that _ieee80211_wake_txqs() will run in order of HW queues
0-3, typically (and certainly for iwlwifi) corresponding to
ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in
order 0-3.
When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll
wake up the management TXQ (remember its tid is 16), and the
driver's wake_tx_queue() will be called. That tries to get a
frame, which will immediately *stop* the TXQ again, because
now we check against AC 2, and AC 2 hasn't yet been marked as
woken up again in sdata->vif.txqs_stopped[] since we're only
in the __ieee80211_wake_txqs() call for AC 0.
Thus, the management TXQ will never be started again.
Fix this by checking txq->ac directly instead of calculating
the AC as ieee80211_ac_from_tid(txq->tid).
Fixes: adf8ed01e4 ("mac80211: add an optional TXQ for other PS-buffered frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b5674fe6b upstream.
Remove vsi->netdev->name from the trace.
This is redundant information. With the devinfo trace, the adapter
is already identifiable.
Previously following error was produced when compiling against sparse.
i40e_main.c:2571 i40e_sync_vsi_filters() error:
we previously assumed 'vsi->netdev' could be null (see line 2323)
Fixes: b603f9dc20 ("i40e: Log info when PF is entering and leaving Allmulti mode.")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61431a5907 upstream.
Commit 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
added a call to dev_parse_header_protocol() but mac_header is not yet set.
This means that eth_hdr() reads complete garbage, and syzbot complained about it [1]
This patch resets mac_header earlier, to get more coverage about this change.
Audit of virtio_net_hdr_to_skb() callers shows that this change should be safe.
[1]
BUG: KASAN: use-after-free in eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
Read of size 2 at addr ffff888017a6200b by task syz-executor313/8409
CPU: 1 PID: 8409 Comm: syz-executor313 Not tainted 5.12.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
eth_header_parse_protocol+0xdc/0xe0 net/ethernet/eth.c:282
dev_parse_header_protocol include/linux/netdevice.h:3177 [inline]
virtio_net_hdr_to_skb.constprop.0+0x99d/0xcd0 include/linux/virtio_net.h:83
packet_snd net/packet/af_packet.c:2994 [inline]
packet_sendmsg+0x2325/0x52b0 net/packet/af_packet.c:3031
sock_sendmsg_nosec net/socket.c:654 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:674
sock_no_sendpage+0xf3/0x130 net/core/sock.c:2860
kernel_sendpage.part.0+0x1ab/0x350 net/socket.c:3631
kernel_sendpage net/socket.c:3628 [inline]
sock_sendpage+0xe5/0x140 net/socket.c:947
pipe_to_sendpage+0x2ad/0x380 fs/splice.c:364
splice_from_pipe_feed fs/splice.c:418 [inline]
__splice_from_pipe+0x43e/0x8a0 fs/splice.c:562
splice_from_pipe fs/splice.c:597 [inline]
generic_splice_sendpage+0xd4/0x140 fs/splice.c:746
do_splice_from fs/splice.c:767 [inline]
do_splice+0xb7e/0x1940 fs/splice.c:1079
__do_splice+0x134/0x250 fs/splice.c:1144
__do_sys_splice fs/splice.c:1350 [inline]
__se_sys_splice fs/splice.c:1332 [inline]
__x64_sys_splice+0x198/0x250 fs/splice.c:1332
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
Fixes: 924a9bc362 ("net: check if protocol extracted by virtio_net_hdr_set_proto is correct")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Balazs Nemeth <bnemeth@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c84b33101 upstream.
In '4da6a196f93b1' we fixed a potential unhash loop caused when
a TLS socket in a sockmap was removed from the sockmap. This
happened because the unhash operation on the TLS ctx continued
to point at the sockmap implementation of unhash even though the
psock has already been removed. The sockmap unhash handler when a
psock is removed does the following,
void sock_map_unhash(struct sock *sk)
{
void (*saved_unhash)(struct sock *sk);
struct sk_psock *psock;
rcu_read_lock();
psock = sk_psock(sk);
if (unlikely(!psock)) {
rcu_read_unlock();
if (sk->sk_prot->unhash)
sk->sk_prot->unhash(sk);
return;
}
[...]
}
The unlikely() case is there to handle the case where psock is detached
but the proto ops have not been updated yet. But, in the above case
with TLS and removed psock we never fixed sk_prot->unhash() and unhash()
points back to sock_map_unhash resulting in a loop. To fix this we added
this bit of code,
static inline void sk_psock_restore_proto(struct sock *sk,
struct sk_psock *psock)
{
sk->sk_prot->unhash = psock->saved_unhash;
This will set the sk_prot->unhash back to its saved value. This is the
correct callback for a TLS socket that has been removed from the sock_map.
Unfortunately, this also overwrites the unhash pointer for all psocks.
We effectively break sockmap unhash handling for any future socks.
Omitting the unhash operation will leave stale entries in the map if
a socket transition through unhash, but does not do close() op.
To fix set unhash correctly before calling into tls_update. This way the
TLS enabled socket will point to the saved unhash() handler.
Fixes: 4da6a196f9 ("bpf: Sockmap/tls, during free we may call tcp_bpf_unhash() in loop")
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/161731441904.68884.15593917809745631972.stgit@john-XPS-13-9370
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e5a03bcba upstream.
In nfp_bpf_ctrl_msg_rx, if
nfp_ccm_get_type(skb) == NFP_CCM_TYPE_BPF_BPF_EVENT is true, the skb
will be freed. But the skb is still used by nfp_ccm_rx(&bpf->ccm, skb).
My patch adds a return when the skb was freed.
Fixes: bcf0cafab4 ("nfp: split out common control message handling code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a12f88361 upstream.
Multiple ttys try to claim the same the minor number causing a double
unregistration of the same device. The first unregistration succeeds
but the next one results in a null-ptr-deref.
The get_free_serial_index() function returns an available minor number
but doesn't assign it immediately. The assignment is done by the caller
later. But before this assignment, calls to get_free_serial_index()
would return the same minor number.
Fix this by modifying get_free_serial_index to assign the minor number
immediately after one is found to be and rename it to obtain_minor()
to better reflect what it does. Similary, rename set_serial_by_index()
to release_minor() and modify it to free up the minor number of the
given hso_serial. Every obtain_minor() should have corresponding
release_minor() call.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Reported-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Tested-by: syzbot+c49fe6089f295a05e6f8@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7eeb52721 upstream.
When ice_remove_vsi_lkup_fltr is called, by calling
ice_add_to_vsi_fltr_list local copy of vsi filter list
is created. If any issues during creation of vsi filter
list occurs it up for the caller to free already
allocated memory. This patch ensures proper memory
deallocation in these cases.
Fixes: 80d144c9ac ("ice: Refactor switch rule management structures and functions")
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
