commit f94c0b6658 upstream.
If a device in a RAID4/5/6 is being replaced while another is being
recovered, then the writes to the replacement device currently don't
happen, resulting in corruption when the replacement completes and the
new drive takes over.
This is because the replacement writes are only triggered when
's.replacing' is set and not when the similar 's.sync' is set (which
is the case during resync and recovery - it means all devices need to
be read).
So schedule those writes when s.replacing is set as well.
In this case we cannot use "STRIPE_INSYNC" to record that the
replacement has happened as that is needed for recording that any
parity calculation is complete. So introduce STRIPE_REPLACED to
record if the replacement has happened.
For safety we should also check that STRIPE_COMPUTE_RUN is not set.
This has a similar effect to the "s.locked == 0" test. The latter
ensure that now IO has been flagged but not started. The former
checks if any parity calculation has been flagged by not started.
We must wait for both of these to complete before triggering the
'replace'.
Add a similar test to the subsequent check for "are we finished yet".
This possibly isn't needed (is subsumed in the STRIPE_INSYNC test),
but it makes it more obvious that the REPLACE will happen before we
think we are finished.
Finally if a NeedReplace device is not UPTODATE then that is an
error. We really must trigger a warning.
This bug was introduced in commit 9a3e1101b8
(md/raid5: detect and handle replacements during recovery.)
which introduced replacement for raid5.
That was in 3.3-rc3, so any stable kernel since then would benefit
from this fix.
Reported-by: qindehua <13691222965@163.com>
Tested-by: qindehua <qindehua@163.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30bc9b5387 upstream.
Recent change to use bio_copy_data() in raid1 when repairing
an array is faulty.
The underlying may have changed the bio in various ways using
bio_advance and these need to be undone not just for the 'sbio' which
is being copied to, but also the 'pbio' (primary) which is being
copied from.
So perform the reset on all bios that were read from and do it early.
This also ensure that the sbio->bi_io_vec[j].bv_len passed to
memcmp is correct.
This fixes a crash during a 'check' of a RAID1 array. The crash was
introduced in 3.10 so this is suitable for 3.10-stable.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5024c29831 upstream.
commit 7ceb17e87b
md: Allow devices to be re-added to a read-only array.
allowed a bit more than just that. It also allows devices to be added
to a read-write array and to end up skipping recovery.
This patch removes the offending piece of code pending a rewrite for a
subsequent release.
More specifically:
If the array has a bitmap, then the device will still need a bitmap
based resync ('saved_raid_disk' is set under different conditions
is a bitmap is present).
If the array doesn't have a bitmap, then this is correct as long as
nothing has been written to the array since the metadata was checked
by ->validate_super. However there is no locking to ensure that there
was no write.
Bug was introduced in 3.10 and causes data corruption so
patch is suitable for 3.10-stable.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
based on 4df05f3619 upstream.
Since the IDT is referenced from a fixmap, make sure it is page aligned.
This avoids the risk of the IDT ever being moved in the bss and having
the mapping be offset, resulting in calling incorrect handlers. In the
current upstream kernel this is not a manifested bug, but heavily patched
kernels (such as those using the PaX patch series) did encounter this bug.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: PaX Team <pageexec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ff560fd48 upstream.
There are CPUs which have errata causing RDMSR of a nonexistent MSR to
not fault. We would then try to WRMSR to restore the value of that
MSR, causing a crash. Specifically, some Pentium M variants would
have this problem trying to save and restore the non-existent EFER,
causing a crash on resume.
Work around this by making sure we can write back the result at
suspend time.
Huge thanks to Christian Sünkenberg for finding the offending erratum
that finally deciphered the mystery.
Reported-and-tested-by: Johan Heinrich <onny@project-insanity.org>
Debugged-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/51DDC972.3010005@student.kit.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 604c499cbb upstream.
We need to make sure that the device is not RO or that
the request is not past the number of sectors we want to
issue the DISCARD operation for.
This fixes CVE-2013-2140.
Acked-by: Jan Beulich <JBeulich@suse.com>
Acked-by: Ian Campbell <Ian.Campbell@citrix.com>
[v1: Made it pr_warn instead of pr_debug]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 093b9c71b6 upstream.
Due to commit 3683243b ("xen-netfront: use __pskb_pull_tail to ensure
linear area is big enough on RX") xennet_fill_frags() may end up
filling MAX_SKB_FRAGS + 1 fragments in a receive skb, and only reduce
the fragment count subsequently via __pskb_pull_tail(). That's a
result of xennet_get_responses() allowing a maximum of one more slot to
be consumed (and intermediately transformed into a fragment) if the
head slot has a size less than or equal to RX_COPY_THRESHOLD.
Hence we need to adjust xennet_fill_frags() to pull earlier if we
reached the maximum fragment count - due to the described behavior of
xennet_get_responses() this guarantees that at least the first fragment
will get completely consumed, and hence the fragment count reduced.
In order to not needlessly call __pskb_pull_tail() twice, make the
original call conditional upon the pull target not having been reached
yet, and defer the newly added one as much as possible (an alternative
would have been to always call the function right before the call to
xennet_fill_frags(), but that would imply more frequent cases of
needing to call it twice).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d29a9f629e upstream.
If we stop dropping a root for whatever reason we need to add it back to the
dead root list so that we will re-start the dropping next transaction commit.
The other case this happens is if we recover a drop because we will add a root
without adding it to the fs radix tree, so we can leak it's root and commit root
extent buffer, adding this to the dead root list makes this cleanup happen.
Thanks,
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fec386ac14 upstream.
We aren't setting path->locks[level] when we resume a snapshot deletion which
means we won't unlock the buffer when we free the path. This causes deadlocks
if we happen to re-allocate the block before we've evicted the extent buffer
from cache. Thanks,
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 115930cb2d upstream.
Miao Xie reported the following issue:
The filesystem was corrupted after we did a device replace.
Steps to reproduce:
# mkfs.btrfs -f -m single -d raid10 <device0>..<device3>
# mount <device0> <mnt>
# btrfs replace start -rfB 1 <device4> <mnt>
# umount <mnt>
# btrfsck <device4>
The reason for the issue is that we changed the write offset by mistake,
introduced by commit 625f1c8dc.
We read the data from the source device at first, and then write the
data into the corresponding place of the new device. In order to
implement the "-r" option, the source location is remapped using
btrfs_map_block(). The read takes place on the mapped location, and
the write needs to take place on the unmapped location. Currently
the write is using the mapped location, and this commit changes it
back by undoing the change to the write address that the aforementioned
commit added by mistake.
Reported-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72bb99cfe9 upstream.
In the situation that a writer fails to copy data from userspace it will reset
the write offset to the value it had before it went to sleep. This discarding
any messages written while aquiring the mutex.
Therefore the reset offset needs to be retrieved after acquiring the mutex.
Cc: Android Kernel Team <kernel-team@android.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69acbaac30 upstream.
Comedi devices can do blocking read() or write() (or poll()) if an
asynchronous command has been set up, blocking for data (for read()) or
buffer space (for write()). Various events associated with the
asynchronous command will wake up the blocked reader or writer (or
poller). It is also possible to force the asynchronous command to
terminate by issuing a `COMEDI_CANCEL` ioctl. That shuts down the
asynchronous command, but does not currently wake up the blocked reader
or writer (or poller). If the blocked task could be woken up, it would
see that the command is no longer active and return. The caller of the
`COMEDI_CANCEL` ioctl could attempt to wake up the blocked task by
sending a signal, but that's a nasty workaround.
Change `do_cancel_ioctl()` to wake up the wait queue after it returns
from `do_cancel()`. `do_cancel()` can propagate an error return value
from the low-level comedi driver's cancel routine, but it always shuts
the command down regardless, so `do_cancel_ioctl()` can wake up he wait
queue regardless of the return value from `do_cancel()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b18f08be0 upstream.
`do_cmd_ioctl()` is called with the comedi device's mutex locked to
process the `COMEDI_CMD` ioctl to set up comedi's asynchronous command
handling on a comedi subdevice. `comedi_read()` and `comedi_write()`
are the `read` and `write` handlers for the comedi device, but do not
lock the mutex (for performance reasons, as some things can hold the
mutex for quite a long time).
There is a race condition if `comedi_read()` or `comedi_write()` is
running at the same time and for the same file object and comedi
subdevice as `do_cmd_ioctl()`. `do_cmd_ioctl()` sets the subdevice's
`busy` pointer to the file object way before it sets the `SRF_RUNNING` flag
in the subdevice's `runflags` member. `comedi_read() and
`comedi_write()` check the subdevice's `busy` pointer is pointing to the
current file object, then if the `SRF_RUNNING` flag is not set, will call
`do_become_nonbusy()` to shut down the asyncronous command. Bad things
can happen if the asynchronous command is being shutdown and set up at
the same time.
To prevent the race, don't set the `busy` pointer until
after the `SRF_RUNNING` flag has been set. Also, make sure the mutex is
held in `comedi_read()` and `comedi_write()` while calling
`do_become_nonbusy()` in order to avoid moving the race condition to a
point within that function.
Change some error handling `goto cleanup` statements in `do_cmd_ioctl()`
to simple `return -ERRFOO` statements as a result of changing when the
`busy` pointer is set.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e583d9db99 upstream.
The hub driver was recently changed to use "global" suspend for system
suspend transitions on non-SuperSpeed buses. This means that we don't
suspend devices individually by setting the suspend feature on the
upstream hub port; instead devices all go into suspend automatically
when the root hub stops transmitting packets. The idea was to save
time and to avoid certain kinds of wakeup races.
Now it turns out that many hubs are buggy; they don't relay wakeup
requests from a downstream port to their upstream port if the
downstream port's suspend feature is not set (depending on the speed
of the downstream port, whether or not the hub is enabled for remote
wakeup, and possibly other factors).
We can't have hubs dropping wakeup requests. Therefore this patch
goes partway back to the old policy: It sets the suspend feature for a
port if the device attached to that port or any of its descendants is
enabled for wakeup. People will still be able to benefit from the
time savings if they don't care about wakeup and leave it disabled on
all their devices.
In order to accomplish this, the patch adds a new field to the usb_hub
structure: wakeup_enabled_descendants is a count of how many devices
below a suspended hub are enabled for remote wakeup. A corresponding
new subroutine determines the number of wakeup-enabled devices at or
below an arbitrary suspended USB device.
This should be applied to the 3.10 stable kernel.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c7b871b91 upstream.
Control transfers have both IN and OUT (or SETUP) packets, so when
clearing TT buffers for a control transfer it's necessary to send
two HUB_CLEAR_TT_BUFFER requests to the hub.
Signed-off-by: William Gulland <wgulland@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fad56424f upstream.
The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.
Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: Anders Hammarquist <iko@iko.pp.se>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdcedd6981 upstream.
In case we fail our ->udc_start() callback, we
should be ready to accept another modprobe following
the failed one.
We had forgotten to clear dwc->gadget_driver back
to NULL and, because of that, we were preventing
gadget driver modprobe from being retried.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1974d494de upstream.
Per dwc3 2.50a spec, the is_devspec bit is used to distinguish the
Device Endpoint-Specific Event or Device-Specific Event (DEVT). If the
bit is 1, the event is represented Device-Specific Event, then use
[7:1] bits as Device Specific Event to marked the type. It has 7 bits,
and we can see the reserved8_31 variable name which means from 8 to 31
bits marked reserved, actually there are 24 bits not 25 bits between
that. And 1 + 7 + 24 = 32, the event size is 4 byes.
So in dwc3_event_type, the bit mask should be:
is_devspec [0] 1 bit
type [7:1] 7 bits
reserved8_31 [31:8] 24 bits
This patch should be backported to kernels as old as 3.2, that contain
the commit 72246da40f "usb: Introduce
DesignWare USB3 DRD Driver".
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 315955d707 upstream.
When there is an error with the usb3_phy probe or absence, the error returned
is erroneously for usb2_phy.
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47a64a13d5 upstream.
Set the ehci->resuming flag for the port we receive a remote
wakeup on so that resume signalling can be completed.
Without this, the root hub timer will not fire again to check
if the resume was completed and there will be a never-ending wait on
on the port.
This effect is only observed if the HUB IRQ IN does not come after we
have initiated the port resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 203a86613f upstream.
When the host controller fails to respond to an Enable Slot command, and
the host fails to respond to the register write to abort the command
ring, the xHCI driver will assume the host is dead, and call
usb_hc_died().
The USB device's slot_id is still set to zero, and the pointer stored at
xhci->devs[0] will always be NULL. The call to xhci_check_args in
xhci_free_dev should have caught the NULL virt_dev pointer.
However, xhci_free_dev is designed to free the xhci_virt_device
structures, even if the host is dead, so that we don't leak kernel
memory. xhci_free_dev checks the return value from the generic
xhci_check_args function. If the return value is -ENODEV, it carries on
trying to free the virtual device.
The issue is that xhci_check_args looks at the host controller state
before it looks at the xhci_virt_device pointer. It will return -ENIVAL
because the host is dead, and xhci_free_dev will ignore the return
value, and happily dereference the NULL xhci_virt_device pointer.
The fix is to make sure that xhci_check_args checks the xhci_virt_device
pointer before it checks the host state.
See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for
further details. This patch doesn't solve the underlying issue, but
will ensure we don't see any more NULL pointer dereferences because of
the issue.
This patch should be backported to kernels as old as 3.1, that
contain the commit 7bd89b4017 "xhci: Don't
submit commands or URBs to halted hosts."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Vincent Thiele <vincentthiele@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d66eaf9f89 upstream.
in some cases where device is attched to xhci port and do not responding,
for example ath9k_htc with stalled firmware, kernel will
crash on ring_doorbell_for_active_rings.
This patch check if pointer exist before it is used.
This patch should be backported to kernels as old as 2.6.35, that
contain the commit e9df17eb14 "USB: xhci:
Correct assumptions about number of rings per endpoint"
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07f3cb7c28 upstream.
Xhci controllers with hci_version > 0.96 gives spurious success
events on short packet completion. During webcam capture the
"ERROR Transfer event TRB DMA ptr not part of current TD" was observed.
The same application works fine with synopsis controllers hci_version 0.96.
The same issue is seen with Intel Pantherpoint xhci controller. So enabling
this quirk in xhci_gen_setup if controller verion is greater than 0.96.
For xhci-pci move the quirk to much generic place xhci_gen_setup.
Note from Sarah:
The xHCI 1.0 spec changed how hardware handles short packets. The HW
will notify SW of the TRB where the short packet occurred, and it will
also give a successful status for the last TRB in a TD (the one with the
IOC flag set). On the second successful status, that warning will be
triggered in the driver.
Software is now supposed to not assume the TD is not completed until it
gets that last successful status. That means we have a slight race
condition, although it should have little practical impact. This patch
papers over that issue.
It's on my long-term to-do list to fix this race condition, but it is a
much more involved patch that will probably be too big for stable. This
patch is needed for stable to avoid serious log spam.
This patch should be backported to kernels as old as 3.0, that
contain the commit ad808333d8 "Intel xhci:
Ignore spurious successful event."
The patch will have to be modified for kernels older than 3.2, since
that kernel added the xhci_gen_setup function for xhci platform devices.
The correct conflict resolution for kernels older than 3.2 is to set
XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09d8091c02 upstream.
Commit a82274151a "tracing: Protect ftrace_trace_arrays list in trace_events.c"
added taking the trace_types_lock mutex in trace_events.c as there were
several locations that needed it for protection. Unfortunately, it also
encapsulated a call to tracing_reset_all_online_cpus() which also takes
the trace_types_lock, causing a deadlock.
This happens when a module has tracepoints and has been traced. When the
module is removed, the trace events module notifier will grab the
trace_types_lock, do a bunch of clean ups, and also clears the buffer
by calling tracing_reset_all_online_cpus. This doesn't happen often
which explains why it wasn't caught right away.
Commit a82274151a was marked for stable, which means this must be
sent to stable too.
Link: http://lkml.kernel.org/r/51EEC646.7070306@broadcom.com
Reported-by: Arend van Spril <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Cc: Alexander Z Lam <azl@google.com>
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Cc: David Sharp <dhsharp@google.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 085b513f97 upstream.
sd_prep_fn will allocate a larger CDB for the command via mempool_alloc
for devices using DIF type 2 protection. This CDB was being freed
in sd_done, which results in a kernel crash if the command is retried
due to a UNIT ATTENTION. This change moves the code to free the larger
CDB into sd_unprep_fn instead, which is invoked after the request is
complete.
It is no longer necessary to call scsi_print_command separately for
this case as the ->cmnd will no longer be NULL in the normal code path.
Also removed conditional test for DIF type 2 when freeing the larger
CDB because the protection_type could have been changed via sysfs while
the command was executing.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96f15f2903 upstream.
This commit fixes a race condition in the isci driver abort task and SSP
device task management path. The race is caused when an I/O termination
in the SCU hardware is necessary because of an SSP target timeout condition,
and the check of the I/O end state races against the HW-termination-driven
end state. The failure of the race meant that no TMF was sent to the device
to clean-up the pending I/O.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Reviewed-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit faefd550c4 upstream.
When CONFIG_ARM_APPENDED_DTB is selected, if the bootloader provides
an ATAG_MEM it replaces the memory size and the memory address in the
memory node of the device tree. In the case of a system which can
handle more than 4GB, the memory node cell size is 4: each data
(memory size and memory address) are 64 bits and then use 2 cells.
The current code in atags_to_fdt.c made the assumption of a cell size
of 2 (one cell for the memory size and one cell for the memory
address), this leads to an improper write of the data and ends with a
boot hang.
This patch writes the memory size and the memory address on the memory
node in the device tree depending of the size of the memory node (32
bits or 64 bits).
It has been tested in the 2 cases:
- with a dtb using skeleton.dtsi
- and with a dtb using skeleton64.dtsi
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 647ab784c5 upstream.
The errors were caused by copy/paste mistake in below commit
since v3.10:
3489d50 ASoC: tegra: Use common DAI DMA data struct
It also corrects slave_id initialization in tegra20_ac97 driver.
Signed-off-by: Richard Zhao <rizhao@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb6f66a2d2 upstream.
The registers of max98088 are 8 bits, not 16 bits. This bug causes the
contents of registers to be overwritten with bad values when the codec
is suspended and then resumed.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0699a73af3 upstream.
Commit 18d627113b (firewire: prevent dropping of completed iso packet
header data) was intended to be an obvious bug fix, but libdc1394 and
FlyCap2 depend on the old behaviour by ignoring all returned information
and thus not noticing that not all packets have been received yet. The
result was that the video frame buffers would be saved before they
contained the correct data.
Reintroduce the old behaviour for old clients.
Tested-by: Stepan Salenikovich <stepan.salenikovich@gmail.com>
Tested-by: Josep Bosch <jep250@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 186a964701 upstream.
This patch adds target_get_sess_cmd reference counting for
iscsit_handle_task_mgt_cmd(), and adds a target_put_sess_cmd()
for the failure case.
It also fixes a bug where ISCSI_OP_SCSI_TMFUNC type commands
where leaking iscsi_cmd->i_conn_node and eventually triggering
an OOPs during struct isert_conn shutdown.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2cb96494d upstream.
This patch addresses a bug where RDMA_CM_EVENT_DISCONNECTED may occur
before the connection shutdown has been completed by rx/tx threads,
that causes isert_free_conn() to wait indefinately on ->conn_wait.
This patch allows isert_disconnect_work code to invoke rdma_disconnect
when isert_disconnect_work() process context is started by client
session reset before isert_free_conn() code has been reached.
It also adds isert_conn->conn_mutex protection for ->state within
isert_disconnect_work(), isert_cq_comp_err() and isert_free_conn()
code, along with isert_check_state() for wait_event usage.
(v2: Add explicit iscsit_cause_connection_reinstatement call
during isert_disconnect_work() to force conn reset)
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fbfc46fb0 upstream.
This patch fixes a potential buffer overflow while processing
iscsi_node_auth input for configfs attributes within NodeACL
tfc_tpg_nacl_auth_cit context.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3df8f68aaf upstream.
This patch adds the missing isert_put_reject() logic to post
a outgoing payload buffer to hold the 48 bytes of original PDU
header request payload for the rejected cmd.
It also fixes ISTATE_SEND_REJECT handling in isert_response_completion()
-> isert_do_control_comp() code, and drops incorrect iscsi_cmd_t->reject_comp
usage.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ea9a69d1a upstream.
The EAPD GPIO is dynamically turned on/off for some machines with
Sigmatel codecs, but this didn't work as expected, and it resulted in
spontaneous lost of speaker outputs per HP plugging or power-saving.
This patch fixes the bug by simply including spec->eapd_mask into
spec->gpio_mask and spec->gpio_data bits.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be2f93a4c4 upstream.
Return SNDRV_PCM_POS_XRUN (snd_pcm_uframes_t) instead of
SNDRV_PCM_STATE_XRUN (snd_pcm_state_t) from the pointer
function of 6fire, as expected by snd_pcm_update_hw_ptr0().
Caught by sparse.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
