UARTs on CNS3xxx are 8250-compatible, not AMBA.
The base address for UART0 is 0x78000000 (physical)
and 0xfb002000 (virtual).
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The newly introduced support for SAMA5D4 added access to the
'AT91_ALT_BASE_SYS' register area, but failed to define the
symbols in the case when CONFIG_MMU is disabled.
We really should not hardwire addresses like this any more,
but as a small fixup, this patch just adds the missing
definitions for the nommu case, which gets at91x40_defconfig
and any configuration of sam9 and sama5 with MMU disabled
back to work.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 726d32bf79 ("ARM: at91: SAMA5D4 SoC detection code and low ...")
Pull "Second SoC batch for 3.18" from Nicolas Ferre:
- introduction of the new SAMA5D4 SoC and associated Evaluation Kit
- low level soc detection and early printk code
- taking advantage of this, documentation of all AT91 SoC DT strings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'at91-soc2' of git://github.com/at91linux/linux-at91:
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
The soc2 branch is based on this cleanup:
* at91/soc:
ARM: at91: Remove the support for the RSI EWS board
ARM: at91: remove board file for Acme Systems Fox G20
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "part 2 of omap SoC changes" from Tony Lindgren:
Few hwmod changes to support upcoming 8250 driver with DMA,
start using the SRAM driver for some omaps, and update the
defconfig.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'soc-part2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
ARM: AM335x: Get rid of unused sram init function
ARM: omap2plus_defconfig: Enable some display features
ARM: omap2plus_defconfig: Enable battery and reset drivers
ARM: omap2plus_defconfig: Add support for distros with systemd
ARM: omap2plus_defconfig: Add cpufreq to defconfig
ARM: omap2plus_defconfig: Shrink with savedefconfig
ARM: OMAP3: Use manual idle for UARTs because of DMA errata
ARM: OMAP2+: Add hwmod flag for HWMOD_RECONFIG_IO_CHAIN
Merge "ARM: BCM: Broadcom BCM63138 support" from Florian Fainelli:
This patchset adds very minimal support for the BCM63138 SoC which is
a xDSL SoC using a dual Cortex A9 CPU complex.
* tag 'bcm63138-v4' of http://github.com/brcm/linux:
MAINTAINERS: add entry for the Broadcom BCM63xx ARM SoCs
ARM: BCM63XX: add BCM963138DVT Reference platform DTS
ARM: BCM63XX: add BCM63138 minimal Device Tree
ARM: BCM63XX: add low-level UART debug support
ARM: BCM63XX: add basic support for the Broadcom BCM63138 DSL SoC
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Fifth Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:
* r8a7740: Fix documentation error copied from elsewhere
* r8a7794: Reserve memory for CMA in a manner consistent to
other R-Car Gen2 SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'renesas-soc5-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740 legacy: Fix copied bug in comment
ARM: shmobile: r8a7794: Reserve memory as other R-Car Gen2 SoCs
Pull "fix PXA3xx SSP naming issue" from Haojian Zhuang:
It's imported by 972a55b62 ASoC: fix pxa-ssp compiling issue under mach-mmp from v3.5
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'pxa3xx-ssp-name' of https://git.kernel.org/pub/scm/linux/kernel/git/hzhuang1/linux:
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
Pull "ARM: tegra: core SoC code changes for 3.18" from Stephen Warren:
the primary change here gets its address information from DT rather than
iomap.h. This removes one more user of iomap.h, and will help allow the
code to move to a location that can be shared between arch/arm and
arch/arm64.
An unused header file was also removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'tegra-for-3.18-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: remove unused tegra_emc.h
ARM: tegra: Initialize flow controller from DT
of: Add NVIDIA Tegra flow controller bindings
This patch adds the basic machine file for the MesonX SoCs. Only Meson6
is populated.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the UART definitions needed to support earlyprintk for MesonX SoCs
on UARTAO.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "ARM: imx: SoC updates for 3.18" from Shawn Guo:
The i.MX SoC updates for 3.18:
- Add initial devicetree support for i.MX1
- Support GPT per clock source from OSC for i.MX6
- A couple of parent selection corrections for i.MX6SL clock driver
- Support more chip revision for i.MX6
- Convert pr_warning to pr_warn
- Add exclusive gate clock support
- Add BYPASS support for i.MX6 PLL clocks
- Update i.MX6 clock tree for audio use case
- A couple of VF610 clock driver updates
* tag 'imx-soc-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (30 commits)
ARM: imx_v6_v7_defconfig updates
ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM
arm: mach-imx: Convert pr_warning to pr_warn
ARM: imx: source gpt per clk from OSC for system timer
ARM: imx: add gpt_3m clk for i.mx6qdl
ARM: imx: fix register offset of pll7_usb_host gate clock
ARM: clk-imx6sl: refine clock tree for SSI
ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver
ARM: imx6sx: add BYPASS support for PLL clocks
ARM: imx6sl: add BYPASS support for PLL clocks
ARM: imx6q: add BYPASS support for PLL clocks
ARM: imx: add an exclusive gate clock type
ARM: clk-imx6q: refine clock tree for SSI
ARM: clk-imx6q: refine clock tree for ASRC
ARM: clk-imx6sl: correct the pxp and epdc axi clock selections
ARM: clk-imx6q: refine clock tree for ESAI
ARM: clk-imx6sl: Select appropriate parents for LCDIF clocks
ARM: clk-imx6sl: Remove csi_lcdif_sels[]
ARM: imx: clk-vf610: Add USBPHY clocks
ARM: imx: add cpufreq support for i.mx6sx
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Fourth Round of Renesas ARM Based SoC Soc Updates for v3.18" from Simon Horman:
Fourth Round of Renesas ARM Based SoC Soc Updates for v3.18
* r8a7794: Remove unnecessary #ifdef CONFIG_USE_OF
* tag 'renesas-soc4-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7794: Remove unnecessary #ifdef CONFIG_USE_OF
Signed-off-by: Olof Johansson <olof@lixom.net>
When compiling with "ARCH=arm" and "allmodconfig",
with commit: 9cdc99919a [2/7] ARM: hisi: enable MCPM implementation
we will get:
/tmp/cc6DjYjT.s: Assembler messages:
/tmp/cc6DjYjT.s:63: Error: selected processor does not support ARM mode `ubfx r1,r0,#8,#8'
/tmp/cc6DjYjT.s:761: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:762: Error: selected processor does not support ARM mode `dsb '
/tmp/cc6DjYjT.s:769: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:775: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:776: Error: selected processor does not support ARM mode `dsb '
/tmp/cc6DjYjT.s:795: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:801: Error: selected processor does not support ARM mode `isb '
/tmp/cc6DjYjT.s:802: Error: selected processor does not support ARM mode `dsb '
Fix platmcpm compilation when ARMv6 is selected.
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
HIP04 was added out of order, but so was the previous HISI debug uart
support as well. Minor reshuffling of order.
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Second Round of Renesas ARM Based SoC Clk Updates for v3.18" from Simon Horman.
* Add r8a7740, sh73a0 SoCs to MSTP bindings
* tag 'renesas-clk2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
clk: shmobile: Add r8a7740, sh73a0 SoCs to MSTP bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
SoC related changes for omaps for v3.18 merge window:
- PM changes to make the code easier to use on newer SoCs
- PM changes for newer SoCs suspend and resume and wake-up events
- Minor clean-up to remove dead Kconfig options
Note that these have a dependency to the fixes-v3.18-not-urgent
tag and is based on a commit in that series.
* tag 'soc-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (514 commits)
ARM: OMAP5+: Reuse OMAP4 PM code for OMAP5 and DRA7
ARM: dts: OMAP3+: Add PRM interrupt
ARM: omap: Remove stray ARCH_HAS_OPP references
ARM: DRA7: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5: Add hook in SoC initcalls to enable pm initialization
ARM: OMAP5 / DRA7: Enable CPU RET on suspend
ARM: OMAP5 / DRA7: PM: Provide a dummy startup function for CPU hotplug
ARM: OMAP5 / DRA7: PM: Avoid all SAR saves
ARM: OMAP5 / DRA7: PM: Enable Mercury retention mode on CPUx powerdomains
ARM: OMAP5 / DRA7: PM / wakeupgen: Enables ES2 PM mode by default
ARM: OMAP5 / DRA7: PM: Set MPUSS-EMIF clock-domain static dependency
ARM: OMAP5 / DRA7: PM: Update CPU context register offset
ARM: AM437x: use pdata quirks for pinctrl information
ARM: DRA7: use pdata quirks for pinctrl information
ARM: OMAP5: use pdata quirks for pinctrl information
ARM: OMAP4+: PM: Use only valid low power state for CPU hotplug
ARM: OMAP4+: PM: use only valid low power state for suspend
ARM: OMAP4+: PM: Make logic state programmable
ARM: OMAP2+: powerdomain: introduce logic for finding valid power domain
ARM: OMAP2+: powerdomain: pwrdm_for_each_clkdm iterate only valid clkdms
...
Add sama5d4 to sama5_defconfig to build kernel booting on both sama5d3 and
samad4.
Note that earlyprintk can only be working for one or the other.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
SoC identification code, kernel uncompress and low level
debugging routines update.
On SAMA5D4, DBGU is at another address AT91_BASE_DBGU2 so another
round of detection is needed. We also had to differentiate with
SAMA5D3 SoC family and rename some variables.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Newer SoCs have two different AHB interconnect. The AHB 32 bits Matrix
interconnect (h32mx) has a clock that can be setup at the half of the h64mx
clock (which is mck). The h32mx clock can not exceed 90 MHz.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The platform is end of life/support and should not clutter
the mach-at91 directory with non-DT files. It is therefore
removed.
Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Currently, devices for SSP ports 1, 2 and 3 are registered as compatible
devices to pxa27x-ssp. While the actual IP core is comparable, there are
some subtle differences which users of the SSP ports address by looking at
the 'type' field.
By registering devices of type 'pxa27x-ssp', this 'type' field is
incorrectly set to PXA27x_SSP which confuses the users.
To fix this, provide specific ssp port plaform devices which use
'pxa3xx-ssp' as driver name, an instantiate them from pxa3xx.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Provide an explicit match string for PXA3xx SSP ports.
Without this match string, SSP0/SSP1/SSP2 in PXA3xxx will be consided as
PXA27x SSP Port.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
In order to handle errata I688, a page of sram was reserved by doing a
static iotable map. Now that we use gen_pool to manage sram, we can
completely remove all of these static mappings and use gen_pool_alloc()
to get the one page of sram space needed to implement errata I688.
omap_bus_sync will be NOP until SRAM initialization happens.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use drivers/misc/sram.c driver to manage SRAM on all DT only
OMAP platforms (am33xx, am43xx, omap4 and omap5) instead of
the existing private plat-omap/sram.c
Address and size related data is removed from mach-omap2/sram.c
and now passed to drivers/misc/sram.c from DT.
Users can hence use general purpose allocator apis instead of
OMAP private ones to manage and use SRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have panel support for DT based booting,
let's make it usable and enable most things as modules.
Note that omap3 boards need also the ads7847 module for
the panel that we're now changing to a loadable module.
And n900 seems to require setting the brightness via
sysfs for acx565akm/brightness after modprobe of
panel_sony_acx565akm and omapfb.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since many omaps run on battery, we should have the battery
drivers enabled. Let's also enable the reset driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that we can now use the CONFIG_GENERIC_CPUFREQ_CPU0,
so let's only enable that. Let's use CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND
as suggested by Nishant.
And also let's enable thermal as explained by Nishant Menon:
Many TI SoCs using Highest frequency is not really too nice of an idea for
long periods of time. And not everything is upstream to support things
optimially - example avs class 0, 1.5 ABB consolidation with cpufreq etc..
We definitely need thermal enabled as well for device safety needs.
[tony@atomide.com: updated per Nishant's suggestions]
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In sprz318f.pdf "Usage Note 2.7" says that UARTs cannot acknowledge
idle requests in smartidle mode when configured for DMA operations.
This prevents L4 from going idle. So let's use manual idle mode
instead.
Otherwise systems using Sebastian's 8250 patches with DMA will
never enter deeper idle states because of the errata above.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cc824534d4 ("ARM: OMAP2+: hwmod: Rearm wake-up interrupts
for DT when MUSB is idled") fixed issues with hung UART wake-up
events by calling _reconfigure_io_chain() when MUSB is connected
or disconnected.
As pointed out by Paul Walmsley, we may need to also call
_reconfigure_io_chain() in other cases, so it should be a separate
flag. Let's add HWMOD_RECONFIG_IO_CHAIN as suggested by Paul.
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a MAINTAINERS entry covering all the Broadcom BCM63xx ARM DSL SoCs
files along with the relevant git tree and mailing-list.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a very minimalistic BCM63138 Device Tree include file which
describes the BCM63138 SoC with only the basic set of required
peripherals:
- Cortex A9 CPUs
- ARM GIC
- ARM SCU
- PL310 Level-2 cache controller
- ARM TWD & Global timers
- ARM TWD watchdog
- legacy MIPS bus (UBUS)
- BCM6345-style UARTs (disabled by default)
Since the PL310 L2 cache controller does not come out of reset with
correct default values, we need to override the 'cache-sets' and
'cache-size' properties to get its geometry right.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom BCM63xx DSL SoCs have a different UART implementation for which
we need specially crafted low-level debug assembly code to support. Add
support for this using the standard definitions provided in
include/linux/serial_bcm63xx.h (shared with their MIPS counterparts).
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds basic support for the Broadcom BCM63138 DSL SoC which is
using a dual-core Cortex A9 system. Add the very minimum required code
boot Linux on this SoC.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The corresponding bug in pm-sh7372.c was fixed in commit
70fe7b2467 ("ARM: shmobile: Do not access sh7372 A4S domain
internals directly").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As Acme Systems Fox G20 is available in Device Tree flavor and that we plan to
remove all the board files soon, we can remove this one without problem.
If you use this board, please use a DT-enabled at91sam9g20 kernel with
at91-foxg20.dts.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Sergio Tanzilli <tanzilli@acmesystems.it>
AUX setting has no effect that's why remove it.
Warning log:
L2C: platform provided aux values match the hardware, so
have no effect. Please remove them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Match the naming pattern of all other SMP ops and rename
zynq_platform_cpu_die --> zynq_cpu_die.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
