commit 72d00e560d upstream.
Since commit b09c68dc57 ("clk: imx: pll14xx: Support dynamic rates"),
the driver has the ability to dynamically compute PLL parameters to
approximate the requested rates. This is not always used, because the
logic is as follows:
- Check if the target rate is hardcoded in the frequency table
- Check if varying only kdiv is possible, so switch over is glitch free
- Compute rate dynamically by iterating over pdiv range
If we skip the frequency table for the 1443x PLL, we find that the
computed values differ to the hardcoded ones. This can be valid if the
hardcoded values guarantee for example an earlier lock-in or if the
divisors are chosen, so that other important rates are more likely to
be reached glitch-free.
For rates (393216000 and 361267200, this doesn't seem to be the case:
They are only approximated by existing parameters (393215995 and
361267196 Hz, respectively) and they aren't reachable glitch-free from
other hardcoded frequencies. Dropping them from the table allows us
to lock-in to these frequencies exactly.
This is immediately noticeable because they are the assigned-clock-rates
for IMX8MN_AUDIO_PLL1 and IMX8MN_AUDIO_PLL2, respectively and a look
into clk_summary so far showed that they were a few Hz short of the target:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267196 0 0 50000 N
audio_pll1_out 1 1 0 393215995 0 0 50000 Y
and afterwards:
imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out 0 0 0 361267200 0 0 50000 N
audio_pll1_out 1 1 0 393216000 0 0 50000 Y
This change is equivalent to adding following hardcoded values:
/* rate mdiv pdiv sdiv kdiv */
PLL_1443X_RATE(393216000, 655, 5, 3, 23593),
PLL_1443X_RATE(361267200, 497, 33, 0, -16882),
Fixes: 053a4ffe29 ("clk: imx: imx8mm: fix audio pll setting")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-2-m.felsch@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5301c9071 upstream.
First argument of acpi_*_address_space_handler() APIs is acpi_handle of
the device, which is incorrectly passed in driver ->remove() path here.
Fix it by passing the appropriate argument and while at it, make both
API calls consistent using ACPI_HANDLE().
Fixes: a0b028597d ("pinctrl: cherryview: Add support for GMMR GPIO opregion")
Cc: stable@vger.kernel.org
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 358ad816e5 upstream.
Older PA-RISC machines have LEDs which show the disk- and LAN-activity.
The computation is done in software and takes quite some time, e.g. on a
J6500 this may take up to 60% time of one CPU if the machine is loaded
via network traffic.
Since most people don't care about the LEDs, start with LEDs disabled and
just show a CPU heartbeat LED. The disk and LAN LEDs can be turned on
manually via /proc/pdc/led.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb78fa86e upstream.
test_pages() tests the page allocator by calling alloc_pages() with
different orders up to order 10.
However, different architectures and platforms support different maximum
contiguous allocation sizes. The default maximum allocation order
(MAX_ORDER) is 10, but architectures can use CONFIG_ARCH_FORCE_MAX_ORDER
to override this. On platforms where this is less than 10, test_meminit()
will blow up with a WARN(). This is expected, so let's not do that.
Replace the hardcoded "10" with the MAX_ORDER macro so that we test
allocations up to the expected platform limit.
Link: https://lkml.kernel.org/r/20230714015238.47931-1-ajd@linux.ibm.com
Fixes: 5015a300a5 ("lib: introduce test_meminit module")
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Cc: Xiaoke Wang <xkernel.wang@foxmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ce2c24cb6 upstream.
The local variable @page in __split_vmemmap_huge_pmd() to obtain a pmd
page without holding page_table_lock may possiblely get the page table
page instead of a huge pmd page.
The effect may be in set_pte_at() since we may pass an invalid page
struct, if set_pte_at() wants to access the page struct (e.g.
CONFIG_PAGE_TABLE_CHECK is enabled), it may crash the kernel.
So fix it. And inline __split_vmemmap_huge_pmd() since it only has one
user.
Link: https://lkml.kernel.org/r/20230707033859.16148-1-songmuchun@bytedance.com
Fixes: d8d55f5616 ("mm: sparsemem: use page table lock to protect kernel pmd operations")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86327e8eb9 upstream.
kmem.limit_in_bytes (v1 way to limit kernel memory usage) has been
deprecated since 58056f7750 ("memcg, kmem: further deprecate
kmem.limit_in_bytes") merged in 5.16. We haven't heard about any serious
users since then but it seems that the mere presence of the file is
causing more harm thatn good. We (SUSE) have had several bug reports from
customers where Docker based containers started to fail because a write to
kmem.limit_in_bytes has failed.
This was unexpected because runc code only expects ENOENT (kmem disabled)
or EBUSY (tasks already running within cgroup). So a new error code was
unexpected and the whole container startup failed. This has been later
addressed by
52390d6804
so current Docker runtimes do not suffer from the problem anymore. There
are still older version of Docker in use and likely hard to get rid of
completely.
Address this by wiping out the file completely and effectively get back to
pre 4.5 era and CONFIG_MEMCG_KMEM=n configuration.
I would recommend backporting to stable trees which have picked up
58056f7750 ("memcg, kmem: further deprecate kmem.limit_in_bytes").
[mhocko@suse.com: restore _KMEM switch case]
Link: https://lkml.kernel.org/r/ZKe5wxdbvPi5Cwd7@dhcp22.suse.cz
Link: https://lkml.kernel.org/r/20230704115240.14672-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Tejun Heo <tj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09ee7a3bf8 upstream.
The ChannelSequence field in the SMB3 header is supposed to be
increased after reconnect to allow the server to distinguish
requests from before and after the reconnect. We had always
been setting it to zero. There are cases where incrementing
ChannelSequence on requests after network reconnects can reduce
the chance of data corruptions.
See MS-SMB2 3.2.4.1 and 3.2.7.1
Signed-off-by: Steve French <stfrench@microsoft.com>
Cc: stable@vger.kernel.org # 5.16+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db67345716 upstream.
It looks like txdv-skew-psec is a typo from a copy+paste. txdv-skew-psec
is not present in the PHY bindings nor is it in the driver.
Correct to txen-skew-psec which is clearly what it was meant to be.
Given that the default for txen-skew-psec is 0, and the device tree is
only trying to set it to 0 anyway, there should not be any functional
change from this fix.
Fixes: 361b0dcbd7 ("arm64: dts: renesas: rzg2l-smarc-som: Enable Ethernet")
Fixes: 6494e4f905 ("arm64: dts: renesas: rzg2ul-smarc-som: Enable Ethernet on SMARC platform")
Fixes: ce0c63b6a5 ("arm64: dts: renesas: Add initial device tree for RZ/G2LC SMARC EVK")
Cc: stable@vger.kernel.org # 6.1.y
Reported-by: Tomohiro Komagata <tomohiro.komagata.aj@renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230609221136.7431-1-chris.paterson2@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d900d9a435 upstream.
Sample rate conversions for rates greater than 48kHz are found to be
failing. It means x->y conversions fail when either x or y is greater
than 48kHz.
This happens because, tegra210_sfc_rate_to_idx() returns incorrect
index for rates greater than 48kHz. This actually depends on the
tegra210_sfc_rates[] array and it is not in sync with frequency
values of SFC TX/RX register. To be precise, 64kHz entry is missing
in above array defined in the driver. Due to this wrong index is
returned and this results in incorrect programming of coefficients.
To fix this, align the tegra210_sfc_rates[] array with SFC register
specification and thus add 64kHz entry to it. Also, the coefficient
table is updated to reflect that none of the conversions are supported
for 64kHz.
Fixes: b2f74ec53a ("ASoC: tegra: Add Tegra210 based SFC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sheetal <sheetal@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/Message-Id: <1687433656-7892-2-git-send-email-spujar@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a26e45edb upstream.
When doing io_uring benchmark on /dev/nullb0, it's easy to crash the
kernel if poll requests timeout triggered, as reported by David. [1]
BUG: kernel NULL pointer dereference, address: 0000000000000008
Workqueue: kblockd blk_mq_timeout_work
RIP: 0010:null_timeout_rq+0x4e/0x91
Call Trace:
? null_timeout_rq+0x4e/0x91
blk_mq_handle_expired+0x31/0x4b
bt_iter+0x68/0x84
? bt_tags_iter+0x81/0x81
__sbitmap_for_each_set.constprop.0+0xb0/0xf2
? __blk_mq_complete_request_remote+0xf/0xf
bt_for_each+0x46/0x64
? __blk_mq_complete_request_remote+0xf/0xf
? percpu_ref_get_many+0xc/0x2a
blk_mq_queue_tag_busy_iter+0x14d/0x18e
blk_mq_timeout_work+0x95/0x127
process_one_work+0x185/0x263
worker_thread+0x1b5/0x227
This is indeed a race problem between null_timeout_rq() and null_poll().
null_poll() null_timeout_rq()
spin_lock(&nq->poll_lock)
list_splice_init(&nq->poll_list, &list)
spin_unlock(&nq->poll_lock)
while (!list_empty(&list))
req = list_first_entry()
list_del_init()
...
blk_mq_add_to_batch()
// req->rq_next = NULL
spin_lock(&nq->poll_lock)
// rq->queuelist->next == NULL
list_del_init(&rq->queuelist)
spin_unlock(&nq->poll_lock)
Fix these problems by setting requests state to MQ_RQ_COMPLETE under
nq->poll_lock protection, in which null_timeout_rq() can safely detect
this race and early return.
Note this patch just fix the kernel panic when request timeout happen.
[1] https://lore.kernel.org/all/3893581.1691785261@warthog.procyon.org.uk/
Fixes: 0a593fbbc2 ("null_blk: poll queue support")
Reported-by: David Howells <dhowells@redhat.com>
Tested-by: David Howells <dhowells@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Link: https://lore.kernel.org/r/20230901120306.170520-2-chengming.zhou@linux.dev
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d0b65569c upstream.
Fix race condition between Interrupt thread and Chip reset thread in trying
to flush the same mailbox. With the race condition, the "ha->mbx_intr_comp"
will get an extra complete() call. The extra complete call create erroneous
mailbox timeout condition when the next mailbox is sent where the mailbox
call does not wait for interrupt to arrive. Instead, it advances without
waiting.
Add lock protection around the check for mailbox completion.
Cc: stable@vger.kernel.org
Fixes: b2000805a9 ("scsi: qla2xxx: Flush mailbox commands on chip reset")
Signed-off-by: Quinn Tran <quinn.tran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230821130045.34850-3-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b51f35d12 upstream.
Link up failure occurred where driver failed to see certain events from FW
indicating link up (AEN 8011) and fabric login completion (AEN 8014).
Without these 2 events, driver would not proceed forward to scan the
fabric. The cause of this is due to delay in the receive of interrupt for
Mailbox 60 that causes qla to set the fw_started flag late. The late
setting of this flag causes other interrupts to be dropped. These dropped
interrupts happen to be the link up (AEN 8011) and fabric login completion
(AEN 8014).
Set fw_started flag early to prevent interrupts being dropped.
Cc: stable@vger.kernel.org
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-6-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da7c21b72a upstream.
For each TMF request, driver iterates through each qpair and flushes
commands associated to the TMF. At the end of the qpair flush, a Marker is
used to complete the flush transaction. This process was repeated for each
qpair. The multiple flush and marker for this TMF request seems to cause
confusion for FW.
Instead, 1 flush is sent to FW. Driver would wait for FW to go through all
the I/Os on each qpair to be read then return. Driver then closes out the
transaction with a Marker.
Cc: stable@vger.kernel.org
Fixes: d90171dd0d ("scsi: qla2xxx: Multi-que support for TMF")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-5-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6dfe4344c1 upstream.
System crash when using debug kernel due to link list corruption. The cause
of the link list corruption is due to session deletion was allowed to queue
up twice. Here's the internal trace that show the same port was allowed to
double queue for deletion on different cpu.
20808683956 015 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1
20808683957 027 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1
Move the clearing/setting of deleted flag lock.
Cc: stable@vger.kernel.org
Fixes: 726b854870 ("qla2xxx: Add framework for async fabric discovery")
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Link: https://lore.kernel.org/r/20230714070104.40052-2-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70d1ace56d upstream.
We don't want to create a fence for every command submission. It's
only necessary when userspace provides a waitable token for submission.
This could be:
1) bo_handles, to be used with VIRTGPU_WAIT
2) out_fence_fd, to be used with dma_fence apis
3) a ring_idx provided with VIRTGPU_CONTEXT_PARAM_POLL_RINGS_MASK
+ DRM event API
4) syncobjs in the future
The use case for just submitting a command to the host, and expecting
no response. For example, gfxstream has GFXSTREAM_CONTEXT_PING that
just wakes up the host side worker threads. There's also
CROSS_DOMAIN_CMD_SEND which just sends data to the Wayland server.
This prevents the need to signal the automatically created
virtio_gpu_fence.
In addition, VIRTGPU_EXECBUF_RING_IDX is checked when creating a
DRM event object. VIRTGPU_CONTEXT_PARAM_POLL_RINGS_MASK is
already defined in terms of per-context rings. It was theoretically
possible to create a DRM event on the global timeline (ring_idx == 0),
if the context enabled DRM event polling. However, that wouldn't
work and userspace (Sommelier). Explicitly disallow it for
clarity.
Signed-off-by: Gurchetan Singh <gurchetansingh@chromium.org>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> # edited coding style
Link: https://patchwork.freedesktop.org/patch/msgid/20230707213124.494-1-gurchetansingh@chromium.org
Signed-off-by: Alyssa Ross <hi@alyssa.is>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Jens Axboe <axboe@kernel.dk>
[ upstream commit ebdfefc09c ]
If we setup the ring with SQPOLL, then that polling thread has its
own io-wq setup. This means that if the application uses
IORING_REGISTER_IOWQ_AFF to set the io-wq affinity, we should not be
setting it for the invoking task, but rather the sqpoll task.
Add an sqpoll helper that parks the thread and updates the affinity,
and use that one if we're using SQPOLL.
Fixes: fe76421d1d ("io_uring: allow user configurable IO thread CPU affinity")
Cc: stable@vger.kernel.org # 5.10+
Link: https://github.com/axboe/liburing/discussions/884
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ upstream commit 45500dc4e0 ]
io-wq will retry iopoll even when it failed with -EAGAIN. If that
races with task exit, which sets TIF_NOTIFY_SIGNAL for all its workers,
such workers might potentially infinitely spin retrying iopoll again and
again and each time failing on some allocation / waiting / etc. Don't
keep spinning if io-wq is dying.
Fixes: 561fb04a6a ("io_uring: replace workqueue usage with io-wq")
Cc: stable@vger.kernel.org
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Dylan Yudaken <dylany@meta.com>
[ upstream commit c06c6c5d27 ]
This is required for the failure case (io_req_complete_failed) and is
missing.
The alternative would be to only lock in the failure path, however all of
the non-error paths in io_poll_check_events that do not do not return
IOU_POLL_NO_ACTION end up locking anyway. The only extraneous lock would
be for the multishot poll overflowing the CQE ring, however multishot poll
would probably benefit from being locked as it will allow completions to
be batched.
So it seems reasonable to lock always.
Signed-off-by: Dylan Yudaken <dylany@meta.com>
Link: https://lore.kernel.org/r/20221124093559.3780686-3-dylany@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 669281ee7e upstream.
MGLRU has a LRU list for each zone for each type (anon/file) in each
generation:
long nr_pages[MAX_NR_GENS][ANON_AND_FILE][MAX_NR_ZONES];
The min_seq (oldest generation) can progress independently for each
type but the max_seq (youngest generation) is shared for both anon and
file. This is to maintain a common frame of reference.
In order for eviction to advance the min_seq of a type, all the per-zone
lists in the oldest generation of that type must be empty.
The eviction logic only considers pages from eligible zones for
eviction or promotion.
scan_folios() {
...
for (zone = sc->reclaim_idx; zone >= 0; zone--) {
...
sort_folio(); // Promote
...
isolate_folio(); // Evict
}
...
}
Consider the system has the movable zone configured and default 4
generations. The current state of the system is as shown below
(only illustrating one type for simplicity):
Type: ANON
Zone DMA32 Normal Movable Device
Gen 0 0 0 4GB 0
Gen 1 0 1GB 1MB 0
Gen 2 1MB 4GB 1MB 0
Gen 3 1MB 1MB 1MB 0
Now consider there is a GFP_KERNEL allocation request (eligible zone
index <= Normal), evict_folios() will return without doing any work
since there are no pages to scan in the eligible zones of the oldest
generation. Reclaim won't make progress until triggered from a ZONE_MOVABLE
allocation request; which may not happen soon if there is a lot of free
memory in the movable zone. This can lead to OOM kills, although there
is 1GB pages in the Normal zone of Gen 1 that we have not yet tried to
reclaim.
This issue is not seen in the conventional active/inactive LRU since
there are no per-zone lists.
If there are no (not enough) folios to scan in the eligible zones, move
folios from ineligible zone (zone_index > reclaim_index) to the next
generation. This allows for the progression of min_seq and reclaiming
from the next generation (Gen 1).
Qualcomm, Mediatek and raspberrypi [1] discovered this issue independently.
[1] https://github.com/raspberrypi/linux/issues/5395
Link: https://lkml.kernel.org/r/20230802025606.346758-1-kaleshsingh@google.com
Fixes: ac35a49023 ("mm: multi-gen LRU: minimal implementation")
Signed-off-by: Kalesh Singh <kaleshsingh@google.com>
Reported-by: Charan Teja Kalla <quic_charante@quicinc.com>
Reported-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> [mediatek]
Tested-by: Charan Teja Kalla <quic_charante@quicinc.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Brian Geffon <bgeffon@google.com>
Cc: Jan Alexander Steffens (heftig) <heftig@archlinux.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Qi Zheng <zhengqi.arch@bytedance.com>
Cc: Steven Barrett <steven@liquorix.net>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Aneesh Kumar K V <aneesh.kumar@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5e2151ff9 upstream.
__skb_get_hash_symmetric() was added to compute a symmetric hash over
the protocol, addresses and transport ports, by commit eb70db8756
("packet: Use symmetric hash for PACKET_FANOUT_HASH."). It uses
flow_keys_dissector_symmetric_keys as the flow_dissector to incorporate
IPv4 addresses, IPv6 addresses and ports. However, it should not specify
the flag as FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL, which stops further
dissection when an IPv6 flow label is encountered, making transport
ports not being incorporated in such case.
As a consequence, the symmetric hash is based on 5-tuple for IPv4 but
3-tuple for IPv6 when flow label is present. It caused a few problems,
e.g. when nft symhash and openvswitch l4_sym rely on the symmetric hash
to perform load balancing as different L4 flows between two given IPv6
addresses would always get the same symmetric hash, leading to uneven
traffic distribution.
Removing the use of FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL makes sure the
symmetric hash is based on 5-tuple for both IPv4 and IPv6 consistently.
Fixes: eb70db8756 ("packet: Use symmetric hash for PACKET_FANOUT_HASH.")
Reported-by: Lars Ekman <uablrek@gmail.com>
Closes: https://github.com/antrea-io/antrea/issues/5457
Signed-off-by: Quan Tian <qtian@vmware.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23970a1c94 upstream.
The clang build reports this error
fs/udf/inode.c:805:6: error: variable 'newblock' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (*err < 0)
^~~~~~~~
newblock is never set before error handling jump.
Initialize newblock to 0 and remove redundant settings.
Fixes: d8b39db5fab8 ("udf: Handle error when adding extent to a file")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20221230175341.1629734-1-trix@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cf9d015be upstream.
After commit c28cd1f343 ("clk: Mark a fwnode as initialized when using
CLK_OF_DECLARE() macro"), drivers/clk/mvebu/kirkwood.c fails to build:
drivers/clk/mvebu/kirkwood.c:358:1: error: expected identifier or '('
CLK_OF_DECLARE(98dx1135_clk, "marvell,mv98dx1135-core-clock",
^
include/linux/clk-provider.h:1367:21: note: expanded from macro 'CLK_OF_DECLARE'
static void __init name##_of_clk_init_declare(struct device_node *np) \
^
<scratch space>:124:1: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
drivers/clk/mvebu/kirkwood.c:358:1: error: invalid digit 'd' in decimal constant
include/linux/clk-provider.h:1372:34: note: expanded from macro 'CLK_OF_DECLARE'
OF_DECLARE_1(clk, name, compat, name##_of_clk_init_declare)
^
<scratch space>:125:3: note: expanded from here
98dx1135_clk_of_clk_init_declare
^
C function names must start with either an alphabetic letter or an
underscore. To avoid generating invalid function names from clock names,
add two underscores to the beginning of the identifier.
Fixes: c28cd1f343 ("clk: Mark a fwnode as initialized when using CLK_OF_DECLARE() macro")
Suggested-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230308-clk_of_declare-fix-v1-1-317b741e2532@kernel.org
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a50d9403f upstream.
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827da ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c28cd1f343 upstream.
We already mark fwnodes as initialized when they are registered as clock
providers. We do this so that fw_devlink can tell when a clock driver
doesn't use the driver core framework to probe/initialize its device.
This ensures fw_devlink doesn't block the consumers of such a clock
provider indefinitely.
However, some users of CLK_OF_DECLARE() macros don't use the same node
that matches the macro as the node for the clock provider, but they
initialize the entire node. To cover these cases, also mark the nodes
that match the macros as initialized when the init callback function is
called.
An example of this is "stericsson,u8500-clks" that's handled using
CLK_OF_DECLARE() and looks something like this:
clocks {
compatible = "stericsson,u8500-clks";
prcmu_clk: prcmu-clock {
#clock-cells = <1>;
};
prcc_pclk: prcc-periph-clock {
#clock-cells = <2>;
};
prcc_kclk: prcc-kernel-clock {
#clock-cells = <2>;
};
prcc_reset: prcc-reset-controller {
#reset-cells = <2>;
};
...
};
This patch makes sure that "clocks" is marked as initialized so that
fw_devlink knows that all nodes under it have been initialized. If the
driver creates struct devices for some of the subnodes, fw_devlink is
smart enough to know to wait for those devices to probe, so no special
handling is required for those cases.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdamxDX6EBVjKX5=D3rkHp17f5pwGdBVhzFU90-0MHY6dQ@mail.gmail.com/
Fixes: 4a032827da ("of: property: Simplify of_link_to_phandle()")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20230302014639.297514-1-saravanak@google.com
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 433279beba upstream.
Commit 3e45352259 ("md: Free resources in __md_stop") tried to fix
null-ptr-deference for 'active_io' by moving percpu_ref_exit() to
__md_stop(), however, the commit also moving 'writes_pending' to
__md_stop(), and this will cause mdadm tests broken:
BUG: kernel NULL pointer dereference, address: 0000000000000038
Oops: 0000 [#1] PREEMPT SMP
CPU: 15 PID: 17830 Comm: mdadm Not tainted 6.3.0-rc3-next-20230324-00009-g520d37
RIP: 0010:free_percpu+0x465/0x670
Call Trace:
<TASK>
__percpu_ref_exit+0x48/0x70
percpu_ref_exit+0x1a/0x90
__md_stop+0xe9/0x170
do_md_stop+0x1e1/0x7b0
md_ioctl+0x90c/0x1aa0
blkdev_ioctl+0x19b/0x400
vfs_ioctl+0x20/0x50
__x64_sys_ioctl+0xba/0xe0
do_syscall_64+0x6c/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
And the problem can be reporduced 100% by following test:
mdadm -CR /dev/md0 -l1 -n1 /dev/sda --force
echo inactive > /sys/block/md0/md/array_state
echo read-auto > /sys/block/md0/md/array_state
echo inactive > /sys/block/md0/md/array_state
Root cause:
// start raid
raid1_run
mddev_init_writes_pending
percpu_ref_init
// inactive raid
array_state_store
do_md_stop
__md_stop
percpu_ref_exit
// start raid again
array_state_store
do_md_run
raid1_run
mddev_init_writes_pending
if (mddev->writes_pending.percpu_count_ptr)
// won't reinit
// inactive raid again
...
percpu_ref_exit
-> null-ptr-deference
Before the commit, 'writes_pending' is exited when mddev is freed, and
it's safe to restart raid because mddev_init_writes_pending() already make
sure that 'writes_pending' will only be initialized once.
Fix the prblem by moving 'writes_pending' back, it's a litter hard to find
the relationship between alloc memory and free memory, however, code
changes is much less and we lived with this for a long time already.
Fixes: 3e45352259 ("md: Free resources in __md_stop")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230328094400.1448955-1-yukuai1@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 303a780520 upstream.
I found that the read code might send multiple requests using the same
nfs_pgio_header, but nfs4_proc_read_setup() is only called once. This is
how we ended up occasionally double-freeing the scratch buffer, but also
means we set a NULL pointer but non-zero length to the xdr scratch
buffer. This results in an oops the first time decoding needs to copy
something to scratch, which frequently happens when decoding READ_PLUS
hole segments.
I fix this by moving scratch handling into the pageio read code. I
provide a function to allocate scratch space for decoding read replies,
and free the scratch buffer when the nfs_pgio_header is freed.
Fixes: fbd2a05f29 (NFSv4.2: Rework scratch handling for READ_PLUS)
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
