commit 8c7d4b7b3d upstream.
This patch corrects the condition to kick the transfer without
giving back the requests when either request has remaining data
or when there are pending SGs. The && check was introduced during
spliting up the dwc3_gadget_ep_cleanup_completed_requests() function.
Fixes: f38e35dd84 ("usb: dwc3: gadget: split dwc3_gadget_ep_cleanup_completed_requests()")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69c7f4618c upstream.
Any write with either dd or flashcp to a device driven by the
spear_smi.c driver will pass through the spear_smi_cpy_toio()
function. This function will get called for chunks of up to 256 bytes.
If the amount of data is smaller, we may have a problem if the data
length is not 4-byte aligned. In this situation, the kernel panics
during the memcpy:
# dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
[...]
PC is at memcpy+0xcc/0x330
The above error occurs because the implementation of memcpy_toio()
tries to optimize the number of I/O by writing 4 bytes at a time as
much as possible, until there are less than 4 bytes left and then
switches to word or byte writes.
Unfortunately, the specification states about the Write Burst mode:
"the next AHB Write request should point to the next
incremented address and should have the same size (byte,
half-word or word)"
This means ARM architecture implementation of memcpy_toio() cannot
reliably be used blindly here. Workaround this situation by update the
write path to stick to byte access when the burst length is not
multiple of 4.
Fixes: f18dbbb1bf ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19e6317d24 upstream.
The problem arises because our read() function grabs a lock of the
circular buffer, finds something of interest, then invokes copy_to_user()
straight from the buffer, which in turn takes mm->mmap_sem. In the same
time, the callback mon_bin_vma_fault() is invoked under mm->mmap_sem.
It attempts to take the fetch lock and deadlocks.
This patch does away with protecting of our page list with any
semaphores, and instead relies on the kernel not close the device
while mmap is active in a process.
In addition, we prohibit re-sizing of a buffer while mmap is active.
This way, when (now unlocked) fault is processed, it works with the
page that is intended to be mapped-in, and not some other random page.
Note that this may have an ABI impact, but hopefully no legitimate
program is this wrong.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Reported-by: syzbot+56f9673bb4cdcbeb0e92@syzkaller.appspotmail.com
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 46eb14a6e1 ("USB: fix usbmon BUG trigger")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191204203941.3503452b@suzdal.zaitcev.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c11c4bed0 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 03270634e2 ("USB: Add ADU support for Ontrak ADU devices")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c5a2df336 upstream.
Make sure to use the current alternate setting when looking up the
endpoints on epic devices to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Cc: stable <stable@vger.kernel.org> # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09068c1ad5 upstream.
Make sure that the interrupt interface has an endpoint before trying to
access its endpoint descriptors to avoid dereferencing a NULL pointer.
The driver binds to the interrupt interface with interface number 0, but
must not assume that this interface or its current alternate setting are
the first entries in the corresponding configuration arrays.
Fixes: b72458a80c ("[PATCH] USB: Eagle and ADI 930 usb adsl modem driver")
Cc: stable <stable@vger.kernel.org> # 2.6.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210112601.3561-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53eaa9c27f upstream.
Temperature should be reported in milli-degrees, not degrees. Fix
scale and offset values to use the correct unit.
This is a fix for an issue that has been present for a long time.
The fixes tag reflects the point at which the code last changed in a
fashion that would make this fix patch no longer apply. Backports
will be necessary to fix those elements that predate that patch.
Fixes: 1615fe41a1 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: stable@vger.kernel.org
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c35b7a51e upstream.
The driver is defining debugfs entries by calling
`adis16480_debugfs_init()`. However, those entries are attached to the
iio_dev debugfs entry which won't exist if no debugfs_reg_access
callback is provided.
Fixes: 2f3abe6cbb ("iio:imu: Add support for the ADIS16480 and similar IMUs")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f9007d692 upstream.
Since v4.7 the dma initialization requires that there is a
device tree property for "rx" and "tx" channels which is
not provided by the pdata-quirks initialization.
By conversion of the mmc3 setup to device tree this will
finally allows to remove the OpenPandora wlan specific omap3
data-quirks.
Fixes: 81eef6ca92 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: <stable@vger.kernel.org> # v4.7+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ff1116280 upstream.
xhci driver claims it needs XHCI_TRUST_TX_LENGTH quirk for both
Broadcom/Cavium and a Renesas xHC controllers.
The quirk was inteded for handling false "success" complete event for
transfers that had data left untransferred.
These transfers should complete with "short packet" events instead.
In these two new cases the false "success" completion is reported
after a "short packet" if the TD consists of several TRBs.
xHCI specs 4.10.1.1.2 say remaining TRBs should report "short packet"
as well after the first short packet in a TD, but this issue seems so
common it doesn't make sense to add the quirk for all vendors.
Turn these events into short packets automatically instead.
This gets rid of the "The WARN Successful completion on short TX for
slot 1 ep 1: needs XHCI_TRUST_TX_LENGTH quirk" warning in many cases.
Cc: <stable@vger.kernel.org>
Reported-by: Eli Billauer <eli.billauer@gmail.com>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Eli Billauer <eli.billauer@gmail.com>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191211142007.8847-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c724f776f0 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 2865d42c78 ("staging: r8712u: Add the new driver to the mainline kernel")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210114751.5119-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74ca34118a upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: c2478d3907 ("staging: r8188eu: Add files for new driver - part 20")
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191210114751.5119-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e76b3bf765 upstream.
On Dell WD15 dock, sometimes USB ethernet cannot be detected after plugging
cable to the ethernet port, the hub and roothub get runtime resumed and
runtime suspended immediately:
...
[ 433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.315204] usb usb4: usb auto-resume
[ 433.315226] hub 4-0:1.0: hub_resume
[ 433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343
[ 433.315264] usb usb4-port1: status 0343 change 0001
[ 433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2
[ 433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0
[ 433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422307] usb usb4-port1: do warm reset
[ 433.422311] usb 4-1: device reset not allowed in state 8
[ 433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
[ 433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
[ 433.422356] usb usb4-port1: do warm reset
[ 433.422358] usb 4-1: device reset not allowed in state 8
[ 433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status = 0xf0002e2
[ 433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status = 0xe0002a0
[ 433.422465] hub 4-0:1.0: hub_suspend
[ 433.422475] usb usb4: bus auto-suspend, wakeup 1
[ 433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
[ 433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling.
[ 433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0
[ 433.862445] xhci_hcd 0000:3a:00.0: PME# enabled
[ 433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20)
[ 433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403)
[ 433.902490] xhci_hcd 0000:3a:00.0: PME# disabled
[ 433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering
[ 433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
[ 433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt!
[ 433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2
[ 433.902842] xhci_hcd 0000:3a:00.0: resume root hub
[ 433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling.
[ 433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling.
[ 433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
[ 433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
[ 433.902919] usb usb4: usb wakeup-resume
[ 433.902942] usb usb4: usb auto-resume
[ 433.902966] hub 4-0:1.0: hub_resume
...
As Mathias pointed out, the hub enters Cold Attach Status state and
requires a warm reset. However usb_reset_device() bails out early when
the device is in suspended state, as its callers port_event() and
hub_event() don't always resume the device.
Since there's nothing wrong to reset a suspended device, allow
usb_reset_device() to do so to solve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191106062710.29880-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4adc0423de upstream.
v4l2_compat_ioctl32() is the function that calls into
v4l2_file_operations->compat_ioctl32(), so setting that back to the same
function leads to a trivial endless loop, followed by a kernel
stack overrun.
Remove the incorrect assignment.
Cc: stable@vger.kernel.org
Fixes: 7472c1c691 ("[media] media: venus: vdec: add video decoder files")
Fixes: aaaa93eda6 ("[media] media: venus: venc: add video encoder files")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c93ad1337a upstream.
If register_snap_client fails in atalk_init,
error code should be set, otherwise it will
triggers NULL pointer dereference while unloading
module.
Fixes: 9804501fa1 ("appletalk: Fix potential NULL pointer dereference in unregister_snap_client")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9804501fa1 upstream.
register_snap_client may return NULL, all the callers
check it, but only print a warning. This will result in
NULL pointer dereference in unregister_snap_client and other
places.
It has always been used like this since v2.6
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a21b7f0cff upstream.
In qrtr_tun_write_iter the allocated kbuf should be release in case of
error or success return.
v2 Update: Thanks to David Miller for pointing out the release on success
path as well.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7aea8a9d71 upstream.
Renesas sound device has many IPs and many situations.
If platform/board uses MIXer, situation will be more complex.
To avoid duplicate DVC kctrl registration when MIXer was used,
it had original flags.
But it was issue when sound card was re-binded, because
no one can't cleanup this flags then.
To solve this issue, commit 9c698e8481 ("ASoC: rsnd: tidyup
registering method for rsnd_kctrl_new()") checks registered
card->controls, because if card was re-binded, these were cleanuped
automatically. This patch could solve re-binding issue.
But, it start to avoid MIX kctrl.
To solve these issues, we need below.
To avoid card re-binding issue: check registered card->controls
To avoid duplicate DVC registration: check registered rsnd_kctrl_cfg
To allow multiple MIX registration: check registered rsnd_kctrl_cfg
This patch do it.
Fixes: 9c698e8481 ("ASoC: rsnd: tidyup registering method for rsnd_kctrl_new()")
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-By: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1749d1ea89 upstream.
xfs_prepare_shift() fails to check the error return from
xfs_flush_unmap_range(). If the latter fails, that could lead to an
insert/collapse range operation over a delalloc range, which is not
supported.
Add an error check and return appropriately. This is reproduced
rarely by generic/475.
Fixes: 7f9f71be84 ("xfs: extent shifting doesn't fully invalidate page cache")
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Allison Collins <allison.henderson@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f67b5adc0 ]
In commit 4721a60109, we tried to fix a problem wherein directio reads
into a splice pipe will bounce EFAULT/EAGAIN all the way out to
userspace by simulating a zero-byte short read. This happens because
some directio read implementations (xfs) will call
bio_iov_iter_get_pages to grab pipe buffer pages and issue asynchronous
reads, but as soon as we run out of pipe buffers that _get_pages call
returns EFAULT, which the splice code translates to EAGAIN and bounces
out to userspace.
In that commit, the iomap code catches the EFAULT and simulates a
zero-byte read, but that causes assertion errors on regular splice reads
because xfs doesn't allow short directio reads. This causes infinite
splice() loops and assertion failures on generic/095 on overlayfs
because xfs only permit total success or total failure of a directio
operation. The underlying issue in the pipe splice code has now been
fixed by changing the pipe splice loop to avoid avoid reading more data
than there is space in the pipe.
Therefore, it's no longer necessary to simulate the short directio, so
remove the hack from iomap.
Fixes: 4721a60109 ("iomap: dio data corruption and spurious errors when pipes fill")
Reported-by: Murphy Zhou <jencce.kernel@gmail.com>
Ranted-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1761444557 ]
In commit 4721a60109, we tried to fix a problem wherein directio reads
into a splice pipe will bounce EFAULT/EAGAIN all the way out to
userspace by simulating a zero-byte short read. This happens because
some directio read implementations (xfs) will call
bio_iov_iter_get_pages to grab pipe buffer pages and issue asynchronous
reads, but as soon as we run out of pipe buffers that _get_pages call
returns EFAULT, which the splice code translates to EAGAIN and bounces
out to userspace.
In that commit, the iomap code catches the EFAULT and simulates a
zero-byte read, but that causes assertion errors on regular splice reads
because xfs doesn't allow short directio reads.
The brokenness is compounded by splice_direct_to_actor immediately
bailing on do_splice_to returning <= 0 without ever calling ->actor
(which empties out the pipe), so if userspace calls back we'll EFAULT
again on the full pipe, and nothing ever gets copied.
Therefore, teach splice_direct_to_actor to clamp its requests to the
amount of free space in the pipe and remove the simulated short read
from the iomap directio code.
Fixes: 4721a60109 ("iomap: dio data corruption and spurious errors when pipes fill")
Reported-by: Murphy Zhou <jencce.kernel@gmail.com>
Ranted-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c04571251b ]
The ast2600 no longer uses bit 4 in the control register to indicate a
1MHz clock (It now controls whether this watchdog is reset by a SOC
reset). This means we do not want to set it. It also does not need to be
set for the ast2500, as it is read-only on that SoC.
The comment next to the clock rate selection wandered away from where it
was set, so put it back next to the register setting it's describing.
Fixes: b3528b4874 ("watchdog: aspeed: Add support for AST2600")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20191108032905.22463-1-joel@jms.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3fc3f3d09 ]
The first argument to WARN() is supposed to be a condition. The
original code will just print the mdname() instead of the full warning
message.
Fixes: c84a1372df ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca58f55108 ]
This is an alternative fix attemp for the issue reported in the commit
caa8422d01 ("ALSA: hda: Flush interrupts on disabling") that was
reverted later due to regressions. Instead of tweaking the hardware
disablement order and the enforced irq flushing, do calling
cancel_work_sync() of the unsol work early enough, and explicitly
ignore the unsol events during the shutdown by checking the
bus->shutdown flag.
Fixes: caa8422d01 ("ALSA: hda: Flush interrupts on disabling")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://lore.kernel.org/r/s5h1ruxt9cz.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2a9edd056e upstream.
The old loop wouldn't stop when reaching `start` if `start==NULL`, instead
continuing backwards to index -1 and crashing.
Luckily you need to be highly privileged to map things at NULL, so it's not
a big problem.
Fix it by adjusting the loop so that the loop variable is always in bounds.
This patch is deliberately minimal to simplify backporting, but IMO this
function could use a refactor. The jump labels in the second loop body are
horrible (the error gotos should be jumping to free_range instead), and
both loops would look nicer if they just iterated upwards through indices.
And the up_read()+mmput() shouldn't be duplicated like that.
Cc: stable@vger.kernel.org
Fixes: 457b9a6f09 ("Staging: android: add binder driver")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191018205631.248274-3-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8eb52a1ee3 upstream.
binder_alloc_print_pages() iterates over
alloc->pages[0..alloc->buffer_size-1] under alloc->mutex.
binder_alloc_mmap_handler() writes alloc->pages and alloc->buffer_size
without holding that lock, and even writes them before the last bailout
point.
Unfortunately we can't take the alloc->mutex in the ->mmap() handler
because mmap_sem can be taken while alloc->mutex is held.
So instead, we have to locklessly check whether the binder_alloc has been
fully initialized with binder_alloc_get_vma(), like in
binder_alloc_new_buf_locked().
Fixes: 8ef4665aa1 ("android: binder: Add page usage in binder stats")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191018205631.248274-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
