commit ddf75be47c upstream
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae4 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e42404fa10 ]
To start stack unwinding (SP, PC and BLINK) are needed. When the
explicit execution context (pt_regs etc) is not available, unwinder
assumes the task is sleeping (in __switch_to()) and fetches SP and BLINK
from kernel mode stack.
But this assumption is not true, specially in a SMP system, when top
runs on 1 core, there may be active running processes on all cores.
So when unwinding non courrent tasks, ensure they are NOT running.
And while at it, handle the self unwinding case explicitly.
This came out of investigation of a customer reported hang with
rcutorture+top
Link: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/31
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04516706bb ]
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d853b34069 ]
Clang warns:
drivers/spi/spi-bcm2835aux.c:532:50: warning: variable 'err' is
uninitialized when used here [-Wuninitialized]
dev_err(&pdev->dev, "could not get clk: %d\n", err);
^~~
./include/linux/dev_printk.h:112:32: note: expanded from macro 'dev_err'
_dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
drivers/spi/spi-bcm2835aux.c:495:9: note: initialize the variable 'err'
to silence this warning
int err;
^
= 0
1 warning generated.
Restore the assignment so that the error value can be used in the
dev_err statement and there is no uninitialized memory being leaked.
Fixes: e13ee6cc47 ("spi: bcm2835aux: Fix use-after-free on unbind")
Link: https://github.com/ClangBuiltLinux/linux/issues/1199
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113180701.455541-1-natechancellor@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
[lukas: backport to 4.19-stable, add stable designation]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.4+: e13ee6cc47: spi: bcm2835aux: Fix use-after-free on unbind
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 778721510e upstream.
If gfs2 tries to mount a (corrupt) file system that has no resource
groups it still tries to set preferences on the first one, which causes
a kernel null pointer dereference. This patch adds a check to function
gfs2_ri_update so this condition is detected and reported back as an
error.
Reported-by: syzbot+e3f23ce40269a4c9053a@syzkaller.appspotmail.com
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcee527895 upstream.
When the instances were able to use their own options, the userstacktrace
option was left hardcoded for the top level. This made the instance
userstacktrace option bascially into a nop, and will confuse users that set
it, but nothing happens (I was confused when it happened to me!)
Cc: stable@vger.kernel.org
Fixes: 16270145ce ("tracing: Add trace options for core options to instances")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63c5395bb7 ]
bcm_qspi_remove() calls spi_unregister_master() even though
bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is
therefore unregistered and freed twice on unbind.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
While at it, fix an ordering issue in bcm_qspi_remove() wherein
spi_unregister_master() is called after uninitializing the hardware,
disabling the clock and freeing an IRQ data structure. The correct
order is to call spi_unregister_master() *before* those teardown steps
because bus accesses may still be ongoing until that function returns.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <stable@vger.kernel.org> # v4.9+: 5e844cc37a: spi: Introduce device-managed SPI controller allocation
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/5e31a9a59fd1c0d0b795b2fe219f25e5ee855f9d.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e844cc37a ]
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_master()
spi_unregister_master()
That's because spi_unregister_master() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_master which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_master struct. Thus, once spi_unregister_master() has been
called, the private data is inaccessible. But some drivers need to
access it after spi_unregister_master() to perform further teardown
steps.
Introduce devm_spi_alloc_master(), which releases a reference on the
spi_master struct only after the driver has unbound, thereby keeping the
memory allocation accessible. Change spi_unregister_master() to not
release a reference if the spi_master was allocated by the new devm
function.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_master in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm function
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the master.
That commit shall amend spi_unregister_master() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/272bae2ef08abd21388c98e23729886663d19192.1605121038.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1de67a3dee upstream.
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a9565f7 upstream.
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c75b0ff4e upstream.
On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in
ftrace_get_addr_new() followed by the below message:
Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001)
The set of steps leading to this involved:
- modprobe ftrace-direct-too
- enable_probe
- modprobe ftrace-direct
- rmmod ftrace-direct <-- trigger
The problem turned out to be that we were not updating flags in the
ftrace record properly. From the above message about the trampoline
accounting being bad, it can be seen that the ftrace record still has
FTRACE_FL_TRAMP set though ftrace-direct module is going away. This
happens because we are checking if any ftrace_ops has the
FTRACE_FL_TRAMP flag set _before_ updating the filter hash.
The fix for this is to look for any _other_ ftrace_ops that also needs
FTRACE_FL_TRAMP.
Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com
Cc: stable@vger.kernel.org
Fixes: a124692b69 ("ftrace: Enable trampoline when rec count returns back to one")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8bcd9c5be upstream.
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242d990c15 upstream.
The generic parser accepts the preferred_dacs[] pairs as a hint for
assigning a DAC to each pin, but this hint doesn't work always
effectively. Currently it's merely a secondary choice after the trial
with the path index failed. This made sometimes it difficult to
assign DACs without mimicking the connection list and/or the badness
table.
This patch adds a new flag, obey_preferred_dacs, that changes the
behavior of the parser. As its name stands, the parser obeys the
given preferred_dacs[] pairs by skipping the path index matching and
giving a high penalty if no DAC is assigned by the pairs. This mode
will help for assigning the fixed DACs forcibly from the codec
driver.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201127141104.11041-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ffccbf05 upstream.
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bb ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 469aceddfa ]
Toshiaki pointed out that we now have two very similar functions to extract
the L3 protocol number in the presence of VLAN tags. And Daniel pointed out
that the unbounded parsing loop makes it possible for maliciously crafted
packets to loop through potentially hundreds of tags.
Fix both of these issues by consolidating the two parsing functions and
limiting the VLAN tag parsing to a max depth of 8 tags. As part of this,
switch over __vlan_get_protocol() to use skb_header_pointer() instead of
pskb_may_pull(), to avoid the possible side effects of the latter and keep
the skb pointer 'const' through all the parsing functions.
v2:
- Use limit of 8 tags instead of 32 (matching XMIT_RECURSION_LIMIT)
Reported-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: d7bf2ebebc ("sched: consistently handle layer3 header accesses in the presence of VLANs")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 156abe2961 upstream
The pins on the Bay Trail SoC have separate input-buffer and output-buffer
enable bits and a read of the level bit of the value register will always
return the value from the input-buffer.
The BIOS of a device may configure a pin in output-only mode, only enabling
the output buffer, and write 1 to the level bit to drive the pin high.
This 1 written to the level bit will be stored inside the data-latch of the
output buffer.
But a subsequent read of the value register will return 0 for the level bit
because the input-buffer is disabled. This causes a read-modify-write as
done by byt_gpio_set_direction() to write 0 to the level bit, driving the
pin low!
Before this commit byt_gpio_direction_output() relied on
pinctrl_gpio_direction_output() to set the direction, followed by a call
to byt_gpio_set() to apply the selected value. This causes the pin to
go low between the pinctrl_gpio_direction_output() and byt_gpio_set()
calls.
Change byt_gpio_direction_output() to directly make the register
modifications itself instead. Replacing the 2 subsequent writes to the
value register with a single write.
Note that the pinctrl code does not keep track internally of the direction,
so not going through pinctrl_gpio_direction_output() is not an issue.
This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is
already on at boot (no external monitor connected), then the i915 driver
does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The
temporarily going low of that GPIO was causing the panel to reset itself
after which it would not show an image until it was turned off and back on
again (until a full modeset was done on it). This commit fixes this.
This commit also updates the byt_gpio_direction_input() to use direct
register accesses instead of going through pinctrl_gpio_direction_input(),
to keep it consistent with byt_gpio_direction_output().
Note for backporting, this commit depends on:
commit e2b74419e5 ("pinctrl: baytrail: Replace WARN with dev_info_once
when setting direct-irq pin to output")
Cc: stable@vger.kernel.org
Fixes: 86e3ef812f ("pinctrl: baytrail: Update gpio chip operations")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[sudip: use byt_gpio and vg->pdev->dev for dev_info()]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2b74419e5 upstream
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI
resource so we can do this without problems as long as we release the
IRQ before changing the pin to output mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource. This
works fine, but this triggers the WARN in byt_gpio_set_direction-s output
path because direct-irq support is enabled on the pin.
This commit replaces the WARN call with a dev_info_once call, fixing a
bunch of WARN splats in dmesg on each suspend/resume cycle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ed381439e upstream.
i40iw_mmap manipulates the vma->vm_pgoff to differentiate a push page mmap
vs a doorbell mmap, and uses it to compute the pfn in remap_pfn_range
without any validation. This is vulnerable to an mmap exploit as described
in: https://lore.kernel.org/r/20201119093523.7588-1-zhudi21@huawei.com
The push feature is disabled in the driver currently and therefore no push
mmaps are issued from user-space. The feature does not work as expected in
the x722 product.
Remove the push module parameter and all VMA attribute manipulations for
this feature in i40iw_mmap. Update i40iw_mmap to only allow DB user
mmapings at offset = 0. Check vm_pgoff for zero and if the mmaps are bound
to a single page.
Cc: <stable@kernel.org>
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Link: https://lore.kernel.org/r/20201125005616.1800-2-shiraz.saleem@intel.com
Reported-by: Di Zhu <zhudi21@huawei.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c7e41e1caa sought to backport upstream commit 84855678ad to
the 4.9-stable tree but erroneously inserted a line at the wrong place.
Fix it.
Fixes: c7e41e1caa ("spi: Fix controller unregister order")
Reported-by: yangerkun <yangerkun@huawei.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
[ Upstream commit 4d521943f7 ]
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
Fixes: a1a8b4594f ("NFC: pn544: i2c: Add DTS Documentation")
Fixes: 6be88670fc ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Fixes: e3b3292215 ("dt-bindings: can: tcan4x5x: Update binding to use interrupt property")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for tcan4x5x.txt
Link: https://lore.kernel.org/r/20201026153620.89268-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d2bb5ad89 ]
When command interface is down, driver to reclaim all 4K page chucks that
were hold by the Firmeware. Fix a bug for 64K page size systems, where
driver repeatedly released only the first chunk of the page.
Define helper function to fill 4K chunks for a given Firmware pages.
Iterate over all unreleased Firmware pages and call the hepler per each.
Fixes: 5adff6a088 ("net/mlx5: Fix incorrect page count when in internal error")
Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ee50c8e26 ]
The .x25_addr[] address comes from the user and is not necessarily
NUL terminated. This leads to a couple problems. The first problem is
that the strlen() in x25_bind() can read beyond the end of the buffer.
The second problem is more subtle and could result in memory corruption.
The call tree is:
x25_connect()
--> x25_write_internal()
--> x25_addr_aton()
The .x25_addr[] buffers are copied to the "addresses" buffer from
x25_write_internal() so it will lead to stack corruption.
Verify that the strings are NUL terminated and return -EINVAL if they
are not.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Fixes: a9288525d2 ("X25: Dont let x25_bind use addresses containing characters")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/X8ZeAKm8FnFpN//B@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ba246c1751 ]
TX completions received with an error return code are not
being processed properly. When an error code is seen, do not
proceed to the next completion before cleaning up the existing
entry's data structures.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
