[ Upstream commit e3e56c050a ]
The general expectation is that powering on a power-domain should make
the power domain deliver some power, and if a specific performance state
is needed further requests has to be made.
But in contrast with other power-domain implementations (e.g. rpmpd) the
RPMh does not have an interface to enable the power, so the driver has
to vote for a particular corner (performance level) in rpmh_power_on().
But the corner is never initialized, so a typical request to simply
enable the power domain would not actually turn on the hardware. Further
more, when no more clients vote for a performance state (i.e. the
aggregated vote is 0) the power domain would be turned off.
Fix both of these issues by always voting for a corner with non-zero
value, when the power domain is enabled.
The tracking of the lowest non-zero corner is performed to handle the
corner case if there's ever a domain with a non-zero lowest corner, in
which case both rpmh_power_on() and rpmh_rpmhpd_set_performance_state()
would be allowed to use this lowest corner.
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211005033732.2284447-1-bjorn.andersson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f87a74d31 ]
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a0 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2012579b31 ]
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes: 76045bc457 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ab1891640 ]
Commit 723de0f917 ("staging: most: remove device from interface
structure") moved registration of driver-provided struct device to
the most subsystem.
Dim2 used to register the same struct device to provide a custom device
attribute. This causes double-registration of the same struct device.
Fix that by moving the custom attribute to driver's dev_groups.
This moves attribute to the platform_device object, which is a better
location for platform-specific attributes anyway.
Fixes: 723de0f917 ("staging: most: remove device from interface structure")
Acked-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Link: https://lore.kernel.org/r/20211011061117.21435-1-nikita.yoush@cogentembedded.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4875d509a ]
This variable is just a temporary variable, used to do an endian
conversion. The problem is that the last byte is not initialized. After
the conversion is completely done, the last byte is discarded so it doesn't
cause a problem. But static checkers and the KMSan runtime checker can
detect the uninitialized read and will complain about it.
Link: https://lore.kernel.org/r/20211006073242.GA8404@kili
Fixes: 5036f0a0ec ("[SCSI] csiostor: Fix sparse warnings.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9583922563 ]
Commit a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path
check") added is_kvm_guest() and changed kvm_para_available() to use it.
is_kvm_guest() checks a static key, kvm_guest, and that static key is
set in check_kvm_guest().
The problem is check_kvm_guest() is only called on pseries, and even
then only in some configurations. That means is_kvm_guest() always
returns false on all non-pseries and some pseries depending on
configuration. That's a bug.
For PR KVM guests this is noticable because they no longer do live
patching of themselves, which can be detected by the omission of a
message in dmesg such as:
KVM: Live patching for a fast VM worked
To fix it make check_kvm_guest() an initcall, to ensure it's always
called at boot. It needs to be core so that it runs before
kvm_guest_init() which is postcore. To be an initcall it needs to return
int, where 0 means success, so update that.
We still call it manually in pSeries_smp_probe(), because that runs
before init calls are run.
Fixes: a21d1becaa ("powerpc: Reintroduce is_kvm_guest() as a fast-path check")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210623130514.2543232-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2719b26ae ]
While investigating a lockup at startup on Powerbook 3400C, it was
identified that the fbdev driver generates alignment exception at
startup:
--- interrupt: 600 at memset+0x60/0xc0
NIP: c0021414 LR: c03fc49c CTR: 00007fff
REGS: ca021c10 TRAP: 0600 Tainted: G W (5.14.2-pmac-00727-g12a41fa69492)
MSR: 00009032 <EE,ME,IR,DR,RI> CR: 44008442 XER: 20000100
DAR: cab80020 DSISR: 00017c07
GPR00: 00000007 ca021cd0 c14412e0 cab80000 00000000 00100000 cab8001c 00000004
GPR08: 00100000 00007fff 00000000 00000000 84008442 00000000 c0006fb4 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00100000
GPR24: 00000000 81800000 00000320 c15fa400 c14d1878 00000000 c14d1800 c094e19c
NIP [c0021414] memset+0x60/0xc0
LR [c03fc49c] chipsfb_pci_init+0x160/0x580
--- interrupt: 600
[ca021cd0] [c03fc46c] chipsfb_pci_init+0x130/0x580 (unreliable)
[ca021d20] [c03a3a70] pci_device_probe+0xf8/0x1b8
[ca021d50] [c043d584] really_probe.part.0+0xac/0x388
[ca021d70] [c043d914] __driver_probe_device+0xb4/0x170
[ca021d90] [c043da18] driver_probe_device+0x48/0x144
[ca021dc0] [c043e318] __driver_attach+0x11c/0x1c4
[ca021de0] [c043ad30] bus_for_each_dev+0x88/0xf0
[ca021e10] [c043c724] bus_add_driver+0x190/0x22c
[ca021e40] [c043ee94] driver_register+0x9c/0x170
[ca021e60] [c0006c28] do_one_initcall+0x54/0x1ec
[ca021ed0] [c08246e4] kernel_init_freeable+0x1c0/0x270
[ca021f10] [c0006fdc] kernel_init+0x28/0x11c
[ca021f30] [c0017148] ret_from_kernel_thread+0x14/0x1c
Instruction dump:
7d4601a4 39490777 7d4701a4 39490888 7d4801a4 39490999 7d4901a4 39290aaa
7d2a01a4 4c00012c 4bfffe88 0fe00000 <4bfffe80> 9421fff0 38210010 48001970
This is due to 'dcbz' instruction being used on non-cached memory.
'dcbz' instruction is used by memset() to zeroize a complete
cacheline at once, and memset() is not expected to be used on non
cached memory.
When performing a 'sparse' check on fbdev driver, it also appears
that the use of memset() is unexpected:
drivers/video/fbdev/chipsfb.c:334:17: warning: incorrect type in argument 1 (different address spaces)
drivers/video/fbdev/chipsfb.c:334:17: expected void *
drivers/video/fbdev/chipsfb.c:334:17: got char [noderef] __iomem *screen_base
drivers/video/fbdev/chipsfb.c:334:15: warning: memset with byte count of 1048576
Use fb_memset() instead of memset(). fb_memset() is defined as
memset_io() for powerpc.
Fixes: 8c8709334c ("[PATCH] ppc32: Remove CONFIG_PMAC_PBOOK")
Reported-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/884a54f1e5cb774c1d9b4db780209bee5d4f6718.1631712563.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ed2f3545c ]
The error handling code of fsl_ifc_ctrl_probe is problematic. When
fsl_ifc_ctrl_init fails or request_irq of fsl_ifc_ctrl_dev->irq fails,
it forgets to free the irq and nand_irq. Meanwhile, if request_irq of
fsl_ifc_ctrl_dev->nand_irq fails, it will still free nand_irq even if
the request_irq is not successful.
Fix this by refactoring the error handling code.
Fixes: d2ae2e20fb ("driver/memory:Move Freescale IFC driver to a common driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210925151434.8170-1-mudongliangabcd@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 986b509470 ]
If an error occurs after a successful tegra_powergate_enable_clocks()
call, it must be undone by a tegra_powergate_disable_clocks() call, as
already done in the below and above error handling paths of this function.
Update the 'goto' to branch at the correct place of the error handling
path.
Fixes: a38045121b ("soc/tegra: pmc: Add generic PM domain support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884ea75d79 ]
Fix typo in pinctrl. It did only work because the bootloader
seems to have initialized it.
Fixes: ee32711195 ("ARM: dts: omap3-gta04: Define and use bma180 irq pin")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df0a181494 ]
I got memory leak as follows:
unreferenced object 0xffff88801f0b2200 (size 64):
comm "i2c-lis2hh12-21", pid 5455, jiffies 4294944606 (age 15.224s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 3a 72 65 67 75 6c 61 regulator:regula
74 6f 72 2e 30 2d 2d 69 32 63 3a 31 2d 30 30 31 tor.0--i2c:1-001
backtrace:
[<00000000bf5b0c3b>] __kmalloc_track_caller+0x19f/0x3a0
[<0000000050da42d9>] kvasprintf+0xb5/0x150
[<000000004bbbed13>] kvasprintf_const+0x60/0x190
[<00000000cdac7480>] kobject_set_name_vargs+0x56/0x150
[<00000000bf83f8e8>] dev_set_name+0xc0/0x100
[<00000000cc1cf7e3>] device_link_add+0x6b4/0x17c0
[<000000009db9faed>] _regulator_get+0x297/0x680
[<00000000845e7f2b>] _devm_regulator_get+0x5b/0xe0
[<000000003958ee25>] st_sensors_power_enable+0x71/0x1b0 [st_sensors]
[<000000005f450f52>] st_accel_i2c_probe+0xd9/0x150 [st_accel_i2c]
[<00000000b5f2ab33>] i2c_device_probe+0x4d8/0xbe0
[<0000000070fb977b>] really_probe+0x299/0xc30
[<0000000088e226ce>] __driver_probe_device+0x357/0x500
[<00000000c21dda32>] driver_probe_device+0x4e/0x140
[<000000004e650441>] __device_attach_driver+0x257/0x340
[<00000000cf1891b8>] bus_for_each_drv+0x166/0x1e0
When device_register() returns an error, the name allocated in dev_set_name()
will be leaked, the put_device() should be used instead of kfree() to give up
the device reference, then the name will be freed in kobject_cleanup() and the
references of consumer and supplier will be decreased in device_link_release_fn().
Fixes: 287905e68d ("driver core: Expose device link details in sysfs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210930085714.2057460-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4ca3871e2 ]
The commit f87e7f2589 ("ALSA: hda - Improved position reporting on
SKL+") changed the PCM position report for SKL+ chips to use DPIB, but
according to Pierre, DPIB is no best choice for the accurate position
reports and it often reports too early. The recommended method is
rather the classical position buffer.
This patch makes the PCM position reporting on SKL+ back to the
position buffer again.
Fixes: f87e7f2589 ("ALSA: hda - Improved position reporting on SKL+")
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210929072934.6809-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 472e18f63c ]
Make sure the HDA driver's display power reference is released during
shutdown/reboot.
During the shutdown/reboot sequence the pci device core calls the
pm_runtime_resume handler for all devices before calling the driver's
shutdown callback and so the HDA driver's runtime resume callback will
acquire a display power reference (on HSW/BDW). This triggers a power
reference held WARN on HSW/BDW in the i915 driver's subsequent shutdown
handler, which expects all display power references to be released by
that time.
Since the HDA controller is stopped in the shutdown handler in any case,
let's follow here the same sequence as the one during runtime suspend.
This will also reset the HDA link and drop the display power reference,
getting rid of the above WARN.
Tested on HSW.
v2:
- Fix the build for CONFIG_PM=n (Takashi)
- s/__azx_runtime_suspend/azx_shutdown_chip/
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3618
References: https://lore.kernel.org/lkml/cea1f9a-52e0-b83-593d-52997fe1aaf6@er-systems.de
Reported-and-tested-by: Thomas Voegtle <tv@lio96.de>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20210623134601.2128663-1-imre.deak@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46243b85b0 ]
The position reporting on Intel Skylake and later chips via
azx_get_pos_skl() contains a udelay(20) call for the capture streams.
A call for this alone doesn't sound too harmful. However, as the
pointer PCM ops is one of the hottest path in the PCM operations --
especially for the timer-scheduled operations like PulseAudio -- such
a delay hogs CPU usage significantly in the total performance.
The code there was taken from the original code in ASoC SST Skylake
driver blindly. The udelay() is a workaround for the case where the
reported position is behind the period boundary at the timing
triggered from interrupts; applications often expect that the full
data is available for the whole period when returned (and also that's
the definition of the ALSA PCM period).
OTOH, HD-audio (legacy) driver has already some workarounds for the
delayed position reporting due to its relatively large FIFO, such as
the BDL position adjustment and the delayed period-elapsed call in the
work. That said, the udelay() is almost superfluous for HD-audio
driver unlike SST, and we can drop the udelay().
Though, the current code doesn't guarantee the full period readiness
as mentioned in the above, but rather it checks the wallclock and
detects the unexpected jump. That's one missing piece, and the drop
of udelay() needs a bit more sanity checks for the delayed handling.
This patch implements those: the drop of udelay() call in
azx_get_pos_skl() and the more proper check of hwptr in
azx_position_ok(). The latter change is applied only for the case
where the stream is running in the normal mode without
no_period_wakeup flag. When no_period_wakeup is set, it essentially
ignores the period handling and rather concentrates only on the
current position; which implies that we don't need to care about the
period boundary at all.
Fixes: f87e7f2589 ("ALSA: hda - Improved position reporting on SKL+")
Reported-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210929072934.6809-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 483de2b44c ]
While removing the size from the "reg" properties in pm8916.dtsi,
commit bd6429e810 ("ARM64: dts: qcom: Remove size elements from
pmic reg properties") mistakenly also removed the second register
address for the rtc@6000 device. That one did not represent the size
of the register region but actually the address of the second "alarm"
register region of the rtc@6000 device.
Now there are "reg-names" for two "reg" elements, but there is actually
only one "reg" listed.
Since the DT schema for "qcom,pm8941-rtc" only expects one "reg"
element anyway, just drop the "reg-names" entirely to fix this.
Fixes: bd6429e810 ("ARM64: dts: qcom: Remove size elements from pmic reg properties")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-1-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8199a0b31e ]
At the moment, playing audio on Secondary MI2S will just end up getting
stuck, without actually playing any audio. This happens because the wrong
bit clock is configured when playing audio on Secondary MI2S.
The PRI_I2S_CLK (better name: SPKR_I2S_CLK) is used by the SPKR audio mux
block that provides both Primary and Secondary MI2S.
The SEC_I2S_CLK (better name: MIC_I2S_CLK) is used by the MIC audio mux
block that provides Tertiary MI2S. Quaternary MI2S is also part of the
MIC audio mux but has its own clock (AUX_I2S_CLK).
This means that (quite confusingly) the SEC_I2S_CLK is not actually
used for Secondary MI2S as the name would suggest. Secondary MI2S
needs to have the same clock as Primary MI2S configured.
Fix the clock list for the lpass node in the device tree and add
a comment to clarify this confusing naming. With these changes,
audio can be played correctly on Secondary MI2S.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 3761a3618f ("arm64: dts: qcom: add lpass node")
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816181810.2242-1-stephan@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c48a14dca2 ]
In jfs_mount, when diMount(ipaimap2) fails, it goes to errout35. However,
the following code does not free ipaimap2 allocated by diReadSpecial.
Fix this by refactoring the error handling code of jfs_mount. To be
specific, modify the lable name and free ipaimap2 when the above error
ocurrs.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f3b3c2bfa ]
mach/loongson64 fails to build when the FPU support is disabled:
arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration]
arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’
Fixes: ef2f826c8f ("MIPS: Loongson-3: Enable the COP2 usage")
Suggested-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reported-by: k2ci robot <kernel-bot@kylinos.cn>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3e9431854 ]
On resume we can get a warning at kernel/time/timekeeping.c:824 for
timekeeping_suspended.
Let's fix this by adding separate functions for sysc_poll_reset_sysstatus()
and sysc_poll_reset_sysconfig() and have the new functions handle also
timekeeping_suspended.
If iopoll at some point supports timekeeping_suspended, we can just drop
the custom handling from these functions.
Fixes: d46f9fbec7 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f46633565 ]
commit 4e5833884f ("arm64: dts: ti: k3-j721e-main: Add PCIe device
tree nodes") restricted PCIe bus numbers from 0 to 15 (due to SMMU
restriction in J721E). However since SMMU is not enabled, allow the full
supported bus numbers from 0 to 255.
Fixes: 4e5833884f ("arm64: dts: ti: k3-j721e-main: Add PCIe device tree nodes")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210915055358.19997-3-kishon@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
