Currently cfg80211 checks for invalid channels whenever there is a
regulatory update and stops the active interfaces if it is operating on
an unsupported channel in the new regulatory domain.
This is done based on a regulatory flag REGULATORY_IGNORE_STALE_KICKOFF
set during wiphy registration which disables this enforcement when
unsupported interface modes are supported by driver.
Add support to enable this enforcement when Mesh Point interface type
is advertised by drivers.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1638409120-28997-1-git-send-email-quic_srirrama@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
iwlwifi needs to be able to differentiate between the
software rfkill state and the hardware rfkill state.
The reason for this is that iwlwifi needs to notify any
change in the software rfkill state even when it doesn't
own the device (which means even when the hardware rfkill
is asserted).
In order to be able to know the software rfkill when the
host does not own the device, iwlwifi needs to be able to
ask the state of the software rfkill ignoring the state
of the hardware rfkill.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20211219195124.125689-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fixed counter 3 is used for the Topdown metrics, which hasn't been
enabled for KVM guests. Userspace accessing to it will fail as it's not
included in get_fixed_pmc(). This breaks KVM selftests on ICX+ machines,
which have this counter.
To reproduce it on ICX+ machines, ./state_test reports:
==== Test Assertion Failure ====
lib/x86_64/processor.c:1078: r == nmsrs
pid=4564 tid=4564 - Argument list too long
1 0x000000000040b1b9: vcpu_save_state at processor.c:1077
2 0x0000000000402478: main at state_test.c:209 (discriminator 6)
3 0x00007fbe21ed5f92: ?? ??:0
4 0x000000000040264d: _start at ??:?
Unexpected result from KVM_GET_MSRS, r: 17 (failed MSR was 0x30c)
With this patch, it works well.
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Message-Id: <20211217124934.32893-1-wei.w.wang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a flag attribute to use in ap settings to indicate userspace
supports offloading of SA Query procedures to driver. Also add AP SME
device feature flag to advertise that the SA Query procedures offloaded
to driver when userspace indicates support for offloading of SA Query
procedures.
Driver handles SA Query procedures in driver's SME it self and skip
sending SA Query request or response frames to userspace when userspace
indicates support for SA Query procedures offload. But if userspace
doesn't advertise support for SA Query procedures offload driver shall
not offload SA Query procedures handling.
Also userspace with SA Query procedures offload capability shall skip SA
Query specific validations when driver indicates support for handling SA
Query procedures.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/1637911519-21306-2-git-send-email-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In previous method each AP settings flag is represented by a top-level
flag attribute and conversion to enum cfg80211_ap_settings_flags had to
be done before sending them to driver. This commit is to make it easier
to define new AP settings flags and sending them to driver.
This commit also deprecate sending of
%NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in %NL80211_CMD_START_AP. But to
maintain backwards compatibility checks for
%NL80211_ATTR_EXTERNAL_AUTH_SUPPORT in %NL80211_CMD_START_AP when
%NL80211_ATTR_AP_SETTINGS_FLAGS not present in %NL80211_CMD_START_AP.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/1637911519-21306-1-git-send-email-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI standard defines "Offchannel CAC" as:
"Off-Channel CAC is performed by a number of non-continuous checks
spread over a period in time. This period, which is required to
determine the presence of radar signals, is defined as the Off-Channel
CAC Time..
Minimum Off-Channel CAC Time 6 minutes and Maximum Off-Channel CAC Time
4 hours..".
mac80211 implementation refers to a dedicated hw chain used for continuous
radar monitoring. Rename offchannel_* references to background_* in
order to avoid confusion with ETSI standard.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/4204cc1d648d76b44557981713231e030a3bd991.1638190762.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time values used by the airtime fairness code only need to be accurate
enough to cover station activity detection.
Using ktime_get_coarse_boottime_ns instead of ktime_get_boottime_ns will
drop the accuracy down to jiffies intervals, but at the same time saves
a lot of CPU cycles in a hot path
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20211217114258.14619-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signal processor STORE STATUS requires a physical address where register
contents are supposed to be written to, however the kernel must read the
data via the corresponding virtual address.
Also the allocated save_area, where register contents are copied to,
resides in virtual address space.
Fix this by using proper __pa() conversion, or correct memblock_alloc()
invocation.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The clgfi instruction used within the ChaCha20 assembly is only
available for z9-109 and newer machines, and therefore this will
generate a compile error if compiled e.g. with MARCH_Z900.
Given that the assembler code will only be executed on machines with
vector instructions, which became much later available than z9-109,
use insn notation to generate the clgfi instruction, and avoid compile
errors due to unknown instructions.
Fixes: b087dfab4d ("s390/crypto: add SIMD implementation for ChaCha20")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
These two wrappers around their respective struct page variants will be
useful in the following patches.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Roman Gushchin <guro@fb.com>
Both __pkru_allows_write() and arch_set_user_pkey_access() shift
PKRU_WD_BIT (a signed constant) by up to 30 bits, hitting the
sign bit.
Use unsigned constants instead.
Clearly pkey 15 has not been used in combination with UBSAN yet.
Noticed by code inspection only. I can't actually provoke the
compiler into generating incorrect logic as far as this shift is
concerned.
[
dhansen: add stable@ tag, plus minor changelog massaging,
For anyone doing backports, these #defines were in
arch/x86/include/asm/pgtable.h before 784a46618f.
]
Fixes: 33a709b25a ("mm/gup, x86/mm/pkeys: Check VMAs and PTEs for protection keys")
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211216000856.4480-1-andrew.cooper3@citrix.com
Pull kvm fixes from Paolo Bonzini:
"Two small fixes, one of which was being worked around in selftests"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Retry page fault if MMU reload is pending and root has no sp
KVM: selftests: vmx_pmu_msrs_test: Drop tests mangling guest visible CPUIDs
KVM: x86: Drop guest CPUID check for host initiated writes to MSR_IA32_PERF_CAPABILITIES
Pull block revert from Jens Axboe:
"It turns out that the fix for not hammering on the delayed work timer
too much caused a performance regression for BFQ, so let's revert the
change for now.
I've got some ideas on how to fix it appropriately, but they should
wait for 5.17"
* tag 'block-5.16-2021-12-19' of git://git.kernel.dk/linux-block:
Revert "block: reduce kblockd_mod_delayed_work_on() CPU consumption"
Pull irq fixes from Borislav Petkov:
- Clear the PCI_MSIX_FLAGS_MASKALL bit too on the error path so that it
is restored to its reset state
- Mask MSI-X vectors late on the init path in order to handle
out-of-spec Marvell NVME devices which apparently look at the MSI-X
mask even when MSI-X is disabled
* tag 'irq_urgent_for_v5.16_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI/MSI: Clear PCI_MSIX_FLAGS_MASKALL on error
PCI/MSI: Mask MSI-X vectors only on success
Pull timer fix from Borislav Petkov:
- Make sure the CLOCK_REALTIME to CLOCK_MONOTONIC offset is never
positive
* tag 'timers_urgent_for_v5.16_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Really make sure wall_to_monotonic isn't positive
Pull locking fix from Borislav Petkov:
- Fix the rtmutex condition checking when the optimistic spinning of a
waiter needs to be terminated
* tag 'locking_urgent_for_v5.16_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Fix incorrect condition in rtmutex_spin_on_owner()
Pull signal handlign fix from Borislav Petkov:
- Prevent lock contention on the new sigaltstack lock on the
common-case path, when no changes have been made to the alternative
signal stack.
* tag 'core_urgent_for_v5.16_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
signal: Skip the altstack update when not needed
Pull MIPS fix from Thomas Bogendoerfer:
- only enable pci_remap_iospace() for Ralink devices
* tag 'mips-fixes_5.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Only define pci_remap_iospace() for Ralink
The current 'rx-internal-delay-ps' property value on the Realtek switch
node, 2000, will be divided by 300, resulting in 6.66, which will be
rounded to the closest step value, 7. Change it to 2100 to be accurate.
See ef136837aa ("net: dsa: rtl8365mb: set RGMII RX delay in steps of
0.3 ns") for reference.
Flow control needs to be enabled on both sides of the internal and
external switch. It is already enabled on the CPU port of the Realtek
switch so we also enable it on the external switch port of the Broadcom
switch as well.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pull powerpc fixes from Michael Ellerman:
"Fix a recently introduced oops at boot on 85xx in some configurations.
Fix crashes when loading some livepatch modules with
STRICT_MODULE_RWX.
Thanks to Joe Lawrence, Russell Currey, and Xiaoming Ni"
* tag 'powerpc-5.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/module_64: Fix livepatching for RO modules
powerpc/85xx: Fix oops when CONFIG_FSL_PMC=n
Pull cifs fixes from Steve French:
"Two cifs/smb3 fixes, one fscache related, and one mount parsing
related for stable"
* tag '5.16-rc5-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: sanitize multiple delimiters in prepath
cifs: ignore resource_id while getting fscache super cookie
Rename the SATA controller unit name from ahci to sata in preparation
for adding the Broadcom SATA3 controller YAML binding which will bring
validation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rename the msi controller unit name to 'msi' to avoid collisions with
the 'msi-controller' boolean property.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rename the msi controller unit name to 'msi' to avoid collisions with
the 'msi-controller' boolean property.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update the PCIe PHY node unit name and its sub-nodes to help with
upcoming changes converting the Cygnus PCIe PHY DT binding to YAML and
later the iProc PCIe controller binding to YAML.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Rename the msi controller unit name to 'msi' to avoid collisions with
the 'msi-controller' boolean property. We also need to re-arrange the
'ranges' property to show the two cells as being separate instead of
combined since the DT checker is not able to differentiate otherwise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Play nice with a NULL shadow page when checking for an obsolete root in
the page fault handler by flagging the page fault as stale if there's no
shadow page associated with the root and KVM_REQ_MMU_RELOAD is pending.
Invalidating memslots, which is the only case where _all_ roots need to
be reloaded, requests all vCPUs to reload their MMUs while holding
mmu_lock for lock.
The "special" roots, e.g. pae_root when KVM uses PAE paging, are not
backed by a shadow page. Running with TDP disabled or with nested NPT
explodes spectaculary due to dereferencing a NULL shadow page pointer.
Skip the KVM_REQ_MMU_RELOAD check if there is a valid shadow page for the
root. Zapping shadow pages in response to guest activity, e.g. when the
guest frees a PGD, can trigger KVM_REQ_MMU_RELOAD even if the current
vCPU isn't using the affected root. I.e. KVM_REQ_MMU_RELOAD can be seen
with a completely valid root shadow page. This is a bit of a moot point
as KVM currently unloads all roots on KVM_REQ_MMU_RELOAD, but that will
be cleaned up in the future.
Fixes: a955cad84c ("KVM: x86/mmu: Retry page fault if root is invalidated by memslot update")
Cc: stable@vger.kernel.org
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211209060552.2956723-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Host initiated writes to MSR_IA32_PERF_CAPABILITIES should not depend
on guest visible CPUIDs and (incorrect) KVM logic implementing it is
about to change. Also, KVM_SET_CPUID{,2} after KVM_RUN is now forbidden
and causes test to fail.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: feb627e8d6 ("KVM: x86: Forbid KVM_SET_CPUID{,2} after KVM_RUN")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ability to write to MSR_IA32_PERF_CAPABILITIES from the host should
not depend on guest visible CPUID entries, even if just to allow
creating/restoring guest MSRs and CPUIDs in any sequence.
Fixes: 27461da310 ("KVM: x86/pmu: Support full width counting")
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
