[ Upstream commit 0799e21b5a ]
The parameter 'sk' became useless since the code using it was dropped
from mptcp_get_options() in the commit 8d548ea1dd ("mptcp: do not set
unconditionally csum_reqd on incoming opt"). Let's drop it.
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c1665273bdc7 ("mptcp: strict validation before using mp_opt->hmac")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ]
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b373 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64e47d8afb5ca533b27efc006405e5bcae2c4a7b ]
The value of AM65_CPSW_MAX_PACKET_SIZE represents the maximum length
of a received frame. This value is written to the register
AM65_CPSW_PORT_REG_RX_MAXLEN.
The maximum MTU configured on the network device should then leave
some room for the ethernet headers and frame check. Otherwise, if
the network interface is configured to its maximum mtu possible,
the frames will be larger than AM65_CPSW_MAX_PACKET_SIZE and will
get dropped as oversized.
The switch supports ethernet frame sizes between 64 and 2024 bytes
(including VLAN) as stated in the technical reference manual, so
define AM65_CPSW_MAX_PACKET_SIZE with that maximum size.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240105085530.14070-2-jorge.sanjuangarcia@duagon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80df7d6af7f6d229b34cf237b2cc9024c07111cd ]
The zpci_get_max_write_size() helper is used to determine the maximum
size a PCI store or load can use at a given __iomem address.
For the PCI block store the following restrictions apply:
1. The dst + len must not cross a 4K boundary in the (pseudo-)MMIO space
2. len must not exceed ZPCI_MAX_WRITE_SIZE
3. len must be a multiple of 8 bytes
4. The src address must be double word (8 byte) aligned
5. The dst address must be double word (8 byte) aligned
Otherwise only a normal PCI store which takes its src value from
a register can be used. For these PCI store restriction 1 still applies.
Similarly 1 also applies to PCI loads.
It turns out zpci_max_write_size() instead implements stricter
conditions which prevents PCI block stores from being used where they
can and should be used. In particular instead of conditions 4 and 5 it
wrongly enforces both dst and src to be size aligned. This indirectly
covers condition 1 but also prevents many legal PCI block stores.
On top of the functional shortcomings the zpci_get_max_write_size() is
misnamed as it is used for both read and write size calculations. Rename
it to zpci_get_max_io_size() and implement the listed conditions
explicitly.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Fixes: cd24834130 ("s390/pci: base support")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
[agordeev@linux.ibm.com replaced spaces with tabs]
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12ca110c613a81cb0f0099019c839d078cd0f38 ]
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
Link: https://lore.kernel.org/linux-pci/20230927041845.1222080-1-s-vadapalli@ti.com
Fixes: 49229238ab ("PCI: keystone: Cleanup PHY handling")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a1abc24850eb759e36a2f8869161c3b7254c904 ]
The nvmet_tcp_handle_h2c_data_pdu() function should take into
consideration the possibility that the header digest and/or the data
digests are enabled when calculating the expected PDU length, before
comparing it to the value stored in cmd->pdu_len.
Fixes: efa56305908b ("nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ee7ffeb4ce50c80bc4504db6f39b25a2df6bcf4 ]
An earlier patch had tried to address a warning about a string copy with
missing zero termination:
drivers/nvme/target/trace.h:52:3: warning: ‘strncpy’ specified bound 32 equals destination size [-Wstringop-truncation]
The new version causes a different warning with some compiler versions, notably
gcc-9 and gcc-10, and also misses the zero padding that was apparently done
intentionally in the original code:
drivers/nvme/target/trace.h:56:2: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
Change it to use strscpy_pad() with the original length, which will give
a properly padded and zero-terminated string as well as avoiding the warning.
Fixes: d86481e924 ("nvmet: use min of device_path and disk len")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 017dbfc05c31284150819890b4cc86a699cbdb71 ]
For Gen1 isoc-in transfer, host still send out unexpected ACK after device
finish the burst with a short packet, this will cause an exception on the
connected device, such as, a usb 4k camera.
It can be fixed by setting rxfifo depth less than 4k bytes, prefer to use
3k here, the side-effect is that may cause performance drop about 10%,
including bulk transfer.
Fixes: 926d60ae64 ("usb: xhci-mtk: modify the SOF/ITP interval for mt8195")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55a8210c9e7d21ff2644809699765796d4bfb200 ]
When processing a packed profile in unpack_profile() described like
"profile :ns::samba-dcerpcd /usr/lib*/samba/{,samba/}samba-dcerpcd {...}"
a string ":samba-dcerpcd" is unpacked as a fully-qualified name and then
passed to aa_splitn_fqname().
aa_splitn_fqname() treats ":samba-dcerpcd" as only containing a namespace.
Thus it returns NULL for tmpname, meanwhile tmpns is non-NULL. Later
aa_alloc_profile() crashes as the new profile name is NULL now.
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 6 PID: 1657 Comm: apparmor_parser Not tainted 6.7.0-rc2-dirty #16
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
RIP: 0010:strlen+0x1e/0xa0
Call Trace:
<TASK>
? strlen+0x1e/0xa0
aa_policy_init+0x1bb/0x230
aa_alloc_profile+0xb1/0x480
unpack_profile+0x3bc/0x4960
aa_unpack+0x309/0x15e0
aa_replace_profiles+0x213/0x33c0
policy_update+0x261/0x370
profile_replace+0x20e/0x2a0
vfs_write+0x2af/0xe00
ksys_write+0x126/0x250
do_syscall_64+0x46/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
</TASK>
---[ end trace 0000000000000000 ]---
RIP: 0010:strlen+0x1e/0xa0
It seems such behaviour of aa_splitn_fqname() is expected and checked in
other places where it is called (e.g. aa_remove_profiles). Well, there
is an explicit comment "a ns name without a following profile is allowed"
inside.
AFAICS, nothing can prevent unpacked "name" to be in form like
":samba-dcerpcd" - it is passed from userspace.
Deny the whole profile set replacement in such case and inform user with
EPROTO and an explaining message.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 04dc715e24 ("apparmor: audit policy ns specified in policy load")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0849a5441358cef02586fb2d60f707c0db195628 ]
in nvmet_tcp_handle_h2c_data_pdu(), if the host sends a data_offset
different from rbytes_done, the driver ends up calling nvmet_req_complete()
passing a status error.
The problem is that at this point cmd->req is not yet initialized,
the kernel will crash after dereferencing a NULL pointer.
Fix the bug by replacing the call to nvmet_req_complete() with
nvmet_tcp_fatal_error().
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Reviewed-by: Keith Busch <kbsuch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa56305908ba20de2104f1b8508c6a7401833be ]
If the host sends an H2CData command with an invalid DATAL,
the kernel may crash in nvmet_tcp_build_pdu_iovec().
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp]
Call trace:
process_one_work+0x174/0x3c8
worker_thread+0x2d0/0x3e8
kthread+0x104/0x110
Fix the bug by raising a fatal error if DATAL isn't coherent
with the packet size.
Also, the PDU length should never exceed the MAXH2CDATA parameter which
has been communicated to the host in nvmet_tcp_handle_icreq().
Fixes: 872d26a391 ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66aad7d8d3ec5a3a8ec2023841bcec2ded5f65c9 ]
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 9e98966c7b ("tty: rework break handling")
Link: https://lore.kernel.org/r/20231207132639.18250-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66619686d187b4a6395316b7f39881e945dce4bc ]
If the driver sets TTY_DRIVER_HARDWARE_BREAK, we leave ops->break_ctl()
to the driver and return from send_break(). But we do it using a local
variable and keep the code flowing through the end of the function.
Instead, do 'return' immediately with the ops->break_ctl()'s return
value.
This way, we don't have to stuff the 'else' branch of the 'if' with the
software break handling. And we can re-indent the function too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230919085156.1578-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 66aad7d8d3ec ("usb: cdc-acm: return correct error code on unsupported break")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b73f08bb7fe5a0901646ca5ceaa1e7a2d5ee6293 ]
When reading in_voltage_scale we can get something like:
root@analog:/sys/bus/iio/devices/iio:device2# cat in_voltage_scale
0.038146
However, when reading the available options:
root@analog:/sys/bus/iio/devices/iio:device2# cat
in_voltage_scale_available
2000.000000 2100.000006 2200.000007 2300.000008 2400.000009 2500.000010
which does not make sense. Moreover, when trying to set a new scale we
get an error because there's no call to __ad9467_get_scale() to give us
values as given when reading in_voltage_scale. Fix it by computing the
available scales during probe and properly pass the list when
.read_available() is called.
While at it, change to use .read_available() from iio_info. Also note
that to properly fix this, adi-axi-adc.c has to be changed accordingly.
Fixes: ad67971202 ("iio: adc: ad9467: add support AD9467 ADC")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-4-a4a33bc4d70e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76f028539cf360f750efd8cde560edda298e4c6b ]
The reset gpio was being handled with inverted polarity. This means that
as far as gpiolib is concerned we were actually leaving the pin asserted
(in theory, this would mean reset). However, inverting the polarity in
devicetree made things work. Fix it by doing it the proper way and how
gpiolib expects it to be done.
While at it, moved the handling to it's own function and dropped
'reset_gpio' from the 'struct ad9467_state' as we only need it during
probe. On top of that, refactored things so that we now request the gpio
asserted (i.e in reset) and then de-assert it. Also note that we now use
gpiod_set_value_cansleep() instead of gpiod_direction_output() as we
already request the pin as output.
Fixes: ad67971202 ("iio: adc: ad9467: add support AD9467 ADC")
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-1-a4a33bc4d70e@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 981cf568a8644161c2f15c02278ebc2834b51ba6 ]
When building whole selftests on arm64, rsync gives an erorr about sgx:
rsync: [sender] link_stat "/root/linux-next/tools/testing/selftests/sgx/test_encl.elf" failed: No such file or directory (2)
rsync error: some files/attrs were not transferred (see previous errors) (code 23) at main.c(1327) [sender=3.2.5]
The root casue is sgx only used on X86_64, and shall be skipped on other
platforms.
Fix this by moving TEST_CUSTOM_PROGS and TEST_FILES inside the if check,
then the build result will be "Skipping non-existent dir: sgx".
Fixes: 2adcba79e6 ("selftests/x86: Add a selftest for SGX")
Signed-off-by: Zhao Mengmeng <zhaomengmeng@kylinos.cn>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://lore.kernel.org/all/20231206025605.3965302-1-zhaomzhao%40126.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78d60dae9a0c9f09aa3d6477c94047df2fe6f7b0 ]
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Fixes: cb1a609236 ("serial: imx: implement rts delaying for rs485")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Eberhard Stoll <eberhard.stoll@gmx.de>
Link: https://lore.kernel.org/r/AM0PR09MB26758F651BC1B742EB45775995B8A@AM0PR09MB2675.eurprd09.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad90d0358bd3b4554f243a425168fc7cebe7d04e ]
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
Fixes: e3f0c638f4 ("serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231110152927.70601-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b55d073e6501dc6077edaa945a6dad8ac5c8bbab ]
smatch complains that there is a buffer overflow and clang complains
'ret' is never read.
Smatch error:
drivers/power/supply/bq256xx_charger.c:1578 bq256xx_hw_init() error:
buffer overflow 'bq256xx_watchdog_time' 4 <= 4
Clang static checker:
Value stored to 'ret' is never read.
Add check for buffer overflow and error code from regmap_update_bits().
Fixes: 32e4978bb9 ("power: supply: bq256xx: Introduce the BQ256XX charger driver")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231116041822.1378758-1-suhui@nfschina.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89c4b588d11e9acf01d604de4b0c715884f59213 ]
When calling spi_register_board_info(), we should pass the number of
elements in 'db1200_spi_devs', not 'db1200_i2c_devs'.
Fixes: 63323ec54a ("MIPS: Alchemy: Extended DB1200 board support.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 749b94b08005929bbc636df21a23322733166e35 ]
After unloading a module, we must reset the linear mapping permissions,
see the example below:
Before unloading a module:
0xffffaf809d65d000-0xffffaf809d6dc000 0x000000011d65d000 508K PTE . .. .. D A G . . W R V
0xffffaf809d6dc000-0xffffaf809d6dd000 0x000000011d6dc000 4K PTE . .. .. D A G . . . R V
0xffffaf809d6dd000-0xffffaf809d6e1000 0x000000011d6dd000 16K PTE . .. .. D A G . . W R V
0xffffaf809d6e1000-0xffffaf809d6e7000 0x000000011d6e1000 24K PTE . .. .. D A G . X . R V
After unloading a module:
0xffffaf809d65d000-0xffffaf809d6e1000 0x000000011d65d000 528K PTE . .. .. D A G . . W R V
0xffffaf809d6e1000-0xffffaf809d6e7000 0x000000011d6e1000 24K PTE . .. .. D A G . X W R V
The last mapping is not reset and we end up with WX mappings in the linear
mapping.
So add VM_FLUSH_RESET_PERMS to our module_alloc() definition.
Fixes: 0cff8bff7a ("riscv: avoid the PIC offset of static percpu data in module beyond 2G limits")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20231213134027.155327-2-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f5cc249ff73552d3bd864e62f85841dafaa107d ]
max_low_pfn variable is incorrectly adjusted if the kernel is built with
high memory support and the later is detected in a running system, so the
memory which actually can be directly mapped is getting into the highmem
zone. See the ZONE_NORMAL range on my MIPS32r5 system:
> Zone ranges:
> DMA [mem 0x0000000000000000-0x0000000000ffffff]
> Normal [mem 0x0000000001000000-0x0000000007ffffff]
> HighMem [mem 0x0000000008000000-0x000000020fffffff]
while the zones are supposed to look as follows:
> Zone ranges:
> DMA [mem 0x0000000000000000-0x0000000000ffffff]
> Normal [mem 0x0000000001000000-0x000000001fffffff]
> HighMem [mem 0x0000000020000000-0x000000020fffffff]
Even though the physical memory within the range [0x08000000;0x20000000]
belongs to MMIO on our system, we don't really want it to be considered as
high memory since on MIPS32 that range still can be directly mapped.
Note there might be other problems caused by the max_low_pfn variable
misconfiguration. For instance high_memory variable is initialize with
virtual address corresponding to the max_low_pfn PFN, and by design it
must define the upper bound on direct map memory, then end of the normal
zone. That in its turn potentially may cause problems in accessing the
memory by means of the /dev/mem and /dev/kmem devices.
Let's fix the discovered misconfiguration then. It turns out the commit
a94e4f24ec ("MIPS: init: Drop boot_mem_map") didn't introduce the
max_low_pfn adjustment quite correct. If the kernel is built with high
memory support and the system is equipped with high memory, the
max_low_pfn variable will need to be initialized with PFN of the most
upper directly reachable memory address so the zone normal would be
correctly setup. On MIPS that PFN corresponds to PFN_DOWN(HIGHMEM_START).
If the system is built with no high memory support and one is detected in
the running system, we'll just need to adjust the max_pfn variable to
discard the found high memory from the system and leave the max_low_pfn as
is, since the later will be less than PFN_DOWN(HIGHMEM_START) anyway by
design of the for_each_memblock() loop performed a bit early in the
bootmem_init() method.
Fixes: a94e4f24ec ("MIPS: init: Drop boot_mem_map")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d0a3748a2cb38f9da1f08d357688ebd982eb788 ]
dmi_early_remap() has been defined as ioremap_cache() which on MIPS32 gets
to be converted to the VM-based mapping. DMI early remapping is performed
at the setup_arch() stage with no VM available. So calling the
dmi_early_remap() for MIPS32 causes the system to crash at the early boot
time. Fix that by converting dmi_early_remap() to the uncached remapping
which is always available on both 32 and 64-bits MIPS systems.
Note this change shall not cause any regressions on the current DMI
support implementation because on the early boot-up stage neither MIPS32
nor MIPS64 has the cacheable ioremapping support anyway.
Fixes: be8fa1cb44 ("MIPS: Add support for Desktop Management Interface (DMI)")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6d710b769c1f5f0d55c9ad9bb49b7dce009ec103 upstream.
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502296030ec6b0329e00f9fb15018e170cc63037 upstream.
There appear to be a few different ways that Wacom devices can deal with
confidence:
1. If the device looses confidence in a touch, it will first clear
the tipswitch flag in one report, and then clear the confidence
flag in a second report. This behavior is used by e.g. DTH-2452.
2. If the device looses confidence in a touch, it will clear both
the tipswitch and confidence flags within the same report. This
behavior is used by some AES devices.
3. If the device looses confidence in a touch, it will clear *only*
the confidence bit. The tipswitch bit will remain set so long as
the touch is tracked. This behavior may be used in future devices.
The driver does not currently handle situation 3 properly. Touches that
loose confidence will remain "in prox" and essentially frozen in place
until the tipswitch bit is finally cleared. Not only does this result
in userspace seeing a stuck touch, but it also prevents pen arbitration
from working properly (the pen won't send events until all touches are
up, but we don't currently process events from non-confident touches).
This commit centralizes the checking of the confidence bit in the
wacom_wac_finger_slot() function and has 'prox' depend on it. In the
case where situation 3 is encountered, the treat the touch as though
it was removed, allowing both userspace and the pen arbitration to
act normally.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 7fb0413baa ("HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a25a7df518fc71b1ba981d691e9322e645d2689c upstream.
Previous version of ad7091r event handler received the ADC state pointer
and retrieved the iio device from driver data field with dev_get_drvdata().
However, no driver data have ever been set, which led to null pointer
dereference when running the event handler.
Pass the iio device to the event handler and retrieve the ADC state struct
from it so we avoid the null pointer dereference and save the driver from
filling the driver data field.
Fixes: ca69300173 ("iio: adc: Add support for AD7091R5 ADC")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/5024b764107463de9578d5b3b0a3d5678e307b1a.1702746240.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad362fe07fecf0aba839ff2cc59a3617bd42c33f upstream.
There is a potential UAF scenario in the case of an LPI translation
cache hit racing with an operation that invalidates the cache, such
as a DISCARD ITS command. The root of the problem is that
vgic_its_check_cache() does not elevate the refcount on the vgic_irq
before dropping the lock that serializes refcount changes.
Have vgic_its_check_cache() raise the refcount on the returned vgic_irq
and add the corresponding decrement after queueing the interrupt.
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240104183233.3560639-1-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b95382f965133ef61ce44aaabc518c16eb46909 upstream.
When the VMM writes to ISPENDR0 to set the state pending state of
an SGI, we fail to convey this to the HW if this SGI is already
backed by a GICv4.1 vSGI.
This is a bit of a corner case, as this would only occur if the
vgic state is changed on an already running VM, but this can
apparently happen across a guest reset driven by the VMM.
Fix this by always writing out the pending_latch value to the
HW, and reseting it to false.
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/r/7e7f2c0c-448b-10a9-8929-4b8f4f6e2a32@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
