[ Upstream commit b1b0d5aec1 ]
Currently when the new channel-path is enabled, we do evaluation only
on the subchannels with a device connected on it. This is because,
in the past, if the device in the subchannel is not working or not
available, we used to unregister the subchannels. But, from the 'commit
2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")'
we allow subchannels with or without an active device connected
on it. So, when we do the io_subchannel_verify, make sure that,
we are evaluating the subchannels without any device too.
Fixes: 2297791c92 ("s390/cio: dont unregister subchannel from child-drivers")
Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a089b5d7 ]
Checking the bearer min mtu with tipc_udp_mtu_bad() only works for
IPv4 UDP bearer, and IPv6 UDP bearer has a different value for the
min mtu. This patch checks with encap_hlen + TIPC_MIN_BEARER_MTU
for min mtu, which works for both IPv4 and IPv6 UDP bearer.
Note that tipc_udp_mtu_bad() is still used to check media min mtu
in __tipc_nl_media_set(), as m->mtu currently is only used by the
IPv4 UDP bearer as its default mtu value.
Fixes: 682cd3cf94 ("tipc: confgiure and apply UDP bearer MTU on running links")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56077b56cd ]
When doing link mtu negotiation, a malicious peer may send Activate msg
with a very small mtu, e.g. 4 in Shuang's testing, without checking for
the minimum mtu, l->mtu will be set to 4 in tipc_link_proto_rcv(), then
n->links[bearer_id].mtu is set to 4294967228, which is a overflow of
'4 - INT_H_SIZE - EMSG_OVERHEAD' in tipc_link_mss().
With tipc_link.mtu = 4, tipc_link_xmit() kept printing the warning:
tipc: Too large msg, purging xmit list 1 5 0 40 4!
tipc: Too large msg, purging xmit list 1 15 0 60 4!
And with tipc_link_entry.mtu 4294967228, a huge skb was allocated in
named_distribute(), and when purging it in tipc_link_xmit(), a crash
was even caused:
general protection fault, probably for non-canonical address 0x2100001011000dd: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Not tainted 6.3.0.neta #19
RIP: 0010:kfree_skb_list_reason+0x7e/0x1f0
Call Trace:
<IRQ>
skb_release_data+0xf9/0x1d0
kfree_skb_reason+0x40/0x100
tipc_link_xmit+0x57a/0x740 [tipc]
tipc_node_xmit+0x16c/0x5c0 [tipc]
tipc_named_node_up+0x27f/0x2c0 [tipc]
tipc_node_write_unlock+0x149/0x170 [tipc]
tipc_rcv+0x608/0x740 [tipc]
tipc_udp_recv+0xdc/0x1f0 [tipc]
udp_queue_rcv_one_skb+0x33e/0x620
udp_unicast_rcv_skb.isra.72+0x75/0x90
__udp4_lib_rcv+0x56d/0xc20
ip_protocol_deliver_rcu+0x100/0x2d0
This patch fixes it by checking the new mtu against tipc_bearer_min_mtu(),
and not updating mtu if it is too small.
Fixes: ed193ece26 ("tipc: simplify link mtu negotiation")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ae6d66b60 ]
As different media may requires different min mtu, and even the
same media with different net family requires different min mtu,
add tipc_bearer_min_mtu() to calculate min mtu accordingly.
This API will be used to check the new mtu when doing the link
mtu negotiation in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 56077b56cd ("tipc: do not update mtu if msg_max is too small in mtu negotiation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5306623a98 ]
When initializing XDP in virtnet_open(), some rq xdp initialization
may hit an error causing net device open failed. However, previous
rqs have already initialized XDP and enabled NAPI, which is not the
expected behavior. Need to roll back the previous rq initialization
to avoid leaks in error unwinding of init code.
Also extract helper functions of disable and enable queue pairs.
Use newly introduced disable helper function in error unwinding and
virtnet_close. Use enable helper function in virtnet_open.
Fixes: 754b8a21a9 ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Feng Liu <feliu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: William Tu <witu@nvidia.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27369c9c2b ]
To easily audit the code, better to keep the device stop()
sequence to be mirror of the device open() sequence.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5306623a98 ("virtio_net: Fix error unwinding of XDP initialization")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c83b49383b ]
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff.
Fixes: c411ed8545 ("nsh: add GSO support")
Reported-by: syzbot+632b5d9964208bfef8c0@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ef0785b30 ]
The empty stub functions are defined as global functions, which
causes a warning because of missing prototypes:
drivers/gpu/drm/exynos/exynos_drm_g2d.h:37:5: error: no previous prototype for 'g2d_open'
drivers/gpu/drm/exynos/exynos_drm_g2d.h:42:5: error: no previous prototype for 'g2d_close'
Mark them as 'static inline' to avoid the warning and to make
them behave as intended.
Fixes: eb4d9796fa ("drm/exynos: g2d: Convert to driver component API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a93d2afd3f ]
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed.
Fixes: 55b423d562 ("ASoC: mediatek: mt8186: support audio clock control in platform driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/20230511092437.1.I31cceffc8c45bb1af16eb613e197b3df92cdc19e@changeid
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07a2730593 ]
The trace event recorded incorrect values for the registered family,
protocol, and port because the arguments are in the wrong order.
Fixes: b4af59328c ("SUNRPC: Trace server-side rpcbind registration events")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948f072ada ]
Since the ->xprt_ctxt pointer was added to svc_deferred_req, it has not
been sufficient to use kfree() to free a deferred request. We may need
to free the ctxt as well.
As freeing the ctxt is all that ->xpo_release_rqst() does, we repurpose
it to explicit do that even when the ctxt is not stored in an rqst.
So we now have ->xpo_release_ctxt() which is given an xprt and a ctxt,
which may have been taken either from an rqst or from a dreq. The
caller is now responsible for clearing that pointer after the call to
->xpo_release_ctxt.
We also clear dr->xprt_ctxt when the ctxt is moved into a new rqst when
revisiting a deferred request. This ensures there is only one pointer
to the ctxt, so the risk of double freeing in future is reduced. The
new code in svc_xprt_release which releases both the ctxt and any
rq_deferred depends on this.
Fixes: 773f91b2cf ("SUNRPC: Fix NFSD's request deferral on RDMA transports")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8d3a2c80 ]
When an RPC request is deferred, the rq_xprt_ctxt pointer is moved out
of the svc_rqst into the svc_deferred_req.
When the deferred request is revisited, the pointer is copied into
the new svc_rqst - and also remains in the svc_deferred_req.
In the (rare?) case that the request is deferred a second time, the old
svc_deferred_req is reused - it still has all the correct content.
However in that case the rq_xprt_ctxt pointer is NOT cleared so that
when xpo_release_xprt is called, the ctxt is freed (UDP) or possible
added to a free list (RDMA).
When the deferred request is revisited for a second time, it will
reference this ctxt which may be invalid, and the free the object a
second time which is likely to oops.
So change svc_defer() to *always* clear rq_xprt_ctxt, and assert that
the value is now stored in the svc_deferred_req.
Fixes: 773f91b2cf ("SUNRPC: Fix NFSD's request deferral on RDMA transports")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f5bb36bf9 ]
When Universal DVB card is detaching, netup_unidvb_dma_fini()
uses del_timer() to stop dma->timeout timer. But when timer
handler netup_unidvb_dma_timeout() is running, del_timer()
could not stop it. As a result, the use-after-free bug could
happen. The process is shown below:
(cleanup routine) | (timer routine)
| mod_timer(&dev->tx_sim_timer, ..)
netup_unidvb_finidev() | (wait a time)
netup_unidvb_dma_fini() | netup_unidvb_dma_timeout()
del_timer(&dma->timeout); |
| ndev->pci_dev->dev //USE
Fix by changing del_timer() to del_timer_sync().
Link: https://lore.kernel.org/linux-media/20230308125514.4208-1-duoming@zju.edu.cn
Fixes: 52b1eaf4c5 ("[media] netup_unidvb: NetUP Universal DVB-S/S2/T/T2/C PCI-E card driver")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b45d5ff8c ]
The timeout of the cmdq reset command has been increased to
resolve the reset timeout issue in the full VF scenario.
The timeout of other cmdq commands remains unchanged.
Fixes: 8d307f8e8c ("net: hns3: create new set of unified hclge_comm_cmd_send APIs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 814d0c7860 ]
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 6988eb2a9b ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f14db07064 ]
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 35d93a3004 ("net: hns3: adjust the process of PF reset")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89f6bfb071 ]
In function hns3_dump_tx_queue_info, The print buffer is not enough when
the tx BD number is configured to 32760. As a result several BD
information wouldn't be displayed.
So fix it by increasing the tx queue print buffer length.
Fixes: 630a6738da ("net: hns3: adjust string spaces of some parameters of tx bd info in debugfs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec52b69c04 ]
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebe9bc5095 ]
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e4b45f20c ]
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d80fc101d2 ]
In commit 20704bd163 ("erspan: build the header with the right proto
according to erspan_ver"), it gets the proto with t->parms.erspan_ver,
but t->parms.erspan_ver is not used by collect_md branch, and instead
it should get the proto with md->version for collect_md.
Thanks to Kevin for pointing this out.
Fixes: 20704bd163 ("erspan: build the header with the right proto according to erspan_ver")
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Reported-by: Kevin Traynor <ktraynor@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ab5fc55d7 ]
Smatch reports:
drivers/tty/serial/arc_uart.c:631 arc_serial_probe() warn:
'port->membase' from of_iomap() not released on lines: 631.
In arc_serial_probe(), if uart_add_one_port() fails,
port->membase is not released, which would cause a resource leak.
To fix this, I replace of_iomap with devm_platform_ioremap_resource.
Fixes: 8dbe1d5e09 ("serial/arc: inline the probe helper")
Signed-off-by: Ke Zhang <m202171830@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230428031636.44642-1-m202171830@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e306ec49a ]
When tcp_v4_send_reset() is called with @sk == NULL,
we do not change ctl_sk->sk_priority, which could have been
set from a prior invocation.
Change tcp_v4_send_reset() to set sk_priority and sk_mark
fields before calling ip_send_unicast_reply().
This means tcp_v4_send_reset() and tcp_v4_send_ack()
no longer have to clear ctl_sk->sk_mark after
their call to ip_send_unicast_reply().
Fixes: f6c0f5d209 ("tcp: honor SO_PRIORITY in TIME_WAIT state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d4486efe9 ]
When client and server establish a connection through vsock,
the client send a request to the server to initiate the connection,
then start a timer to wait for the server's response. When the server's
RESPONSE message arrives, the timer also times out and exits. The
server's RESPONSE message is processed first, and the connection is
established. However, the client's timer also times out, the original
processing logic of the client is to directly set the state of this vsock
to CLOSE and return ETIMEDOUT. It will not notify the server when the port
is released, causing the server port remain.
when client's vsock_connect timeout，it should check sk state is
ESTABLISHED or not. if sk state is ESTABLISHED, it means the connection
is established, the client should not set the sk state to CLOSE
Note: I encountered this issue on kernel-4.18, which can be fixed by
this patch. Then I checked the latest code in the community
and found similar issue.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Zhuang Shengen <zhuangshengen@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92553ee031 ]
The Pavilion 15 line has B&O top speakers similar to the x360 and
applying the same profile produces good sound. Without this, the
sound would be tinny and underpowered without either applying
model=alc295-hp-x360 or booting another OS first.
Signed-off-by: Ryan Underwood <nemesis@icequake.net>
Fixes: 563785edfc ("ALSA: hda/realtek - Add quirk entry for HP Pavilion 15")
Link: https://lore.kernel.org/r/ZF0mpcMz3ezP9KQw@icequake.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b01db2740 ]
Introduce the W/A for packet errors seen with short cables (<1m) between
two DP83867 PHYs.
The W/A recommended by DM requires FFE Equalizer Configuration tuning by
writing value 0x0E81 to DSP_FFE_CFG register (0x012C), surrounded by hard
and soft resets as follows:
write_reg(0x001F, 0x8000); //hard reset
write_reg(DSP_FFE_CFG, 0x0E81);
write_reg(0x001F, 0x4000); //soft reset
Since DP83867 PHY DM says "Changing this register to 0x0E81, will not
affect Long Cable performance.", enable the W/A by default.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f816b9829b ]
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f97b8401e0 ]
On some distributions, the rp_filter is automatically set (=1) by
default on a netdev basis (also on VRFs).
In an SRv6 End.DT4 behavior, decapsulated IPv4 packets are routed using
the table associated with the VRF bound to that tunnel. During lookup
operations, the rp_filter can lead to packet loss when activated on the
VRF.
Therefore, we chose to make this selftest more robust by explicitly
disabling the rp_filter during tests (as it is automatically set by some
Linux distributions).
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Tested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21a933c79a ]
The srv6_end_dt4_l3vpn_test instantiates a virtual network consisting of
several routers (rt-1, rt-2) and hosts.
When the IPv6 addresses of rt-{1,2} routers are configured, the Deduplicate
Address Detection (DAD) kicks in when enabled in the Linux distros running
the selftests. DAD is used to check whether an IPv6 address is already
assigned in a network. Such a mechanism consists of sending an ICMPv6 Echo
Request and waiting for a reply.
As the DAD process could take too long to complete, it may cause the
failing of some tests carried out by the srv6_end_dt4_l3vpn_test script.
To make the srv6_end_dt4_l3vpn_test more robust, we disable DAD on routers
since we configure the virtual network manually and do not need any address
deduplication mechanism at all.
Fixes: 2195444e09 ("selftests: add selftest for the SRv6 End.DT4 behavior")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf3128a7ac ]
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d776e31c8 ]
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c5a7680e6 ]
struct platform_driver::remove returning an integer made driver authors
expect that returning an error code was proper error handling. However
the driver core ignores the error and continues to remove the device
because there is nothing the core could do anyhow and reentering the
remove callback again is only calling for trouble.
So this is an source for errors typically yielding resource leaks in the
error path.
As there are too many platform drivers to neatly convert them all to
return void in a single go, do it in several steps after this patch:
a) Convert all drivers to implement .remove_new() returning void instead
of .remove() returning int;
b) Change struct platform_driver::remove() to return void and so make
it identical to .remove_new();
c) Change all drivers back to .remove() now with the better prototype;
d) drop struct platform_driver::remove_new().
While this touches all drivers eventually twice, steps a) and c) can be
done one driver after another and so reduces coordination efforts
immensely and simplifies review.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221209150914.3557650-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 17955aba78 ("ASoC: fsl_micfil: Fix error handler with pm_runtime_enable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fc46f9421 ]
This reverts commit b0355dbbf1.
The reverted commit clears the secpath on packets received via xfrm interfaces
to support nested IPsec tunnels. This breaks Netfilter policy matching using
xt_policy in the FORWARD chain, as the secpath is missing during forwarding.
Additionally, Benedict Wong reports that it breaks Transport-in-Tunnel mode.
Fix this regression by reverting the commit until we have a better approach
for nested IPsec tunnels.
Fixes: b0355dbbf1 ("Fix XFRM-I support for nested ESP tunnels")
Link: https://lore.kernel.org/netdev/20230412085615.124791-1-martin@strongswan.org/
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 430cac4874 ]
The current code doesn't let a simple "allow" policy counteract a
default policy blocking all incoming packets:
ip x p setdefault in block
ip x p a src 192.168.2.1/32 dst 192.168.2.2/32 dir in action allow
At this stage, we have an allow policy (with or without transforms)
for this packet. It doesn't matter what the default policy says, since
the policy we looked up lets the packet through. The case of a
blocking policy is already handled separately, so we can remove this
check.
Fixes: 2d151d3907 ("xfrm: Add possibility to set the default to block if we have no policy")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 720b47229a ]
The gfx.cp_ecc_error_irq is retired in gfx11. In gfx_v11_0_hw_fini still
use amdgpu_irq_put to disable this interrupt, which caused the call trace
in this function.
[ 102.873958] Call Trace:
[ 102.873959] <TASK>
[ 102.873961] gfx_v11_0_hw_fini+0x23/0x1e0 [amdgpu]
[ 102.874019] gfx_v11_0_suspend+0xe/0x20 [amdgpu]
[ 102.874072] amdgpu_device_ip_suspend_phase2+0x240/0x460 [amdgpu]
[ 102.874122] amdgpu_device_ip_suspend+0x3d/0x80 [amdgpu]
[ 102.874172] amdgpu_device_pre_asic_reset+0xd9/0x490 [amdgpu]
[ 102.874223] amdgpu_device_gpu_recover.cold+0x548/0xce6 [amdgpu]
[ 102.874321] amdgpu_debugfs_reset_work+0x4c/0x70 [amdgpu]
[ 102.874375] process_one_work+0x21f/0x3f0
[ 102.874377] worker_thread+0x200/0x3e0
[ 102.874378] ? process_one_work+0x3f0/0x3f0
[ 102.874379] kthread+0xfd/0x130
[ 102.874380] ? kthread_complete_and_exit+0x20/0x20
[ 102.874381] ret_from_fork+0x22/0x30
v2:
- Handle umc and gfx ras cases in separated patch
- Retired the gfx_v11_0_cp_ecc_error_irq_funcs in gfx11
v3:
- Improve the subject and code comments
- Add judgment on gfx11 in the function of amdgpu_gfx_ras_late_init
v4:
- Drop the define of CP_ME1_PIPE_INST_ADDR_INTERVAL and
SET_ECC_ME_PIPE_STATE which using in gfx_v11_0_set_cp_ecc_error_state
- Check cp_ecc_error_irq.funcs rather than ip version for a more
sustainable life
v5:
- Simplify judgment conditions
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
