commit e39cdacf2f upstream.
During the driver loading process, the 'dev' field was not assigned, but
the 'dev' field was referenced in the subsequent 'i82092aa_set_mem_map'
function.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
CC: <stable@vger.kernel.org>
[linux@dominikbrodowski.net: shorten commit message, add Cc to stable]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9a936d6c3d upstream.
Correct big-endian accesses to the CBUS UART, a Malta on-board discrete
TI16C550C part wired directly to the system controller's device bus, and
do not use byte swapping with the 32-bit accesses to the device.
The CBUS is used for devices such as the boot flash memory needed early
on in system bootstrap even before PCI has been initialised. Therefore
it uses the system controller's device bus, which follows the endianness
set with the CPU, which means no byte-swapping is ever required for data
accesses to CBUS, unlike with PCI.
The CBUS UART uses the UPIO_MEM32 access method, that is the `readl' and
`writel' MMIO accessors, which on the MIPS platform imply byte-swapping
with PCI systems. Consequently the wrong byte lane is accessed with the
big-endian configuration and the UART is not correctly accessed.
As it happens the UPIO_MEM32BE access method makes use of the `ioread32'
and `iowrite32' MMIO accessors, which still use `readl' and `writel'
respectively, however they byte-swap data passed, effectively cancelling
swapping done with the accessors themselves and making it suitable for
the CBUS UART.
Make the CBUS UART switch between UPIO_MEM32 and UPIO_MEM32BE then,
based on the endianness selected. With this change in place the device
is correctly recognised with big-endian Malta at boot, along with the
Super I/O devices behind PCI:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Fixes: e7c4782f92 ("[MIPS] Put an end to <asm/serial.h>'s long and annyoing existence")
Cc: stable@vger.kernel.org # v2.6.23+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260524430.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5227c5109 upstream.
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76f22c93b2 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
The driver uses a zero-length i2c-read request for type detection so
update the control-request code to use usb_sndctrlpipe() in this case.
Note that actually trying to read the i2c register in question does not
work as the register might not exist (e.g. depending on the demodulator)
as reported by Eero Lehtinen <debiangamer2@gmail.com>.
Reported-by: syzbot+faf11bbadc5a372564da@syzkaller.appspotmail.com
Reported-by: Eero Lehtinen <debiangamer2@gmail.com>
Tested-by: Eero Lehtinen <debiangamer2@gmail.com>
Fixes: d0f232e823 ("[media] rtl28xxu: add heuristic to detect chip type")
Cc: stable@vger.kernel.org # 4.0
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf88fef0b6 upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c18e9baee upstream.
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30fad76ce4 upstream.
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 1-...!: (2 ticks this GP) idle=d92/1/0x4000000000000000
softirq=25390/25392 fqs=3
(t=12164 jiffies g=31645 q=43226)
rcu: rcu_preempt kthread starved for 12162 jiffies! g31645 f0x0
RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time,
OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:R running task
...........
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: usb_submit_urb failed: -19
The function usbtmc_interrupt() resubmits urbs when the error status
of an urb is -EPROTO. In systems using the dummy_hcd usb controller
this can result in endless interrupt loops when the usbtmc device is
disconnected from the host system.
Since host controller drivers already try to recover from transmission
errors, there is no need to resubmit the urb or try other solutions
to repair the error situation.
In case of errors the INT pipe just stops to wait for further packets.
Fixes: dbf3e7f654 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation")
Cc: stable@vger.kernel.org
Reported-by: syzbot+e2eae5639e7203360018@syzkaller.appspotmail.com
Signed-off-by: Qiang.zhang <qiang.zhang@windriver.com>
Acked-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Link: https://lore.kernel.org/r/20210723004334.458930-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e04480920d ]
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743e ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f8 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e67 ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e67 ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942e560a3d ]
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes: 6cca200362 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44712965bf ]
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af35fc3735 ]
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb653827c7 ]
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc8936 ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28bbbb9875 ]
When cross compiling a MIPS kernel on a BSD based HOSTCC leads
to errors like
SYNC include/config/auto.conf.cmd - due to: .config
egrep: empty (sub)expression
UPD include/config/kernel.release
HOSTCC scripts/dtc/dtc.o - due to target missing
It turns out that egrep uses this egrep pattern:
(|MINOR_|PATCHLEVEL_)
This is not valid syntax or gives undefined results according
to POSIX 9.5.3 ERE Grammar
https://pubs.opengroup.org/onlinepubs/9699919799/basedefs/V1_chap09.html
It seems to be silently accepted by the Linux egrep implementation
while a BSD host complains.
Such patterns can be replaced by a transformation like
"(|p1|p2)" -> "(p1|p2)?"
Fixes: 48c35b2d24 ("[MIPS] There is no __GNUC_MAJOR__")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fe74dfd41 ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c592b46907 ]
If a vb2_queue sets q->min_buffers_needed then when the number of
queued buffers reaches q->min_buffers_needed, vb2_core_qbuf() will call
the start_streaming() callback. If start_streaming() returns an error,
then that error was just returned by vb2_core_qbuf(), but the buffer
was still queued. However, userspace expects that if VIDIOC_QBUF fails,
the buffer is returned dequeued.
So if start_streaming() fails, then remove the buffer from the queue,
thus avoiding this unwanted side-effect.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Fixes: b3379c6201 ("[media] vb2: only call start_streaming if sufficient buffers are queued")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c04243a56 ]
Media event code 3 is defined in the MMC-6 spec as follows:
"MediaRemoval: The media has been removed from the specified slot, and
the Drive is unable to access the media without user intervention. This
applies to media changers only."
This indicated that treating the condition as an EJECT_REQUEST was
appropriate. However, doing so had the unfortunate side-effect of causing
the drive tray to be physically ejected on resume. Instead treat the event
as a MEDIA_CHANGE request.
Fixes: 7dd753ca59 ("scsi: sr: Return appropriate error code when disk is ejected")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213759
Link: https://lore.kernel.org/r/20210726114913.6760-1-limanyi@uniontech.com
Signed-off-by: Li Manyi <limanyi@uniontech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 97367c9722 upstream.
It turned out that the current implementation of the port subscription
is racy. The subscription contains two linked lists, and we have to
add to or delete from both lists. Since both connection and
disconnection procedures perform the same order for those two lists
(i.e. src list, then dest list), when a deletion happens during a
connection procedure, the src list may be deleted before the dest list
addition completes, and this may lead to a use-after-free or an Oops,
even though the access to both lists are protected via mutex.
The simple workaround for this race is to change the access order for
the disconnection, namely, dest list, then src list. This assures
that the connection has been established when disconnecting, and also
the concurrent deletion can be avoided.
Reported-and-tested-by: folkert <folkert@vanheusden.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210801182754.GP890690@belle.intranet.vanheusden.com
Link: https://lore.kernel.org/r/20210803114312.2536-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d5c3954b3 upstream.
Commit 3a70dd2d05 ("spi: mediatek: fix fifo rx mode") claims that
fifo RX mode was never handled, and adds the presumably missing code
to the FIFO transfer function. However, the claim that receive data
was not handled is incorrect. It was handled as part of interrupt
handling after the transfer was complete. The code added with the above
mentioned commit reads data from the receive FIFO before the transfer
is started, which is wrong. This results in an actual transfer error
on a Hayato Chromebook.
Remove the code trying to handle receive data before the transfer is
started to fix the problem.
Fixes: 3a70dd2d05 ("spi: mediatek: fix fifo rx mode")
Cc: Peter Hess <peter.hess@ph-home.de>
Cc: Frank Wunderlich <frank-w@public-files.de>
Cc: Tzung-Bi Shih <tzungbi@google.com>
Cc: Hsin-Yi Wang <hsinyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20210802030023.1748777-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a17ad09617 ]
In some cases skb head could be locked and entire header
data is pulled from skb. When skb_zerocopy() called in such cases,
following BUG is triggered. This patch fixes it by copying entire
skb in such cases.
This could be optimized incase this is performance bottleneck.
---8<---
kernel BUG at net/core/skbuff.c:2961!
invalid opcode: 0000 [#1] SMP PTI
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G OE 5.4.0-77-generic #86-Ubuntu
Hardware name: OpenStack Foundation OpenStack Nova, BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:skb_zerocopy+0x37a/0x3a0
RSP: 0018:ffffbcc70013ca38 EFLAGS: 00010246
Call Trace:
<IRQ>
queue_userspace_packet+0x2af/0x5e0 [openvswitch]
ovs_dp_upcall+0x3d/0x60 [openvswitch]
ovs_dp_process_packet+0x125/0x150 [openvswitch]
ovs_vport_receive+0x77/0xd0 [openvswitch]
netdev_port_receive+0x87/0x130 [openvswitch]
netdev_frame_hook+0x4b/0x60 [openvswitch]
__netif_receive_skb_core+0x2b4/0xc90
__netif_receive_skb_one_core+0x3f/0xa0
__netif_receive_skb+0x18/0x60
process_backlog+0xa9/0x160
net_rx_action+0x142/0x390
__do_softirq+0xe1/0x2d6
irq_exit+0xae/0xb0
do_IRQ+0x5a/0xf0
common_interrupt+0xf/0xf
Code that triggered BUG:
int
skb_zerocopy(struct sk_buff *to, struct sk_buff *from, int len, int hlen)
{
int i, j = 0;
int plen = 0; /* length of skb->head fragment */
int ret;
struct page *page;
unsigned int offset;
BUG_ON(!from->head_frag && !hlen);
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6549c46af8 ]
For linear regulators, the n_voltages should be (max - min) / step + 1.
Buck voltage from 1v to 3V, per step 100mV, and vout mask is 0x1f.
If value is from 20 to 31, the voltage will all be fixed to 3V.
And LDO also, just vout range is different from 1.2v to 3v, step is the
same. If value is from 18 to 31, the voltage will also be fixed to 3v.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20210627080418.1718127-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 240246f6b9 ]
In compression write endio sequence, the range which the compressed_bio
writes is marked as uptodate if the last bio of the compressed (sub)bios
is completed successfully. There could be previous bio which may
have failed which is recorded in cb->errors.
Set the writeback range as uptodate only if cb->errors is zero, as opposed
to checking only the last bio's status.
Backporting notes: in all versions up to 4.4 the last argument is always
replaced by "!cb->errors".
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89fb62fde3 ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76a16be07b ]
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b54874ef1 ]
Fix a bug when flow table is created in priority that already
has other flow tables as shown in the below diagram.
If the new flow table (FT-B) has the lowest level in the priority,
we need to connect the flow tables from the previous priority (p0)
to this new table. In addition when this flow table is destroyed
(FT-B), we need to connect the flow tables from the previous
priority (p0) to the next level flow table (FT-C) in the same
priority of the destroyed table (if exists).
---------
|root_ns|
---------
|
--------------------------------
| | |
---------- ---------- ---------
|p(prio)-x| | p-y | | p-n |
---------- ---------- ---------
| |
---------------- ------------------
|ns(e.g bypass)| |ns(e.g. kernel) |
---------------- ------------------
| | |
------- ------ ----
| p0 | | p1 | |p2|
------- ------ ----
| | \
-------- ------- ------
| FT-A | |FT-B | |FT-C|
-------- ------- ------
Fixes: f90edfd279 ("net/mlx5_core: Connect flow tables")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c9d2102c ]
Syzbot reported skb_over_panic() in llc_pdu_init_as_xid_cmd(). The
problem was in wrong LCC header manipulations.
Syzbot's reproducer tries to send XID packet. llc_ui_sendmsg() is
doing following steps:
1. skb allocation with size = len + header size
len is passed from userpace and header size
is 3 since addr->sllc_xid is set.
2. skb_reserve() for header_len = 3
3. filling all other space with memcpy_from_msg()
Ok, at this moment we have fully loaded skb, only headers needs to be
filled.
Then code comes to llc_sap_action_send_xid_c(). This function pushes 3
bytes for LLC PDU header and initializes it. Then comes
llc_pdu_init_as_xid_cmd(). It initalizes next 3 bytes *AFTER* LLC PDU
header and call skb_push(skb, 3). This looks wrong for 2 reasons:
1. Bytes rigth after LLC header are user data, so this function
was overwriting payload.
2. skb_push(skb, 3) call can cause skb_over_panic() since
all free space was filled in llc_ui_sendmsg(). (This can
happen is user passed 686 len: 686 + 14 (eth header) + 3 (LLC
header) = 703. SKB_DATA_ALIGN(703) = 704)
So, in this patch I added 2 new private constansts: LLC_PDU_TYPE_U_XID
and LLC_PDU_LEN_U_XID. LLC_PDU_LEN_U_XID is used to correctly reserve
header size to handle LLC + XID case. LLC_PDU_TYPE_U_XID is used by
llc_pdu_header_init() function to push 6 bytes instead of 3. And finally
I removed skb_push() call from llc_pdu_init_as_xid_cmd().
This changes should not affect other parts of LLC, since after
all steps we just transmit buffer.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+5e5a981ad7cc54c4b2b4@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e4960b3d6 ]
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'err'.
Eliminate the follow smatch warning:
drivers/net/ethernet/mellanox/mlx4/main.c:3538 mlx4_load_one() warn:
missing error code 'err'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 7ae0e400cd ("net/mlx4_core: Flexible (asymmetric) allocation of EQs and MSI-X vectors for PF/VFs")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d237a7f117 ]
The release_sock() is blocking function, it would change the state
after sleeping. In order to evaluate the stated condition outside
the socket lock context, switch to use wait_woken() instead.
Fixes: 6398e23cdb ("tipc: standardize accept routine")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30a56a2b88 ]
In case the entry is evicted via garbage collection there is
delay between the timeout value and the eviction event.
This adjusts the stop value based on how much time has passed.
Fixes: b87a2f9199 ("netfilter: conntrack: add gc worker to remove timed-out entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9a5c358c8 upstream.
When we exceed the limit of BSS entries, this function will free the
new entry, however, at this time, it is the last door to access the
inputed ies, so these ies will be unreferenced objects and cause memory
leak.
Therefore we should free its ies before deallocating the new entry, beside
of dropping it from hidden_list.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Link: https://lore.kernel.org/r/20210628132334.851095-1-phind.uet@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f7b21a0e41 ]
Fix:
../arch/x86/include/asm/proto.h:14:30: warning: ‘struct task_struct’ declared \
inside parameter list will not be visible outside of this definition or declaration
long do_arch_prctl_64(struct task_struct *task, int option, unsigned long arg2);
^~~~~~~~~~~
.../arch/x86/include/asm/proto.h:40:34: warning: ‘struct task_struct’ declared \
inside parameter list will not be visible outside of this definition or declaration
long do_arch_prctl_common(struct task_struct *task, int option,
^~~~~~~~~~~
if linux/sched.h hasn't be included previously. This fixes a build error
when this header is used outside of the kernel tree.
[ bp: Massage commit message. ]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/b76b4be3-cf66-f6b2-9a6c-3e7ef54f9845@web.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5e7b30d24a upstream.
There is a use after free memory corruption during module exit:
- nfcsim_exit()
- nfcsim_device_free(dev0)
- nfc_digital_unregister_device()
This iterates over command queue and frees all commands,
- dev->up = false
- nfcsim_link_shutdown()
- nfcsim_link_recv_wake()
This wakes the sleeping thread nfcsim_link_recv_skb().
- nfcsim_link_recv_skb()
Wake from wait_event_interruptible_timeout(),
call directly the deb->cb callback even though (dev->up == false),
- digital_send_cmd_complete()
Dereference of "struct digital_cmd" cmd which was freed earlier by
nfc_digital_unregister_device().
This causes memory corruption shortly after (with unrelated stack
trace):
nfc nfc0: NFC: nfcsim_recv_wq: Device is down
llcp: nfc_llcp_recv: err -19
nfc nfc1: NFC: nfcsim_recv_wq: Device is down
BUG: unable to handle page fault for address: ffffffffffffffed
Call Trace:
fsnotify+0x54b/0x5c0
__fsnotify_parent+0x1fe/0x300
? vfs_write+0x27c/0x390
vfs_write+0x27c/0x390
ksys_write+0x63/0xe0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
KASAN report:
BUG: KASAN: use-after-free in digital_send_cmd_complete+0x16/0x50
Write of size 8 at addr ffff88800a05f720 by task kworker/0:2/71
Workqueue: events nfcsim_recv_wq [nfcsim]
Call Trace:
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x21/0x140
? digital_send_cmd_complete+0x16/0x50
? digital_send_cmd_complete+0x16/0x50
kasan_report.cold+0x7f/0x11b
? digital_send_cmd_complete+0x16/0x50
? digital_dep_link_down+0x60/0x60
digital_send_cmd_complete+0x16/0x50
nfcsim_recv_wq+0x38f/0x3d5 [nfcsim]
? nfcsim_in_send_cmd+0x4a/0x4a [nfcsim]
? lock_is_held_type+0x98/0x110
? finish_wait+0x110/0x110
? rcu_read_lock_sched_held+0x9c/0xd0
? rcu_read_lock_bh_held+0xb0/0xb0
? lockdep_hardirqs_on_prepare+0x12e/0x1f0
This flow of calling digital_send_cmd_complete() callback on driver exit
is specific to nfcsim which implements reading and sending work queues.
Since the NFC digital device was unregistered, the callback should not
be called.
Fixes: 204bddcb50 ("NFC: nfcsim: Make use of the Digital layer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 928150fad4 upstream.
In esd_usb2_setup_rx_urbs() MAX_RX_URBS coherent buffers are allocated
and there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see esd_usb2_setup_rx_urbs) and this flag cannot be used
with coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/b31b096926dcb35998ad0271aac4b51770ca7cc8.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9969e3c5f4 upstream.
In ems_usb_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see ems_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/r/59aa9fbc9a8cbf9af2bbd2f61a659c480b415800.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e865f0c31 upstream.
In usb_8dev_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see usb_8dev_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/r/d39b458cd425a1cf7f512f340224e6e9563b07bd.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9449ad33be upstream.
For punch holes in EOF blocks, fallocate used buffer write to zero the
EOF blocks in last cluster. But since ->writepage will ignore EOF
pages, those zeros will not be flushed.
This "looks" ok as commit 6bba4471f0 ("ocfs2: fix data corruption by
fallocate") will zero the EOF blocks when extend the file size, but it
isn't. The problem happened on those EOF pages, before writeback, those
pages had DIRTY flag set and all buffer_head in them also had DIRTY flag
set, when writeback run by write_cache_pages(), DIRTY flag on the page
was cleared, but DIRTY flag on the buffer_head not.
When next write happened to those EOF pages, since buffer_head already
had DIRTY flag set, it would not mark page DIRTY again. That made
writeback ignore them forever. That will cause data corruption. Even
directio write can't work because it will fail when trying to drop pages
caches before direct io, as it found the buffer_head for those pages
still had DIRTY flag set, then it will fall back to buffer io mode.
To make a summary of the issue, as writeback ingores EOF pages, once any
EOF page is generated, any write to it will only go to the page cache,
it will never be flushed to disk even file size extends and that page is
not EOF page any more. The fix is to avoid zero EOF blocks with buffer
write.
The following code snippet from qemu-img could trigger the corruption.
656 open("6b3711ae-3306-4bdd-823c-cf1c0060a095.conv.2", O_RDWR|O_DIRECT|O_CLOEXEC) = 11
...
660 fallocate(11, FALLOC_FL_KEEP_SIZE|FALLOC_FL_PUNCH_HOLE, 2275868672, 327680 <unfinished ...>
660 fallocate(11, 0, 2275868672, 327680) = 0
658 pwrite64(11, "
Link: https://lkml.kernel.org/r/20210722054923.24389-2-junxiao.bi@oracle.com
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76b4f357d0 upstream.
KVM_MAX_VCPU_ID is the maximum vcpu-id of a guest, and not the number
of vcpu-ids. Fix array indexed by vcpu-id to have KVM_MAX_VCPU_ID+1
elements.
Note that this is currently no real problem, as KVM_MAX_VCPU_ID is
an odd number, resulting in always enough padding being available at
the end of those arrays.
Nevertheless this should be fixed in order to avoid rare problems in
case someone is using an even number for KVM_MAX_VCPU_ID.
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-Id: <20210701154105.23215-2-jgross@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
