Changes in 4.19.109
EDAC/amd64: Set grain per DIMM
ALSA: hda/realtek - Fix a regression for mute led on Lenovo Carbon X1
net: dsa: bcm_sf2: Forcibly configure IMP port for 1Gb/sec
RDMA/core: Fix pkey and port assignment in get_new_pps
RDMA/core: Fix use of logical OR in get_new_pps
kprobes: Fix optimize_kprobe()/unoptimize_kprobe() cancellation logic
ALSA: hda: do not override bus codec_mask in link_get()
serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE
selftests: fix too long argument
usb: gadget: composite: Support more than 500mA MaxPower
usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags
usb: gadget: serial: fix Tx stall after buffer overflow
drm/msm/mdp5: rate limit pp done timeout warnings
drm: msm: Fix return type of dsi_mgr_connector_mode_valid for kCFI
scsi: megaraid_sas: silence a warning
drm/msm/dsi: save pll state before dsi host is powered off
drm/msm/dsi/pll: call vco set rate explicitly
selftests: forwarding: use proto icmp for {gretap, ip6gretap}_mac testing
net: dsa: b53: Ensure the default VID is untagged
net: ks8851-ml: Remove 8-bit bus accessors
net: ks8851-ml: Fix 16-bit data access
net: ks8851-ml: Fix 16-bit IO operation
watchdog: da9062: do not ping the hw during stop()
s390/cio: cio_ignore_proc_seq_next should increase position index
s390: make 'install' not depend on vmlinux
x86/boot/compressed: Don't declare __force_order in kaslr_64.c
s390/qdio: fill SL with absolute addresses
nvme: Fix uninitialized-variable warning
ice: Don't tell the OS that link is going down
x86/xen: Distribute switch variables for initialization
net: thunderx: workaround BGX TX Underflow issue
ALSA: hda/realtek - Add Headset Mic supported
ALSA: hda/realtek - Fix silent output on Gigabyte X570 Aorus Master
cifs: don't leak -EAGAIN for stat() during reconnect
usb: storage: Add quirk for Samsung Fit flash
usb: quirks: add NO_LPM quirk for Logitech Screen Share
usb: dwc3: gadget: Update chain bit correctly when using sg list
usb: core: hub: fix unhandled return by employing a void function
usb: core: hub: do error out if usb_autopm_get_interface() fails
usb: core: port: do error out if usb_autopm_get_interface() fails
vgacon: Fix a UAF in vgacon_invert_region
mm, numa: fix bad pmd by atomically check for pmd_trans_huge when marking page tables prot_numa
mm: fix possible PMD dirty bit lost in set_pmd_migration_entry()
fat: fix uninit-memory access for partial initialized inode
arm: dts: dra76x: Fix mmc3 max-frequency
tty:serial:mvebu-uart:fix a wrong return
serial: 8250_exar: add support for ACCES cards
vt: selection, close sel_buffer race
vt: selection, push console lock down
vt: selection, push sel_lock up
media: v4l2-mem2mem.c: fix broken links
x86/pkeys: Manually set X86_FEATURE_OSPKE to preserve existing changes
dmaengine: tegra-apb: Fix use-after-free
dmaengine: tegra-apb: Prevent race conditions of tasklet vs free list
dm cache: fix a crash due to incorrect work item cancelling
dm: report suspended device during destroy
dm writecache: verify watermark during resume
ARM: dts: ls1021a: Restore MDIO compatible to gianfar
spi: bcm63xx-hsspi: Really keep pll clk enabled
ASoC: topology: Fix memleak in soc_tplg_link_elems_load()
ASoC: topology: Fix memleak in soc_tplg_manifest_load()
ASoC: intel: skl: Fix pin debug prints
ASoC: intel: skl: Fix possible buffer overflow in debug outputs
dmaengine: imx-sdma: remove dma_slave_config direction usage and leave sdma_event_enable()
ASoC: pcm: Fix possible buffer overflow in dpcm state sysfs output
ASoC: pcm512x: Fix unbalanced regulator enable call in probe error path
ASoC: dapm: Correct DAPM handling of active widgets during shutdown
drm/sun4i: Fix DE2 VI layer format support
drm/sun4i: de2/de3: Remove unsupported VI layer formats
phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval
ARM: dts: imx6: phycore-som: fix emmc supply
RDMA/iwcm: Fix iwcm work deallocation
RMDA/cm: Fix missing ib_cm_destroy_id() in ib_cm_insert_listen()
IB/hfi1, qib: Ensure RCU is locked when accessing list
ARM: imx: build v7_cpu_resume() unconditionally
ARM: dts: am437x-idk-evm: Fix incorrect OPP node names
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
hwmon: (adt7462) Fix an error return in ADT7462_REG_VOLT()
dmaengine: coh901318: Fix a double lock bug in dma_tc_handle()
powerpc: fix hardware PMU exception bug on PowerVM compatibility mode systems
efi/x86: Align GUIDs to their size in the mixed mode runtime wrapper
efi/x86: Handle by-ref arguments covering multiple pages in mixed mode
dm integrity: fix a deadlock due to offloading to an incorrect workqueue
scsi: pm80xx: Fixed kernel panic during error recovery for SATA drive
Linux 4.19.109
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: Iae5cc72b8c7c96b0a15c76657b9c3bcc4341a7aa
Disable CONFIG_DEBUG_DEVRES to fix ABI differences caused by changes to
devres_alloc_node function when this debug option is enabled.
Bug: 151110905
Test: build
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Change-Id: I27ba172843c80ffd1dfbcc6cc4d706c5b18eb5d3
commit 53770f0ec5 upstream.
If we need to perform synchronous I/O in dm_integrity_map_continue(),
we must make sure that we are not in the map function - in order to
avoid the deadlock due to bio queuing in generic_make_request. To
avoid the deadlock, we offload the request to metadata_wq.
However, metadata_wq also processes metadata updates for write requests.
If there are too many requests that get offloaded to metadata_wq at the
beginning of dm_integrity_map_continue, the workqueue metadata_wq
becomes clogged and the system is incapable of processing any metadata
updates.
This causes a deadlock because all the requests that need to do metadata
updates wait for metadata_wq to proceed and metadata_wq waits inside
wait_and_add_new_range until some existing request releases its range
lock (which doesn't happen because the range lock is released after
metadata update).
In order to fix the deadlock, we create a new workqueue offload_wq and
offload requests to it - so that processing of offload_wq is independent
from processing of metadata_wq.
Fixes: 7eada909bf ("dm: add integrity target")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Heinz Mauelshagen <heinzm@redhat.com>
Tested-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8319e9d5ad upstream.
The mixed mode runtime wrappers are fragile when it comes to how the
memory referred to by its pointer arguments are laid out in memory, due
to the fact that it translates these addresses to physical addresses that
the runtime services can dereference when running in 1:1 mode. Since
vmalloc'ed pages (including the vmap'ed stack) are not contiguous in the
physical address space, this scheme only works if the referenced memory
objects do not cross page boundaries.
Currently, the mixed mode runtime service wrappers require that all by-ref
arguments that live in the vmalloc space have a size that is a power of 2,
and are aligned to that same value. While this is a sensible way to
construct an object that is guaranteed not to cross a page boundary, it is
overly strict when it comes to checking whether a given object violates
this requirement, as we can simply take the physical address of the first
and the last byte, and verify that they point into the same physical page.
When this check fails, we emit a WARN(), but then simply proceed with the
call, which could cause data corruption if the next physical page belongs
to a mapping that is entirely unrelated.
Given that with vmap'ed stacks, this condition is much more likely to
trigger, let's relax the condition a bit, but fail the runtime service
call if it does trigger.
Fixes: f6697df36b ("x86/efi: Prevent mixed mode boot corruption with CONFIG_VMAP_STACK=y")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200221084849.26878-4-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63056e8b5e upstream.
Hans reports that his mixed mode systems running v5.6-rc1 kernels hit
the WARN_ON() in virt_to_phys_or_null_size(), caused by the fact that
efi_guid_t objects on the vmap'ed stack happen to be misaligned with
respect to their sizes. As a quick (i.e., backportable) fix, copy GUID
pointer arguments to the local stack into a buffer that is naturally
aligned to its size, so that it is guaranteed to cover only one
physical page.
Note that on x86, we cannot rely on the stack pointer being aligned
the way the compiler expects, so we need to allocate an 8-byte aligned
buffer of sufficient size, and copy the GUID into that buffer at an
offset that is aligned to 16 bytes.
Fixes: f6697df36b ("x86/efi: Prevent mixed mode boot corruption with CONFIG_VMAP_STACK=y")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: linux-efi@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20200221084849.26878-2-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc37a1632d upstream.
PowerVM systems running compatibility mode on a few Power8 revisions are
still vulnerable to the hardware defect that loses PMU exceptions arriving
prior to a context switch.
The software fix for this issue is enabled through the CPU_FTR_PMAO_BUG
cpu_feature bit, nevertheless this bit also needs to be set for PowerVM
compatibility mode systems.
Fixes: 68f2f0d431 ("powerpc: Add a cpu feature CPU_FTR_PMAO_BUG")
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.ibm.com>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200227134715.9715-1-desnesn@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31623468be upstream.
The commit 337c6c9a69 ("ARM: dts: am437x-idk-evm: Disable
OPP50 for MPU") adjusts couple of OPP nodes defined in the
common am4372.dtsi file, but used outdated node names. This
results in these getting treated as new OPP nodes with missing
properties.
Fix this properly by using the correct node names as updated in
commit b9cb2ba718 ("ARM: dts: Use - instead of @ for DT OPP
entries for TI SoCs").
Reported-by: Roger Quadros <rogerq@ti.com>
Fixes: 337c6c9a69 ("ARM: dts: am437x-idk-evm: Disable OPP50 for MPU")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 512a928aff upstream.
This function is not only needed by the platform suspend code, but is also
reused as the CPU resume function when the ARM cores can be powered down
completely in deep idle, which is the case on i.MX6SX and i.MX6UL(L).
Providing the static inline stub whenever CONFIG_SUSPEND is disabled means
that those platforms will hang on resume from cpuidle if suspend is disabled.
So there are two problems:
- The static inline stub masks the linker error
- The function is not available where needed
Fix both by just building the function unconditionally, when
CONFIG_SOC_IMX6 is enabled. The actual code is three instructions long,
so it's arguably ok to just leave it in for all i.MX6 kernel configurations.
Fixes: 05136f0897 ("ARM: imx: support arm power off in cpuidle for i.mx6sx")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817a68a658 upstream.
The packet handling function, specifically the iteration of the qp list
for mad packet processing misses locking RCU before running through the
list. Not only is this incorrect, but the list_for_each_entry_rcu() call
can not be called with a conditional check for lock dependency. Remedy
this by invoking the rcu lock and unlock around the critical section.
This brings MAD packet processing in line with what is done for non-MAD
packets.
Fixes: 7724105686 ("IB/hfi1: add driver files")
Link: https://lore.kernel.org/r/20200225195445.140896.41873.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb0bbba763 upstream.
Currently the vmmc is supplied by the 1.8V pmic rail but this is wrong.
The default module behaviour is to power VCCQ and VCC by the 3.3V power
rail. Optional the user can connect the VCCQ to the pmic 1.8V emmc
power rail using a solder jumper.
Fixes: ddec5d1c00 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46b7edf1c7 upstream.
I've noticed that when writing data to the modem the writes can time out
at some point eventually. Looks like kicking the modem idle GPIO every
600 ms instead of once a second fixes the issue. Note that this rate is
different from our runtime PM autosuspend rate MDM6600_MODEM_IDLE_DELAY_MS
that we still want to keep at 1 second, so let's add a separate define for
PHY_MDM6600_IDLE_KICK_MS.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be4e3c737e upstream.
We have an interrupt handler for the wake-up GPIO pin, but we're missing
the code to wake-up the system. This can cause timeouts receiving data
for the UART that shares the wake-up GPIO pin with the USB PHY.
All we need to do is just wake the system and kick the autosuspend
timeout to fix the issue.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b3193089e upstream.
commit c2caa4da46 ("ASoC: Fix widget powerdown on shutdown") added a
set of the power state during snd_soc_dapm_shutdown to ensure the
widgets powered off. However, when commit 39eb5fd13d
("ASoC: dapm: Delay w->power update until the changes are written")
added the new_power member of the widget structure, to differentiate
between the current power state and the target power state, it did not
update the shutdown to use the new_power member.
As new_power has not updated it will be left in the state set by the
last DAPM sequence, ie. 1 for active widgets. So as the DAPM sequence
for the shutdown proceeds it will turn the widgets on (despite them
already being on) rather than turning them off.
Fixes: 39eb5fd13d ("ASoC: dapm: Delay w->power update until the changes are written")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200228153145.21013-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c89ffea60 upstream.
dpcm_show_state() invokes multiple snprintf() calls to concatenate
formatted strings on the fixed size buffer. The usage of snprintf()
is supposed for avoiding the buffer overflow, but it doesn't work as
expected because snprintf() doesn't return the actual output size but
the size to be written.
Fix this bug by replacing all snprintf() calls with scnprintf()
calls.
Fixes: f86dcef87b ("ASoC: dpcm: Add debugFS support for DPCM")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200218111737.14193-4-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 107d06441b ]
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
ENBLn bit should be set before any dma request triggered, please
refer to the below information from i.mx6sololite RM. Otherwise,
spi/uart test will be fail because there is dma request from tx
fifo always before dmaengine_prep_slave_sg() in where ENBLn set
and violate the below rule.
https://www.nxp.com/docs/en/reference-manual/IMX6SLRM.pdf:
40.8.28 Channel Enable RAM (SDMAARM_CHNENBLn)
"It is thus essential for the Arm platform to program them before
any DMA request is triggered to the SDMA, otherwise an unpredictable
combination of channels may be started".
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
[vkoul: sqashed patch from Robin into direction change]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 549cd0ba04 upstream.
The debugfs output of intel skl driver writes strings with multiple
snprintf() calls with the fixed size. This was supposed to avoid the
buffer overflow but actually it still would, because snprintf()
returns the expected size to be output, not the actual output size.
Fix it by replacing snprintf() calls with scnprintf().
Fixes: d14700a01f ("ASoC: Intel: Skylake: Debugfs facility to dump module config")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200218111737.14193-3-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242c46c023 upstream.
In case of ABI version mismatch, _manifest needs to be freed as
it is just a copy of the original topology manifest. However, if
a driver manifest handler is defined, that would get executed and
the cleanup is never reached. Fix that by getting the return status
of manifest() instead of returning directly.
Fixes: 583958fa2e ("ASoC: topology: Make manifest backward compatible from ABI v4")
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Link: https://lore.kernel.org/r/20200207185325.22320-3-dragos_tarcatu@mentor.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51bddd4501 upstream.
The purpose of commit 0fd85869c2 ("spi/bcm63xx-hsspi: keep pll clk enabled")
was to keep the pll clk enabled through the lifetime of the device.
In order to do that, some 'clk_prepare_enable()'/'clk_disable_unprepare()'
calls have been added in the error handling path of the probe function, in
the remove function and in the suspend and resume functions.
However, a 'clk_disable_unprepare()' call has been unfortunately left in
the probe function. So the commit seems to be more or less a no-op.
Axe it now, so that the pll clk is left enabled through the lifetime of
the device, as described in the commit.
Fixes: 0fd85869c2 ("spi/bcm63xx-hsspi: keep pll clk enabled")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20200228213838.7124-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7155c44624 upstream.
The difference between "fsl,etsec2-mdio" and "gianfar" has to do with
the .get_tbipa function, which calculates the address of the TBIPA
register automatically, if not explicitly specified. [ see
drivers/net/ethernet/freescale/fsl_pq_mdio.c ]. On LS1021A, the TBIPA
register is at offset 0x30 within the port register block, which is what
the "gianfar" method of calculating addresses actually does.
Luckily, the bad "compatible" is inconsequential for ls1021a.dtsi,
because the TBIPA register is explicitly specified via the second "reg"
(<0x0 0x2d10030 0x0 0x4>), so the "get_tbipa" function is dead code.
Nonetheless it's good to restore it to its correct value.
Background discussion:
https://www.spinics.net/lists/stable/msg361156.html
Fixes: c7861adbe3 ("ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adc0daad36 upstream.
The function dm_suspended returns true if the target is suspended.
However, when the target is being suspended during unload, it returns
false.
An example where this is a problem: the test "!dm_suspended(wc->ti)" in
writecache_writeback is not sufficient, because dm_suspended returns
zero while writecache_suspend is in progress. As is, without an
enhanced dm_suspended, simply switching from flush_workqueue to
drain_workqueue still emits warnings:
workqueue writecache-writeback: drain_workqueue() isn't complete after 10 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 100 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 200 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 300 tries
workqueue writecache-writeback: drain_workqueue() isn't complete after 400 tries
writecache_suspend calls flush_workqueue(wc->writeback_wq) - this function
flushes the current work. However, the workqueue may re-queue itself and
flush_workqueue doesn't wait for re-queued works to finish. Because of
this - the function writecache_writeback continues execution after the
device was suspended and then concurrently with writecache_dtr, causing
a crash in writecache_writeback.
We must use drain_workqueue - that waits until the work and all re-queued
works finish.
As a prereq for switching to drain_workqueue, this commit fixes
dm_suspended to return true after the presuspend hook and before the
postsuspend hook - just like during a normal suspend. It allows
simplifying the dm-integrity and dm-writecache targets so that they
don't have to maintain suspended flags on their own.
With this change use of drain_workqueue() can be used effectively. This
change was tested with the lvm2 testsuite and cryptsetup testsuite and
the are no regressions.
Fixes: 48debafe4f ("dm: add writecache target")
Cc: stable@vger.kernel.org # 4.18+
Reported-by: Corey Marthaler <cmarthal@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cdf6a0aae upstream.
The crash can be reproduced by running the lvm2 testsuite test
lvconvert-thin-external-cache.sh for several minutes, e.g.:
while :; do make check T=shell/lvconvert-thin-external-cache.sh; done
The crash happens in this call chain:
do_waker -> policy_tick -> smq_tick -> end_hotspot_period -> clear_bitset
-> memset -> __memset -- which accesses an invalid pointer in the vmalloc
area.
The work entry on the workqueue is executed even after the bitmap was
freed. The problem is that cancel_delayed_work doesn't wait for the
running work item to finish, so the work item can continue running and
re-submitting itself even after cache_postsuspend. In order to make sure
that the work item won't be running, we must use cancel_delayed_work_sync.
Also, change flush_workqueue to drain_workqueue, so that if some work item
submits itself or another work item, we are properly waiting for both of
them.
Fixes: c6b4fcbad0 ("dm: add cache target")
Cc: stable@vger.kernel.org # v3.9
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94788af4ed upstream.
I was doing some experiments with I2C and noticed that Tegra APB DMA
driver crashes sometime after I2C DMA transfer termination. The crash
happens because tegra_dma_terminate_all() bails out immediately if pending
list is empty, and thus, it doesn't release the half-completed descriptors
which are getting re-used before ISR tasklet kicks-in.
tegra-i2c 7000c400.i2c: DMA transfer timeout
elants_i2c 0-0010: elants_i2c_irq: failed to read data: -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 142 at lib/list_debug.c:45 __list_del_entry_valid+0x45/0xac
list_del corruption, ddbaac44->next is LIST_POISON1 (00000100)
Modules linked in:
CPU: 0 PID: 142 Comm: kworker/0:2 Not tainted 5.5.0-rc2-next-20191220-00175-gc3605715758d-dirty #538
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: events_freezable_power_ thermal_zone_device_check
[<c010e5c5>] (unwind_backtrace) from [<c010a1c5>] (show_stack+0x11/0x14)
[<c010a1c5>] (show_stack) from [<c0973925>] (dump_stack+0x85/0x94)
[<c0973925>] (dump_stack) from [<c011f529>] (__warn+0xc1/0xc4)
[<c011f529>] (__warn) from [<c011f7e9>] (warn_slowpath_fmt+0x61/0x78)
[<c011f7e9>] (warn_slowpath_fmt) from [<c042497d>] (__list_del_entry_valid+0x45/0xac)
[<c042497d>] (__list_del_entry_valid) from [<c047a87f>] (tegra_dma_tasklet+0x5b/0x154)
[<c047a87f>] (tegra_dma_tasklet) from [<c0124799>] (tasklet_action_common.constprop.0+0x41/0x7c)
[<c0124799>] (tasklet_action_common.constprop.0) from [<c01022ab>] (__do_softirq+0xd3/0x2a8)
[<c01022ab>] (__do_softirq) from [<c0124683>] (irq_exit+0x7b/0x98)
[<c0124683>] (irq_exit) from [<c0168c19>] (__handle_domain_irq+0x45/0x80)
[<c0168c19>] (__handle_domain_irq) from [<c043e429>] (gic_handle_irq+0x45/0x7c)
[<c043e429>] (gic_handle_irq) from [<c0101aa5>] (__irq_svc+0x65/0x94)
Exception stack(0xde2ebb90 to 0xde2ebbd8)
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200209163356.6439-2-digetx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 735a6dd022 upstream.
Explicitly set X86_FEATURE_OSPKE via set_cpu_cap() instead of calling
get_cpu_cap() to pull the feature bit from CPUID after enabling CR4.PKE.
Invoking get_cpu_cap() effectively wipes out any {set,clear}_cpu_cap()
changes that were made between this_cpu->c_init() and setup_pku(), as
all non-synthetic feature words are reinitialized from the CPU's CPUID
values.
Blasting away capability updates manifests most visibility when running
on a VMX capable CPU, but with VMX disabled by BIOS. To indicate that
VMX is disabled, init_ia32_feat_ctl() clears X86_FEATURE_VMX, using
clear_cpu_cap() instead of setup_clear_cpu_cap() so that KVM can report
which CPU is misconfigured (KVM needs to probe every CPU anyways).
Restoring X86_FEATURE_VMX from CPUID causes KVM to think VMX is enabled,
ultimately leading to an unexpected #GP when KVM attempts to do VMXON.
Arguably, init_ia32_feat_ctl() should use setup_clear_cpu_cap() and let
KVM figure out a different way to report the misconfigured CPU, but VMX
is not the only feature bit that is affected, i.e. there is precedent
that tweaking feature bits via {set,clear}_cpu_cap() after ->c_init()
is expected to work. Most notably, x86_init_rdrand()'s clearing of
X86_FEATURE_RDRAND when RDRAND malfunctions is also overwritten.
Fixes: 0697694564 ("x86/mm/pkeys: Actually enable Memory Protection Keys in the CPU")
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200226231615.13664-1-sean.j.christopherson@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 316e730f1d upstream.
The topology that v4l2_m2m_register_media_controller() creates for a
processing block actually created a source-to-source link and a sink-to-sink
link instead of two source-to-sink links.
Unfortunately v4l2-compliance never checked for such bad links, so this
went unreported for quite some time.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Nicolas Dufresne <nicolas@ndufresne.ca>
Cc: <stable@vger.kernel.org> # for v4.19 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07e6124a1a upstream.
syzkaller reported this UAF:
BUG: KASAN: use-after-free in n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741
Read of size 1 at addr ffff8880089e40e9 by task syz-executor.1/13184
CPU: 0 PID: 13184 Comm: syz-executor.1 Not tainted 5.4.7 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
...
kasan_report+0xe/0x20 mm/kasan/common.c:634
n_tty_receive_buf_common+0x2481/0x2940 drivers/tty/n_tty.c:1741
tty_ldisc_receive_buf+0xac/0x190 drivers/tty/tty_buffer.c:461
paste_selection+0x297/0x400 drivers/tty/vt/selection.c:372
tioclinux+0x20d/0x4e0 drivers/tty/vt/vt.c:3044
vt_ioctl+0x1bcf/0x28d0 drivers/tty/vt/vt_ioctl.c:364
tty_ioctl+0x525/0x15a0 drivers/tty/tty_io.c:2657
vfs_ioctl fs/ioctl.c:47 [inline]
It is due to a race between parallel paste_selection (TIOCL_PASTESEL)
and set_selection_user (TIOCL_SETSEL) invocations. One uses sel_buffer,
while the other frees it and reallocates a new one for another
selection. Add a mutex to close this race.
The mutex takes care properly of sel_buffer and sel_buffer_lth only. The
other selection global variables (like sel_start, sel_end, and sel_cons)
are protected only in set_selection_user. The other functions need quite
some more work to close the races of the variables there. This is going
to happen later.
This likely fixes (I am unsure as there is no reproducer provided) bug
206361 too. It was marked as CVE-2020-8648.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+59997e8d5cbdc486e6f6@syzkaller.appspotmail.com
References: https://bugzilla.kernel.org/show_bug.cgi?id=206361
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210081131.23572-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa63c00397 upstream.
dra76x is not affected by i887 which requires mmc3 node to be limited to
a max frequency of 64 MHz. Fix this by overwriting the correct value in
the the dra76 specific dtsi.
Fixes: 895bd4b3e5 ("ARM: dts: Add support for dra76-evm")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a8683ad9b upstream.
In set_pmd_migration_entry(), pmdp_invalidate() is used to change PMD
atomically. But the PMD is read before that with an ordinary memory
reading. If the THP (transparent huge page) is written between the PMD
reading and pmdp_invalidate(), the PMD dirty bit may be lost, and cause
data corruption. The race window is quite small, but still possible in
theory, so need to be fixed.
The race is fixed via using the return value of pmdp_invalidate() to get
the original content of PMD, which is a read/modify/write atomic
operation. So no THP writing can occur in between.
The race has been introduced when the THP migration support is added in
the commit 616b837153 ("mm: thp: enable thp migration in generic path").
But this fix depends on the commit d52605d7cb ("mm: do not lose dirty
and accessed bits in pmdp_invalidate()"). So it's easy to be backported
after v4.16. But the race window is really small, so it may be fine not
to backport the fix at all.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Link: http://lkml.kernel.org/r/20200220075220.2327056-1-ying.huang@intel.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b272b3cbb upstream.
: A user reported a bug against a distribution kernel while running a
: proprietary workload described as "memory intensive that is not swapping"
: that is expected to apply to mainline kernels. The workload is
: read/write/modifying ranges of memory and checking the contents. They
: reported that within a few hours that a bad PMD would be reported followed
: by a memory corruption where expected data was all zeros. A partial
: report of the bad PMD looked like
:
: [ 5195.338482] ../mm/pgtable-generic.c:33: bad pmd ffff8888157ba008(000002e0396009e2)
: [ 5195.341184] ------------[ cut here ]------------
: [ 5195.356880] kernel BUG at ../mm/pgtable-generic.c:35!
: ....
: [ 5195.410033] Call Trace:
: [ 5195.410471] [<ffffffff811bc75d>] change_protection_range+0x7dd/0x930
: [ 5195.410716] [<ffffffff811d4be8>] change_prot_numa+0x18/0x30
: [ 5195.410918] [<ffffffff810adefe>] task_numa_work+0x1fe/0x310
: [ 5195.411200] [<ffffffff81098322>] task_work_run+0x72/0x90
: [ 5195.411246] [<ffffffff81077139>] exit_to_usermode_loop+0x91/0xc2
: [ 5195.411494] [<ffffffff81003a51>] prepare_exit_to_usermode+0x31/0x40
: [ 5195.411739] [<ffffffff815e56af>] retint_user+0x8/0x10
:
: Decoding revealed that the PMD was a valid prot_numa PMD and the bad PMD
: was a false detection. The bug does not trigger if automatic NUMA
: balancing or transparent huge pages is disabled.
:
: The bug is due a race in change_pmd_range between a pmd_trans_huge and
: pmd_nond_or_clear_bad check without any locks held. During the
: pmd_trans_huge check, a parallel protection update under lock can have
: cleared the PMD and filled it with a prot_numa entry between the transhuge
: check and the pmd_none_or_clear_bad check.
:
: While this could be fixed with heavy locking, it's only necessary to make
: a copy of the PMD on the stack during change_pmd_range and avoid races. A
: new helper is created for this as the check if quite subtle and the
: existing similar helpful is not suitable. This passed 154 hours of
: testing (usually triggers between 20 minutes and 24 hours) without
: detecting bad PMDs or corruption. A basic test of an autonuma-intensive
: workload showed no significant change in behaviour.
Although Mel withdrew the patch on the face of LKML comment
https://lkml.org/lkml/2017/4/10/922 the race window aforementioned is
still open, and we have reports of Linpack test reporting bad residuals
after the bad PMD warning is observed. In addition to that, bad
rss-counter and non-zero pgtables assertions are triggered on mm teardown
for the task hitting the bad PMD.
host kernel: mm/pgtable-generic.c:40: bad pmd 00000000b3152f68(8000000d2d2008e7)
....
host kernel: BUG: Bad rss-counter state mm:00000000b583043d idx:1 val:512
host kernel: BUG: non-zero pgtables_bytes on freeing mm: 4096
The issue is observed on a v4.18-based distribution kernel, but the race
window is expected to be applicable to mainline kernels, as well.
[akpm@linux-foundation.org: fix comment typo, per Rafael]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Link: http://lkml.kernel.org/r/20200216191800.22423-1-aquini@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 513dc792d6 upstream.
When syzkaller tests, there is a UAF:
BUG: KASan: use after free in vgacon_invert_region+0x9d/0x110 at addr
ffff880000100000
Read of size 2 by task syz-executor.1/16489
page:ffffea0000004000 count:0 mapcount:-127 mapping: (null)
index:0x0
page flags: 0xfffff00000000()
page dumped because: kasan: bad access detected
CPU: 1 PID: 16489 Comm: syz-executor.1 Not tainted
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
[<ffffffffb119f309>] dump_stack+0x1e/0x20
[<ffffffffb04af957>] kasan_report+0x577/0x950
[<ffffffffb04ae652>] __asan_load2+0x62/0x80
[<ffffffffb090f26d>] vgacon_invert_region+0x9d/0x110
[<ffffffffb0a39d95>] invert_screen+0xe5/0x470
[<ffffffffb0a21dcb>] set_selection+0x44b/0x12f0
[<ffffffffb0a3bfae>] tioclinux+0xee/0x490
[<ffffffffb0a1d114>] vt_ioctl+0xff4/0x2670
[<ffffffffb0a0089a>] tty_ioctl+0x46a/0x1a10
[<ffffffffb052db3d>] do_vfs_ioctl+0x5bd/0xc40
[<ffffffffb052e2f2>] SyS_ioctl+0x132/0x170
[<ffffffffb11c9b1b>] system_call_fastpath+0x22/0x27
Memory state around the buggy address:
ffff8800000fff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
ffff8800000fff80: 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
>ffff880000100000: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff
It can be reproduce in the linux mainline by the program:
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <linux/vt.h>
struct tiocl_selection {
unsigned short xs; /* X start */
unsigned short ys; /* Y start */
unsigned short xe; /* X end */
unsigned short ye; /* Y end */
unsigned short sel_mode; /* selection mode */
};
#define TIOCL_SETSEL 2
struct tiocl {
unsigned char type;
unsigned char pad;
struct tiocl_selection sel;
};
int main()
{
int fd = 0;
const char *dev = "/dev/char/4:1";
struct vt_consize v = {0};
struct tiocl tioc = {0};
fd = open(dev, O_RDWR, 0);
v.v_rows = 3346;
ioctl(fd, VT_RESIZEX, &v);
tioc.type = TIOCL_SETSEL;
ioctl(fd, TIOCLINUX, &tioc);
return 0;
}
When resize the screen, update the 'vc->vc_size_row' to the new_row_size,
but when 'set_origin' in 'vgacon_set_origin', vgacon use 'vga_vram_base'
for 'vc_origin' and 'vc_visible_origin', not 'vc_screenbuf'. It maybe
smaller than 'vc_screenbuf'. When TIOCLINUX, use the new_row_size to calc
the offset, it maybe larger than the vga_vram_size in vgacon driver, then
bad access.
Also, if set an larger screenbuf firstly, then set an more larger
screenbuf, when copy old_origin to new_origin, a bad access may happen.
So, If the screen size larger than vga_vram, resize screen should be
failed. This alse fix CVE-2020-8649 and CVE-2020-8647.
Linus pointed out that overflow checking seems absent. We're saved by
the existing bounds checks in vc_do_resize() with rather strict
limits:
if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW)
return -EINVAL;
Fixes: 0aec4867dc ("[PATCH] SVGATextMode fix")
Reference: CVE-2020-8647 and CVE-2020-8649
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
[danvet: augment commit message to point out overflow safety]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200304022429.37738-1-zhangxiaoxu5@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
