For verifying reciving the EI interrupts, we need to hold the GPU in
very precise conditions (in terms of C0 cycles during the EI). If we
preempt the busy load to handle the heartbeat, this may perturb the busy
load causing us to miss the interrupt.
The other tests, while not as time sensitive, may also be slightly
perturbed, so apply the heartbeat protection across all the
measurements.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422083855.26842-1-chris@chris-wilson.co.uk
AUX power wells sometimes need additional handling besides just
programming the specific power well registers:
* Type-C PHY's also require additional Type-C register programming
* ICL combo PHY's require additional workarounds
* TGL & EHL combo PHY's can be treated like any other power well
Today we have dedicated aux ops for the ICL combo PHY and Type-C cases.
This works fine, but means that when a new platform shows up with
identical general power well handling, but different types of PHYs on
its outputs, we have to define an entire new power well table for that
platform and can't just re-use the table from the earlier platform -- as
an example, see ehl_power_wells[], which is a subset of
icl_power_wells[], *except* that we need to specify different AUX ops
for the third display.
If we instead create a single set of top-level aux ops that will check
the PHY type and then dispatch to the appropriate handlers, we can get
more reuse out of our power well definitions. This allows us to
immediately eliminate ehl_power_wells[] and simply reuse the ICL table;
if future platforms follow the same general power well assignments as
either ICL or TGL, we'll be able to re-use those tables in the same way.
Note that I've only changed ICL+ platforms over to using the new icl_aux
ops; at this point it's unlikely that we'll have any new platforms that
re-use gen9 or earlier power well configurations.
v2:
- ICL_AUX_PW_TO_PHY() won't return the proper PHY for TBT AUX power
wells. But we know those wells will only used on Type-C outputs
anyway, so we can just check is is_tc_tbt flag in the condition.
(Jose).
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415233435.3064257-2-matthew.d.roper@intel.com
igt_ppgtt_pin_update() invokes i915_gem_context_get_vm_rcu(), which
returns a reference of the i915_address_space object to "vm" with
increased refcount.
When igt_ppgtt_pin_update() returns, "vm" becomes invalid, so the
refcount should be decreased to keep refcount balanced.
The reference counting issue happens in two exception handling paths of
igt_ppgtt_pin_update(). When i915_gem_object_create_internal() returns
IS_ERR, the refcnt increased by i915_gem_context_get_vm_rcu() is not
decreased, causing a refcnt leak.
Fix this issue by jumping to "out_vm" label when
i915_gem_object_create_internal() returns IS_ERR.
Fixes: a4e7ccdac3 ("drm/i915: Move context management under GEM")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1587361342-83494-1-git-send-email-xiyuyang19@fudan.edu.cn
We shouldn't try to do link retraining from the short hpd handler.
We can't take any modeset locks there so this is racy as hell.
Push the whole thing into the hotplug work like we do with SST.
We'll just have to adjust the SST retraining code to deal with
the MST encoders and multiple pipes.
TODO: I have a feeling we should just rip this all out and
do a full modeset instead. Stuff like port sync and the tgl+
MST master transcoder stuff maybe doesn't work well if we
try to retrain without following the proper modeset sequence.
So far haven't done any actual tests to confirm that though.
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417152734.464-2-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
Fix the warning caused by enabling the autosectionlabel extension in the
kernel Sphinx build:
Documentation/gpu/i915.rst:610: WARNING: duplicate label
gpu/i915:layout, other instance in Documentation/gpu/i915.rst
The autosectionlabel extension adds labels to each section title for
cross-referencing, but forbids identical section titles in a
document. With kernel-doc, this includes sections titles in the included
kernel-doc comments.
In the warning message, Sphinx is unable to reference the labels in
their true locations in the kernel-doc comments in source. In this case,
there's "Layout" sections in both gt/intel_workarounds.c and
i915_reg.h. Rename the section in the latter to "File Layout".
Fixes: 58ad30cf91 ("docs: fix reference to core-api/namespaces.rst")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417130109.12791-1-jani.nikula@intel.com
Right now dp.regs.dp_tp_ctl/status are only set during the encoder
pre_enable() hook, what is causing all reads and writes to those
registers to go to offset 0x0 before pre_enable() is executed.
So if i915 takes the BIOS state and don't do a modeset any following
link retraing will fail.
In the case that i915 needs to do a modeset, the DDI disable sequence
will write to a wrong register not disabling DP 'Transport Enable' in
DP_TP_CTL, making a HDMI modeset in the same port/transcoder to
not light up the monitor.
So here for GENs older than 12, that have those registers fixed at
port offset range it is loading at encoder/port init while for GEN12
it will keep setting it at encoder pre_enable() and during HW state
readout.
Fixes: 4444df6e20 ("drm/i915/tgl: move DP_TP_* to transcoder")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414230442.262092-1-jose.souza@intel.com
TC ports can enter in TCCOLD to save power and is required to request
to PCODE to exit this state before use or read to TC registers.
For TGL there is a new MBOX command to do that with a parameter to ask
PCODE to exit and block TCCOLD entry or unblock TCCOLD entry.
So adding a new power domain to reuse the refcount and only allow
TC cold when all TC ports are not in use.
v2:
- fixed missing case in intel_display_power_domain_str()
- moved tgl_tc_cold_request to intel_display_power.c
- renamed TGL_TC_COLD_OFF to TGL_TC_COLD_OFF_POWER_DOMAINS
- added all TC and TBT aux power domains to
TGL_TC_COLD_OFF_POWER_DOMAINS
v3:
- added one msec sleep when PCODE returns -EAGAIN
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
v4:
- Made failure to block or unblock TC cold a error
- removed 5msec timeout, instead giving PCODE 1msec by up 3 times to
recover from the internal error
v5:
- only sleeping 1msec when ret is -EAGAIN
BSpec: 49294
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-6-jose.souza@intel.com
This is required for legacy/static TC ports as IOM is not aware of
the connection and will not trigger the TC cold exit.
Just request PCODE to exit TCCOLD is not enough as it could enter
again before driver makes use of the port, to prevent it BSpec states
that aux powerwell should be held.
So here embedding the TC cold exit sequence into ICL aux enable,
it will enable aux and then request TC cold to exit.
The TC cold block(exit and aux hold) and unblock was added to some
exported TC functions for the others and to access PHY registers,
callers should enable and keep aux powerwell enabled during access.
Also adding TC cold check and warnig in tc_port_load_fia_params() as
at this point of the driver initialization we can't request power
wells, if we get this warning we will need to figure out how to handle
it.
v2:
- moved ICL TC cold exit function to intel_display_power
- using dig_port->tc_legacy_port to only execute sequences for legacy
ports, hopefully VBTs will have this right
- fixed check to call _hsw_power_well_continue_enable()
- calling _hsw_power_well_continue_enable() unconditionally in
icl_tc_phy_aux_power_well_enable(), if needed we will surpress timeout
warnings of TC legacy ports
- only blocking TC cold around fia access
v3:
- added timeout of 5msec to not loop forever if
sandybridge_pcode_write_timeout() keeps returning -EAGAIN
returning -EAGAIN in in icl_tc_cold_exit()
- removed leftover tc_cold_wakeref
- added one msec sleep when PCODE returns -EAGAIN
v4:
- removed 5msec timeout, instead giving 1msec to whoever is using
PCODE to finish it up to 3 times
- added a comment about turn TC cold exit failure as a error in future
BSpec: 21750
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1296
Cc: Imre Deak <imre.deak@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-4-jose.souza@intel.com
Moving the code to return the digital port of the aux channel also
removing the intel_phy_is_tc() to make it generic.
digital_port will be needed in icl_tc_phy_aux_power_well_enable()
so adding it as a parameter to icl_tc_port_assert_ref_held().
While at at removing the duplicated call to icl_tc_phy_aux_ch() in
icl_tc_port_assert_ref_held().
v2:
- fixed build when DRM_I915_DEBUG_RUNTIME_PM is not set
- moved to before hsw_wait_for_power_well_enable() as it will be
needed by hsw_wait_for_power_well_enable() in a future patch
v4:
- fixed action of if (!dig_port), continue instead of return
Cc: You-Sheng Yang <vicamo@gmail.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200414194956.164323-1-jose.souza@intel.com
