[ Upstream commit c894696188 ]
Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.
This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")
Thanks to Joe Perches for spotting this when I submitted an earlier patch.
Fixes: 3c05bedb5f ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b45e9d761b ]
The variable 'aa_index' is defined as an unsigned value in
update_lmb_associativity_index(), but find_aa_index() may return -1
when dlpar_clone_property() fails. So change find_aa_index() to return
a bool, which indicates whether 'aa_index' was found or not.
Fixes: c05a5a4096 ("powerpc/pseries: Dynamic add entires to associativity lookup array")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Nathan Fontenot nfont@linux.vnet.ibm.com>
[mpe: Tweak changelog, rename is_found to just found]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42885551ce ]
For each pwm output which gets enabled through pwm_lpss_apply(), we do a
pm_runtime_get_sync().
This commit adds pm_runtime_put() calls to pwm_lpss_remove() to balance
these when the driver gets removed with some of the outputs still enabled.
Fixes: f080be27d7 ("pwm: lpss: Add support for runtime PM")
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a3e71b7b7 ]
The nft_osf extension, like xt_osf, is not supported from the output
path.
Fixes: b96af92d6e ("netfilter: nf_tables: implement Passive OS fingerprint module in nft_osf")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cbca5852d ]
Fixes two problems introduced as early as
commit 03aef4b6dc ("Staging: comedi: add ni_mio_common code"):
(1) Ensures that the last four bits of NISTC_RTSI_TRIGB_OUT_REG register is
not unduly overwritten on e-series devices. On e-series devices, the
first three of the last four bits are reserved. The last bit defines
the output selection of the RGOUT0 pin, otherwise known as
RTSI_Sub_Selection. For m-series devices, these last four bits are
indeed used as the output selection of the RTSI7 pin (and the
RTSI_Sub_Selection bit for the RGOUT0 pin is moved to the
RTSI_Trig_Direction register.
(2) Allows all 4 RTSI_BRD lines to be treated as valid sources for RTSI
lines.
This patch also cleans up the ni_get_rtsi_routing command for readability.
Fixes: 03aef4b6dc ("Staging: comedi: add ni_mio_common code")
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7eeee0843 ]
With NICs that don't read the NVM directly and instead rely on getting
the relevant data from the firmware, the number of reserved MAC
addresses was not added to the API. This caused the driver to assume
there is only one address which results in all interfaces getting the
same address. Update the API to fix this.
While at it, fix-up the comments with firmware api names to actually
match what we have in the firmware.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c369c8db15 ]
A quirk in snd-usb-audio was added to automate setting sample rate to
4800k and remove the previously exposed nonfunctional microphone for
the Bowers & Wilkins PX:
commit 240a8af929https://lore.kernel.org/patchwork/patch/919689/
However the headphones where updated shortly after that to remove the
unintentional microphone functionality. I guess because of this the
headphones now crash when connecting them via USB while the quirk is
active. Dmesg:
snd-usb-audio: probe of 2-3:1.0 failed with error -22
usb 2-3: 2:1: cannot get min/max values for control 2 (id 2)
This patch removes the microfone and allows the headphones to connect
and work out of the box. It is based on the current mainline kernel
and successfully applied an tested on my machine (4.18.10.arch1-1).
Fixes: 240a8af929 ("ALSA: usb-audio: Add a quirck for B&W PX headphones")
Signed-off-by: Nicolas Huaman <nicolas@herochao.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d5a0ab1a7 ]
Commit 0413bedabc ("of: Add device_type access helper functions")
added a new helper not yet used in preparation for some treewide clean
up of accesses to 'device_type' properties. Unfortunately, there's an
error and 'type' was used for the property name. Fix this.
Fixes: 0413bedabc ("of: Add device_type access helper functions")
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfdb3be43e ]
The return from the call to _mixer_stages can be a negative error
code however this is being assigned to an unsigned variable 'stages'
hence the check is always false. Fix this by making 'stages' an
int.
Detected by Coccinelle ("Unsigned expression compared with zero:
stages < 0")
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03b2cbb6ea ]
Looks like during merging the bulk POLL* -> EPOLL* replacement
missed the patch
'commit af336cabe0 ("mei: limit the number of queued writes")'
Fix sparse warning:
drivers/misc/mei/main.c:602:13: warning: restricted __poll_t degrades to integer
drivers/misc/mei/main.c:605:30: warning: invalid assignment: |=
drivers/misc/mei/main.c:605:30: left side has type restricted __poll_t
drivers/misc/mei/main.c:605:30: right side has type int
Fixes: af336cabe0 ("mei: limit the number of queued writes")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71e5e88680 ]
Since my change to split out the regulatory init to occur later,
any issues during earlier cfg80211_init() or errors during the
platform device allocation would lead to crashes later. Make this
more robust by checking that the earlier initialization succeeded.
Fixes: d7be102f29 ("cfg80211: initialize regulatory keys/database later")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ab2b48c98 ]
The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.
Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: b504882da5 ("USB: add Freescale high-speed USB SOC device controller driver")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3def4031b3 ]
Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:
drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'
Do the same thing as OMAP and add an explicit dependency on
EXTCON.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94967b55eb ]
On a DT based system, we use the of_node full name to name the
corresponding irq domain. We expect that name to be unique, so so that
domains with the same base name won't clash (this happens on multi-node
topologies, for example).
Since a7e4cfb0a7 ("of/fdt: only store the device node basename in
full_name"), of_node_full_name() lies and only returns the basename. This
breaks the above requirement, and we end-up with only a subset of the
domains in /sys/kernel/debug/irq/domains.
Let's reinstate the feature by using the fancy new %pOF format specifier,
which happens to do the right thing.
Fixes: a7e4cfb0a7 ("of/fdt: only store the device node basename in full_name")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20181001100522.180054-3-marc.zyngier@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb50130964 ]
Since Virtual Lanes BCT credits and MTU are set through separate MADs, we
have to ensure both are valid, and data VLs are ready for transmission
before we allow port transition to Armed state.
Fixes: 5e2d6764a7 ("IB/hfi1: Verify port data VLs credits on transition to Armed")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 721ad7e643 ]
The buf is allocated by vmalloc_user in the function rxe_queue_init.
So it is better to free it by vfree.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18380dcc52 ]
The 'ret' variable is now only used in an #ifdef, and causes a
warning if it is declared outside of that block:
sound/soc/codecs/wm9712.c: In function 'wm9712_soc_probe':
sound/soc/codecs/wm9712.c:641:6: error: unused variable 'ret' [-Werror=unused-variable]
Fixes: 2ed1a8e0ce ("ASoC: wm9712: add ac97 new bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92adb74ad ]
The ia64 handling of failure to return from a signal frame has been trying
to set overlapping fields in struct siginfo since 2.3.43. The si_code
corresponds to the fields that were stomped (not the field that is
actually written), so I can not imagine a piece of userspace code
making sense of the signal frame if it looks closely.
In practice failure to return from a signal frame is a rare event that
almost never happens. Someone using an alternate signal stack to
recover and looking in detail is even more rare. So I presume no one
has ever noticed and reported this ia64 nonsense.
Sort this out by causing ia64 to use force_sig(SIGSEGV) like other architectures.
Fixes: 2.3.43
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b9c6b2831 ]
The ia64 handling of failure to setup a signal frame has been trying
to set overlapping fields in struct siginfo since 2.3.43. The si_pid
and si_uid fields are stomped when the si_addr field is set. The
si_code of SI_KERNEL indicates that si_pid and si_uid should be valid,
and that si_addr does not exist.
Being at odds with the definition of SI_KERNEL and with nothing to
indicate that this was a signal frame setup failure there is no way
for userspace to know that si_addr was filled out instead.
In practice failure to setup a signal frame is rare, and si_pid and
si_uid are always set to 0 when si_code is SI_KERNEL so I expect no
one has looked closely enough before to see this weirdness. Further
the only difference between force_sigsegv_info and the generic
force_sigsegv other than the return code is that force_sigsegv_info
stomps the si_uid and si_pid fields.
Remove the bug and simplify the code by using force_sigsegv in this
case just like other architectures.
Fixes: 2.3.43
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ff9f49646 ]
Currently the driver overwrites the surface depth provided by the fb
helper to give an invalid bpp/surface depth combination.
This has been exposed by commit 70109354fe ("drm: Reject unknown legacy
bpp and depth for drm_mode_addfb ioctl"), which now causes the driver to
fail to probe.
Fix by not overwriting the surface depth.
Fixes: d1667b8679 ("drm/hisilicon/hibmc: Add support for frame buffer")
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Xinliang Liu <z.liuxinliang@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4da6b44807 ]
Fix previous incorrect logic that limits PAXC slot number to zero only.
In order for SRIOV/VF to work, we need to allow the slot number to be
greater than zero.
Fixes: 46560388c4 ("PCI: iproc: Allow multiple devices except on PAXC")
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09ed061a4f ]
Now that the /firmware/coreboot node in DT is populated by the core DT
platform code with commit 3aa0582fdb ("of: platform: populate
/firmware/ node from of_platform_default_populate_init()") we should and
can remove the platform device creation here. Otherwise, the
of_platform_device_create() call will fail, the coreboot of driver won't
be registered, and this driver will never bind. At the same time, we
should move this driver to use MODULE_DEVICE_TABLE so that module
auto-load works properly when the coreboot device is auto-populated and
we should drop the of_node handling that was presumably placed here to
hold a reference to the DT node created during module init that no
longer happens.
Cc: Wei-Ning Huang <wnhuang@chromium.org>
Cc: Julius Werner <jwerner@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Cc: Samuel Holland <samuel@sholland.org>
Reviewed-by: Sudeep Holla <Sudeep.Holla@arm.com>
Fixes: 3aa0582fdb ("of: platform: populate /firmware/ node from of_platform_default_populate_init()")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54c2678cd1 ]
Problem:
ab460a2e72 ("rpmsg: qcom_smd: Access APCS through mailbox framework"
added a "depends on MAILBOX") to RPMSG_QCOM_SMD, thus RPMSG_QCOM_SMD
becomes unset since MAILBOX was not enabled in qcom_defconfig and is
not otherwise selected for the dragonboard. When the resulting
kernel is booted the mmc device which contains the root file system
is not available.
Fix:
add CONFIG_MAILBOX to qcom_defconfig
Fixes: ab460a2e72 ("rpmsg: qcom_smd: Access APCS through mailbox framework"
added a "depends on MAILBOX")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f8266ff58 ]
As a comment above begin_current_label_crit_section() explains,
begin_current_label_crit_section() must run in sleepable context because
when label_is_stale() is true, aa_replace_current_label() runs, which uses
prepare_creds(), which can sleep.
Until now, the ptrace access check (which runs with a task lock held)
violated this rule.
Also add a might_sleep() assertion to begin_current_label_crit_section(),
because asserts are less likely to be ignored than comments.
Fixes: b2d09ae449 ("apparmor: move ptrace checks to using labels")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b03006d5c ]
When CONFIG_X86=n function azx_snoop doesn't use the variable chip it
only returns true.
sound/pci/hda/hda_intel.c: In function ‘dma_alloc_pages’:
sound/pci/hda/hda_intel.c:2002:14: warning: unused variable ‘chip’ [-Wunused-variable]
struct azx *chip = bus_to_azx(bus);
^~~~
Create a inline function of azx_snoop.
Fixes: a41d122449 ("ALSA: hda - Embed bus into controller object")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21eab78616 ]
Position relative channel type was added in 4.19 kernel version
Fixes: "3055a6cfa04ba" ("iio: Add channel for Position Relative")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e3f2f5ece ]
The software SA record counters should not be cleared when clearing
the hardware tables. This causes the counters to be out of sync
after a driver reset.
Fixes: 63a67fe229 ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f52eb20679 ]
The cd-gpios signal is assumed active-low by the driver, and the
cd-inverted property is needed if it is, in fact, active-high. Fix
this oversight.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29feb2c960 ]
AT91_PINCTRL_OUTPUT_VAL(0) without AT91_PINCTRL_OUTPUT is a no-op, so
make sure the pins really output a zero.
Fixes: 0e43238999 ("ARM: dts: at91: add devicetree for the Axentia Nattis with Natte power")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f068435d9b upstream.
At some point in the past we needed to make sure we would get the long
name of modules and not just what we get from /proc/modules, but that
need, as described in the cset that introduced the adjustment function:
Fixes: c03d5184f0 ("perf machine: Adjust dso->long_name for offline module")
Without using the buildid-cache:
# lsmod | grep trusted
# insmod trusted.ko
# lsmod | grep trusted
trusted 24576 0
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
probe:key_seal (on key_seal in trusted)
# perf probe -l
probe:key_seal (on key_seal in trusted)
#
No attempt at opening '[trusted]'.
Now using the build-id cache:
# rmmod trusted
# perf buildid-cache --add ./trusted.ko
# insmod trusted.ko
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
#
Again, no attempt at reading '[trusted]'.
Finally, adding a probe to that function and then using:
[root@quaco ~]# perf trace -e probe_perf:*/max-stack=16/ --max-events=2
0.000 perf/13456 probe_perf:dso__adjust_kmod_long_name(__probe_ip: 5492263)
dso__adjust_kmod_long_name (/home/acme/bin/perf)
machine__process_kernel_mmap_event (/home/acme/bin/perf)
machine__process_mmap_event (/home/acme/bin/perf)
perf_event__process_mmap (/home/acme/bin/perf)
machines__deliver_event (/home/acme/bin/perf)
perf_session__deliver_event (/home/acme/bin/perf)
perf_session__process_event (/home/acme/bin/perf)
process_simple (/home/acme/bin/perf)
reader__process_events (/home/acme/bin/perf)
__perf_session__process_events (/home/acme/bin/perf)
perf_session__process_events (/home/acme/bin/perf)
process_buildids (/home/acme/bin/perf)
record__finish_output (/home/acme/bin/perf)
__cmd_record (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
0.055 perf/13456 probe_perf:dso__adjust_kmod_long_name(__probe_ip: 5492263)
dso__adjust_kmod_long_name (/home/acme/bin/perf)
machine__process_kernel_mmap_event (/home/acme/bin/perf)
machine__process_mmap_event (/home/acme/bin/perf)
perf_event__process_mmap (/home/acme/bin/perf)
machines__deliver_event (/home/acme/bin/perf)
perf_session__deliver_event (/home/acme/bin/perf)
perf_session__process_event (/home/acme/bin/perf)
process_simple (/home/acme/bin/perf)
reader__process_events (/home/acme/bin/perf)
__perf_session__process_events (/home/acme/bin/perf)
perf_session__process_events (/home/acme/bin/perf)
process_buildids (/home/acme/bin/perf)
record__finish_output (/home/acme/bin/perf)
__cmd_record (/home/acme/bin/perf)
cmd_record (/home/acme/bin/perf)
run_builtin (/home/acme/bin/perf)
#
This was the only path I could find using the perf tools that reach at this
function, then as of november/2019, if we put a probe in the line where the
actuall setting of the dso->long_name is done:
# perf trace -e probe_perf:*
^C[root@quaco ~]
# perf stat -e probe_perf:* -I 2000
2.000404265 0 probe_perf:dso__adjust_kmod_long_name
4.001142200 0 probe_perf:dso__adjust_kmod_long_name
6.001704120 0 probe_perf:dso__adjust_kmod_long_name
8.002398316 0 probe_perf:dso__adjust_kmod_long_name
10.002984010 0 probe_perf:dso__adjust_kmod_long_name
12.003597851 0 probe_perf:dso__adjust_kmod_long_name
14.004113303 0 probe_perf:dso__adjust_kmod_long_name
16.004582773 0 probe_perf:dso__adjust_kmod_long_name
18.005176373 0 probe_perf:dso__adjust_kmod_long_name
20.005801605 0 probe_perf:dso__adjust_kmod_long_name
22.006467540 0 probe_perf:dso__adjust_kmod_long_name
^C 23.683261941 0 probe_perf:dso__adjust_kmod_long_name
#
Its not being used at all.
To further test this I used kvm.ko as the offline module, i.e. removed
if from the buildid-cache by nuking it completely (rm -rf ~/.debug) and
moved it from the normal kernel distro path, removed the modules, stoped
the kvm guest, and then installed it manually, etc.
# rmmod kvm-intel
# rmmod kvm
# lsmod | grep kvm
# modprobe kvm-intel
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: could not insert 'kvm_intel': Unknown symbol in module, or unknown parameter (see dmesg)
# insmod ./kvm.ko
# modprobe kvm-intel
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
# lsmod | grep kvm
kvm_intel 299008 0
kvm 765952 1 kvm_intel
irqbypass 16384 1 kvm
#
# perf probe -x ~/bin/perf machine__findnew_module_map:12 mname=m.name:string filename=filename:string 'dso_long_name=map->dso->long_name:string' 'dso_name=map->dso->name:string'
# perf probe -l
probe_perf:machine__findnew_module_map (on machine__findnew_module_map:12@util/machine.c in /home/acme/bin/perf with mname filename dso_long_name dso_name)
# perf record
^C[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 3.416 MB perf.data (33956 samples) ]
# perf trace -e probe_perf:machine*
<SNIP>
6.322 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[salsa20_generic]", filename: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_long_name: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_name: "[salsa20_generic]")
6.375 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[kvm]", filename: "[kvm]", dso_long_name: "[kvm]", dso_name: "[kvm]")
<SNIP>
The filename doesn't come with the path, no point in trying to set the dso->long_name.
[root@quaco ~]# strace -e open,openat perf probe -m ./kvm.ko kvm_apic_local_deliver |& egrep 'open.*kvm'
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/kvm/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm", O_RDONLY|O_NONBLOCK|O_CLOEXEC|O_DIRECTORY) = 7
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 8
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/kvm.ko/5955f426cb93f03f30f3e876814be2db80ab0b55/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
[root@quaco ~]#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-jlfew3lyb24d58egrp0o72o2@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1d787bceb upstream.
When testing BigEndian kernel, the sun4i-ss was failling all crypto
tests.
This patch fix endian issues with it.
Fixes: 6298e94821 ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15e14f76f8 upstream.
Fix bbp ready check in mt7601u_wait_bbp_ready. The issue is reported by
coverity with the following error:
Logical vs. bitwise operator
The expression's value does not depend on the operands; inadvertent use
of the wrong operator is a likely logic error.
Addresses-Coverity-ID: 1309441 ("Logical vs. bitwise operator")
Fixes: c869f77d6a ("add mt7601u driver")
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12db3c8083 upstream.
In function __tipc_shutdown(), the timeout value passed to
tipc_wait_for_cond() is not jiffies.
This commit fixes it by converting that value from milliseconds
to jiffies.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46cb01eeeb upstream.
In commit 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address
hash values"), the 32-bit node address only generated after one second
trial period expired. However the self's addr in struct tipc_monitor do
not update according to node address generated. This lead to it is
always zero as initial value. As result, sorting algorithm using this
value does not work as expected, neither neighbor monitoring framework.
In this commit, we add a fix to update self's addr when 32-bit node
address generated.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6afd1234c upstream.
Commit 01c9348c76
powerpc: Use hardware RNG for arch_get_random_seed_* not arch_get_random_*
updated arch_get_random_[int|long]() to be NOPs, and moved the hardware
RNG backing to arch_get_random_seed_[int|long]() instead. However, it
failed to take into account that arch_get_random_int() was implemented
in terms of arch_get_random_long(), and so we ended up with a version
of the former that is essentially a NOP as well.
Fix this by calling arch_get_random_seed_long() from
arch_get_random_seed_int() instead.
Fixes: 01c9348c76 ("powerpc: Use hardware RNG for arch_get_random_seed_* not arch_get_random_*")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191204115015.18015-1-ardb@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5866efa8cb upstream.
gss_read_proxy_verf() assumes things about the XDR buffer containing
the RPC Call that are not true for buffers generated by
svc_rdma_recv().
RDMA's buffers look more like what the upper layer generates for
sending: head is a kmalloc'd buffer; it does not point to a page
whose contents are contiguous with the first page in the buffers'
page array. The result is that ACCEPT_SEC_CONTEXT via RPC/RDMA has
stopped working on Linux NFS servers that use gssproxy.
This does not affect clients that use only TCP to send their
ACCEPT_SEC_CONTEXT operation (that's all Linux clients). Other
clients, like Solaris NFS clients, send ACCEPT_SEC_CONTEXT on the
same transport as they send all other NFS operations. Such clients
can send ACCEPT_SEC_CONTEXT via RPC/RDMA.
I thought I had found every direct reference in the server RPC code
to the rqstp->rq_pages field.
Bug found at the 2019 Westford NFS bake-a-thon.
Fixes: 3316f06311 ("svcrdma: Persistently allocate and DMA- ... ")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Bill Baker <bill.baker@oracle.com>
Reviewed-by: Simo Sorce <simo@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f31bc67e4 upstream.
It turned out Intel Gemini Lake doesn't use the same I2C timing
parameters as Broxton.
I got confirmation from the Windows team that Gemini Lake systems should
use updated timing parameters that differ from those used in Broxton
based systems.
Fixes: f80e78aa11 ("mfd: intel-lpss: Add Intel Gemini Lake PCI IDs")
Tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7787657d7e upstream.
Fix a typo in the free slave id search loop. Instead of I2C_CLIENT_PEC,
it should have been I2C_CLIENT_TEN. The slave id 1 can only handle 7-bit
addresses and thus is not eligible in case of 10-bit addresses.
As a matter of fact none of the slave id support I2C_CLIENT_PEC, overall
check is performed at the beginning of the stm32f7_i2c_reg_slave function.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d3be711e upstream.
The IP can handle two slave addresses. One address can either be
7 bits or 10 bits while the other can only be 7 bits.
In order to ensure that a 10 bits address can always be allocated
(assuming there is only one 7 bits address already allocated),
pick up the 7-bits only address slot in priority when performing a 7-bits
address allocation.
Fixes: 60d609f30d ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
