Merge "ARM: rockchip: dts changes for 4.1" from Heiko Stuebner:
This adds and enables the usbphy nodes on the rk3288 boards and enables
the gmac on the firefly board. A new board the Popmetal-rk3288 is also
added. And finally the pmic supplies for act8846 based boards are added,
as the act8865/act8846 driver gained supply handling in the regulator tree.
* tag 'v4.1-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: complete rk3288-evb pmic supplies
ARM: dts: rockchip: add input supplies for the act8846 on Radxa Rock
ARM: dts: add rk3288 PopMetal board
dt-bindings: add root compatible property for PopMetal board
ARM: dts: rockchip: enable gmac on rk3288-firefly
ARM: dts: rockchip: enable usbphy on rk3288-firefly
ARM: dts: rockchip: Enable usb PHY on rk3288-evb board
ARM: dts: rockchip: add rk3288 usb PHY
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull "This pull request contains the following changes from Ray for Cygnus SoCs: from Florian Fainelli:
- enable IOMUX, required for pinmux/pinctrl
- enable GPIO, required for the GPIO driver
- enable GPIO hook detection for BCM911360-based phone designs
- enable PCIe controller for the bcm958300k designs
* tag 'arm-soc/for-4.1/devicetree-part-2' of http://github.com/broadcom/stblinux:
ARM: dts: enable PCIe support for Cygnus
ARM: dts: cygnus: enable GPIO based hook detection
ARM: dts: enable GPIO for Broadcom Cygnus
ARM: dts: enable IOMUX for Broadcom Cygnus
This patch introduces devicetree for the Alpine platform, and
for a development board based on the same platform.
Signed-off-by: Barak Wasserstrom <barak@annapurnalabs.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there.
Only enable them for bcm958300k where PCIe interfaces are populated
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the static vcc_sys regulator to the rk3288-evb, the missing
rk808 supplies from it and all the supplies of the act8846 evb-variant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull "mvebu dt changes for v4.1 (part #1)" from Gregory CLEMENT:
- fix SDHCI nodes on Armada 38x
- add Linksys WRT1900AC (Mamba) support (including the Ethernet switch)
- add several fixes and improvement for dove
- enable GPIO fan alarm support for 2Big Network v2
- add several fixes about unit address
- add support for Armada 39x SoC and board
* tag 'mvebu-dt-4.1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add Device Tree files for Armada 39x SoC and board
ARM: mvebu: fix unit address of MPIC nodes
ARM: mvebu: use stdout-path in all armada-*.dts
ARM: mvebu: add serial port aliases on Armada 370/375/38x/XP
ARM: mvebu: remove aliases for Ethernet devices on Armada 370/375/38x/XP
ARM: mvebu: add UART labels to Armada 375
ARM: mvebu: add missing UART labels on Armada 38x
ARM: mvebu: fix usb@ unit address on Armada 38x to match register address
ARM: mvebu: a385-db-ap: Enable the NAND
ARM: ARMADA XP: WRT1900AC: Add support for the Ethernet switch
ARM: Kirkwood: enable GPIO fan alarm support for 2Big Network v2
ARM: mvebu: Fix MPIC unit address
ARM: dts: dove: Add some more common pinctrl settings
ARM: dts: dove: Add node labels for PCIe ports 0 and 1
ARM: dts: dove: Always include gpio and interrupt-controller headers
ARM: dts: dove: Fix uart[23] reg property
ARM: mvebu: add Linksys WRT1900AC (Mamba) support
ARM: mvebu: Add Device Tree description of SDHCI for Armada 388 RD
ARM: mvebu: Update the SDHCI node on Armada 38x
ARM: mvebu: Use macros for interrupt flags on Armada 38x sdhci node
Pull "Broadcom Device Tree changes for 4.1 #1" from Florian Fainelli:
This pull request contains the following Broadcom SoCs Device Tree changes:
- Jonathan adds support for the Broadcom Cygnus BCM958305K board
- Rafal adds support for Netgear R8000 and fixes the default for power LEDs
on Netgear R6250
* tag 'arm-soc/for-4.1/devicetree' of http://github.com/broadcom/stblinux:
ARM: BCM5301X: Fix default state of power LEDs on Netgear R6250
ARM: BCM5301X: Add DT for Netgear R8000
ARM: dts: Enable Broadcom Cygnus BCM958305K
On the Radxa Rock board most supplies come from the static 5v vsys supply, but
the inl1-supply comes from the REG4 of the act8846 itself. Model this dependency
using the added supply-handling to make sure the supplying regulator gets handled
correctly and not accidentially turned off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The switches on r8a73a4/ape6evm do not have pull-up registers. The
schematics say: "Need to use APE6 internal PullUp", hence enable pull-up
using pinctrl.
Without this, the switches don't really work, as the GPIO inputs are
more likely to pick up ghost signals through capacitive coupling than
actual keypresses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).
This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PopMetal board is a rk3288 based board made by ChipSpark, this
add root compatible property for it
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.
Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.
So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC, L2 cache
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
controller, MPIC interrupt controller, timer, CPU reset for SMP,
PMSU.
* I2C
* SPI
* SDHCI
* XOR
* NAND
* UART
* PCIe
Additional features will be supported in the future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
First fixes batch for AT91 on 4.0:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
The Device Tree nodes describing the MPIC nodes on Armada 370, 375,
38x and XP had a unit address that did not match the first reg
property, as suggested by the ePAPR. This commit fixes that.
[gregory.clement@free-electrons.com: removed the armada-38x part, as it
was already applied by a previous patch]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the stdout-path property in /chosen for all Armada
boards that were not yet carrying this property, and gets rid of
/chosen/bootargs which becomes unneeded: earlyprintk should not be
used by default, and the console= parameter is replaced by the
/chosen/stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds 'serialX' aliases for the various serial ports on
Armada 370, 375, 38x and XP platforms. It will allow the usage of the
stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Having aliases for Ethernet devices is useless, since the networking
subsystem unfortunately doesn't care about aliases to name network
interfaces.
Note that the 'aliases' nodes in armada-370-xp.dtsi and armada-xp.dtsi
become empty, but that we keep it as is since a followup patch will
re-add some aliases to it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
