commit 50ff57888d upstream.
On a zoned filesystem, if we fail to allocate the root node for the log
root tree while syncing the log, we end up returning without finishing
the IO plug we started before, resulting in leaking resources as we
have started writeback for extent buffers of a log tree before. That
allocation failure, which typically is either -ENOMEM or -ENOSPC, is not
fatal and the fsync can safely fallback to a full transaction commit.
So release the IO plug if we fail to allocate the extent buffer for the
root of the log root tree when syncing the log on a zoned filesystem.
Fixes: 3ddebf27fc ("btrfs: zoned: reorder log node allocation on zoned filesystem")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fc45e55ebc upstream.
The "safe state" index is used by acpi_idle_enter_bm() to avoid
entering a C-state that may require bus mastering to be disabled
on entry in the cases when this is not going to happen. For this
reason, it should not be set to point to C3 type of C-states, because
they may require bus mastering to be disabled on entry in principle.
This was broken by commit d6b88ce2eb ("ACPI: processor idle: Allow
playing dead in C3 state") which inadvertently allowed the "safe
state" index to point to C3 type of C-states.
This results in a machine that won't boot past the point when it first
enters C3. Restore the correct behaviour (either demote to C1/C2, or
use C3 but also set ARB_DIS=1).
I hit this on a Fujitsu Siemens Lifebook S6010 (P3) machine.
Fixes: d6b88ce2eb ("ACPI: processor idle: Allow playing dead in C3 state")
Cc: 5.16+ <stable@vger.kernel.org> # 5.16+
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Woody Suwalski <wsuwalski@gmail.com>
[ rjw: Subject and changelog adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ddffdb944 upstream.
The commit referenced below fixed packet re-routing if Netfilter mangles
a routing key property of a packet and the packet is routed in a VRF L3
domain. The fix, however, addressed IPv4 re-routing, only.
This commit applies the same behavior for IPv6. While at it, untangle
the nested ternary operator to make the code more readable.
Fixes: 6d8b49c3a3 ("netfilter: Update ip_route_me_harder to consider L3 domain")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba7542eb2d upstream.
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31fa985b41 upstream.
kasan_quarantine_remove_cache() is called in kmem_cache_shrink()/
destroy(). The kasan_quarantine_remove_cache() call is protected by
cpuslock in kmem_cache_destroy() to ensure serialization with
kasan_cpu_offline().
However the kasan_quarantine_remove_cache() call is not protected by
cpuslock in kmem_cache_shrink(). When a CPU is going offline and cache
shrink occurs at same time, the cpu_quarantine may be corrupted by
interrupt (per_cpu_remove_cache operation).
So add a cpu_quarantine offline flags check in per_cpu_remove_cache().
[akpm@linux-foundation.org: add comment, per Zqiang]
Link: https://lkml.kernel.org/r/20220414025925.2423818-1-qiang1.zhang@intel.com
Signed-off-by: Zqiang <qiang1.zhang@intel.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1da18a296f upstream.
The mount option "explicit_open" manages the device open zone
resources to ensure that if an application opens a sequential file for
writing, the file zone can always be written by explicitly opening
the zone and accounting for that state with the s_open_zones counter.
However, if some zones are already open when mounting, the device open
zone resource usage status will be larger than the initial s_open_zones
value of 0. Ensure that this inconsistency does not happen by closing
any sequential zone that is open when mounting.
Furthermore, with ZNS drives, closing an explicitly open zone that has
not been written will change the zone state to "closed", that is, the
zone will remain in an active state. Since this can then cause failures
of explicit open operations on other zones if the drive active zone
resources are exceeded, we need to make sure that the zone is not
active anymore by resetting it instead of closing it. To address this,
zonefs_zone_mgmt() is modified to change a REQ_OP_ZONE_CLOSE request
into a REQ_OP_ZONE_RESET for sequential zones that have not been
written.
Fixes: b5c00e9757 ("zonefs: open/close zone on file open/close")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18d609daa5 ]
Because mremap does not have a MAP_FIXED_NOREPLACE flag, it can destroy
existing mappings. This causes a segfault when regions such as text are
remapped and the permissions are changed.
Verify the requested mremap destination address does not overlap any
existing mappings by using mmap's MAP_FIXED_NOREPLACE flag. Keep
incrementing the destination address until a valid mapping is found or
fail the current test once the max address is reached.
Link: https://lkml.kernel.org/r/20220420215721.4868-2-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c85a9bae2 ]
Avoid calling mmap with requested addresses that are less than the
system's mmap_min_addr. When run as root, mmap returns EACCES when
trying to map addresses < mmap_min_addr. This is not one of the error
codes for the condition to retry the mmap in the test.
Rather than arbitrarily retrying on EACCES, don't attempt an mmap until
addr > vm.mmap_min_addr.
Add a munmap call after an alignment check as the mappings are retained
after the retry and can reach the vm.max_map_count sysctl.
Link: https://lkml.kernel.org/r/20220420215721.4868-1-sidhartha.kumar@oracle.com
Signed-off-by: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb82c57469 ]
The "read_bhrb" global symbol is only called under CONFIG_PPC64 of
arch/powerpc/perf/core-book3s.c but it is compiled for both 32 and 64 bit
anyway (and LLVM fails to link this on 32bit).
This fixes it by moving bhrb.o to obj64 targets.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220421025756.571995-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc6de28784 ]
There is a deadlock in rr_close(), which is shown below:
(Thread 1) | (Thread 2)
| rr_open()
rr_close() | add_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | rr_timer()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5d0f921ea ]
because the copychunk_write might cover a region of the file that has not yet
been sent to the server and thus fail.
A simple way to reproduce this is:
truncate -s 0 /mnt/testfile; strace -f -o x -ttT xfs_io -i -f -c 'pwrite 0k 128k' -c 'fcollapse 16k 24k' /mnt/testfile
the issue is that the 'pwrite 0k 128k' becomes rearranged on the wire with
the 'fcollapse 16k 24k' due to write-back caching.
fcollapse is implemented in cifs.ko as a SMB2 IOCTL(COPYCHUNK_WRITE) call
and it will fail serverside since the file is still 0b in size serverside
until the writes have been destaged.
To avoid this we must ensure that we destage any unwritten data to the
server before calling COPYCHUNK_WRITE.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1997373
Reported-by: Xiaoli Feng <xifeng@redhat.com>
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6823e4e36 ]
The first "if" condition in __memcpy_flushcache is supposed to align the
"dest" variable to 8 bytes and copy data up to this alignment. However,
this condition may misbehave if "size" is greater than 4GiB.
The statement min_t(unsigned, size, ALIGN(dest, 8) - dest); casts both
arguments to unsigned int and selects the smaller one. However, the
cast truncates high bits in "size" and it results in misbehavior.
For example:
suppose that size == 0x100000001, dest == 0x200000002
min_t(unsigned, size, ALIGN(dest, 8) - dest) == min_t(0x1, 0xe) == 0x1;
...
dest += 0x1;
so we copy just one byte "and" dest remains unaligned.
This patch fixes the bug by replacing unsigned with size_t.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49aefd1317 ]
Commit b5f862180d was introduced to discard lowest hash bit for layer3+4 hashing
but it also removes last bit from non layer3+4 hashing
Below script shows layer2+3 hashing will result in same slave to be used with above commit.
$ cat hash.py
#/usr/bin/python3.6
h_dests=[0xa0, 0xa1]
h_source=0xe3
hproto=0x8
saddr=0x1e7aa8c0
daddr=0x17aa8c0
for h_dest in h_dests:
hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
hash ^= hash >> 16
hash ^= hash >> 8
print(hash)
print("with last bit removed")
for h_dest in h_dests:
hash = (h_dest ^ h_source ^ hproto ^ saddr ^ daddr)
hash ^= hash >> 16
hash ^= hash >> 8
hash = hash >> 1
print(hash)
Output:
$ python3.6 hash.py
522133332
522133333 <-------------- will result in both slaves being used
with last bit removed
261066666
261066666 <-------------- only single slave used
Signed-off-by: suresh kumar <suresh2514@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02655a70b7 ]
Currently ksmbd is using ->f_bsize from vfs_statfs() as sector size.
If fat/exfat is a local share, ->f_bsize is a cluster size that is too
large to be used as a sector size. Sector sizes larger than 4K cause
problem occurs when mounting an iso file through windows client.
The error message can be obtained using Mount-DiskImage command,
the error is:
"Mount-DiskImage : The sector size of the physical disk on which the
virtual disk resides is not supported."
This patch reports fixed 4KB sector size if ->s_blocksize is bigger
than 4KB.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb5adc7075 ]
There is a deadlock in rs_close(), which is shown
below:
(Thread 1) | (Thread 2)
| rs_open()
rs_close() | mod_timer()
spin_lock_bh() //(1) | (wait a time)
... | rs_poll()
del_timer_sync() | spin_lock() //(2)
(wait timer to stop) | ...
We hold timer_lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need timer_lock in position (2) of thread 2.
As a result, rs_close() will block forever.
This patch deletes the redundant timer_lock in order to
prevent the deadlock. Because there is no race condition
between rs_close, rs_open and rs_poll.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Message-Id: <20220407154430.22387-1-duoming@zju.edu.cn>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92ccbf17ee ]
When the driver fails during probing, the driver should disable the
regulator, not just handle it in wm8731_hw_init().
The following log reveals it:
[ 17.812483] WARNING: CPU: 1 PID: 364 at drivers/regulator/core.c:2257 _regulator_put+0x3ec/0x4e0
[ 17.815958] RIP: 0010:_regulator_put+0x3ec/0x4e0
[ 17.824467] Call Trace:
[ 17.824774] <TASK>
[ 17.825040] regulator_bulk_free+0x82/0xe0
[ 17.825514] devres_release_group+0x319/0x3d0
[ 17.825882] i2c_device_probe+0x766/0x940
[ 17.829198] i2c_register_driver+0xb5/0x130
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220405121038.4094051-1-zheyuma97@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aeaf59b787 ]
This reverts commit 723ad91613
When client requests channel or ring size larger than what the server
can support the server will cap the request to the supported max. So,
the client would not be able to successfully request resources that
exceed the server limit.
Fixes: 723ad91613 ("ibmvnic: Add ethtool private flag for driver-defined queue limits")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220427235146.23189-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 296abc0d91 ]
Commit 00bfe02f47 ("gfs2: Fix mmap + page fault deadlocks for buffered
I/O") changed gfs2_file_read_iter() and gfs2_file_buffered_write() to
allow dropping the inode glock while faulting in user buffers. When the
lock was dropped, a short result was returned to indicate that the
operation was interrupted.
As pointed out by Linus (see the link below), this behavior is broken
and the operations should always re-acquire the inode glock and resume
the operation instead.
Link: https://lore.kernel.org/lkml/CAHk-=whaz-g_nOOoo8RRiWNjnv2R+h6_xk2F1J4TuSRxk1MtLw@mail.gmail.com/
Fixes: 00bfe02f47 ("gfs2: Fix mmap + page fault deadlocks for buffered I/O")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bde4c4858 ]
When direct writes fail with -ENOTBLK because we're writing into a
hole (gfs2_iomap_begin()) or because of a page invalidation failure
(iomap_dio_rw()), we're falling back to buffered writes. In that case,
when we lose the inode glock in gfs2_file_buffered_write(), we want to
re-acquire it instead of returning a short write.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 124c458a40 ]
Clean up the retry logic in the read and write functions somewhat.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554c577cee ]
Currently, instead of performing a short write,
iomap_file_buffered_write will fail when part of its iov iterator cannot
be read. In contrast, gfs2_file_buffered_write will loop around if it
can read part of the iov iterator, so we can end up in an endless loop.
This should be fixed in iomap_file_buffered_write (and also
generic_perform_write), but this comes a bit late in the 5.16
development cycle, so work around it in the filesystem by
trimming the iov iterator to the known-good size for now.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0df71948e ]
Calling tls_append_frag when max_open_record_len == record->len might
add an empty fragment to the TLS record if the call happens to be on the
page boundary. Normally tls_append_frag coalesces the zero-sized
fragment to the previous one, but not if it's on page boundary.
If a resync happens then, the mlx5 driver posts dump WQEs in
tx_post_resync_dump, and the empty fragment may become a data segment
with byte_count == 0, which will confuse the NIC and lead to a CQE
error.
This commit fixes the described issue by skipping tls_append_frag on
zero size to avoid adding empty fragments. The fix is not in the driver,
because an empty fragment is hardly the desired behavior.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220426154949.159055-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c6b6e18c8 ]
dqm->gws_queue_count and pdd->qpd.mapped_gws_queue need to be updated
each time the queue gets evicted.
Fixes: b8020b0304 ("drm/amdkfd: Enable over-subscription with >1 GWS queue")
Signed-off-by: David Yat Sin <david.yatsin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 626873c446 ]
`nf_flowtable_udp_timeout` sysctl option is available only
if CONFIG_NFT_FLOW_OFFLOAD enabled. But infra for this flow
offload UDP timeout was added under CONFIG_NF_FLOW_TABLE
config option. So, if you have CONFIG_NFT_FLOW_OFFLOAD
disabled and CONFIG_NF_FLOW_TABLE enabled, the
`nf_flowtable_udp_timeout` is not present in sysfs.
Please note, that TCP flow offload timeout sysctl option
is present even CONFIG_NFT_FLOW_OFFLOAD is disabled.
I suppose it was a typo in commit that adds UDP flow offload
timeout and CONFIG_NF_FLOW_TABLE should be used instead.
Fixes: 975c57504d ("netfilter: conntrack: Introduce udp offload timeout configuration")
Signed-off-by: Volodymyr Mytnyk <volodymyr.mytnyk@plvision.eu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a1e99b61b ]
We should check unused fields for non-zero and -EINVAL if they are set,
making it consistent with other opcodes.
Fixes: aa1fa28fc7 ("io_uring: add support for recvmsg()")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 588faa1ea5 ]
We should check unused fields for non-zero and -EINVAL if they are set,
making it consistent with other opcodes.
Fixes: 0fa03c624d ("io_uring: add support for sendmsg()")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71cffebf63 ]
Commit 4b5923249b ("net: dsa: lantiq_gswip: Configure all remaining
GSWIP_MII_CFG bits") added all known bits in the GSWIP_MII_CFGp
register. It helped bring this register into a well-defined state so the
driver has to rely less on the bootloader to do things right.
Unfortunately it also sets the GSWIP_MII_CFG_RMII_CLK bit without any
possibility to configure it. Upon further testing it turns out that all
boards which are supported by the GSWIP driver in OpenWrt which use an
RMII PHY have a dedicated oscillator on the board which provides the
50MHz RMII reference clock.
Don't set the GSWIP_MII_CFG_RMII_CLK bit (but keep the code which always
clears it) to fix support for the Fritz!Box 7362 SL in OpenWrt. This is
a board with two Atheros AR8030 RMII PHYs. With the "RMII clock" bit set
the MAC also generates the RMII reference clock whose signal then
conflicts with the signal from the oscillator on the board. This results
in a constant cycle of the PHY detecting link up/down (and as a result
of that: the two ports using the AR8030 PHYs are not working).
At the time of writing this patch there's no known board where the MAC
(GSWIP) has to generate the RMII reference clock. If needed this can be
implemented in future by providing a device-tree flag so the
GSWIP_MII_CFG_RMII_CLK bit can be toggled per port.
Fixes: 4b5923249b ("net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits")
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20220425152027.2220750-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc3ae06c5f ]
commit b4bdc4fbf8 ("soc: sunxi: Deal with the MBUS DMA offsets in a
central place") added a platform device notifier that sets the DMA
offset for all of the display engine frontend and backend devices.
The code applying the offset to DMA buffer physical addresses was then
removed from the backend driver in commit 756668ba68 ("drm/sun4i:
backend: Remove the MBUS quirks"), but the code subtracting PHYS_OFFSET
was left in the frontend driver.
As a result, the offset was applied twice in the frontend driver. This
likely went unnoticed because it only affects specific configurations
(scaling or certain pixel formats) where the frontend is used, on boards
with both one of these older SoCs and more than 1 GB of DRAM.
In addition, the references to PHYS_OFFSET prevent compiling the driver
on architectures where PHYS_OFFSET is not defined.
Fixes: b4bdc4fbf8 ("soc: sunxi: Deal with the MBUS DMA offsets in a central place")
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220424162633.12369-4-samuel@sholland.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24cbdb910b ]
The other port_hidden functions rely on the port_read/port_write
functions to access the hidden control port. These functions apply the
offset for port_base_addr where applicable. Update port_hidden_wait to
use the port_wait_bit so that port_base_addr offsets are accounted for
when waiting for the busy bit to change.
Without the offset the port_hidden_wait function would timeout on
devices that have a non-zero port_base_addr (e.g. MV88E6141), however
devices that have a zero port_base_addr would operate correctly (e.g.
MV88E6390).
Fixes: 609070133a ("net: dsa: mv88e6xxx: update code operating on hidden registers")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220425070454.348584-1-nathan@nathanrossi.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acac0541d1 ]
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com
Fixes: d03825fba4 ("net: bcmgenet: add skb_tx_timestamp call")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4e6448638 ]
It's noted that dcvs interrupts are not self-clearing, thus an interrupt
handler runs constantly, which leads to a severe regression in runtime.
To fix the problem an explicit write to clear interrupt register is
required, note that on OSM platforms the register may not be present.
Fixes: 275157b367 ("cpufreq: qcom-cpufreq-hw: Add dcvs interrupt support")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
