commit a26c56ae67 upstream.
Use the `marvell,reg-init` DT property to configure the LED[2]/INTn pin
of the Marvell 88E1514 ethernet PHY on Turris Omnia into interrupt mode.
Without this the pin is by default in LED[2] mode, and the Marvell PHY
driver configures LED[2] into "On - Link, Blink - Activity" mode.
This fixes the issue where the pca9538 GPIO/interrupt controller (which
can't mask interrupts in HW) received too many interrupts and after a
time started ignoring the interrupt with error message:
IRQ 71: nobody cared
There is a work in progress to have the Marvell PHY driver support
parsing PHY LED nodes from OF and registering the LEDs as Linux LED
class devices. Once this is done the PHY driver can also automatically
set the pin into INTn mode if it does not find LED[2] in OF.
Until then, though, we fix this via `marvell,reg-init` DT property.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: 26ca8b52d6 ("ARM: dts: add support for Turris Omnia")
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d473d32c2f upstream.
[<vendor>,]nr-gpios property is used by some GPIO drivers[0] to indicate
the number of GPIOs present on a system, not define a GPIO. nr-gpios is
not configured by #gpio-cells and can't be parsed along with other
"*-gpios" properties.
nr-gpios without the "<vendor>," prefix is not allowed by the DT
spec[1], so only add exception for the ",nr-gpios" suffix and let the
error message continue being printed for non-compliant implementations.
[0] nr-gpios is referenced in Documentation/devicetree/bindings/gpio:
- gpio-adnp.txt
- gpio-xgene-sb.txt
- gpio-xlp.txt
- snps,dw-apb-gpio.yaml
[1] Link: cb53a16a1e/schemas/gpio/gpio-consumer.yaml (L20)
Fixes errors such as:
OF: /palmbus@300000/gpio@600: could not find phandle
Fixes: 7f00be96f1 ("of: property: Add device link support for interrupt-parent, dmas and -gpio(s)")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Saravana Kannan <saravanak@google.com>
Cc: stable@vger.kernel.org # v5.5+
Link: https://lore.kernel.org/r/20210405222540.18145-1-ilya.lipnitskiy@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df41872b68 upstream.
I encountered a hung task issue, but not a performance one. I run DIO
on a device (need lba continuous, for example open channel ssd), maybe
hungtask in below case:
DIO: Checkpoint:
get addr A(at boundary), merge into BIO,
no submit because boundary missing
flush dirty data(get addr A+1), wait IO(A+1)
writeback timeout, because DIO(A) didn't submit
get addr A+2 fail, because checkpoint is doing
dio_send_cur_page() may clear sdio->boundary, so prevent it from missing
a boundary.
Link: https://lkml.kernel.org/r/20210322042253.38312-1-jack.qiu@huawei.com
Fixes: b1058b9812 ("direct-io: submit bio after boundary buffer is added to it")
Signed-off-by: Jack Qiu <jack.qiu@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90bd070aae upstream.
The following deadlock is detected:
truncate -> setattr path is waiting for pending direct IO to be done (inode->i_dio_count become zero) with inode->i_rwsem held (down_write).
PID: 14827 TASK: ffff881686a9af80 CPU: 20 COMMAND: "ora_p005_hrltd9"
#0 __schedule at ffffffff818667cc
#1 schedule at ffffffff81866de6
#2 inode_dio_wait at ffffffff812a2d04
#3 ocfs2_setattr at ffffffffc05f322e [ocfs2]
#4 notify_change at ffffffff812a5a09
#5 do_truncate at ffffffff812808f5
#6 do_sys_ftruncate.constprop.18 at ffffffff81280cf2
#7 sys_ftruncate at ffffffff81280d8e
#8 do_syscall_64 at ffffffff81003949
#9 entry_SYSCALL_64_after_hwframe at ffffffff81a001ad
dio completion path is going to complete one direct IO (decrement
inode->i_dio_count), but before that it hung at locking inode->i_rwsem:
#0 __schedule+700 at ffffffff818667cc
#1 schedule+54 at ffffffff81866de6
#2 rwsem_down_write_failed+536 at ffffffff8186aa28
#3 call_rwsem_down_write_failed+23 at ffffffff8185a1b7
#4 down_write+45 at ffffffff81869c9d
#5 ocfs2_dio_end_io_write+180 at ffffffffc05d5444 [ocfs2]
#6 ocfs2_dio_end_io+85 at ffffffffc05d5a85 [ocfs2]
#7 dio_complete+140 at ffffffff812c873c
#8 dio_aio_complete_work+25 at ffffffff812c89f9
#9 process_one_work+361 at ffffffff810b1889
#10 worker_thread+77 at ffffffff810b233d
#11 kthread+261 at ffffffff810b7fd5
#12 ret_from_fork+62 at ffffffff81a0035e
Thus above forms ABBA deadlock. The same deadlock was mentioned in
upstream commit 28f5a8a7c0 ("ocfs2: should wait dio before inode lock
in ocfs2_setattr()"). It seems that that commit only removed the
cluster lock (the victim of above dead lock) from the ABBA deadlock
party.
End-user visible effects: Process hang in truncate -> ocfs2_setattr path
and other processes hang at ocfs2_dio_end_io_write path.
This is to fix the deadlock itself. It removes inode_lock() call from
dio completion path to remove the deadlock and add ip_alloc_sem lock in
setattr path to synchronize the inode modifications.
[wen.gang.wang@oracle.com: remove the "had_alloc_lock" as suggested]
Link: https://lkml.kernel.org/r/20210402171344.1605-1-wen.gang.wang@oracle.com
Link: https://lkml.kernel.org/r/20210331203654.3911-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad1e36616 upstream.
ia64 has two stacks:
- memory stack (or stack), pointed at by by r12
- register backing store (register stack), pointed at by
ar.bsp/ar.bspstore with complications around dirty
register frame on CPU.
In [1] Dmitry noticed that PTRACE_GET_SYSCALL_INFO returns the register
stack instead memory stack.
The bug comes from the fact that user_stack_pointer() and
current_user_stack_pointer() don't return the same register:
ulong user_stack_pointer(struct pt_regs *regs) { return regs->ar_bspstore; }
#define current_user_stack_pointer() (current_pt_regs()->r12)
The change gets both back in sync.
I think ptrace(PTRACE_GET_SYSCALL_INFO) is the only affected user by
this bug on ia64.
The change fixes 'rt_sigreturn.gen.test' strace test where it was
observed initially.
Link: https://bugs.gentoo.org/769614 [1]
Link: https://lkml.kernel.org/r/20210331084447.2561532-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f0ed93fb9 upstream.
That (and traversals in case of umount .) should be done before
complete_walk(). Either a braino or mismerge damage on queue
reorders - either way, I should've spotted that much earlier.
Fucked-up-by: Al Viro <viro@zeniv.linux.org.uk>
X-Paperbag: Brown
Fixes: 161aff1d93 "LOOKUP_MOUNTPOINT: fold path_mountpointat() into path_lookupat()"
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa26d0c778 upstream.
Commit 8cdddd182b ("ACPI: processor: Fix CPU0 wakeup in
acpi_idle_play_dead()") tried to fix CPU0 hotplug breakage by copying
wakeup_cpu0() + start_cpu0() logic from hlt_play_dead()//mwait_play_dead()
into acpi_idle_play_dead(). The problem is that these functions are not
exported to modules so when CONFIG_ACPI_PROCESSOR=m build fails.
The issue could've been fixed by exporting both wakeup_cpu0()/start_cpu0()
(the later from assembly) but it seems putting the whole pattern into a
new function and exporting it instead is better.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 8cdddd182b ("CPI: processor: Fix CPU0 wakeup in acpi_idle_play_dead()")
Cc: <stable@vger.kernel.org> # 5.10+
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5923249b upstream.
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e9005be87 upstream.
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e6fdeb28f upstream.
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 864db232dc upstream.
nlh is being checked for validtity two times when it is dereferenced in
this function. Check for validity again when updating the flags through
nlh pointer to make the dereferencing safe.
CC: <stable@vger.kernel.org>
Addresses-Coverity: ("NULL pointer dereference")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ad6e9cb39 upstream.
Since commit 1b8b31a2e6 ("selinux: convert policy read-write lock to
RCU"), there is a small window during policy load where the new policy
pointer has already been installed, but some threads may still be
holding the old policy pointer in their read-side RCU critical sections.
This means that there may be conflicting attempts to add a new SID entry
to both tables via sidtab_context_to_sid().
See also (and the rest of the thread):
https://lore.kernel.org/selinux/CAFqZXNvfux46_f8gnvVvRYMKoes24nwm2n3sPbMjrB8vKTW00g@mail.gmail.com/
Fix this by installing the new policy pointer under the old sidtab's
spinlock along with marking the old sidtab as "frozen". Then, if an
attempt to add new entry to a "frozen" sidtab is detected, make
sidtab_context_to_sid() return -ESTALE to indicate that a new policy
has been installed and that the caller will have to abort the policy
transaction and try again after re-taking the policy pointer (which is
guaranteed to be a newer policy). This requires adding a retry-on-ESTALE
logic to all callers of sidtab_context_to_sid(), but fortunately these
are easy to determine and aren't that many.
This seems to be the simplest solution for this problem, even if it
looks somewhat ugly. Note that other places in the kernel (e.g.
do_mknodat() in fs/namei.c) use similar stale-retry patterns, so I think
it's reasonable.
Cc: stable@vger.kernel.org
Fixes: 1b8b31a2e6 ("selinux: convert policy read-write lock to RCU")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f5f0ea5b upstream.
Currently, duplicate_policydb_cond_list() first copies the whole
conditional avtab and then tries to link to the correct entries in
cond_dup_av_list() using avtab_search(). However, since the conditional
avtab may contain multiple entries with the same key, this approach
often fails to find the right entry, potentially leading to wrong rules
being activated/deactivated when booleans are changed.
To fix this, instead start with an empty conditional avtab and add the
individual entries one-by-one while building the new av_lists. This
approach leads to the correct result, since each entry is present in the
av_lists exactly once.
The issue can be reproduced with Fedora policy as follows:
# sesearch -s ftpd_t -t public_content_rw_t -c dir -p create -A
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t public_content_rw_t:dir { add_name create link remove_name rename reparent rmdir setattr unlink watch watch_reads write }; [ ftpd_anon_write ]:True
# setsebool ftpd_anon_write=off ftpd_connect_all_unreserved=off ftpd_connect_db=off ftpd_full_access=off
On fixed kernels, the sesearch output is the same after the setsebool
command:
# sesearch -s ftpd_t -t public_content_rw_t -c dir -p create -A
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t public_content_rw_t:dir { add_name create link remove_name rename reparent rmdir setattr unlink watch watch_reads write }; [ ftpd_anon_write ]:True
While on the broken kernels, it will be different:
# sesearch -s ftpd_t -t public_content_rw_t -c dir -p create -A
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
allow ftpd_t non_security_file_type:dir { add_name create getattr ioctl link lock open read remove_name rename reparent rmdir search setattr unlink watch watch_reads write }; [ ftpd_full_access ]:True
While there, also simplify the computation of nslots. This changes the
nslots values for nrules 2 or 3 to just two slots instead of 4, which
makes the sequence more consistent.
Cc: stable@vger.kernel.org
Fixes: c7c556f1e8 ("selinux: refactor changing booleans")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 442dc00f82 upstream.
1. Make sure all fileds are initialized in avtab_init().
2. Slightly refactor avtab_alloc() to use the above fact.
3. Use h->nslot == 0 as a sentinel in the access functions to prevent
dereferencing h->htable when it's not allocated.
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5db93e7f upstream.
When sock_wait_state() returns -EINPROGRESS, "sk->sk_state" is
LLCP_CONNECTING. In this case, llcp_sock_connect() is repeatedly invoked,
nfc_llcp_sock_link() will add sk to local->connecting_sockets twice.
sk->sk_node->next will point to itself, that will make an endless loop
and hang-up the system.
To fix it, check whether sk->sk_state is LLCP_CONNECTING in
llcp_sock_connect() to avoid repeated invoking.
Fixes: b4011239a0 ("NFC: llcp: Fix non blocking sockets connections")
Reported-by: "kiyin(尹亮)" <kiyin@tencent.com>
Link: https://www.openwall.com/lists/oss-security/2020/11/01/1
Cc: <stable@vger.kernel.org> #v3.11
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 334ef6ed06 upstream.
While allmodconfig and allyesconfig build for s390 there are also
various bots running compile tests with randconfig, where PCI is
disabled. This reveals that a lot of drivers should actually depend on
HAS_IOMEM.
Adding this to each device driver would be a never ending story,
therefore just disable COMPILE_TEST for s390.
The reasoning is more or less the same as described in
commit bc083a64b6 ("init/Kconfig: make COMPILE_TEST depend on !UML").
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26f55a59dc upstream.
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4d4d45643 upstream.
The branch displacement logic in the BPF JIT compilers for x86 assumes
that, for any generated branch instruction, the distance cannot
increase between optimization passes.
But this assumption can be violated due to how the distances are
computed. Specifically, whenever a backward branch is processed in
do_jit(), the distance is computed by subtracting the positions in the
machine code from different optimization passes. This is because part
of addrs[] is already updated for the current optimization pass, before
the branch instruction is visited.
And so the optimizer can expand blocks of machine code in some cases.
This can confuse the optimizer logic, where it assumes that a fixed
point has been reached for all machine code blocks once the total
program size stops changing. And then the JIT compiler can output
abnormal machine code containing incorrect branch displacements.
To mitigate this issue, we assert that a fixed point is reached while
populating the output image. This rejects any problematic programs.
The issue affects both x86-32 and x86-64. We mitigate separately to
ease backporting.
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Reviewed-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e1aa629f1 ]
Nathan reported issue with cleaning empty build directory:
$ make -s O=build distclean
../../scripts/Makefile.include:4: *** \
O=/ho...build/tools/bpf/resolve_btfids does not exist. Stop.
The problem that tools scripts require existing output
directory, otherwise it fails.
Adding check around the resolve_btfids clean target to
ensure the output directory is in place.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/bpf/20210211124004.1144344-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7962cb9b64 ]
We want this clean to be called from tree's root Makefile,
which defines same srctree variable and that will screw
the make setup.
We actually do not use srctree being passed from outside,
so we can solve this by setting current srctree value
directly.
Also changing the way how srctree is initialized as suggested
by Andrri.
Also root Makefile does not define the implicit RM variable,
so adding RM initialization.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210205124020.683286-4-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 219481a8f9 ]
Make SMB2 not print out an error when an oplock break is received for an
unknown handle, similar to SMB1. The debug message which is printed for
these unknown handles may also be misleading, so fix that too.
The SMB2 lease break path is not affected by this patch.
Without this, a program which writes to a file from one thread, and
opens, reads, and writes the same file from another thread triggers the
below errors several times a minute when run against a Samba server
configured with "smb2 leases = no".
CIFS: VFS: \\192.168.0.1 No task to wake, unknown frame received! NumMids 2
00000000: 424d53fe 00000040 00000000 00000012 .SMB@...........
00000010: 00000001 00000000 ffffffff ffffffff ................
00000020: 00000000 00000000 00000000 00000000 ................
00000030: 00000000 00000000 00000000 00000000 ................
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Tom Talpey <tom@talpey.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cee8f4f6fc ]
RHBZ: 1933527
Under SMB1 + POSIX, if an inode is reused on a server after we have read and
cached a part of a file, when we then open the new file with the
re-cycled inode there is a chance that we may serve the old data out of cache
to the application.
This only happens for SMB1 (deprecated) and when posix are used.
The simplest solution to avoid this race is to force a revalidate
on smb1-posix open.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2a419cf49 ]
The sleep warning happens at early boot right at secondary CPU
activation bootup:
smp: Bringing up secondary CPUs ...
BUG: sleeping function called from invalid context at mm/page_alloc.c:4942
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.12.0-rc2-00007-g79e228d0b611-dirty #99
..
Call Trace:
show_stack+0x90/0xc0
dump_stack+0x150/0x1c0
___might_sleep+0x1c0/0x2a0
__might_sleep+0xa0/0x160
__alloc_pages_nodemask+0x1a0/0x600
alloc_page_interleave+0x30/0x1c0
alloc_pages_current+0x2c0/0x340
__get_free_pages+0x30/0xa0
ia64_mca_cpu_init+0x2d0/0x3a0
cpu_init+0x8b0/0x1440
start_secondary+0x60/0x700
start_ap+0x750/0x780
Fixed BSP b0 value from CPU 1
As I understand interrupts are not enabled yet and system has a lot of
memory. There is little chance to sleep and switch to GFP_ATOMIC should
be a no-op.
Link: https://lkml.kernel.org/r/20210315085045.204414-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
