This pull request contains Broadcom ARM-based SoCs Device Tree changes
for v5.8, please pull the following:
- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
controlling power to the SD card, adds support for the vmmc regulator
for the emmc2 controller and finally updates the power management
provider for V3D to use the firmware to solve instabilities.
* tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Use firmware PM driver for V3D
ARM: dts: bcm2711: Add vmmc regulator in emmc2
ARM: dts: bcm2711: Update expgpio's GPIO labels
Link: https://lore.kernel.org/r/20200511210522.28243-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM64: DT: Hisilicon SoCs DT updates for 5.8
- Add pinconf for spi2 and spi3 nodes and increase the drive
strength to achieve the max speed for the Hikey960 board
- Add CTI nodes for the Hikey620 board
* tag 'hisi-arm64-dt-for-5.8' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: Add CTI options
arm64: dts: hikey960: pinctrl: Fix spi2/spi3 pinconf
Link: https://lore.kernel.org/r/5EBE430E.6090508@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Daniel reports that the .cfi_startproc is misplaced for the sigreturn
trampoline, which causes LLVM's unwinder to misbehave:
| I run into this with LLVM’s unwinder.
| This combination was always broken.
This prompted Dave to question our use of CFI directives more generally,
and I ended up going down a rabbit hole trying to figure out how this
very poorly documented stuff gets used.
Move the CFI directives so that the "mysterious NOP" is included in
the .cfi_{start,end}proc block and add a bunch of comments so that I
can save myself another headache in future.
Cc: Tamas Zsoldos <tamas.zsoldos@arm.com>
Reported-by: Dave Martin <dave.martin@arm.com>
Reported-by: Daniel Kiss <daniel.kiss@arm.com>
Tested-by: Daniel Kiss <daniel.kiss@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
For better or worse, GDB relies on the exact instruction sequence in the
VDSO sigreturn trampoline in order to unwind from signals correctly.
Commit c91db232da ("arm64: vdso: Convert to modern assembler annotations")
unfortunately added a BTI C instruction to the start of __kernel_rt_sigreturn,
which breaks this check. Thankfully, it's also not required, since the
trampoline is called from a RET instruction when returning from the signal
handler
Remove the unnecessary BTI C instruction from __kernel_rt_sigreturn,
and do the same for the 32-bit VDSO as well for good measure.
Cc: Daniel Kiss <daniel.kiss@arm.com>
Cc: Tamas Zsoldos <tamas.zsoldos@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Fixes: c91db232da ("arm64: vdso: Convert to modern assembler annotations")
Signed-off-by: Will Deacon <will@kernel.org>
DTS changes for omaps for v5.8 merge window
We add support for beaglebone-ai board that's am5729 based devices.
Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.
Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.
Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.
* tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP5: Make L4SEC clock domain SWSUP only
ARM: OMAP4: Make L4SEC clock domain SWSUP only
ARM: dts: omap5: add DES crypto accelerator node
ARM: dts: omap5: add SHA crypto accelerator node
ARM: dts: omap5: add aes2 entry
ARM: dts: omap5: add aes1 entry
ARM: dts: dra7-ipu-dsp-common: Add watchdog timers to IPU and DSP nodes
ARM: dts: am571x-idk: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: am572x-idk-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: beagle-x15-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra76-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra71-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm-revc: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra7-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra7-ipu-dsp-common: Add timers to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Add mailboxes to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files
ARM: dts: DRA72x: Add aliases for rproc nodes
ARM: dts: DRA74x: Add aliases for rproc nodes
...
Link: https://lore.kernel.org/r/pull-1588873628-477615@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Versatile DTS updates for the v5.8 kernel:
Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.
If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.
* tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Add devicetree for Integrator/AP with IM-PD1
Link: https://lore.kernel.org/r/CACRpkdZ-28o+pPdP7i_fc+7g4ndPWf+SWTsjnhFEegTggiXVSg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Indeed according to the MIPS32 Privileged Resource Architecgture the MAAR
pair register address field either takes [12:31] bits for non-XPA systems
and [12:55] otherwise. In any case the current address mask is just
wrong for 64-bit and 32-bits XPA chips. So lets extend it to 59-bits
of physical address value. This shall cover the 64-bits architecture and
systems with XPA enabled, and won't cause any problem for non-XPA 32-bit
systems, since address values exceeding the architecture specific MAAR
mask will be just truncated with setting zeros in the unsupported upper
bits.
Co-developed-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After commit f5ff0a2802 ("[MIPS] Use generic NTP code for all MIPS
platforms"), TICK_SIZE is not used in ip27-timer.c for many years,
remove it.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The 'pinctrl-names' property should contain a list of names
to the assigned states. The value 'led_pins' in the gpio-leds
node on rk3326-odroid-go2 is not a state that is normally used,
so change it the common name 'default'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200519111444.2208-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
arch/riscv/mm/init.c: In function ‘print_vm_layout’:
arch/riscv/mm/init.c:68:37: error: ‘FIXADDR_START’ undeclared (first use in this function);
arch/riscv/mm/init.c:69:20: error: ‘FIXADDR_TOP’ undeclared
arch/riscv/mm/init.c:70:37: error: ‘PCI_IO_START’ undeclared
arch/riscv/mm/init.c:71:20: error: ‘PCI_IO_END’ undeclared
arch/riscv/mm/init.c:72:38: error: ‘VMEMMAP_START’ undeclared
arch/riscv/mm/init.c:73:20: error: ‘VMEMMAP_END’ undeclared (first use in this function);
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Implement cache_get_priv_group() that will make use of a generic ops
structure to return a private attribute group for custom cache info.
Using riscv_set_cacheinfo_ops() users can hook their own custom function
to return the private attribute group for cacheinfo. In future we can
add more ops to this generic ops structure for SOC specific cacheinfo.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400
reference board with an S922X chip.
- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- Analogue audio output
- 1x RS232 port
- 2x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot
- 1x Power on/off button
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200520014329.12469-6-christianshewitt@gmail.com
Pull UML fixes from Richard Weinberger:
- Two missing includes which caused build issues on recent systems
- Correctly set TRANS_GRE_LEN in our vector network driver
* tag 'for-linus-5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Fix typo in vector driver transport option definition
um: syscall.c: include <asm/unistd.h>
um: Fix xor.h include
It needs access_process_vm() if the traced process does not share
mm with the caller. Solution is similar to what sparc64 does.
Note that genregs32_set() is only ever called with pos being 0
or 32 * sizeof(u32) (the latter - as part of PTRACE_SETREGS
handling).
Cc: stable@kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Move the soc device register code to drivers/soc/imx to align with
i.MX8.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The soc device register code will be moved to drivers/soc/imx/,
the code needs the cpu type definitions. So let's move the cpu
type definitions to a header.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is preparation to move imx_soc_device_init to drivers/soc/imx/
There is no reason to must put dt devices under /sys/devices/soc0,
they could also be under /sys/devices/platform, so we could
pass NULL as parent when calling of_platform_default_populate.
Following soc-imx8.c soc-imx-scu.c using device_initcall, need
to change return type to int type for imx_soc_device_init.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Keep the switch port labels consistent across the different board
variants. If the user wants to rename them, it should be done in
user-space.
Fixes: ab43f03074 ("arm64: dts: ls1028a: sl28: add support for variant 2")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to alloc sub-arches to alloc KASAN regions using optimised
methods (Huge pages on 8xx, BATs on BOOK3S, ...), declare
kasan_init_region() weak.
Also make kasan_init_shadow_page_tables() accessible from outside,
so that it can be called from the specific kasan_init_region()
functions if needed.
And populate remaining KASAN address space only once performed
the region mapping, to allow 8xx to allocate hugepd instead of
standard page tables for mapping via 8M hugepages.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/3c1ce419fa1b5a4171b92d7fb16455ca17e1b96d.1589866984.git.christophe.leroy@csgroup.eu
Commit 45ff3c5595 ("powerpc/kasan: Fix parallel loading of
modules.") added spinlocks to manage parallele module loading.
Since then commit 47febbeeec ("powerpc/32: Force KASAN_VMALLOC for
modules") converted the module loading to KASAN_VMALLOC.
The spinlocking has then become unneeded and can be removed to
simplify kasan_init_shadow_page_tables()
Also remove inclusion of linux/moduleloader.h and linux/vmalloc.h
which are not needed anymore since the removal of modules management.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/81a4d3aee8b82bc1355595935c8f4ad9d3b22a83.1589866984.git.christophe.leroy@csgroup.eu
At the time being, KASAN_SHADOW_END is 0x100000000, which
is 0 in 32 bits representation.
This leads to a couple of issues:
- kasan_remap_early_shadow_ro() does nothing because the comparison
k_cur < k_end is always false.
- In ptdump, address comparison for markers display fails and the
marker's name is printed at the start of the KASAN area instead of
being printed at the end.
However, there is no need to shadow the KASAN shadow area itself,
so the KASAN shadow area can stop shadowing memory at the start
of itself.
With a PAGE_OFFSET set to 0xc0000000, KASAN shadow area is then going
from 0xf8000000 to 0xff000000.
Fixes: cbd18991e2 ("powerpc/mm: Fix an Oops in kasan_mmu_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ae1a3c0d19a37410c209c3fc453634cfcc0ee318.1589866984.git.christophe.leroy@csgroup.eu
This option increases the number of SLB misses by limiting the number
of kernel SLB entries, and increased flushing of cached lookaside
information. This helps stress test difficult to hit paths in the
kernel.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Relocate the code into arch/powerpc/mm, s/torture/stress/]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200511125825.3081305-1-mpe@ellerman.id.au
Booting a power9 server with hash MMU could trigger an undefined
behaviour because pud_offset(p4d, 0) will do,
0 >> (PAGE_SHIFT:16 + PTE_INDEX_SIZE:8 + H_PMD_INDEX_SIZE:10)
Fix it by converting pud_index() and friends to static inline
functions.
UBSAN: shift-out-of-bounds in arch/powerpc/mm/ptdump/ptdump.c:282:15
shift exponent 34 is too large for 32-bit type 'int'
CPU: 6 PID: 1 Comm: swapper/0 Not tainted 5.6.0-rc4-next-20200303+ #13
Call Trace:
dump_stack+0xf4/0x164 (unreliable)
ubsan_epilogue+0x18/0x78
__ubsan_handle_shift_out_of_bounds+0x160/0x21c
walk_pagetables+0x2cc/0x700
walk_pud at arch/powerpc/mm/ptdump/ptdump.c:282
(inlined by) walk_pagetables at arch/powerpc/mm/ptdump/ptdump.c:311
ptdump_check_wx+0x8c/0xf0
mark_rodata_ro+0x48/0x80
kernel_init+0x74/0x194
ret_from_kernel_thread+0x5c/0x74
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20200306044852.3236-1-cai@lca.pw
Christian reports:
MODPOST vmlinux.o
WARNING: modpost: vmlinux.o(.text.unlikely+0x1a0): Section mismatch in
reference from the function .early_init_mmu() to the function
.init.text:.radix__early_init_mmu()
The function .early_init_mmu() references
the function __init .radix__early_init_mmu().
This is often because .early_init_mmu lacks a __init
annotation or the annotation of .radix__early_init_mmu is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1ac): Section mismatch in
reference from the function .early_init_mmu() to the function
.init.text:.hash__early_init_mmu()
The function .early_init_mmu() references
the function __init .hash__early_init_mmu().
This is often because .early_init_mmu lacks a __init
annotation or the annotation of .hash__early_init_mmu is wrong.
The compiler is uninlining early_init_mmu and not putting it in an init
section because there is no annotation. Add it.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Link: https://lore.kernel.org/r/20200429070247.1678172-1-npiggin@gmail.com
With a 64K page size flush with start and end:
(start, end) = (721f680d0000, 721f680e0000)
results in:
(hstart, hend) = (721f68200000, 721f68000000)
ie. hstart is above hend, which indicates no huge page flush is
needed.
However the current logic incorrectly sets hflush = true in this case,
because hstart != hend.
That causes us to call __tlbie_va_range() passing hstart/hend, to do a
huge page flush even though we don't need to. __tlbie_va_range() will
skip the actual tlbie operation for start > end. But it will still end
up calling fixup_tlbie_va_range() and doing the TLB fixups in there,
which is harmless but unnecessary work.
Reported-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop else case, hflush is already false, flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200513030616.152288-1-aneesh.kumar@linux.ibm.com
Merge our topic branch shared with the kvm-ppc tree.
This brings in one commit that touches the XIVE interrupt controller
logic across core and KVM code.
Merge our uaccess-ppc topic branch. It is based on the uaccess topic
branch that we're sharing with Viro.
This includes the addition of user_[read|write]_access_begin(), as
well as some powerpc specific changes to our uaccess routines that
would conflict badly if merged separately.
