The RTC found on the MAX77620 PMIC can be used as a wakeup source on
Jetson TX2, which is useful to wake the system from suspend at a given
time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Enable the VI I2C so that the peripherals connected to it (such as the
camera connector, an INA3221 power monitor and the USB 3.1 4-port hub)
can be accessed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 contains VI controller for video input capture from MIPI
CSI camera sensors and also supports built-in test pattern generator.
CSI ports can be one-to-one mapped to VI channels for capturing from
an external sensor or from built-in test pattern generator.
This patch adds support for VI and CSI and enables them in Tegra210
device tree.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 device tree is missing reset-cells property for the memory
controller node. This patch adds it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 device tree lists CSI clock and reset under SOR powergate
node.
But Tegra210 has CSICIL in SOR partition and CSI in VENC partition.
So, this patch includes fix for SOR powergate node.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The PMIC RTC is currently unable to wakeup Tegra194 on the Jetson Xavier
platform because the interrupt from the PMIC is not usin the PMC as the
interrupt parent but the GIC directly. Update the PMIC interrupt to use
the PMC as the interrupt parent so that the PMIC RTC alarms can wakeup
the device.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 'phy-mode' property is currently defined as 'rgmii' for Jetson
Xavier. This indicates that the RGMII RX and TX delays are set by the
MAC and the internal delays set by the PHY are not used.
If the Marvell PHY driver is enabled, such that it is used and not the
generic PHY, ethernet failures are seen (DHCP is failing to obtain an
IP address) and this is caused because the Marvell PHY driver is
disabling the internal RX and TX delays. For Jetson Xavier the internal
PHY RX and TX delay should be used and so fix this by setting the
'phy-mode' to 'rgmii-id' and not 'rgmii'.
Fixes: f89b58ce71 ("arm64: tegra: Add ethernet controller on Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The external memory controller can be used as a cooling device for the
LPDDR chips. Hook it up to the "mem" thermal zone of the SOCTHERM block
so that temperature polling can be enabled on the EMC when a given
temperature is exceeded.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Quoth the man page:
```
If the tracee was restarted by PTRACE_SYSCALL or PTRACE_SYSEMU, the
tracee enters syscall-enter-stop just prior to entering any system
call (which will not be executed if the restart was using
PTRACE_SYSEMU, regardless of any change made to registers at this
point or how the tracee is restarted after this stop).
```
The parenthetical comment is currently true on x86 and powerpc,
but not currently true on arm64. arm64 re-checks the _TIF_SYSCALL_EMU
flag after the syscall entry ptrace stop. However, at this point,
it reflects which method was used to re-start the syscall
at the entry stop, rather than the method that was used to reach it.
Fix that by recording the original flag before performing the ptrace
stop, bringing the behavior in line with documentation and x86/powerpc.
Fixes: f086f67485 ("arm64: ptrace: add support for syscall emulation")
Cc: <stable@vger.kernel.org> # 5.3.x-
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Will Deacon <will@kernel.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Bin Lu <Bin.Lu@arm.com>
[catalin.marinas@arm.com: moved 'flags' bit masking]
[catalin.marinas@arm.com: changed 'flags' type to unsigned long]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In preparation for adding ARM64 support, split hyperv-tlfs.h into
architecture dependent and architecture independent files, similar
to what has been done with mshyperv.h. Move architecture independent
definitions into include/asm-generic/hyperv-tlfs.h. The split will
avoid duplicating significant lines of code in the ARM64 version of
hyperv-tlfs.h. The split has no functional impact.
Some of the common definitions have "X64" in the symbol name. Change
these to remove the "X64" in the architecture independent version of
hyperv-tlfs.h, but add aliases with the "X64" in the x86 version so
that x86 code will continue to compile. A later patch set will
change all the references and allow removal of the aliases.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20200422195737.10223-4-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
The Hyper-V Reference TSC Page structure is defined twice. struct
ms_hyperv_tsc_page has padding out to a full 4 Kbyte page size. But
the padding is not needed because the declaration includes a union
with HV_HYP_PAGE_SIZE. KVM uses the second definition, which is
struct _HV_REFERENCE_TSC_PAGE, because it does not have the padding.
Fix the duplication by removing the padding from ms_hyperv_tsc_page.
Fix up the KVM code to use it. Remove the no longer used struct
_HV_REFERENCE_TSC_PAGE.
There is no functional change.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20200422195737.10223-2-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Let's use the same signature and parameter names as in the generic
ioremap() definition making the physical address' type explicit.
Add a check against address wrap around as in the generic
lib/ioremap.c:ioremap_prot() code.
Finally use free_vm_area() instead of vunmap() as in the generic code.
Besides being clearer free_vm_area() can also skip a few additional
checks compared with vunmap().
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
s390 documentation now lives in IBM Knowledge Center, so update the link
in the zfcpdump documentation.
Also, remove the old developerWorks links from the appldata source code.
Those were not really documentation related, but rather a reminder to the
developer that some documentation has to be adjusted when changing the
record layout, which should still be pretty obvious from the remaining
comment.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Assume we have a crashkernel area of 256MB reserved:
root@vm0:~# cat /proc/iomem
00000000-6fffffff : System RAM
0f258000-0fcfffff : Kernel code
0fd00000-101d10e3 : Kernel data
105b3000-1068dfff : Kernel bss
70000000-7fffffff : Crash kernel
This exactly corresponds to memory block 7 (memory block size is 256MB).
Trying to offline that memory block results in:
root@vm0:~# echo "offline" > /sys/devices/system/memory/memory7/state
-bash: echo: write error: Device or resource busy
[ 128.458762] page:000003d081c00000 refcount:1 mapcount:0 mapping:00000000d01cecd4 index:0x0
[ 128.458773] flags: 0x1ffff00000001000(reserved)
[ 128.458781] raw: 1ffff00000001000 000003d081c00008 000003d081c00008 0000000000000000
[ 128.458781] raw: 0000000000000000 0000000000000000 ffffffff00000001 0000000000000000
[ 128.458783] page dumped because: unmovable page
The craskernel area is marked reserved in the bootmem allocator. This
results in the memmap getting initialized (refcount=1, PG_reserved), but
the pages are never freed to the page allocator.
So these pages look like allocated pages that are unmovable (esp.
PG_reserved), and therefore, memory offlining fails early, when trying to
isolate the page range.
We only have to care about the exchange area, make that clear.
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Philipp Rudo <prudo@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@kernel.org>
Link: https://lore.kernel.org/r/20200424083904.8587-1-david@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On s390 PCI Virtual Functions (VFs) are scanned by firmware and are made
available to Linux via the hot-plug interface. As such the common code
path of doing the scan directly using the parent Physical Function (PF)
is not used and fenced off with the no_vf_scan attribute.
Even if the partition created the VFs itself e.g. using the sriov_numvfs
attribute of a PF, the PF/VF links thus need to be established after the
fact. To do this when a VF is plugged we scan through all functions on
the same zbus and test whether they are the parent PF in which case we
establish the necessary links.
With these links established there is now no more need to fence off
pci_iov_remove_virtfn() for pdev->no_vf_scan as the common code now
works fine.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506154139.90609-3-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
With certain kernel configurations, the R_390_JMP_SLOT relocation type
might be generated, which is not expected by the KASLR relocation code,
and the kernel stops with the message "Unknown relocation type".
This was found with a zfcpdump kernel config, where CONFIG_MODULES=n
and CONFIG_VFIO=n. In that case, symbol_get() is used on undefined
__weak symbols in virt/kvm/vfio.c, which results in the generation
of R_390_JMP_SLOT relocation types.
Fix this by handling R_390_JMP_SLOT similar to R_390_GLOB_DAT.
Fixes: 805bc0bc23 ("s390/kernel: build a relocatable kernel")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On s390, the layout of normal and large ptes (i.e. pmds/puds) differs.
Therefore, set_huge_pte_at() does a conversion from a normal pte to
the corresponding large pmd/pud. So, when converting an empty pte, this
should result in an empty pmd/pud, which would return true for
pmd/pud_none().
However, after conversion we also mark the pmd/pud as large, and
therefore present. For empty ptes, this will result in an empty pmd/pud
that is also marked as large, and pmd/pud_none() would not return true.
There is currently no issue with this behaviour, as set_huge_pte_at()
does not seem to be called for empty ptes. It would be valid though, so
let's fix this by not marking empty ptes as large in set_huge_pte_at().
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add more arch page table helper
tests").
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add missing include which adds the prototype to plat_time_init().
Fixes: f932449c11 ("MIPS: ingenic: Drop obsolete code, merge the rest in setup.c")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
After commit 0ce5ebd24d ("mfd: ioc3: Add driver for SGI IOC3 chip"),
the related includes and comment about ioc3 are not used any more in
ip27-timer.c, remove them.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Group the port definitions of the dvi-converter in a 'ports' node to
make it compliant with the ti,tfp410 binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "reset-controller" instead of "src" for
i.MX5 SoCs src nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node name should be generic, use "reset-controller" instead of "src" for
i.MX6/i.MX7 SoCs src nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing input mux for ENET2 mdio. Without this setting, it is not
possible to read the MDIO answers back from the PHY.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although ocotp clock is always ON for i.MX6SL, OCOTP can be
accessed directly, but since i.MX6SL nvmem interface is supported,
and fsl,tempmon-data is deprecated, use it instead of getting fuse
data by reading ocotp directly, this makes all i.MX6 SoCs aligned.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although ocotp clock is always ON for i.MX6QDL, OCOTP can be
accessed directly, but since i.MX6QDL nvmem interface is supported,
and fsl,tempmon-data is deprecated, use it instead of getting fuse
data by reading ocotp directly, this makes all i.MX6 SoCs aligned.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the wl_reg regulator to usdhc2 such that it can be enabled
and disabled as needed. There is no need for this to be always-on.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Sterling-LWB has a BCM4330 which has a UART based bluetooth
HCI. Add support for binding to the bcm_hci driver to take care
of handling the shutdown gpio and loading firmware.
Because the shutdown gpio is more of an enable than a regulator
go ahead and replace the regulator with a shutdown-gpio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix sparse warning:
arch/arm/mach-imx/mach-pcm037.c:407:30: warning: symbol
'pcm970_sja1000_platform_data' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ma Feng <mafeng.ma@huawei.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are new drivers for functionality of that family
(RTC and ADC), so enable them, since they are used by
various i.MX6 boards.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign IMX8M*_CLK_A53_SRC's parent to system pll1 and
assign IMX8M*_CLK_A53_CORE's parent to arm pll out as what
is done in drivers/clk/imx/clk-imx8m*.c, then we could remove
the settings in driver which triggers lockdep warning.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that the LPUART has support for the LS1028A SoC, also enable it on
our board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The iomuxc-gpr node is not used and causes the following dtc
warning with W=1:
arch/arm/boot/dts/imx50.dtsi:286.28-289.6: Warning (unique_unit_address): /soc/bus@50000000/iomuxc@53fa8000: duplicate unit-address (also used in node /soc/bus@50000000/iomuxc-gpr@53fa8000)
Remove the node to fix the warning.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
