[ Upstream commit a7196048cd ]
The PLLU (USB) consists of the PLL configuration itself and configuration
of the PLLU outputs. The PLLU programming is inconsistent on T30 vs T114,
where T114 immediately bails out if PLLU is enabled and T30 re-enables
a potentially already enabled PLL (left after bootloader) and then fully
reprograms it, which could be unsafe to do. The correct way should be to
skip enabling of the PLL if it's already enabled and then apply
configuration to the outputs. This patch doesn't fix any known problems,
it's a minor improvement.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c592c8a28f ]
The refcounting of the gate clocks has a bug causing the enable_refcnt
to underflow when unused clocks are disabled. This happens because clk
provider erroneously bumps the refcount if clock is enabled at a boot
time, which it shouldn't be doing, and it does this only for the gate
clocks, while peripheral clocks are using the same gate ops and the
peripheral clocks are missing the initial bump. Hence the refcount of
the peripheral clocks is 0 when unused clocks are disabled and then the
counter is decremented further by the gate ops, causing the integer
underflow.
Fix this problem by removing the erroneous bump and by implementing the
disable_unused() callback, which disables the unused gates properly.
The visible effect of the bug is such that the unused clocks are never
gated if a loaded kernel module grabs the unused clocks and starts to use
them. In practice this shouldn't cause any real problems for the drivers
and boards supported by the kernel today.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4751d2aa32 ]
stmmac_mdio_register() has logic to search for PHYs on the MDIO bus and
assign them IRQ lines, as well as to set priv->plat->phy_addr.
If no PHY is found, the "found" variable remains set to 0 and the
function errors out.
After the introduction of commit f213bbe8a9 ("net: stmmac: Integrate
it with DesignWare XPCS"), the "found" variable was immediately reused
for searching for a PCS on the same MDIO bus.
This can result in 2 types of potential problems (none of them seems to
be seen on the only Intel system that sets has_xpcs = true, otherwise it
would have been reported):
1. If a PCS is found but a PHY is not, then the code happily exits with
no error. One might say "yes, but this is not possible, because
of_mdiobus_register will probe a PHY for all MDIO addresses,
including for the XPCS, so if an XPCS exists, then a PHY certainly
exists too". Well, that is not true, see intel_mgbe_common_data():
/* Ensure mdio bus scan skips intel serdes and pcs-xpcs */
plat->mdio_bus_data->phy_mask = 1 << INTEL_MGBE_ADHOC_ADDR;
plat->mdio_bus_data->phy_mask |= 1 << INTEL_MGBE_XPCS_ADDR;
2. A PHY is found but an MDIO device with the XPCS PHY ID isn't, and in
that case, the error message will be "No PHY found". Confusing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210527155959.3270478-1-olteanv@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8613641063 ]
Fix the logic so that if both ports netdevices are enabled or disabled,
use the trivial mapping without swapping.
If only one of the netdevice's tx is enabled, use it to remap traffic to
that port.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c07274ab1a ]
rep_tc copy REG_C1 to REG_B. IPsec crypto utilizes the whole REG_B
register with BIT31 as IPsec marker. rep_tc_update_skb drops
IPsec because it thought REG_B contains bad value.
In previous patch, BIT 31 of REG_C1 is reserved for IPsec.
Skip the rep_tc_update_skb if BIT31 of REG_B is set.
Signed-off-by: Huy Nguyen <huyn@nvidia.com>
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b514958dd1 ]
The igb driver was trying hard to be sparse correct, but somehow
ended up converting a variable into little endian order and then
tries to OR something with it.
A much plainer way of doing things is to leave all variables and
OR operations in CPU (non-endian) mode, and then convert to
little endian only once, which is what this change does.
This probably fixes a bug that might have been seen only on
big endian systems.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7cbfb028b ]
The sparse build (C=2) finds some issues with how the driver
dealt with the (very difficult) hardware that in some generations
uses little-endian, and in others uses big endian, for the VLAN
field. The code as written picks __le16 as a type and for some
hardware revisions we override it to __be16 as done in this
patch. This impacted the VF driver as well so fix it there too.
Also change the vlan_tci assignment to override the sparse
warning without changing functionality.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Dave Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4ef55288a ]
Sparse tool was warning on some implicit conversions from
little endian data read from the EEPROM on the e100 cards.
Fix these by being explicit about the conversions using
le16_to_cpu().
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa236c2b2d ]
In function udf_symlink, epos.bh is assigned with the value returned
by udf_tgetblk. The function udf_tgetblk is defined in udf/misc.c
and returns the value of sb_getblk function that could be NULL.
Then, epos.bh is used without any check, causing a possible
NULL pointer dereference when sb_getblk fails.
This fix adds a check to validate the value of epos.bh.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=213083
Signed-off-by: Arturo Giusti <koredump@protonmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c61cdbdbff ]
Problem: If scheduler is already stopped by the time sched_entity
is released and entity's job_queue not empty I encountred
a hang in drm_sched_entity_flush. This is because drm_sched_entity_is_idle
never becomes false.
Fix: In drm_sched_fini detach all sched_entities from the
scheduler's run queues. This will satisfy drm_sched_entity_is_idle.
Also wakeup all those processes stuck in sched_entity flushing
as the scheduler main thread which wakes them up is stopped by now.
v2:
Reverse order of drm_sched_rq_remove_entity and marking
s_entity as stopped to prevent reinserion back to rq due
to race.
v3:
Drop drm_sched_rq_remove_entity, only modify entity->stopped
and check for it in drm_sched_entity_is_idle
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512142648.666476-14-andrey.grodzovsky@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ff8435e5 ]
modern userspace applications, like OVN, can configure the TC datapath to
"recirculate" packets several times. If more than 4 "recirculation" rules
are configured, packets can be dropped by __tcf_classify().
Changing the maximum number of reclassifications (from 4 to 16) should be
sufficient to prevent drops in most use cases, and guard against loops at
the same time.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86544c3de6 ]
Similar to the way in which of_mdiobus_register() has a fallback to the
non-DT based mdiobus_register() when CONFIG_OF is not set, we can create
a shim for the device-managed devm_of_mdiobus_register() which calls
devm_mdiobus_register() and discards the struct device_node *.
In particular, this solves a build issue with the qca8k DSA driver which
uses devm_of_mdiobus_register and can be compiled without CONFIG_OF.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b097bea102 ]
mdio drivers should not use REGCHACHE. Also disable locking since it's
handled by the mdio users and regmap is always accessed atomically.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69777e6ca3 ]
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8380c81d5c ]
__napi_schedule_irqoff() is an optimized version of __napi_schedule()
which can be used where it is known that interrupts are disabled,
e.g. in interrupt-handlers, spin_lock_irq() sections or hrtimer
callbacks.
On PREEMPT_RT enabled kernels this assumptions is not true. Force-
threaded interrupt handlers and spinlocks are not disabling interrupts
and the NAPI hrtimer callback is forced into softirq context which runs
with interrupts enabled as well.
Chasing all usage sites of __napi_schedule_irqoff() is a whack-a-mole
game so make __napi_schedule_irqoff() invoke __napi_schedule() for
PREEMPT_RT kernels.
The callers of ____napi_schedule() in the networking core have been
audited and are correct on PREEMPT_RT kernels as well.
Reported-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34e7434ba4 ]
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 009fc857c5 ]
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c72e6ab66 ]
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33ae8f801a ]
If multiple threads are accessing the same huge page at the same
time, hugetlb_cow will be called if one thread write the COW huge
page. And function huge_ptep_clear_flush is called to notify other
threads to clear the huge pte tlb entry. The other threads clear
the huge pte tlb entry and reload it from page table, the reload
huge pte entry may be old.
This patch fixes this issue on mips platform, and it clears huge
pte entry before notifying other threads to flush current huge
page entry, it is similar with other architectures.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 443ef39b49 ]
Sparse is not happy about handling of strict types in pch_ptp_match():
.../pch_gbe_main.c:158:33: warning: incorrect type in argument 2 (different base types)
.../pch_gbe_main.c:158:33: expected unsigned short [usertype] uid_hi
.../pch_gbe_main.c:158:33: got restricted __be16 [usertype]
.../pch_gbe_main.c:158:45: warning: incorrect type in argument 3 (different base types)
.../pch_gbe_main.c:158:45: expected unsigned int [usertype] uid_lo
.../pch_gbe_main.c:158:45: got restricted __be32 [usertype]
.../pch_gbe_main.c:158:56: warning: incorrect type in argument 4 (different base types)
.../pch_gbe_main.c:158:56: expected unsigned short [usertype] seqid
.../pch_gbe_main.c:158:56: got restricted __be16 [usertype]
Fix that by switching to use proper accessors to BE data.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ea3dbc4e ]
Disable all ip's hw status to false before any hw_init.
Only set it to true until its hw_init is executed.
The old 5.9 branch has this change but somehow the 5.11 kernrel does
not have this fix.
Without this change, sriov tdr have gfx IB test fail.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Review-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba4e0339a6 ]
[Bug][DP501]
If ASPEED P2A (PCI to AHB) bridge is disabled and disallowed for
CVE_2019_6260 item3, and then the monitor's EDID is unable read through
Parade DP501.
The reason is the DP501's FW is mapped to BMC addressing space rather
than Host addressing space.
The resolution is that using "pci_iomap_range()" maps to DP501's FW that
stored on the end of FB (Frame Buffer).
In this case, FrameBuffer reserves the last 2MB used for the image of
DP501.
Signed-off-by: KuoHsiang Chou <kuohsiang_chou@aspeedtech.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210421085859.17761-1-kuohsiang_chou@aspeedtech.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2c669ef697 upstream.
Powerpc currently resets a CPU's idle task preempt_count to 0 before
said task starts executing the secondary startup routine (and becomes an
idle task proper).
This conflicts with commit f1a0a376ca ("sched/core: Initialize the
idle task with preemption disabled").
which initializes all of the idle tasks' preempt_count to
PREEMPT_DISABLED during smp_init(). Note that this was superfluous
before said commit, as back then the hotplug machinery would invoke
init_idle() via idle_thread_get(), which would have already reset the
CPU's idle task's preempt_count to PREEMPT_ENABLED.
Get rid of this preempt_count write.
Fixes: f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
Reported-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210707183831.2106509-1-valentin.schneider@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7154cbd31c upstream.
Compiling the recent dma-iommu changes under 32-bit x86 triggers this
compile warning:
drivers/iommu/dma-iommu.c:249:5: warning: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘phys_addr_t’ {aka ‘unsigned int’} [-Wformat=]
The reason is that %llx is used to print a variable of type
phys_addr_t. Fix it by using the correct %pa format specifier for
phys_addr_t.
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Oza Pawandeep <poza@codeaurora.org>
Fixes: 571f316074 ("iommu/dma: Fix IOVA reserve dma ranges")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20210607124905.27525-1-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a942f5780 upstream.
S390's init_idle_preempt_count(p, cpu) doesn't actually let us initialize the
preempt_count of the requested CPU's idle task: it unconditionally writes
to the current CPU's. This clearly conflicts with idle_threads_init(),
which intends to initialize *all* the idle tasks, including their
preempt_count (or their CPU's, if the arch uses a per-CPU preempt_count).
Unfortunately, it seems the way s390 does things doesn't let us initialize
every possible CPU's preempt_count early on, as the pages where this
resides are only allocated when a CPU is brought up and are freed when it
is brought down.
Let the arch-specific code set a CPU's preempt_count when its lowcore is
allocated, and turn init_idle_preempt_count() into an empty stub.
Fixes: f1a0a376ca ("sched/core: Initialize the idle task with preemption disabled")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Link: https://lore.kernel.org/r/20210707163338.1623014-1-valentin.schneider@arm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29dd19e3ac upstream.
The usage of pm_runtime_resume_and_get() removed the need of a
temporary integer. So, drop it.
Fixes: 59f96244af ("media: exynos4-is: fix pm_runtime_get_sync() usage count")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
