commit 93a8ba2a61 upstream.
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552ca27929 upstream.
Move the power domain to its actual user. This keeps the power domain
enabled even when the USB host is runtime suspended. This is necessary
to detect any downstream events, like device attach.
Fixes: 02f8eb40ef ("ARM: dts: imx7s: Add power domain for imx7d HSIC")
Suggested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 993a2adc6e upstream.
dp_catalog_ctrl_reset() will software reset DP controller. But it will
not reset programmable registers to default value. DP driver still have
to clear mask bits to interrupt status registers to disable interrupts
after software reset of controller.
At current implementation, dp_ctrl_reset_irq_ctrl() will software reset dp
controller but did not call dp_catalog_ctrl_enable_irq(false) to clear hpd
related interrupt mask bits to disable hpd related interrupts due to it
mistakenly think hpd related interrupt mask bits will be cleared by software
reset of dp controller automatically. This mistake may cause system to crash
during suspending procedure due to unexpected irq fired and trigger event
thread to access dp controller registers with controller clocks are disabled.
This patch fixes system crash during suspending problem by removing "enable"
flag condition checking at dp_ctrl_reset_irq_ctrl() so that hpd related
interrupt mask bits are cleared to prevent unexpected from happening.
Changes in v2:
-- add more details commit text
Changes in v3:
-- add synchrons_irq()
-- add atomic_t suspended
Changes in v4:
-- correct Fixes's commit ID
-- remove synchrons_irq()
Changes in v5:
-- revise commit text
Changes in v6:
-- add event_lock to protect "suspended"
Changes in v7:
-- delete "suspended" flag
Fixes: 989ebe7bc4 ("drm/msm/dp: do not initialize phy until plugin interrupt received")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/486591/
Link: https://lore.kernel.org/r/1652804494-19650-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3eac42665 upstream.
The platform's RNG must be available before random_init() in order to be
useful for initial seeding, which in turn means that it needs to be
called from setup_arch(), rather than from an init call.
Complicating things, however, is that POWER8 systems need some per-cpu
state and kmalloc, which isn't available at this stage. So we split
things up into an early phase and a later opportunistic phase. This
commit also removes some noisy log messages that don't add much.
Fixes: a4da0d50b2 ("powerpc: Implement arch_get_random_long/int() for powernv")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Add of_node_put(), use pnv naming, minor change log editing]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220621140849.127227-1-Jason@zx2c4.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bc08056a6 upstream.
Add a special case to block_rtas_call() to allow the ibm,platform-dump RTAS
call through the RTAS filter if the buffer address is 0.
According to PAPR, ibm,platform-dump is called with a null buffer address
to notify the platform firmware that processing of a particular dump is
finished.
Without this, on a pseries machine with CONFIG_PPC_RTAS_FILTER enabled, an
application such as rtas_errd that is attempting to retrieve a dump will
encounter an error at the end of the retrieval process.
Fixes: bd59380c5b ("powerpc/rtas: Restrict RTAS requests from userspace")
Cc: stable@vger.kernel.org
Reported-by: Sathvika Vasireddy <sathvika@linux.ibm.com>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220614134952.156010-1-ajd@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20a9689b36 upstream.
The platform's RNG must be available before random_init() in order to be
useful for initial seeding, which in turn means that it needs to be
called from setup_arch(), rather than from an init call. Fortunately,
each platform already has a setup_arch function pointer, which means
it's easy to wire this up. This commit also removes some noisy log
messages that don't add much.
Fixes: c25769fdda ("powerpc/microwatt: Add support for hardware random number generator")
Cc: stable@vger.kernel.org # v5.14+
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220611151015.548325-2-Jason@zx2c4.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9decacd8b3 upstream.
When introducing support for processed channels I needed
to invert the expression:
if (!iio_channel_has_info(schan, IIO_CHAN_INFO_RAW) ||
!iio_channel_has_info(schan, IIO_CHAN_INFO_SCALE))
dev_err(dev, "source channel does not support raw/scale\n");
To the inverse, meaning detect when we can usse raw+scale
rather than when we can not. This was the result:
if (iio_channel_has_info(schan, IIO_CHAN_INFO_RAW) ||
iio_channel_has_info(schan, IIO_CHAN_INFO_SCALE))
dev_info(dev, "using raw+scale source channel\n");
Ooops. Spot the error. Yep old George Boole came up and bit me.
That should be an &&.
The current code "mostly works" because we have not run into
systems supporting only raw but not scale or only scale but not
raw, and I doubt there are few using the rescaler on anything
such, but let's fix the logic.
Cc: Liam Beguin <liambeguin@gmail.com>
Cc: stable@vger.kernel.org
Fixes: 53ebee9499 ("iio: afe: iio-rescale: Support processed channels")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Liam Beguin <liambeguin@gmail.com>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20220524075448.140238-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9354c224c9 upstream.
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: 47196620c8 ("iio: mxc4005: add data ready trigger for mxc4005")
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220524181150.9240-4-ddrokosov@sberdevices.ru
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f3205b04 upstream.
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: 0668a4e4d2 ("iio: accel: bma180: Fix indio_dev->trig assignment")
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220524181150.9240-2-ddrokosov@sberdevices.ru
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed302925d7 upstream.
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: c1288b8338 ("iio: accel: kxcjk-1013: Increment ref counter for indio_dev->trig")
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220524181150.9240-3-ddrokosov@sberdevices.ru
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d710359c0b upstream.
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: f1f065d7ac ("iio: chemical: ccs811: Add support for data ready trigger")
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220524181150.9240-5-ddrokosov@sberdevices.ru
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10b9c2c33a upstream.
IIO trigger interface function iio_trigger_get() should be called after
iio_trigger_register() (or its devm analogue) strictly, because of
iio_trigger_get() acquires module refcnt based on the trigger->owner
pointer, which is initialized inside iio_trigger_register() to
THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs
callback or "delete module" path) will dereference "default" module
refcnt, which is incorrect behaviour.
Fixes: e4a70e3e7d ("iio: humidity: add support to hts221 rh/temp combo device")
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220524181150.9240-6-ddrokosov@sberdevices.ru
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4cde00d507 upstream.
This fixes the below corruption.
[345393.335389] F2FS-fs (vdb): sanity_check_inode: inode (ino=6d0, mode=33206) should not have inline_data, run fsck to fix
Cc: <stable@vger.kernel.org>
Fixes: 677a82b44e ("f2fs: fix to do sanity check for inline inode")
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf7ba8ee75 upstream.
We are hitting the following deadlock in production occasionally
Task 1 Task 2 Task 3 Task 4 Task 5
fsync(A)
start trans
start commit
falloc(A)
lock 5m-10m
start trans
wait for commit
fiemap(A)
lock 0-10m
wait for 5m-10m
(have 0-5m locked)
have btrfs_need_log_full_commit
!full_sync
wait_ordered_extents
finish_ordered_io(A)
lock 0-5m
DEADLOCK
We have an existing dependency of file extent lock -> transaction.
However in fsync if we tried to do the fast logging, but then had to
fall back to committing the transaction, we will be forced to call
btrfs_wait_ordered_range() to make sure all of our extents are updated.
This creates a dependency of transaction -> file extent lock, because
btrfs_finish_ordered_io() will need to take the file extent lock in
order to run the ordered extents.
Fix this by stopping the transaction if we have to do the full commit
and we attempted to do the fast logging. Then attach to the transaction
and commit it if we need to.
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97e86631bc upstream.
In 196d59ab9c "btrfs: switch extent buffer tree lock to rw_semaphore"
the functions for tree read locking were rewritten, and in the process
the read lock functions started setting eb->lock_owner = current->pid.
Previously lock_owner was only set in tree write lock functions.
Read locks are shared, so they don't have exclusive ownership of the
underlying object, so setting lock_owner to any single value for a
read lock makes no sense. It's mostly harmless because write locks
and read locks are mutually exclusive, and none of the existing code
in btrfs (btrfs_init_new_buffer and print_eb_refs_lock) cares what
nonsense is written in lock_owner when no writer is holding the lock.
KCSAN does care, and will complain about the data race incessantly.
Remove the assignments in the read lock functions because they're
useless noise.
Fixes: 196d59ab9c ("btrfs: switch extent buffer tree lock to rw_semaphore")
CC: stable@vger.kernel.org # 5.15+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9faa1c8f92 upstream.
"make dtbs_check":
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080100: phys: [[17, 0], [31]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0100: phys: [[17, 1], [33], [21, 0]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
Some USB EHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs. Increase the maximum number of PHYs to 3, which is sufficient for
now.
Fixes: 0499220d6d ("dt-bindings: Add missing array size constraints")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c5d19e2f9714f43effd90208798fc1936098078f.1655301043.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f074c1c95 upstream.
"make dtbs_check":
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee080000: phys: [[17, 0], [31]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
arch/arm/boot/dts/r8a77470-iwg23s-sbc.dtb: usb@ee0c0000: phys: [[17, 1], [33], [21, 0]] is too long
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
Some USB OHCI controllers (e.g. on the Renesas RZ/G1C SoC) have multiple
PHYs. Increase the maximum number of PHYs to 3, which is sufficient for
now.
Fixes: 0499220d6d ("dt-bindings: Add missing array size constraints")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0112f9c8881513cb33bf7b66bc743dd08b35a2f5.1655301203.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90bc2af246 upstream.
Re-reading a recently merged fix to the raw_gadget driver showed that
it inadvertently introduced a double-free bug in a failure pathway.
If raw_ioctl_init() encounters an error after the driver ID number has
been allocated, it deallocates the ID number before returning. But
when dev_free() runs later on, it will then try to deallocate the ID
number a second time.
Closely related to this issue is another error in the recent fix: The
ID number is stored in the raw_dev structure before the code checks to
see whether the structure has already been initialized, in which case
the new ID number would overwrite the earlier value.
The solution to both bugs is to keep the new ID number in a local
variable, and store it in the raw_dev structure only after the check
for prior initialization. No errors can occur after that point, so
the double-free will never happen.
Fixes: f2d8c26068 ("usb: gadget: Fix non-unique driver names in raw-gadget driver")
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YrMrRw5AyIZghN0v@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2d8c26068 upstream.
In a report for a separate bug (which has already been fixed by commit
5f0b5f4d50 "usb: gadget: fix race when gadget driver register via
ioctl") in the raw-gadget driver, the syzbot console log included
error messages caused by attempted registration of a new driver with
the same name as an existing driver:
> kobject_add_internal failed for raw-gadget with -EEXIST, don't try to register things with the same name in the same directory.
> UDC core: USB Raw Gadget: driver registration failed: -17
> misc raw-gadget: fail, usb_gadget_register_driver returned -17
These errors arise because raw_gadget.c registers a separate UDC
driver for each of the UDC instances it creates, but these drivers all
have the same name: "raw-gadget". Until recently this wasn't a
problem, but when the "gadget" bus was added and UDC drivers were
registered on this bus, it became possible for name conflicts to cause
the registrations to fail. The reason is simply that the bus code in
the driver core uses the driver name as a sysfs directory name (e.g.,
/sys/bus/gadget/drivers/raw-gadget/), and you can't create two
directories with the same pathname.
To fix this problem, the driver names used by raw-gadget are made
distinct by appending a unique ID number: "raw-gadget.N", with a
different value of N for each driver instance. And to avoid the
proliferation of error handling code in the raw_ioctl_init() routine,
the error return paths are refactored into the common pattern (goto
statements leading to cleanup code at the end of the routine).
Link: https://lore.kernel.org/all/0000000000008c664105dffae2eb@google.com/
Fixes: fc274c1e99 "USB: gadget: Add a new bus for gadgets"
CC: Andrey Konovalov <andreyknvl@gmail.com>
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+02b16343704b3af1667e@syzkaller.appspotmail.com
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Acked-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YqdG32w+3h8c1s7z@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83810f84ec upstream.
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be857b7f77 ]
Events CPU_CYCLES and INSTRUCTIONS can be submitted with two different
perf_event attribute::type values:
- PERF_TYPE_HARDWARE: when invoked via perf tool predefined events name
cycles or cpu-cycles or instructions.
- pmu->type: when invoked via perf tool event name cpu_cf/CPU_CYLCES/ or
cpu_cf/INSTRUCTIONS/. This invocation also selects the PMU to which
the event belongs.
Handle both type of invocations identical for events CPU_CYLCES and
INSTRUCTIONS. They address the same hardware.
The result is different when event modifier exclude_kernel is also set.
Invocation with event modifier for user space event counting fails.
Output before:
# perf stat -e cpum_cf/cpu_cycles/u -- true
Performance counter stats for 'true':
<not supported> cpum_cf/cpu_cycles/u
0.000761033 seconds time elapsed
0.000076000 seconds user
0.000725000 seconds sys
#
Output after:
# perf stat -e cpum_cf/cpu_cycles/u -- true
Performance counter stats for 'true':
349,613 cpum_cf/cpu_cycles/u
0.000844143 seconds time elapsed
0.000079000 seconds user
0.000800000 seconds sys
#
Fixes: 6a82e23f45 ("s390/cpumf: Adjust registration of s390 PMU device drivers")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Acked-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
[agordeev@linux.ibm.com corrected commit ID of Fixes commit]
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e648783318 ]
This device shares the PCI ID with the Samsung 970 Evo Plus that
does not need or want the quirks. Move the the quirk entry to the
core table based on the model number instead.
Fixes: bc360b0b16 ("nvme-pci: add quirks for Samsung X5 SSDs")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a6254d55e ]
This particular Kioxia device times out and aborts I/O during any load,
but it's more easily observable with discards (fstrim).
The device gets to a state that is also not possible to use
"nvme set-feature" to disable APST.
Booting with nvme_core.default_ps_max_latency=0 solves the issue.
We had a dozen or so of these devices behaving this same way in
customer environments.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e34a07c0ae ]
Commit 8a59f9d1e3 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
has moved the inet_csk_has_ulp(sk) check from sk_psock_init() to
the new tcp_bpf_update_proto() function. I'm guessing that this
was done to allow creating psocks for non-inet sockets.
Unfortunately the destruction path for psock includes the ULP
unwind, so we need to fail the sk_psock_init() itself.
Otherwise if ULP is already present we'll notice that later,
and call tcp_update_ulp() with the sk_proto of the ULP
itself, which will most likely result in the ULP looping
its callbacks.
Fixes: 8a59f9d1e3 ("sock: Introduce sk->sk_prot->psock_update_sk_prot()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Tested-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20220620191353.1184629-2-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
