[ Upstream commit 2069624dac ]
As noted elsewhere, various GPON SFP modules exhibit non-standard
TX-fault behaviour. In the tested case, the Huawei MA5671A, when used
in combination with a Marvell mv88e6085 switch, was found to
persistently assert TX-fault, resulting in the module being disabled.
This patch adds a quirk to ignore the SFP_F_TX_FAULT state, allowing the
module to function.
Change from v1: removal of erroneous return statment (Andrew Lunn)
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220502223315.1973376-1-mnhagan88@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b800528b97 ]
In xemaclite_open() function we are setting the max speed of
emaclite to 100Mb using phy_set_max_speed() function so,
there is no need to write the advertising registers to stop
giga-bit speed and the phy_start() function starts the
auto-negotiation so, there is no need to handle it separately
using advertising registers. Remove the phy_read and phy_write
of advertising registers in xemaclite_open() function.
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fbe467bcb ]
The max98090 driver has a custom put function for some controls which can
only be updated in certain circumstances which makes no effort to validate
that input is suitable for the control, allowing out of spec values to be
written to the hardware and presented to userspace. Fix this by returning
an error when invalid values are written.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220420193454.2647908-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d031a8866e ]
When a write cannot be carried out in full, gfs2_iomap_end() releases
blocks that have been allocated for this write but haven't been used.
To compute the end of the allocation, gfs2_iomap_end() incorrectly
rounded the end of the attempted write down to the next block boundary
to arrive at the end of the allocation. It would have to round up, but
the end of the allocation is also available as iomap->offset +
iomap->length, so just use that instead.
In addition, use round_up() for computing the start of the unused range.
Fixes: 64bc06bb32 ("gfs2: iomap buffered write support")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3740651bf7 ]
The commit cited below claims to fix a use-after-free condition after
tls_device_down. Apparently, the description wasn't fully accurate. The
context stayed alive, but ctx->netdev became NULL, and the offload was
torn down without a proper fallback, so a bug was present, but a
different kind of bug.
Due to misunderstanding of the issue, the original patch dropped the
refcount_dec_and_test line for the context to avoid the alleged
premature deallocation. That line has to be restored, because it matches
the refcount_inc_not_zero from the same function, otherwise the contexts
that survived tls_device_down are leaked.
This patch fixes the described issue by restoring refcount_dec_and_test.
After this change, there is no leak anymore, and the fallback to
software kTLS still works.
Fixes: c55dcdd435 ("net/tls: Fix use-after-free after the TLS device goes down and up")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220512091830.678684-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fa89ffbc0 ]
In the NIC ->probe() callback, ->mtd_probe() callback is called.
If NIC has 2 ports, ->probe() is called twice and ->mtd_probe() too.
In the ->mtd_probe(), which is efx_ef10_mtd_probe() it allocates and
initializes mtd partiion.
But mtd partition for sfc is shared data.
So that allocated mtd partition data from last called
efx_ef10_mtd_probe() will not be used.
Therefore it must be freed.
But it doesn't free a not used mtd partition data in efx_ef10_mtd_probe().
kmemleak reports:
unreferenced object 0xffff88811ddb0000 (size 63168):
comm "systemd-udevd", pid 265, jiffies 4294681048 (age 348.586s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffffa3767749>] kmalloc_order_trace+0x19/0x120
[<ffffffffa3873f0e>] __kmalloc+0x20e/0x250
[<ffffffffc041389f>] efx_ef10_mtd_probe+0x11f/0x270 [sfc]
[<ffffffffc0484c8a>] efx_pci_probe.cold.17+0x3df/0x53d [sfc]
[<ffffffffa414192c>] local_pci_probe+0xdc/0x170
[<ffffffffa4145df5>] pci_device_probe+0x235/0x680
[<ffffffffa443dd52>] really_probe+0x1c2/0x8f0
[<ffffffffa443e72b>] __driver_probe_device+0x2ab/0x460
[<ffffffffa443e92a>] driver_probe_device+0x4a/0x120
[<ffffffffa443f2ae>] __driver_attach+0x16e/0x320
[<ffffffffa4437a90>] bus_for_each_dev+0x110/0x190
[<ffffffffa443b75e>] bus_add_driver+0x39e/0x560
[<ffffffffa4440b1e>] driver_register+0x18e/0x310
[<ffffffffc02e2055>] 0xffffffffc02e2055
[<ffffffffa3001af3>] do_one_initcall+0xc3/0x450
[<ffffffffa33ca574>] do_init_module+0x1b4/0x700
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Fixes: 8127d661e7 ("sfc: Add support for Solarflare SFC9100 family")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20220512054709.12513-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7be130c5d ]
After commit 2d1f90f9ba ("net: dsa/bcm_sf2: fix incorrect usage of
state->link") the interface suspend path would call our mac_link_down()
call back which would forcibly set the link down, thus preventing
Wake-on-LAN packets from reaching our management port.
Fix this by looking at whether the port is enabled for Wake-on-LAN and
not clearing the link status in that case to let packets go through.
Fixes: 2d1f90f9ba ("net: dsa/bcm_sf2: fix incorrect usage of state->link")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220512021731.2494261-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b77c06655 ]
The interrupt controller supplying the Wake-on-LAN interrupt line maybe
modular on some platforms (irq-bcm7038-l1.c) and might be probed at a
later time than the GENET driver. We need to specifically check for
-EPROBE_DEFER and propagate that error to ensure that we eventually
fetch the interrupt descriptor.
Fixes: 9deb48b53e ("bcmgenet: add WOL IRQ check")
Fixes: 5b1f0e6294 ("net: bcmgenet: Avoid touching non-existent interrupt")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20220511031752.2245566-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b796475fd ]
Currently pedit tries to ensure that the accessed skb offset
is writable via skb_unclone(). The action potentially allows
touching any skb bytes, so it may end-up modifying shared data.
The above causes some sporadic MPTCP self-test failures, due to
this code:
tc -n $ns2 filter add dev ns2eth$i egress \
protocol ip prio 1000 \
handle 42 fw \
action pedit munge offset 148 u8 invert \
pipe csum tcp \
index 100
The above modifies a data byte outside the skb head and the skb is
a cloned one, carrying a TCP output packet.
This change addresses the issue by keeping track of a rough
over-estimate highest skb offset accessed by the action and ensuring
such offset is really writable.
Note that this may cause performance regressions in some scenarios,
but hopefully pedit is not in the critical path.
Fixes: db2c24175d ("act_pedit: access skb->data safely")
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Tested-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/1fcf78e6679d0a287dd61bb0f04730ce33b3255d.1652194627.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 671bb35c8e ]
smatch complains about
drivers/s390/net/lcs.c:1741 lcs_get_control() warn: variable dereferenced before check 'card->dev' (see line 1739)
Fixes: 27eb5ac8f0 ("[PATCH] s390: lcs driver bug fixes and improvements [1/2]")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c0b20587b ]
smatch complains about
drivers/s390/net/ctcm_mpc.c:1210 ctcmpc_unpack_skb() warn: possible memory leak of 'mpcginfo'
mpc_action_discontact() did not free mpcginfo. Consolidate the freeing in
ctcmpc_unpack_skb().
Fixes: 293d984f0e ("ctcm: infrastructure for replaced ctc driver")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c50c6867c ]
Found by cppcheck and smatch.
smatch complains about
drivers/s390/net/ctcm_sysfs.c:43 ctcm_buffer_write() warn: variable dereferenced before check 'priv' (see line 42)
Fixes: 3c09e2647b ("ctcm: rename READ/WRITE defines to avoid redefinitions")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41c240099f ]
The tools/testing/selftests/vm/Makefile uses the variable TARGETS
internally to generate a list of platform-specific binary build targets
suffixed with _{32,64}. When building the selftests using its own
Makefile directly, such as via the following command run in a kernel tree:
One receives an error such as the following:
make: Entering directory '/root/linux/tools/testing/selftests'
make --no-builtin-rules ARCH=x86 -C ../../.. headers_install
make[1]: Entering directory '/root/linux'
INSTALL ./usr/include
make[1]: Leaving directory '/root/linux'
make[1]: Entering directory '/root/linux/tools/testing/selftests/vm'
make[1]: *** No rule to make target 'vm.c', needed by '/root/linux/tools/testing/selftests/vm/vm_64'. Stop.
make[1]: Leaving directory '/root/linux/tools/testing/selftests/vm'
make: *** [Makefile:175: all] Error 2
make: Leaving directory '/root/linux/tools/testing/selftests'
The TARGETS variable passed to tools/testing/selftests/Makefile collides
with the TARGETS used in tools/testing/selftests/vm/Makefile, so rename
the latter to VMTARGETS, eliminating the collision with no functional
change.
Link: https://lkml.kernel.org/r/20220504213454.1282532-1-jsavitz@redhat.com
Fixes: f21fda8f64 ("selftests: vm: pkeys: fix multilib builds for x86")
Signed-off-by: Joel Savitz <jsavitz@redhat.com>
Acked-by: Nico Pache <npache@redhat.com>
Cc: Joel Savitz <jsavitz@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Sandipan Das <sandipan@linux.ibm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151d6dcbed ]
Building with SENSORS_LTQ_CPUTEMP=y with SOC_FALCON=y causes build
errors since FALCON does not support the same features as XWAY.
Change this symbol to depend on SOC_XWAY since that provides the
necessary interfaces.
Repairs these build errors:
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_enable':
../drivers/hwmon/ltq-cputemp.c:23:9: error: implicit declaration of function 'ltq_cgu_w32'; did you mean 'ltq_ebu_w32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c:23:21: error: implicit declaration of function 'ltq_cgu_r32'; did you mean 'ltq_ebu_r32'? [-Werror=implicit-function-declaration]
23 | ltq_cgu_w32(ltq_cgu_r32(CGU_GPHY1_CR) | CGU_TEMP_PD, CGU_GPHY1_CR);
../drivers/hwmon/ltq-cputemp.c: In function 'ltq_cputemp_probe':
../drivers/hwmon/ltq-cputemp.c:92:31: error: 'SOC_TYPE_VR9_2' undeclared (first use in this function)
92 | if (ltq_soc_type() != SOC_TYPE_VR9_2)
Fixes: 7074d0a927 ("hwmon: (ltq-cputemp) add cpu temp sensor driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Florian Eckert <fe@dev.tdt.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20220509234740.26841-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee1444b5e1 ]
The W=2 build pointed out that the code wasn't initializing all the
variables in the dim_cq_moder declarations with the struct initializers.
The net change here is zero since these structs were already static
const globals and were initialized with zeros by the compiler, but
removing compiler warnings has value in and of itself.
lib/dim/net_dim.c: At top level:
lib/dim/net_dim.c:54:9: warning: missing initializer for field ‘comps’ of ‘const struct dim_cq_moder’ [-Wmissing-field-initializers]
54 | NET_DIM_RX_EQE_PROFILES,
| ^~~~~~~~~~~~~~~~~~~~~~~
In file included from lib/dim/net_dim.c:6:
./include/linux/dim.h:45:13: note: ‘comps’ declared here
45 | u16 comps;
| ^~~~~
and repeats for the tx struct, and once you fix the comps entry then
the cq_period_mode field needs the same treatment.
Use the commonly accepted style to indicate to the compiler that we
know what we're doing, and add a comma at the end of each struct
initializer to clean up the issue, and use explicit initializers
for the fields we are initializing which makes the compiler happy.
While here and fixing these lines, clean up the code slightly with
a fix for the super long lines by removing the word "_MODERATION" from a
couple defines only used in this file.
Fixes: f8be17b81d ("lib/dim: Fix -Wunused-const-variable warnings")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20220507011038.14568-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 085d16d5f9 ]
Turns out that ever since this mount option was added, passing
`softreval` in NFS mount options cancelled all other flags while not
affecting the underlying flag `NFS_MOUNT_SOFTREVAL`.
Fixes: c74dfe97c1 ("NFS: Add mount option 'softreval'")
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49e6123c65 ]
It fixes memory leak in ring buffer change logic.
When ring buffer size is changed(ethtool -G eth0 rx 4096), sfc driver
works like below.
1. stop all channels and remove ring buffers.
2. allocates new buffer array.
3. allocates rx buffers.
4. start channels.
While the above steps are working, it skips some steps if the channel
doesn't have a ->copy callback function.
Due to ptp channel doesn't have ->copy callback, these above steps are
skipped for ptp channel.
It eventually makes some problems.
a. ptp channel's ring buffer size is not changed, it works only
1024(default).
b. memory leak.
The reason for memory leak is to use the wrong ring buffer values.
There are some values, which is related to ring buffer size.
a. efx->rxq_entries
- This is global value of rx queue size.
b. rx_queue->ptr_mask
- used for access ring buffer as circular ring.
- roundup_pow_of_two(efx->rxq_entries) - 1
c. rx_queue->max_fill
- efx->rxq_entries - EFX_RXD_HEAD_ROOM
These all values should be based on ring buffer size consistently.
But ptp channel's values are not.
a. efx->rxq_entries
- This is global(for sfc) value, always new ring buffer size.
b. rx_queue->ptr_mask
- This is always 1023(default).
c. rx_queue->max_fill
- This is new ring buffer size - EFX_RXD_HEAD_ROOM.
Let's assume we set 4096 for rx ring buffer,
normal channel ptp channel
efx->rxq_entries 4096 4096
rx_queue->ptr_mask 4095 1023
rx_queue->max_fill 4086 4086
sfc driver allocates rx ring buffers based on these values.
When it allocates ptp channel's ring buffer, 4086 ring buffers are
allocated then, these buffers are attached to the allocated array.
But ptp channel's ring buffer array size is still 1024(default)
and ptr_mask is still 1023 too.
So, 3062 ring buffers will be overwritten to the array.
This is the reason for memory leak.
Test commands:
ethtool -G <interface name> rx 4096
while :
do
ip link set <interface name> up
ip link set <interface name> down
done
In order to avoid this problem, it adds ->copy callback to ptp channel
type.
So that rx_queue->ptr_mask value will be updated correctly.
Fixes: 7c236c43b8 ("sfc: Add support for IEEE-1588 PTP")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5076fe404 ]
netlink_recvmsg() does not need to change transport header.
If transport header was needed, it should have been reset
by the producer (netlink_dump()), not the consumer(s).
The following trace probably happened when multiple threads
were using MSG_PEEK.
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
write to 0xffff88811e9f15b2 of 2 bytes by task 32012 on cpu 1:
skb_reset_transport_header include/linux/skbuff.h:2760 [inline]
netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978
sock_recvmsg_nosec net/socket.c:948 [inline]
sock_recvmsg net/socket.c:966 [inline]
__sys_recvfrom+0x204/0x2c0 net/socket.c:2097
__do_sys_recvfrom net/socket.c:2115 [inline]
__se_sys_recvfrom net/socket.c:2111 [inline]
__x64_sys_recvfrom+0x74/0x90 net/socket.c:2111
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
write to 0xffff88811e9f15b2 of 2 bytes by task 32005 on cpu 0:
skb_reset_transport_header include/linux/skbuff.h:2760 [inline]
netlink_recvmsg+0x1de/0x790 net/netlink/af_netlink.c:1978
____sys_recvmsg+0x162/0x2f0
___sys_recvmsg net/socket.c:2674 [inline]
__sys_recvmsg+0x209/0x3f0 net/socket.c:2704
__do_sys_recvmsg net/socket.c:2714 [inline]
__se_sys_recvmsg net/socket.c:2711 [inline]
__x64_sys_recvmsg+0x42/0x50 net/socket.c:2711
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff -> 0x0000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 32005 Comm: syz-executor.4 Not tainted 5.18.0-rc1-syzkaller-00328-ge1f700ebd6be-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20220505161946.2867638-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab244be47a ]
If successful ida_simple_get() calls are not undone when needed, some
additional memory may be allocated and wasted.
Here, an ID between 0 and MAX_INT is required. If this ID is >=100, it is
not taken into account and is wasted. It should be released.
Instead of calling ida_simple_remove(), take advantage of the 'max'
parameter to require the ID not to be too big. Should it be too big, it
is not allocated and don't need to be freed.
While at it, use ida_alloc_xxx()/ida_free() instead to
ida_simple_get()/ida_simple_remove().
The latter is deprecated and more verbose.
Fixes: db1a0ae214 ("drm/nouveau/bl: Assign different names to interfaces")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Lyude Paul <lyude@redhat.com>
[Fixed formatting warning from checkpatch]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9ba85bca59df6813dc029e743a836451d5173221.1644386541.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93a8417088 ]
Given the following order of operations:
(1) we add filter A using tc-flower
(2) we send a packet that matches it
(3) we read the filter's statistics to find a hit count of 1
(4) we add a second filter B with a higher preference than A, and A
moves one position to the right to make room in the TCAM for it
(5) we send another packet, and this matches the second filter B
(6) we read the filter statistics again.
When this happens, the hit count of filter A is 2 and of filter B is 1,
despite a single packet having matched each filter.
Furthermore, in an alternate history, reading the filter stats a second
time between steps (3) and (4) makes the hit count of filter A remain at
1 after step (6), as expected.
The reason why this happens has to do with the filter->stats.pkts field,
which is written to hardware through the call path below:
vcap_entry_set
/ | \
/ | \
/ | \
/ | \
es0_entry_set is1_entry_set is2_entry_set
\ | /
\ | /
\ | /
vcap_data_set(data.counter, ...)
The primary role of filter->stats.pkts is to transport the filter hit
counters from the last readout all the way from vcap_entry_get() ->
ocelot_vcap_filter_stats_update() -> ocelot_cls_flower_stats().
The reason why vcap_entry_set() writes it to hardware is so that the
counters (saturating and having a limited bit width) are cleared
after each user space readout.
The writing of filter->stats.pkts to hardware during the TCAM entry
movement procedure is an unintentional consequence of the code design,
because the hit count isn't up to date at this point.
So at step (4), when filter A is moved by ocelot_vcap_filter_add() to
make room for filter B, the hardware hit count is 0 (no packet matched
on it in the meantime), but filter->stats.pkts is 1, because the last
readout saw the earlier packet. The movement procedure programs the old
hit count back to hardware, so this creates the impression to user space
that more packets have been matched than they really were.
The bug can be seen when running the gact_drop_and_ok_test() from the
tc_actions.sh selftest.
Fix the issue by reading back the hit count to tmp->stats.pkts before
migrating the VCAP filter. Sure, this is a best-effort technique, since
the packets that hit the rule between vcap_entry_get() and
vcap_entry_set() won't be counted, but at least it allows the counters
to be reliably used for selftests where the traffic is under control.
The vcap_entry_get() name is a bit unintuitive, but it only reads back
the counter portion of the TCAM entry, not the entire entry.
The index from which we retrieve the counter is also a bit unintuitive
(i - 1 during add, i + 1 during del), but this is the way in which TCAM
entry movement works. The "entry index" isn't a stored integer for a
TCAM filter, instead it is dynamically computed by
ocelot_vcap_block_get_filter_index() based on the entry's position in
the &block->rules list. That position (as well as block->count) is
automatically updated by ocelot_vcap_filter_add_to_block() on add, and
by ocelot_vcap_block_remove_filter() on del. So "i" is the new filter
index, and "i - 1" or "i + 1" respectively are the old addresses of that
TCAM entry (we only support installing/deleting one filter at a time).
Fixes: b596229448 ("net: mscc: ocelot: Add support for tcam")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 477d2b9162 ]
Once the CPU port was added to the destination port mask of a packet, it
can never be cleared, so even packets marked as dropped by the MASK_MODE
of a VCAP IS2 filter will still reach it. This is why we need the
OCELOT_POLICER_DISCARD to "kill dropped packets dead" and make software
stop seeing them.
We disallow policer rules from being put on any other chain than the one
for the first lookup, but we don't do this for "drop" rules, although we
should. This change is merely ascertaining that the rules dont't
(completely) work and letting the user know.
The blamed commit is the one that introduced the multi-chain architecture
in ocelot. Prior to that, we should have always offloaded the filters to
VCAP IS2 lookup 0, where they did work.
Fixes: 1397a2eb52 ("net: mscc: ocelot: create TCAM skeleton from tc filter chains")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6741e11880 ]
The VCAP IS2 TCAM is looked up twice per packet, and each filter can be
configured to only match during the first, second lookup, or both, or
none.
The blamed commit wrote the code for making VCAP IS2 filters match only
on the given lookup. But right below that code, there was another line
that explicitly made the lookup a "don't care", and this is overwriting
the lookup we've selected. So the code had no effect.
Some of the more noticeable effects of having filters match on both
lookups:
- in "tc -s filter show dev swp0 ingress", we see each packet matching a
VCAP IS2 filter counted twice. This throws off scripts such as
tools/testing/selftests/net/forwarding/tc_actions.sh and makes them
fail.
- a "tc-drop" action offloaded to VCAP IS2 needs a policer as well,
because once the CPU port becomes a member of the destination port
mask of a packet, nothing removes it, not even a PERMIT/DENY mask mode
with a port mask of 0. But VCAP IS2 rules with the POLICE_ENA bit in
the action vector can only appear in the first lookup. What happens
when a filter matches both lookups is that the action vector is
combined, and this makes the POLICE_ENA bit ineffective, since the
last lookup in which it has appeared is the second one. In other
words, "tc-drop" actions do not drop packets for the CPU port, dropped
packets are still seen by software unless there was an FDB entry that
directed those packets to some other place different from the CPU.
The last bit used to work, because in the initial commit b596229448
("net: mscc: ocelot: Add support for tcam"), we were writing the FIRST
field of the VCAP IS2 half key with a 1, not with a "don't care".
The change to "don't care" was made inadvertently by me in commit
c1c3993edb ("net: mscc: ocelot: generalize existing code for VCAP"),
which I just realized, and which needs a separate fix from this one,
for "stable" kernels that lack the commit blamed below.
Fixes: 226e9cd82a ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16bbebd356 ]
ocelot_vcap_filter_del() works by moving the next filters over the
current one, and then deleting the last filter by calling vcap_entry_set()
with a del_filter which was specially created by memsetting its memory
to zeroes. vcap_entry_set() then programs this to the TCAM and action
RAM via the cache registers.
The problem is that vcap_entry_set() is a dispatch function which looks
at del_filter->block_id. But since del_filter is zeroized memory, the
block_id is 0, or otherwise said, VCAP_ES0. So practically, what we do
is delete the entry at the same TCAM index from VCAP ES0 instead of IS1
or IS2.
The code was not always like this. vcap_entry_set() used to simply be
is2_entry_set(), and then, the logic used to work.
Restore the functionality by populating the block_id of the del_filter
based on the VCAP block of the filter that we're deleting. This makes
vcap_entry_set() know what to do.
Fixes: 1397a2eb52 ("net: mscc: ocelot: create TCAM skeleton from tc filter chains")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86af062f40 ]
Currently MBSSID parameters in struct ieee80211_bss_conf
are not reset upon connection. This could be problematic
with some drivers in a scenario where the device first
connects to a non-transmit BSS and then connects to a
transmit BSS of a Multi BSS AP. The MBSSID parameters
which are set after connecting to a non-transmit BSS will
not be reset and the same parameters will be passed on to
the driver during the subsequent connection to a transmit
BSS of a Multi BSS AP.
For example, firmware running on the ath11k device uses the
Multi BSS data for tracking the beacon of a non-transmit BSS
and reports the driver when there is a beacon miss. If we do
not reset the MBSSID parameters during the subsequent
connection to a transmit BSS, then the driver would have
wrong MBSSID data and FW would be looking for an incorrect
BSSID in the MBSSID beacon of a Multi BSS AP and reports
beacon loss leading to an unstable connection.
Reset the MBSSID parameters upon every connection to solve this
problem.
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Link: https://lore.kernel.org/r/20220428052744.27040-1-quic_mpubbise@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3481551f03 ]
This driver doesn't have of_match_table. This makes the kernel module
tmp401.ko lack alias patterns (e.g: of:N*T*Cti,tmp411) to match DT node
of the supported devices hence this kernel module will not be
automatically loaded.
After adding of_match_table to this driver, the folllowing alias will be
added into tmp401.ko.
$ modinfo drivers/hwmon/tmp401.ko
filename: drivers/hwmon/tmp401.ko
......
author: Hans de Goede <hdegoede@redhat.com>
alias: of:N*T*Cti,tmp435C*
alias: of:N*T*Cti,tmp435
alias: of:N*T*Cti,tmp432C*
alias: of:N*T*Cti,tmp432
alias: of:N*T*Cti,tmp431C*
alias: of:N*T*Cti,tmp431
alias: of:N*T*Cti,tmp411C*
alias: of:N*T*Cti,tmp411
alias: of:N*T*Cti,tmp401C*
alias: of:N*T*Cti,tmp401
......
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Signed-off-by: Camel Guo <camel.guo@axis.com>
Link: https://lore.kernel.org/r/20220503114333.456476-1-camel.guo@axis.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a063f2fba3 ]
The receiving interface might have used GRO to receive more fragments than
MAX_SKB_FRAGS fragments. In this case, these will not be stored in
skb_shinfo(skb)->frags but merged into the frag list.
batman-adv relies on the function skb_split to split packets up into
multiple smaller packets which are not larger than the MTU on the outgoing
interface. But this function cannot handle frag_list entries and is only
operating on skb_shinfo(skb)->frags. If it is still trying to split such an
skb and xmit'ing it on an interface without support for NETIF_F_FRAGLIST,
then validate_xmit_skb() will try to linearize it. But this fails due to
inconsistent information. And __pskb_pull_tail will trigger a BUG_ON after
skb_copy_bits() returns an error.
In case of entries in frag_list, just linearize the skb before operating on
it with skb_split().
Reported-by: Felix Kaechele <felix@kaechele.ca>
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Felix Kaechele <felix@kaechele.ca>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2771739a71 upstream.
The D-cache maintenance inside move_to_new_page() only consider one
page, there is still D-cache maintenance issue for tail pages of
compound page (e.g. THP or HugeTLB).
THP migration is only enabled on x86_64, ARM64 and powerpc, while
powerpc and arm64 need to maintain the consistency between I-Cache and
D-Cache, which depends on flush_dcache_page() to maintain the
consistency between I-Cache and D-Cache.
But there is no issues on arm64 and powerpc since they already considers
the compound page cache flushing in their icache flush function.
HugeTLB migration is enabled on arm, arm64, mips, parisc, powerpc,
riscv, s390 and sh, while arm has handled the compound page cache flush
in flush_dcache_page(), but most others do not.
In theory, the issue exists on many architectures. Fix this by not
using flush_dcache_folio() since it is not backportable.
Link: https://lkml.kernel.org/r/20220210123058.79206-3-songmuchun@bytedance.com
Fixes: 290408d4a2 ("hugetlb: hugepage migration core")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Zi Yan <ziy@nvidia.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Fam Zheng <fam.zheng@bytedance.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Xiongchun Duan <duanxiongchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 103a2f3255 upstream.
Set a size limit of 8 bytes of the written buffer to "hdev->name"
including the terminating null byte, as the size of "hdev->name" is 8
bytes. If an id value which is greater than 9999 is allocated,
then the "snprintf(hdev->name, sizeof(hdev->name), "hci%d", id)"
function call would lead to a truncation of the id value in decimal
notation.
Set an explicit maximum id parameter in the id allocation function call.
The id allocation function defines the maximum allocated id value as the
maximum id parameter value minus one. Therefore, HCI_MAX_ID is defined
as 10000.
Signed-off-by: Itay Iellin <ieitayie@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a64ef042e upstream.
A new warning in clang points out two places in this driver where
boolean expressions are being used with a bitwise OR instead of a
logical one:
drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: note: cast one or both operands to int to silence this warning
drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: note: cast one or both operands to int to silence this warning
2 errors generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not. In this case, it does not seem like
short circuiting is harmful so implement the suggested fix of changing
to a logical operation to fix the warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/1479
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018193101.2340261-1-nathan@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f1e87b4dc upstream.
Fixes the following W=1 kernel build warning(s):
from drivers/block/drbd/drbd_nl.c:24:
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_set_role’:
drivers/block/drbd/drbd_nl.c:793:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c:795:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_attach’:
drivers/block/drbd/drbd_nl.c:1965:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_connect’:
drivers/block/drbd/drbd_nl.c:2690:10: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
drivers/block/drbd/drbd_nl.c: In function ‘drbd_adm_disconnect’:
drivers/block/drbd/drbd_nl.c:2803:11: warning: implicit conversion from ‘enum drbd_state_rv’ to ‘enum drbd_ret_code’ [-Wenum-conversion]
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: drbd-dev@lists.linbit.com
Cc: linux-block@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210312105530.2219008-8-lee.jones@linaro.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d422c6c064 upstream.
When building xway_defconfig with clang:
arch/mips/lantiq/prom.c:82:23: error: array comparison always evaluates
to true [-Werror,-Wtautological-compare]
else if (__dtb_start != __dtb_end)
^
1 error generated.
These are not true arrays, they are linker defined symbols, which are
just addresses. Using the address of operator silences the warning
and does not change the resulting assembly with either clang/ld.lld
or gcc/ld (tested with diff + objdump -Dr). Do the same thing across
the entire MIPS subsystem to ensure there are no more warnings around
this type of comparison.
Link: https://github.com/ClangBuiltLinux/linux/issues/1232
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
