[ Upstream commit c8da1d15b8 ]
DesignWare I2C controller was observed running at 105.93kHz rather
than the specified 100kHz. Adjust device tree settings to bring it
within spec (a slightly conservative 98 MHz).
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b943f17e06 ]
In lio_enable_irq, the pkt_in_done count register was being cleared to
zero. However, there could be some completed instructions which were not
yet processed due to budget and limit constraints.
So, only write this register with the number of actual completions
that were processed.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64858773d7 ]
This patch adds missing properties to the CODEC and sound nodes, so the
audio will work also on Snow rev5 Chromebook. This patch is an extension
to the commit e9eefc3f8c ("ARM: dts: exynos: Add missing clock and
DAI properties to the max98095 node in Snow Chromebook")
and commit 6ab569936d ("ARM: dts: exynos: Enable HDMI audio on Snow
Chromebook"). It has been reported that such changes work fine on the
rev5 board too.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[krzk: Fixed typo in phandle to &max98090]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21cb5a2748 ]
HDMI-HPD was set active low, moreover by default pincontrol chip sets
pull-down on the pin. As a result HDMI driver assumes TV is always
connected regardless of actual state. The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 620375c8fd ]
HDMI-DDC for unknown reasons doesn't work with Exynos I2C controllers.
Fortunately i2c-gpio comes to the rescue.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1b1e9880f ]
25Mhz MCLK which was earlier used was of spread type.
Thus, we were not getting accurate rate. The 48Mhz system
clk is of non-spread type and we are changing to it to get
accurate rate.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dadfab7272 ]
Return value of request_irq() was irgnored. Fix this and report
the failure if any
Fixes: 6dc4fa179f ("ASoC: meson: add axg fifo base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e33ffbd9cd ]
If the CPU DAI does not initialise rate_max, say if using
using KNOT or CONTINUOUS, then the rate_max field will be
initialised to 0. A value of zero in the rate_max field of
the hardware runtime will cause the sound card to support no
sample rates at all. Obviously this is not desired, just a
different mechanism is being used to apply the constraints. As
such update the setting of rate_max in dpcm_init_runtime_hw
to be consistent with the non-DPCM cases and set rate_max to
UINT_MAX if nothing is defined on the CPU DAI.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5cd7e9cf5 ]
devm_pinctrl_get will only return NULL in the case that pinctrl
is not built into the kernel and all the pinctrl functions used
by the DAPM core are appropriately stubbed for that case. There
is no need to error out of snd_soc_dapm_new_control_unlocked
if pinctrl isn't built into the kernel, so change the
IS_ERR_OR_NULL to just an IS_ERR.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f36cb36c9 ]
The GFS2_RDF_UPTODATE flag in the rgrp is used to determine when
a rgrp buffer is valid. It's cleared when the glock is invalidated,
signifying that the buffer data is now invalid. But before this
patch, function update_rgrp_lvb was setting the flag when it
determined it had a valid lvb. But that's an invalid assumption:
just because you have a valid lvb doesn't mean you have valid
buffers. After all, another node may have made the lvb valid,
and this node just fetched it from the glock via dlm.
Consider this scenario:
1. The file system is mounted with RGRPLVB option.
2. In gfs2_inplace_reserve it locks the rgrp glock EX, but thanks
to GL_SKIP, it skips the gfs2_rgrp_bh_get.
3. Since loops == 0 and the allocation target (ap->target) is
bigger than the largest known chunk of blocks in the rgrp
(rs->rs_rbm.rgd->rd_extfail_pt) it skips that rgrp and bypasses
the call to gfs2_rgrp_bh_get there as well.
4. update_rgrp_lvb sees the lvb MAGIC number is valid, so bypasses
gfs2_rgrp_bh_get, but it still sets sets GFS2_RDF_UPTODATE due
to this invalid assumption.
5. The next time update_rgrp_lvb is called, it sees the bit is set
and just returns 0, assuming both the lvb and rgrp are both
uptodate. But since this is a smaller allocation, or space has
been freed by another node, thus adjusting the lvb values,
it decides to use the rgrp for allocations, with invalid rd_free
due to the fact it was never updated.
This patch changes update_rgrp_lvb so it doesn't set the UPTODATE
flag anymore. That way, it has no choice but to fetch the latest
values.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd2a981777 ]
Once reset is issued, the driver loses all control queue interfaces.
Exercising control queue operations during reset is incorrect and
may result in long timeouts.
This patch introduces a new field 'reset_ongoing' in the hw structure.
This is set to 1 by the core driver when it receives a reset interrupt.
ice_sq_send_cmd checks reset_ongoing before actually issuing the control
queue operation. If a reset is in progress, it returns a soft error code
(ICE_ERR_RESET_PENDING) to the caller. The caller may or may not have to
take any action based on this return. Once the driver knows that the
reset is done, it has to set reset_ongoing back to 0. This will allow
control queue operations to be posted to the hardware again.
This "bail out" logic was specifically added to ice_sq_send_cmd (which
is pretty low level function) so that we have one solution in one place
that applies to all types of control queues.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff2b13213a ]
Align Request Resource Ownership AQ command (0x0008) to the latest
specification. This includes:
- Correcting the resource IDs for the Global Cfg and Change locks.
- new enum ICE_CHANGE_LOCK_RES_ID
- new enum ICE_GLOBAL_CFG_LOCK_RES_ID
- Altering the flow for Global Config Lock to allow only the first PF to
download the package.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34d5629d2c ]
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.
There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df2b53884a ]
In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 596bdbcce9 ]
use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a65064abd ]
Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9c52fd17c ]
Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58da3b4230 ]
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.
Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8e131542b ]
snd_seq_system_client_init() doesn't check the errors returned from
its port creations. Let's do it properly and handle the error paths.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7417844b63 ]
When REGULATORY_COUNTRY_IE_IGNORE is set, __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().
After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().
To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.
Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 962341b54b ]
When we have first case to fall through it's not enough to put
single comment there to satisfy compiler. Instead of doing that,
return fall back value directly from default case.
This to avoid following warnings:
drivers/extcon/extcon-intel-cht-wc.c: In function ‘cht_wc_extcon_get_charger’:
include/linux/device.h:1420:2: warning: this statement may fall through [-Wimplicit-fallthrough=]
_dev_warn(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:148:3: note: in expansion of macro ‘dev_warn’
dev_warn(ext->dev,
^~~~~~~~
drivers/extcon/extcon-intel-cht-wc.c:152:2: note: here
case CHT_WC_USBSRC_TYPE_SDP:
^~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 777d8ae56d ]
devm_kcalloc() returns NULL, it never returns error pointers. In the
current code we would return PTR_ERR(NULL) which is success, instead of
returning the -ENOMEM error code.
Fixes: a0a1a1ba30 ("rtc: sysfs: facilitate attribute add to rtc device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 441f61e3aa ]
Update the SATA device nodes on R-Car H1, H2, and M2-W to use a 2 MiB
I/O space, as specified in Rev.1.0 of the R-Car H1 and R-Car Gen2
hardware user manuals.
See also commit e9f0089b2d ("arm64: dts: r8a7795: Correct SATA
device size to 2MiB").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33e2641819 ]
get_seconds() and do_gettimeofday() are only used by a few modules now any
more (waiting for the respective patches to get accepted), and they are
among the last holdouts of code that is not y2038 safe in the core kernel.
Move the implementation into the timekeeping32.h header to clean up
the core kernel and isolate the old interfaces further.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13136a47a0 ]
Implement support for the PMC_IMPL_E_33V_PWR register which replaces
PMC_PWR_DET register interface of the SoC generations preceding
Tegra186. Also add the voltage bit offsets to the tegra186_io_pads[]
table and the AO_HV pad.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f128fa41f ]
The "frames" variable is unsigned so the error handling doesn't work
properly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 480f58cdbe ]
According to the NanoPi-A64 schematics, DCDC1 is connected to a voltage
rail named "VDD_SYS_3.3V". All users seem to expect 3.3V here: the
Ethernet PHY, the uSD card slot, the camera interface and the GPIO pins
on the headers.
Fix up the voltage on the regulator to lift it up to 3.3V.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93366b49a3 ]
The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09b964afca ]
The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1c815f4b2 ]
In case of error, we can dereference uninitialized 'adev'
drivers/soundwire/intel_init.c:154 sdw_intel_acpi_cb()
error: uninitialized symbol 'adev'.
Fix that by not using adev for warn print and make it pr_err.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a306a0e4a5 ]
Deferred messages are async messages used to synchronize
transitions mostly while doing a bank switch on multi links.
On successful transitions these messages are marked complete
and thereby confirming that all the buses performed bank switch
successfully.
So, initialize the completion structure for the same.
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58c0f79887 ]
Currently the register offset of the PWM bus gate in Allwinner H6 clock
driver is wrong.
Fix this issue.
Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Rongyi Chen <chenyi@tt-cool.com>
[Icenowy: refactor commit message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd1d395070 ]
When continuously running wifi up/down sequence, the napi poll
can be scheduled after the CE buffers being freed by ath10k_pci_flush
Steps:
In a certain condition, during wifi down below scenario might occur.
ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize).
In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60
Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db878f76b9 ]
DT nodes may have a 'status' property which, if set to anything other
than 'ok' or 'okay', indicates to the OS that the DT node should be
treated as if it was not present. So add that missing logic to the
OP-TEE driver.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1ec080250 ]
After finding a reasonable gain, the function converts the configured
gain to a gain configuration option selector enum max9611_csa_gain.
Make the conversion clearly visible by using an explicit cast. This
also avoids a warning seen with clang:
drivers/iio/adc/max9611.c:292:16: warning: implicit conversion from
enumeration type 'enum max9611_conf_ids' to different enumeration
type 'enum max9611_csa_gain' [-Wenum-conversion]
*csa_gain = gain_selectors[i];
~ ^~~~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0362f326d8 upstream.
An exiting task might belong to an offline cgroup. In this case an
attempt to grab a cgroup reference from the task can end up with an
infinite loop in hugetlb_cgroup_charge_cgroup(), because neither the
cgroup will become online, neither the task will be migrated to a live
cgroup.
Fix this by switching over to css_tryget(). As css_tryget_online()
can't guarantee that the cgroup won't go offline, in most cases the
check doesn't make sense. In this particular case users of
hugetlb_cgroup_charge_cgroup() are not affected by this change.
A similar problem is described by commit 18fa84a2db ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Link: http://lkml.kernel.org/r/20191106225131.3543616-2-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00d484f354 upstream.
We've encountered a rcu stall in get_mem_cgroup_from_mm():
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 33-....: (21000 ticks this GP) idle=6c6/1/0x4000000000000002 softirq=35441/35441 fqs=5017
(t=21031 jiffies g=324821 q=95837) NMI backtrace for cpu 33
<...>
RIP: 0010:get_mem_cgroup_from_mm+0x2f/0x90
<...>
__memcg_kmem_charge+0x55/0x140
__alloc_pages_nodemask+0x267/0x320
pipe_write+0x1ad/0x400
new_sync_write+0x127/0x1c0
__kernel_write+0x4f/0xf0
dump_emit+0x91/0xc0
writenote+0xa0/0xc0
elf_core_dump+0x11af/0x1430
do_coredump+0xc65/0xee0
get_signal+0x132/0x7c0
do_signal+0x36/0x640
exit_to_usermode_loop+0x61/0xd0
do_syscall_64+0xd4/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The problem is caused by an exiting task which is associated with an
offline memcg. We're iterating over and over in the do {} while
(!css_tryget_online()) loop, but obviously the memcg won't become online
and the exiting task won't be migrated to a live memcg.
Let's fix it by switching from css_tryget_online() to css_tryget().
As css_tryget_online() cannot guarantee that the memcg won't go offline,
the check is usually useless, except some rare cases when for example it
determines if something should be presented to a user.
A similar problem is described by commit 18fa84a2db ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Johannes:
: The bug aside, it doesn't matter whether the cgroup is online for the
: callers. It used to matter when offlining needed to evacuate all charges
: from the memcg, and so needed to prevent new ones from showing up, but we
: don't care now.
Link: http://lkml.kernel.org/r/20191106225131.3543616-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Shakeel Butt <shakeeb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Michal Koutn <mkoutny@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a85dfc305a upstream.
Commit d883544515 ("mm: mempolicy: make the behavior consistent when
MPOL_MF_MOVE* and MPOL_MF_STRICT were specified") fixed the return value
of mbind() for a couple of corner cases. But, it altered the errno for
some other cases, for example, mbind() should return -EFAULT when part
or all of the memory range specified by nodemask and maxnode points
outside your accessible address space, or there was an unmapped hole in
the specified memory range specified by addr and len.
Fix this by preserving the errno returned by queue_pages_range(). And,
the pagelist may be not empty even though queue_pages_range() returns
error, put the pages back to LRU since mbind_range() is not called to
really apply the policy so those pages should not be migrated, this is
also the old behavior before the problematic commit.
Link: http://lkml.kernel.org/r/1572454731-3925-1-git-send-email-yang.shi@linux.alibaba.com
Fixes: d883544515 ("mm: mempolicy: make the behavior consistent when MPOL_MF_MOVE* and MPOL_MF_STRICT were specified")
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Reported-by: Li Xinhai <lixinhai.lxh@gmail.com>
Reviewed-by: Li Xinhai <lixinhai.lxh@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org> [4.19 and 5.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e7120d79e upstream.
For both PASID-based-Device-TLB Invalidate Descriptor and
Device-TLB Invalidate Descriptor, the Physical Function Source-ID
value is split according to this layout:
PFSID[3:0] is set at offset 12 and PFSID[15:4] is put at offset 52.
Fix the part laid out at offset 52.
Fixes: 0f725561e1 ("iommu/vt-d: Add definitions for PFSID")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: stable@vger.kernel.org # v4.19+
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40a1dcee2d upstream.
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
