[ Upstream commit da8e393e23 ]
vc4_drv isn't necessarily under the /soc node in DT as it is a
virtual device, but it is the one that does the allocations.
The DMA addresses are consumed by primarily the HVS or V3D, and
those require VideoCore cache alias address mapping, and so will be
under /soc.
During probe find the a suitable device node for HVS or V3D,
and adopt the DMA configuration of that node.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-2-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5539722eb ]
The Elantech touchscreen/digitizer in the Surface Go mistakenly reports
having a battery. This results in a low battery message every time you
try to use the pen.
This patch adds a quirk to ignore the non-existent battery and
gets rid of the false low battery messages.
Signed-off-by: Zoltan Tamas Vajda <zoltan.tamas.vajda@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit decfe496fe ]
Battery status is reported for the HP Spectre X360 Convertible 15-df0xxx
even if it does not have a battery. Prevent it to always report the
battery as low.
Signed-off-by: Elia Devito <eliadevito@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81cc7e51c4 ]
Mipi dsi panel drivers can use mipi_dsi_dcs_{set,get}_display_brightness()
to request backlight changes.
This can be done during panel initialization (dsi is in command mode)
or afterwards (dsi is in Video Mode).
When the DSI is in Video Mode, all commands are rejected.
Detect current DSI mode in mtk_dsi_host_transfer() and switch modes
temporarily to allow commands to be sent.
Signed-off-by: Julien STEPHAN <jstephan@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2af28b241e upstream.
trace_spmi_write_begin() and trace_spmi_read_end() both call
memcpy() with a length of "len + 1". This leads to one extra
byte being read beyond the end of the specified buffer. Fix
this out-of-bound memory access by using a length of "len"
instead.
Here is a KASAN log showing the issue:
BUG: KASAN: stack-out-of-bounds in trace_event_raw_event_spmi_read_end+0x1d0/0x234
Read of size 2 at addr ffffffc0265b7540 by task thermal@2.0-ser/1314
...
Call trace:
dump_backtrace+0x0/0x3e8
show_stack+0x2c/0x3c
dump_stack_lvl+0xdc/0x11c
print_address_description+0x74/0x384
kasan_report+0x188/0x268
kasan_check_range+0x270/0x2b0
memcpy+0x90/0xe8
trace_event_raw_event_spmi_read_end+0x1d0/0x234
spmi_read_cmd+0x294/0x3ac
spmi_ext_register_readl+0x84/0x9c
regmap_spmi_ext_read+0x144/0x1b0 [regmap_spmi]
_regmap_raw_read+0x40c/0x754
regmap_raw_read+0x3a0/0x514
regmap_bulk_read+0x418/0x494
adc5_gen3_poll_wait_hs+0xe8/0x1e0 [qcom_spmi_adc5_gen3]
...
__arm64_sys_read+0x4c/0x60
invoke_syscall+0x80/0x218
el0_svc_common+0xec/0x1c8
...
addr ffffffc0265b7540 is located in stack of task thermal@2.0-ser/1314 at offset 32 in frame:
adc5_gen3_poll_wait_hs+0x0/0x1e0 [qcom_spmi_adc5_gen3]
this frame has 1 object:
[32, 33) 'status'
Memory state around the buggy address:
ffffffc0265b7400: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
ffffffc0265b7480: 04 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
>ffffffc0265b7500: 00 00 00 00 f1 f1 f1 f1 01 f3 f3 f3 00 00 00 00
^
ffffffc0265b7580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0265b7600: f1 f1 f1 f1 01 f2 07 f2 f2 f2 01 f3 00 00 00 00
==================================================================
Fixes: a9fce37481 ("spmi: add command tracepoints for SPMI")
Cc: stable@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20220627235512.2272783-1-quic_collinsd@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20aac6c609 upstream.
Validate mount_lock seqcount as soon as we cross into mount in RCU
mode. Sure, ->mnt_root is pinned and will remain so until we
do rcu_read_unlock() anyway, and we will eventually fail to unlazy if
the mount_lock had been touched, but we might run into a hard error
(e.g. -ENOENT) before trying to unlazy. And it's possible to end
up with RCU pathwalk racing with rename() and umount() in a way
that would fail with -ENOENT while non-RCU pathwalk would've
succeeded with any timings.
Once upon a time we hadn't needed that, but analysis had been subtle,
brittle and went out of window as soon as RENAME_EXCHANGE had been
added.
It's narrow, hard to hit and won't get you anything other than
stray -ENOENT that could be arranged in much easier way with the
same priveleges, but it's a bug all the same.
Cc: stable@kernel.org
X-sky-is-falling: unlikely
Fixes: da1ce0670c "vfs: add cross-rename"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e362359ace upstream.
Commit 55e8c8eb2c ("posix-cpu-timers: Store a reference to a pid not a
task") started looking up tasks by PID when deleting a CPU timer.
When a non-leader thread calls execve, it will switch PIDs with the leader
process. Then, as it calls exit_itimers, posix_cpu_timer_del cannot find
the task because the timer still points out to the old PID.
That means that armed timers won't be disarmed, that is, they won't be
removed from the timerqueue_list. exit_itimers will still release their
memory, and when that list is later processed, it leads to a
use-after-free.
Clean up the timers from the de-threaded task before freeing them. This
prevents a reported use-after-free.
Fixes: 55e8c8eb2c ("posix-cpu-timers: Store a reference to a pid not a task")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220809170751.164716-1-cascardo@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a2ba42cbd upstream.
The bitops compile-time optimization series revealed one more
problem in olpc-xo1-sci.c:send_ebook_state(), resulted in GCC
warnings:
arch/x86/platform/olpc/olpc-xo1-sci.c: In function 'send_ebook_state':
arch/x86/platform/olpc/olpc-xo1-sci.c:83:63: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
83 | if (!!test_bit(SW_TABLET_MODE, ebook_switch_idev->sw) == state)
| ^~
arch/x86/platform/olpc/olpc-xo1-sci.c:83:13: note: add parentheses around left hand side expression to silence this warning
Despite this code working as intended, this redundant double
negation of boolean value, together with comparing to `char`
with no explicit conversion to bool, makes compilers think
the author made some unintentional logical mistakes here.
Make it the other way around and negate the char instead
to silence the warnings.
Fixes: d2aa37411b ("x86/olpc/xo1/sci: Produce wakeup events for buttons and switches")
Cc: stable@vger.kernel.org # 3.5+
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6cfcdda8c upstream.
AMD's "Technical Guidance for Mitigating Branch Type Confusion,
Rev. 1.0 2022-07-12" whitepaper, under section 6.1.2 "IBPB On
Privileged Mode Entry / SMT Safety" says:
Similar to the Jmp2Ret mitigation, if the code on the sibling thread
cannot be trusted, software should set STIBP to 1 or disable SMT to
ensure SMT safety when using this mitigation.
So, like already being done for retbleed=unret, and now also for
retbleed=ibpb, force STIBP on machines that have it, and report its SMT
vulnerability status accordingly.
[ bp: Remove the "we" and remove "[AMD]" applicability parameter which
doesn't work here. ]
Fixes: 3ebc170068 ("x86/bugs: Add retbleed=ibpb")
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org # 5.10, 5.15, 5.19
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Link: https://lore.kernel.org/r/20220804192201.439596-1-kim.phillips@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4da8c5f768 upstream.
Case (1):
The only waiter on wka_port->completion_wq is zfcp_fc_wka_port_get()
trying to open a WKA port. As such it should only be woken up by WKA port
*open* responses, not by WKA port close responses.
Case (2):
A close WKA port response coming in just after having sent a new open WKA
port request and before blocking for the open response with wait_event()
in zfcp_fc_wka_port_get() erroneously renders the wait_event a NOP
because the close handler overwrites wka_port->status. Hence the
wait_event condition is erroneously true and it does not enter blocking
state.
With non-negligible probability, the following time space sequence happens
depending on timing without this fix:
user process ERP thread zfcp work queue tasklet system work queue
============ ========== =============== ======= =================
$ echo 1 > online
zfcp_ccw_set_online
zfcp_ccw_activate
zfcp_erp_adapter_reopen
msleep scan backoff zfcp_erp_strategy
| ...
| zfcp_erp_action_cleanup
| ...
| queue delayed scan_work
| queue ns_up_work
| ns_up_work:
| zfcp_fc_wka_port_get
| open wka request
| open response
| GSPN FC-GS
| RSPN FC-GS [NPIV-only]
| zfcp_fc_wka_port_put
| (--wka->refcount==0)
| sched delayed wka->work
|
~~~Case (1)~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
zfcp_erp_wait
flush scan_work
| wka->work:
| wka->status=CLOSING
| close wka request
| scan_work:
| zfcp_fc_wka_port_get
| (wka->status==CLOSING)
| wka->status=OPENING
| open wka request
| wait_event
| | close response
| | wka->status=OFFLINE
| | wake_up /*WRONG*/
~~~Case (2)~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| wka->work:
| wka->status=CLOSING
| close wka request
zfcp_erp_wait
flush scan_work
| scan_work:
| zfcp_fc_wka_port_get
| (wka->status==CLOSING)
| wka->status=OPENING
| open wka request
| close response
| wka->status=OFFLINE
| wake_up /*WRONG&NOP*/
| wait_event /*NOP*/
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| (wka->status!=ONLINE)
| return -EIO
| return early
open response
wka->status=ONLINE
wake_up /*NOP*/
So we erroneously end up with no automatic port scan. This is a big problem
when it happens during boot. The timing is influenced by v3.19 commit
18f87a67e6 ("zfcp: auto port scan resiliency").
Fix it by fully mutually excluding zfcp_fc_wka_port_get() and
zfcp_fc_wka_port_offline(). For that to work, we make the latter block
until we got the response for a close WKA port. In order not to penalize
the system workqueue, we move wka_port->work to our own adapter workqueue.
Note that before v2.6.30 commit 828bc1212a ("[SCSI] zfcp: Set WKA-port to
offline on adapter deactivation"), zfcp did block in
zfcp_fc_wka_port_offline() as well, but with a different condition.
While at it, make non-functional cleanups to improve code reading in
zfcp_fc_wka_port_get(). If we cannot send the WKA port open request, don't
rely on the subsequent wait_event condition to immediately let this case
pass without blocking. Also don't want to rely on the additional condition
handling the refcount to be skipped just to finally return with -EIO.
Link: https://lore.kernel.org/r/20220729162529.1620730-1-maier@linux.ibm.com
Fixes: 5ab944f97e ("[SCSI] zfcp: attach and release SAN nameserver port on demand")
Cc: <stable@vger.kernel.org> #v2.6.28+
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ba592fa01 ]
In the function s3fb_set_par(), the value of 'screen_size' is
calculated by the user input. If the user provides the improper value,
the value of 'screen_size' may larger than 'info->screen_size', which
may cause the following bug:
[ 54.083733] BUG: unable to handle page fault for address: ffffc90003000000
[ 54.083742] #PF: supervisor write access in kernel mode
[ 54.083744] #PF: error_code(0x0002) - not-present page
[ 54.083760] RIP: 0010:memset_orig+0x33/0xb0
[ 54.083782] Call Trace:
[ 54.083788] s3fb_set_par+0x1ec6/0x4040
[ 54.083806] fb_set_var+0x604/0xeb0
[ 54.083836] do_fb_ioctl+0x234/0x670
Fix the this by checking the value of 'screen_size' before memset_io().
Fixes: a268422de8 ("fbdev driver for S3 Trio/Virge")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96b550971c ]
In the function arkfb_set_par(), the value of 'screen_size' is
calculated by the user input. If the user provides the improper value,
the value of 'screen_size' may larger than 'info->screen_size', which
may cause the following bug:
[ 659.399066] BUG: unable to handle page fault for address: ffffc90003000000
[ 659.399077] #PF: supervisor write access in kernel mode
[ 659.399079] #PF: error_code(0x0002) - not-present page
[ 659.399094] RIP: 0010:memset_orig+0x33/0xb0
[ 659.399116] Call Trace:
[ 659.399122] arkfb_set_par+0x143f/0x24c0
[ 659.399130] fb_set_var+0x604/0xeb0
[ 659.399161] do_fb_ioctl+0x234/0x670
[ 659.399189] fb_ioctl+0xdd/0x130
Fix the this by checking the value of 'screen_size' before memset_io().
Fixes: 681e14730c ("arkfb: new framebuffer driver for ARK Logic cards")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec0754c602 ]
In the function vt8623fb_set_par(), the value of 'screen_size' is
calculated by the user input. If the user provides the improper value,
the value of 'screen_size' may larger than 'info->screen_size', which
may cause the following bug:
[ 583.339036] BUG: unable to handle page fault for address: ffffc90005000000
[ 583.339049] #PF: supervisor write access in kernel mode
[ 583.339052] #PF: error_code(0x0002) - not-present page
[ 583.339074] RIP: 0010:memset_orig+0x33/0xb0
[ 583.339110] Call Trace:
[ 583.339118] vt8623fb_set_par+0x11cd/0x21e0
[ 583.339146] fb_set_var+0x604/0xeb0
[ 583.339181] do_fb_ioctl+0x234/0x670
[ 583.339209] fb_ioctl+0xdd/0x130
Fix the this by checking the value of 'screen_size' before memset_io().
Fixes: 558b7bd86c ("vt8623fb: new framebuffer driver for VIA VT8623")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de979c8357 ]
With CONFIG_PREEMPTION disabled, arch/x86/entry/thunk_$(BITS).o becomes
an empty object file.
With some old versions of binutils (i.e., 2.35.90.20210113-1ubuntu1) the
GNU assembler doesn't generate a symbol table for empty object files and
objtool fails with the following error when a valid symbol table cannot
be found:
arch/x86/entry/thunk_64.o: warning: objtool: missing symbol table
To prevent this from happening, build thunk_$(BITS).o only if
CONFIG_PREEMPTION is enabled.
BugLink: https://bugs.launchpad.net/bugs/1911359
Fixes: 320100a5ff ("x86/entry: Remove the TRACE_IRQS cruft")
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/Ys/Ke7EWjcX+ZlXO@arighi-desktop
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c58cf40e3 ]
A build with -D_FORTIFY_SOURCE=2 enabled will produce the following warnings:
sysfs.c:63:30: warning: '%s' directive output may be truncated writing up to 255 bytes into a region of size between 0 and 255 [-Wformat-truncation=]
snprintf(filepath, 256, "%s/%s", path, filename);
^~
Bump up the buffer to PATH_MAX which is the limit and account for all of
the possible NUL and separators that could lead to exceeding the
allocated buffer sizes.
Fixes: 94f69966fa ("tools/thermal: Introduce tmon, a tool for thermal subsystem")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f1c4523f7 ]
Since the user can control the arguments of the ioctl() from the user
space, under special arguments that may result in a divide-by-zero bug
in:
drivers/video/fbdev/arkfb.c:784: ark_set_pixclock(info, (hdiv * info->var.pixclock) / hmul);
with hdiv=1, pixclock=1 and hmul=2 you end up with (1*1)/2 = (int) 0.
and then in:
drivers/video/fbdev/arkfb.c:504: rv = dac_set_freq(par->dac, 0, 1000000000 / pixclock);
we'll get a division-by-zero.
The following log can reveal it:
divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:ark_set_pixclock drivers/video/fbdev/arkfb.c:504 [inline]
RIP: 0010:arkfb_set_par+0x10fc/0x24c0 drivers/video/fbdev/arkfb.c:784
Call Trace:
fb_set_var+0x604/0xeb0 drivers/video/fbdev/core/fbmem.c:1034
do_fb_ioctl+0x234/0x670 drivers/video/fbdev/core/fbmem.c:1110
fb_ioctl+0xdd/0x130 drivers/video/fbdev/core/fbmem.c:1189
Fix this by checking the argument of ark_set_pixclock() first.
Fixes: 681e14730c ("arkfb: new framebuffer driver for ARK Logic cards")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 625395c4a0 ]
GCC-12 started triggering a new warning:
arch/x86/mm/numa.c: In function ‘cpumask_of_node’:
arch/x86/mm/numa.c:916:39: warning: the comparison will always evaluate as ‘false’ for the address of ‘node_to_cpumask_map’ will never be NULL [-Waddress]
916 | if (node_to_cpumask_map[node] == NULL) {
| ^~
node_to_cpumask_map is of type cpumask_var_t[].
When CONFIG_CPUMASK_OFFSTACK is set, cpumask_var_t is typedef'd to a
pointer for dynamic allocation, else to an array of one element. The
"wicked game" can be checked on line 700 of include/linux/cpumask.h.
The original code in debug_cpumask_set_cpu() and cpumask_of_node() were
probably written by the original authors with CONFIG_CPUMASK_OFFSTACK=y
(i.e. dynamic allocation) in mind, checking if the cpumask was available
via a direct NULL check.
When CONFIG_CPUMASK_OFFSTACK is not set, GCC gives the above warning
while compiling the kernel.
Fix that by using cpumask_available(), which does the NULL check when
CONFIG_CPUMASK_OFFSTACK is set, otherwise returns true. Use it wherever
such checks are made.
Conditional definitions of cpumask_available() can be found along with
the definition of cpumask_var_t. Check the cpumask.h reference mentioned
above.
Fixes: c032ef60d1 ("cpumask: convert node_to_cpumask_map[] to cpumask_var_t")
Fixes: de2d9445f1 ("x86: Unify node_to_cpumask_map handling between 32 and 64bit")
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20220731160913.632092-1-code@siddh.me
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6e8d40d43 ]
With cgroup v2, the cpuset's cpus_allowed mask can be empty indicating
that the cpuset will just use the effective CPUs of its parent. So
cpuset_can_attach() can call task_can_attach() with an empty mask.
This can lead to cpumask_any_and() returns nr_cpu_ids causing the call
to dl_bw_of() to crash due to percpu value access of an out of bound
CPU value. For example:
[80468.182258] BUG: unable to handle page fault for address: ffffffff8b6648b0
:
[80468.191019] RIP: 0010:dl_cpu_busy+0x30/0x2b0
:
[80468.207946] Call Trace:
[80468.208947] cpuset_can_attach+0xa0/0x140
[80468.209953] cgroup_migrate_execute+0x8c/0x490
[80468.210931] cgroup_update_dfl_csses+0x254/0x270
[80468.211898] cgroup_subtree_control_write+0x322/0x400
[80468.212854] kernfs_fop_write_iter+0x11c/0x1b0
[80468.213777] new_sync_write+0x11f/0x1b0
[80468.214689] vfs_write+0x1eb/0x280
[80468.215592] ksys_write+0x5f/0xe0
[80468.216463] do_syscall_64+0x5c/0x80
[80468.224287] entry_SYSCALL_64_after_hwframe+0x44/0xae
Fix that by using effective_cpus instead. For cgroup v1, effective_cpus
is the same as cpus_allowed. For v2, effective_cpus is the real cpumask
to be used by tasks within the cpuset anyway.
Also update task_can_attach()'s 2nd argument name to cs_effective_cpus to
reflect the change. In addition, a check is added to task_can_attach()
to guard against the possibility that cpumask_any_and() may return a
value >= nr_cpu_ids.
Fixes: 7f51412a41 ("sched/deadline: Fix bandwidth check/update when migrating tasks between exclusive cpusets")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20220803015451.2219567-1-longman@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 772b6539fd ]
Both functions are doing almost the same, that is checking if admission
control is still respected.
With exclusive cpusets, dl_task_can_attach() checks if the destination
cpuset (i.e. its root domain) has enough CPU capacity to accommodate the
task.
dl_cpu_busy() checks if there is enough CPU capacity in the cpuset in
case the CPU is hot-plugged out.
dl_task_can_attach() is used to check if a task can be admitted while
dl_cpu_busy() is used to check if a CPU can be hotplugged out.
Make dl_cpu_busy() able to deal with a task and use it instead of
dl_task_can_attach() in task_can_attach().
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Juri Lelli <juri.lelli@redhat.com>
Link: https://lore.kernel.org/r/20220302183433.333029-4-dietmar.eggemann@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4b39e88b4 ]
The recent change to the PHB numbering logic has a logic error in the
handling of "ibm,opal-phbid".
When an "ibm,opal-phbid" property is present, &prop is written to and
ret is set to zero.
The following call to of_alias_get_id() is skipped because ret == 0.
But then the if (ret >= 0) is true, and the body of that if statement
sets prop = ret which throws away the value that was just read from
"ibm,opal-phbid".
Fix the logic by only doing the ret >= 0 check in the of_alias_get_id()
case.
Fixes: 0fe1e96fef ("powerpc/pci: Prefer PCI domain assignment via DT 'linux,pci-domain' and alias")
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220802105723.1055178-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28f6c37a29 ]
kernel_text_address() treats ftrace_trampoline, kprobe_insn_slot
and bpf_text_address as valid kprobe addresses - which is not ideal.
These text areas are removable and changeable without any notification
to kprobes, and probing on them can trigger unexpected behavior:
https://lkml.org/lkml/2022/7/26/1148
Considering that jump_label and static_call text are already
forbiden to probe, kernel_text_address() should be replaced with
core_kernel_text() and is_module_text_address() to check other text
areas which are unsafe to kprobe.
[ mingo: Rewrote the changelog. ]
Fixes: 5b485629ba ("kprobes, extable: Identify kprobes trampolines as kernel text area")
Fixes: 74451e66d5 ("bpf: make jited programs visible in traces")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20220801033719.228248-1-chenzhongjin@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d518ac7be ]
The perf jvmti agent doesn't create program headers, in this case
fallback on section headers as happened previously.
Committer notes:
To test this, from a public post by Ian:
1) download a Java workload dacapo-9.12-MR1-bach.jar from
https://sourceforge.net/projects/dacapobench/
2) build perf such as "make -C tools/perf O=/tmp/perf NO_LIBBFD=1" it
should detect Java and create /tmp/perf/libperf-jvmti.so
3) run perf with the jvmti agent:
perf record -k 1 java -agentpath:/tmp/perf/libperf-jvmti.so -jar dacapo-9.12-MR1-bach.jar -n 10 fop
4) run perf inject:
perf inject -i perf.data -o perf-injected.data -j
5) run perf report
perf report -i perf-injected.data | grep org.apache.fop
With this patch reverted I see lots of symbols like:
0.00% java jitted-388040-4656.so [.] org.apache.fop.fo.FObj.bind(org.apache.fop.fo.PropertyList)
With the patch (2d86612aac ("perf symbol: Correct address for bss
symbols")) I see lots of:
dso__load_sym_internal: failed to find program header for symbol:
Lorg/apache/fop/fo/FObj;bind(Lorg/apache/fop/fo/PropertyList;)V
st_value: 0x40
Fixes: 2d86612aac ("perf symbol: Correct address for bss symbols")
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20220731164923.691193-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ee236dcaa ]
If the inode has the compress flag, it will fail to use
'chattr -c +m' to remove its compress flag and tag no compress flag.
However, the same command will be successful when executed again,
as shown below:
$ touch foo.txt
$ chattr +c foo.txt
$ chattr -c +m foo.txt
chattr: Invalid argument while setting flags on foo.txt
$ chattr -c +m foo.txt
$ f2fs_io getflags foo.txt
get a flag on foo.txt ret=0, flags=nocompression,inline_data
Fix this by removing some checks in f2fs_setflags_common()
that do not affect the original logic. I go through all the
possible scenarios, and the results are as follows. Bold is
the only thing that has changed.
+---------------+-----------+-----------+----------+
| | file flags |
+ command +-----------+-----------+----------+
| | no flag | compr | nocompr |
+---------------+-----------+-----------+----------+
| chattr +c | compr | compr | -EINVAL |
| chattr -c | no flag | no flag | nocompr |
| chattr +m | nocompr | -EINVAL | nocompr |
| chattr -m | no flag | compr | no flag |
| chattr +c +m | -EINVAL | -EINVAL | -EINVAL |
| chattr +c -m | compr | compr | compr |
| chattr -c +m | nocompr | *nocompr* | nocompr |
| chattr -c -m | no flag | no flag | no flag |
+---------------+-----------+-----------+----------+
Link: https://lore.kernel.org/linux-f2fs-devel/20220621064833.1079383-1-chaoliu719@gmail.com/
Fixes: 4c8ff7095b ("f2fs: support data compression")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Chao Liu <liuchao@coolpad.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9163b947a ]
If there's not enough free sections each of which consistis of large segments,
we can hit no free section for upcoming section allocation. Let's reclaim some
prefree segments by writing checkpoints.
Signed-off-by: Byungki Lee <dominicus79@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 642c096991 ]
So that it can reduce the possibility that file be unpinned forcely by
foreground GC due to .i_gc_failures[GC_FAILURE_PIN] exceeds threshold.
Signed-off-by: Chao Yu <chao.yu@oppo.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fe1e96fef ]
Other Linux architectures use DT property 'linux,pci-domain' for
specifying fixed PCI domain of PCI controller specified in Device-Tree.
And lot of Freescale powerpc boards have defined numbered pci alias in
Device-Tree for every PCIe controller which number specify preferred PCI
domain.
So prefer usage of DT property 'linux,pci-domain' (via function
of_get_pci_domain_nr()) and DT pci alias (via function
of_alias_get_id()) on powerpc architecture for assigning PCI domain to
PCI controller.
Fixes: 63a72284b1 ("powerpc/pci: Assign fixed PHB number based on device-tree properties")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220706102148.5060-2-pali@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eb8fccc24 ]
The second operand of a '&&' operator has no impact on expression
result for cases 400 and 512 in SiS_GetModeID().
Judging by the logic and the names of the variables, in both cases a
typo was made.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rustam Subkhankulov <subkhankulov@ispras.ru>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26c2b7d9fa ]
In clcdfb_of_init_display(), we should call of_node_put() for the
references returned by of_graph_get_next_endpoint() and
of_graph_get_remote_port_parent() which have increased the refcount.
Besides, we should call of_node_put() both in fail path or when
the references are not used anymore.
Fixes: d10715be03 ("video: ARM CLCD: Add DT support")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
