DMA transfer could be completed, but CPU (which handles DMA interrupt)
may get too busy and can't handle the interrupt in a timely manner,
despite of DMA IRQ being raised. In this case the DMA state needs to
synchronized before terminating DMA transfer in order not to miss the
DMA transfer completion.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Boot CPU0 always handle I2C interrupt and under some rare circumstances
(like running KASAN + NFS root) it may stuck in uninterruptible state for
a significant time. In this case we will get timeout if I2C transfer is
running on a sibling CPU, despite of IRQ being raised. In order to handle
this rare condition, the IRQ status needs to be checked after completion
timeout.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The reg in the example "<0x5fc10000 0x1000>, <0x5fc20000 0x800>"
is wrong. The register region of this controller is much smaller,
and there is no other hardware register interleaved. There is no
good reason to split it into two regions.
Just use a single, contiguous register region.
While I am here, I made the 'dma-channels' property mandatory because
otherwise there is no way to determine the number of the channels.
Please note the original binding was merged recently. Since there
is no user yet, this change has no actual impact.
Fixes: b9fb56b6ba ("dt-bindings: dmaengine: Add UniPhier external DMA controller bindings")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200401032150.19767-1-yamada.masahiro@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DMA transfer might finish just after checking the state with
dma_cookie_status, but before the lock is acquired. Not checking
for an empty list in xilinx_dma_tx_status may result in reading
random data or data corruption when desc is written to. This can
be reliably triggered by using dma_sync_wait to wait for DMA
completion.
Signed-off-by: Sebastian von Ohr <vonohr@smaract.com>
Tested-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20200303130518.333-1-vonohr@smaract.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix:
arch/x86/kvm/svm/sev.c: In function ‘sev_pin_memory’:
arch/x86/kvm/svm/sev.c:360:3: error: implicit declaration of function ‘release_pages’;\
did you mean ‘reclaim_pages’? [-Werror=implicit-function-declaration]
360 | release_pages(pages, npinned);
| ^~~~~~~~~~~~~
| reclaim_pages
because svm.c includes pagemap.h but the carved out sev.c needs it too.
Triggered by a randconfig build.
Fixes: eaf78265a4 ("KVM: SVM: Move SEV code to separate file")
Signed-off-by: Borislav Petkov <bp@suse.de>
Message-Id: <20200411160927.27954-1-bp@alien8.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to SDM 26.6.2, it is possible to inject an MTF VM-exit via the
VM-entry interruption-information field regardless of the 'monitor trap
flag' VM-execution control. KVM appropriately copies the VM-entry
interruption-information field from vmcs12 to vmcs02. However, if L1
has not set the 'monitor trap flag' VM-execution control, KVM fails to
reflect the subsequent MTF VM-exit into L1.
Fix this by consulting the VM-entry interruption-information field of
vmcs12 to determine if L1 has injected the MTF VM-exit. If so, reflect
the exit, regardless of the 'monitor trap flag' VM-execution control.
Fixes: 5f3d45e7f2 ("kvm/x86: add support for MONITOR_TRAP_FLAG")
Signed-off-by: Oliver Upton <oupton@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20200414224746.240324-1-oupton@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If PCI_MSI is not set, building fais:
drivers/dma/hisi_dma.c: In function ‘hisi_dma_free_irq_vectors’:
drivers/dma/hisi_dma.c:138:2: error: implicit declaration of function ‘pci_free_irq_vectors’;
did you mean ‘pci_alloc_irq_vectors’? [-Werror=implicit-function-declaration]
pci_free_irq_vectors(data);
^~~~~~~~~~~~~~~~~~~~
Make HISI_DMA depends on PCI_MSI to fix this.
Fixes: e9f08b6525 ("dmaengine: hisilicon: Add Kunpeng DMA engine support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200328114133.17560-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
siw_fastreg_mr() invokes siw_mem_id2obj(), which returns a local reference
of the siw_mem object to "mem" with increased refcnt. When
siw_fastreg_mr() returns, "mem" becomes invalid, so the refcount should be
decreased to keep refcount balanced.
The issue happens in one error path of siw_fastreg_mr(). When "base_mr"
equals to NULL but "mem" is not NULL, the function forgets to decrease the
refcnt increased by siw_mem_id2obj() and causes a refcnt leak.
Reorganize the flow so that the goto unwind can be used as expected.
Fixes: b9be6f18cf ("rdma/siw: transmit path")
Link: https://lore.kernel.org/r/1586939949-69856-1-git-send-email-xiyuyang19@fudan.edu.cn
Reported-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When deciding whether a guest has to be stopped we check whether this
is a private interrupt or not. Unfortunately, there's an off-by-one bug
here, and we fail to recognize a whole range of interrupts as being
global (GICv2 SPIs 32-63).
Fix the condition from > to be >=.
Cc: stable@vger.kernel.org
Fixes: abd7229626 ("KVM: arm/arm64: Simplify active_change_prepare and plug race")
Reported-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
HID_DEVICE_ID_ALPS_1657 PID is too specific, as there are many other
ALPS hardware IDs using this particular touchpad.
Rename the identifier to HID_DEVICE_ID_ALPS_U1_UNICORN_LEGACY in order
to describe reality better.
Fixes: 640e403b1f ("HID: alps: Add AUI1657 device ID")
Reported-by: Xiaojian Cao <xiaojian.cao@cn.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In assembly, many instances of __emit_inst(x) expand to a directive. In
a few places __emit_inst(x) is used as an assembler macro argument. For
example, in arch/arm64/kvm/hyp/entry.S
ALTERNATIVE(nop, SET_PSTATE_PAN(1), ARM64_HAS_PAN, CONFIG_ARM64_PAN)
expands to the following by the C preprocessor:
alternative_insn nop, .inst (0xd500401f | ((0) << 16 | (4) << 5) | ((!!1) << 8)), 4, 1
Both comma and space are separators, with an exception that content
inside a pair of parentheses/quotes is not split, so the clang
integrated assembler splits the arguments to:
nop, .inst, (0xd500401f | ((0) << 16 | (4) << 5) | ((!!1) << 8)), 4, 1
GNU as preprocesses the input with do_scrub_chars(). Its arm64 backend
(along with many other non-x86 backends) sees:
alternative_insn nop,.inst(0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# .inst(...) is parsed as one argument
while its x86 backend sees:
alternative_insn nop,.inst (0xd500401f|((0)<<16|(4)<<5)|((!!1)<<8)),4,1
# The extra space before '(' makes the whole .inst (...) parsed as two arguments
The non-x86 backend's behavior is considered unintentional
(https://sourceware.org/bugzilla/show_bug.cgi?id=25750).
So drop the space separator inside `.inst (...)` to make the clang
integrated assembler work.
Suggested-by: Ilie Halip <ilie.halip@gmail.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/939
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
At the moment, PCM devices for DPCM are only created based on the
dpcm_playback/capture parameters of the DAI link, without considering
if the CPU/FE DAI is actually capable of playback/capture.
Normally the dpcm_playback/capture parameter should match the
capabilities of the CPU DAI. However, there is no way to set that
parameter from the device tree (e.g. with simple-audio-card or
qcom sound cards). dpcm_playback/capture are always both set to 1.
This causes problems when the CPU DAI does only support playback
or capture. Attemting to open that PCM device with an unsupported
stream type then results in a null pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000128
Internal error: Oops: 96000044 [#1] PREEMPT SMP
CPU: 3 PID: 1582 Comm: arecord Not tainted 5.7.0-rc1
pc : invalidate_paths_ep+0x30/0xe0
lr : snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8
Call trace:
invalidate_paths_ep+0x30/0xe0
snd_soc_dapm_dai_get_connected_widgets+0x170/0x1a8
dpcm_path_get+0x38/0xd0
dpcm_fe_dai_open+0x70/0x920
snd_pcm_open_substream+0x564/0x840
snd_pcm_open+0xfc/0x228
snd_pcm_capture_open+0x4c/0x78
snd_open+0xac/0x1a8
...
... because the DAI playback/capture_widget is not set in that case.
We could add checks there to fix the problem (maybe we should
anyway), but much easier is to not expose the device as
playback/capture in the first place. Attemting to use that
device would always fail later anyway.
Add checks for snd_soc_dai_stream_valid() to the DPCM case
to avoid exposing playback/capture if it is not supported.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200415104928.86091-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
As mentioned slightly out of patch context in the code, there
is no reset routine for the chip. On boards where the chip is
supplied by a fixed regulator, it might not even be resetted
during (e.g. watchdog) reboot and can be in any state.
If the device is probed with VAG enabled, the driver's probe
routine will generate a loud pop sound when ANA_POWER is
being programmed. Avoid this by properly disabling just the
VAG bit and waiting the required power down time.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Fabio Estevam <festivem@gmail.com>
Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
David Ahern noticed that there was a bug in the EXPECTED_FD code so
programs did not get detached properly when that parameter was supplied.
This case was not included in the xdp_attach tests; so let's add it to be
sure that such a bug does not sneak back in down.
Fixes: 87854a0b57 ("selftests/bpf: Add tests for attaching XDP programs")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200414145025.182163-2-toke@redhat.com
The 'old_fd' parameter used for atomic replacement of XDP programs is
supposed to be an FD, but was left as a u32 from an earlier iteration of
the patch that added it. It was converted to an int when read, so things
worked correctly even with negative values, but better change the
definition to correctly reflect the intention.
Fixes: bd5ca3ef93 ("libbpf: Add function to set link XDP fd while specifying old program")
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200414145025.182163-1-toke@redhat.com
For some types of BPF programs that utilize expected_attach_type, libbpf won't
set load_attr.expected_attach_type, even if expected_attach_type is known from
section definition. This was done to preserve backwards compatibility with old
kernels that didn't recognize expected_attach_type attribute yet (which was
added in 5e43f899b0 ("bpf: Check attach type at prog load time"). But this
is problematic for some BPF programs that utilize newer features that require
kernel to know specific expected_attach_type (e.g., extended set of return
codes for cgroup_skb/egress programs).
This patch makes libbpf specify expected_attach_type by default, but also
detect support for this field in kernel and not set it during program load.
This allows to have a good metadata for bpf_program
(e.g., bpf_program__get_extected_attach_type()), but still work with old
kernels (for cases where it can work at all).
Additionally, due to expected_attach_type being always set for recognized
program types, bpf_program__attach_cgroup doesn't have to do extra checks to
determine correct attach type, so remove that additional logic.
Also adjust section_names selftest to account for this change.
More detailed discussion can be found in [0].
[0] https://lore.kernel.org/bpf/20200412003604.GA15986@rdna-mbp.dhcp.thefacebook.com/
Fixes: 5cf1e91456 ("bpf: cgroup inet skb programs can return 0 to 3")
Fixes: 5e43f899b0 ("bpf: Check attach type at prog load time")
Reported-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Link: https://lore.kernel.org/bpf/20200414182645.1368174-1-andriin@fb.com
The aarch32_vdso_pages[] array never has entries allocated in the C_VVAR
or C_VDSO slots, and as the array is zero initialized these contain
NULL.
However in __aarch32_alloc_vdso_pages() when
aarch32_alloc_kuser_vdso_page() fails we attempt to free the page whose
struct page is at NULL, which is obviously nonsensical.
This patch removes the erroneous page freeing.
Fixes: 7c1deeeb01 ("arm64: compat: VDSO setup for compat layer")
Cc: <stable@vger.kernel.org> # 5.3.x-
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
All in-tree users have been converted to the new i2c_new_scanned_device
function, so remove this deprecated one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
device_property_read_u32() returns errno or 0, so we should use the
integer variable 'ret' and not the u32 'val' to hold the retval.
Fixes: 0560ad5762 ("i2c: altera: Add Altera I2C Controller driver")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We already set DPM_FLAG_SMART_PREPARE, so we completely skip all
callbacks (other then prepare) where possible, quoting from
dw_i2c_plat_prepare():
/*
* If the ACPI companion device object is present for this device, it
* may be accessed during suspend and resume of other devices via I2C
* operation regions, so tell the PM core and middle layers to avoid
* skipping system suspend/resume callbacks for it in that case.
*/
return !has_acpi_companion(dev);
Also setting the DPM_FLAG_SMART_SUSPEND will cause acpi_subsys_suspend()
to leave the controller runtime-suspended even if dw_i2c_plat_prepare()
returned 0.
Leaving the controller runtime-suspended normally, when the I2C controller
is suspended during the suspend_late phase, is not an issue because
the pm_runtime_get_sync() done by i2c_dw_xfer() will (runtime-)resume it.
But for dw I2C controllers on Bay- and Cherry-Trail devices acpi_lpss.c
leaves the controller alive until the suspend_noirq phase, because it may
be used by the _PS3 ACPI methods of PCI devices and PCI devices are left
powered on until the suspend_noirq phase.
Between the suspend_late and resume_early phases runtime-pm is disabled.
So for any ACPI I2C OPRegion accesses done after the suspend_late phase,
the pm_runtime_get_sync() done by i2c_dw_xfer() is a no-op and the
controller is left runtime-suspended.
i2c_dw_xfer() has a check to catch this condition (rather then waiting
for the I2C transfer to timeout because the controller is suspended).
acpi_subsys_suspend() leaving the controller runtime-suspended in
combination with an ACPI I2C OPRegion access done after the suspend_late
phase triggers this check, leading to the following error being logged
on a Bay Trail based Lenovo Thinkpad 8 tablet:
[ 93.275882] i2c_designware 80860F41:00: Transfer while suspended
[ 93.275993] WARNING: CPU: 0 PID: 412 at drivers/i2c/busses/i2c-designware-master.c:429 i2c_dw_xfer+0x239/0x280
...
[ 93.276252] Workqueue: kacpi_notify acpi_os_execute_deferred
[ 93.276267] RIP: 0010:i2c_dw_xfer+0x239/0x280
...
[ 93.276340] Call Trace:
[ 93.276366] __i2c_transfer+0x121/0x520
[ 93.276379] i2c_transfer+0x4c/0x100
[ 93.276392] i2c_acpi_space_handler+0x219/0x510
[ 93.276408] ? up+0x40/0x60
[ 93.276419] ? i2c_acpi_notify+0x130/0x130
[ 93.276433] acpi_ev_address_space_dispatch+0x1e1/0x252
...
So since on BYT and CHT platforms we want ACPI I2c OPRegion accesses
to work until the suspend_noirq phase, we need the controller to be
runtime-resumed during the suspend phase if it is runtime-suspended
suspended at that time. This means that we must not set the
DPM_FLAG_SMART_SUSPEND on these platforms.
On BYT and CHT we already have a special ACCESS_NO_IRQ_SUSPEND flag
to make sure the controller stays functional until the suspend_noirq
phase. This commit makes the driver not set the DPM_FLAG_SMART_SUSPEND
flag when that flag is set.
Cc: stable@vger.kernel.org
Fixes: b30f2f6556 ("i2c: designware: Set IRQF_NO_SUSPEND flag for all BYT and CHT controllers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Work around this warning:
kernel/sched/cputime.c: In function ‘kcpustat_field’:
kernel/sched/cputime.c:1007:6: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
because GCC can't see that val is used only when err is 0.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200327214334.GF8015@zn.tnic
The "isolcpus=" parameter allows sub-parameters before the cpulist is
specified, and if the parser detects an unknown sub-parameters the whole
parameter will be ignored.
This design is incompatible with itself when new sub-parameters are added.
An older kernel will not recognize the new sub-parameter and will
invalidate the whole parameter so the CPU isolation will not take
effect. It emits a warning:
isolcpus: Error, unknown flag
The better and compatible way is to allow "isolcpus=" to skip unknown
sub-parameters, so that even if new sub-parameters are added an older
kernel will still be able to behave as usual even if with the new
sub-parameter specified on the command line.
Ideally this should have been there when the first sub-parameter for
"isolcpus=" was introduced.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200403223517.406353-1-peterx@redhat.com
CLONE_ARGS_SIZE_VER* macros are defined explicitly and not via
the offsets of the relevant struct clone_args fields, which makes
it rather error-prone, so it probably makes sense to add some
compile-time checks for them (including the one that breaks
on struct clone_args extension as a reminder to add a relevant
size macro and a similar check). Function copy_clone_args_from_user
seems to be a good place for such checks.
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20200412202658.GA31499@asgard.redhat.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Checking that cgroup field value of struct clone_args is less than 0
is useless, as it is defined as unsigned 64-bit integer. Moreover,
it doesn't catch the situations where its higher bits are lost during
the assignment to the cgroup field of the cgroup field of the internal
struct kernel_clone_args (where it is declared as signed 32-bit
integer), so it is still possible to pass garbage there. A check
against INT_MAX solves both these issues.
Fixes: ef2c41cf38 ("clone3: allow spawning processes into cgroups")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20200412202533.GA29554@asgard.redhat.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
A race condition leading to a kernel crash is observed during invocation
of ieee80211_register_hw() on a dragonboard410c device having wcn36xx
driver built as a loadable module along with a wifi manager in user-space
waiting for a wifi device (wlanX) to be active.
Sequence diagram for a particular kernel crash scenario:
user-space ieee80211_register_hw() ieee80211_tasklet_handler()
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
| | |
|<---phy0----wiphy_register() |
|-----iwd if_add---->| |
| |<---IRQ----(RX packet)
| Kernel crash |
| due to unallocated |
| workqueue. |
| | |
| alloc_ordered_workqueue() |
| | |
| Misc wiphy init. |
| | |
| ieee80211_if_add() |
| | |
As evident from above sequence diagram, this race condition isn't specific
to a particular wifi driver but rather the initialization sequence in
ieee80211_register_hw() needs to be fixed. So re-order the initialization
sequence and the updated sequence diagram would look like:
user-space ieee80211_register_hw() ieee80211_tasklet_handler()
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
| | |
| alloc_ordered_workqueue() |
| | |
| Misc wiphy init. |
| | |
|<---phy0----wiphy_register() |
|-----iwd if_add---->| |
| |<---IRQ----(RX packet)
| | |
| ieee80211_if_add() |
| | |
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/1586254255-28713-1-git-send-email-sumit.garg@linaro.org
[Johannes: fix rtnl imbalances]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware driver is optional, but the power driver depends on it,
which needs to be reflected in Kconfig to avoid link errors:
aarch64-linux-ld: drivers/soc/xilinx/zynqmp_power.o: in function `zynqmp_pm_isr':
zynqmp_power.c:(.text+0x284): undefined reference to `zynqmp_pm_invoke_fn'
The firmware driver can probably be allowed for compile-testing as
well, so it's best to drop the dependency on the ZYNQ platform
here and allow building as long as the firmware code is built-in.
Fixes: ab272643d7 ("drivers: soc: xilinx: Add ZynqMP PM driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200408155224.2070880-1-arnd@arndb.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When checking for draining with __req_need_defer(), it tries to match
how many requests were sent before a current one with number of already
completed. Dropped SQEs are included in req->sequence, and they won't
ever appear in CQ. To compensate for that, __req_need_defer() substracts
ctx->cached_sq_dropped.
However, what it should really use is number of SQEs dropped __before__
the current one. In other words, any submitted request shouldn't
shouldn't affect dequeueing from the drain queue of previously submitted
ones.
Instead of saving proper ctx->cached_sq_dropped in each request,
substract from req->sequence it at initialisation, so it includes number
of properly submitted requests.
note: it also changes behaviour of timeouts, but
1. it's already diverge from the description because of using SQ
2. the description is ambiguous regarding dropped SQEs
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
req->timeout.count and req->io->timeout.seq_offset store the same value,
which is sqe->off. Kill the second one
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_timeout() can be executed asynchronously by a worker and without
holding ctx->uring_lock
1. using ctx->cached_sq_head there is racy there
2. it should count events from a moment of timeout's submission, but
not execution
Use req->sequence.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some Google Apex Edge TPU devices have a class code of 0
(PCI_CLASS_NOT_DEFINED). This prevents the PCI core from assigning
resources for the Apex BARs because __dev_sort_resources() ignores
classless devices, host bridges, and IOAPICs.
On x86, firmware typically assigns those resources, so this was not a
problem. But on some architectures, firmware does *not* assign BARs, and
since the PCI core didn't do it either, the Apex device didn't work
correctly:
apex 0000:01:00.0: can't enable device: BAR 0 [mem 0x00000000-0x00003fff 64bit pref] not claimed
apex 0000:01:00.0: error enabling PCI device
f390d08d8b ("staging: gasket: apex: fixup undefined PCI class") added a
quirk to fix the class code, but it was in the apex driver, and if the
driver was built as a module, it was too late to help.
Move the quirk to the PCI core, where it will always run early enough that
the PCI core will assign resources if necessary.
Link: https://lore.kernel.org/r/CAEzXK1r0Er039iERnc2KJ4jn7ySNUOG9H=Ha8TD8XroVqiZjgg@mail.gmail.com
Fixes: f390d08d8b ("staging: gasket: apex: fixup undefined PCI class")
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Debugged-by: Luís Mendes <luis.p.mendes@gmail.com>
Tested-by: Luis Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Todd Poynor <toddpoynor@google.com>
Russell King says:
====================
Fix 88x3310 leaving power save mode
This series fixes a problem with the 88x3310 PHY on Macchiatobin
coming out of powersave mode noticed by Matteo Croce. It seems
that certain PHY firmwares do not properly exit powersave mode,
resulting in a fibre link not coming up.
The solution appears to be to soft-reset the PHY after clearing
the powersave bit.
We add support for reporting the PHY firmware version to the kernel
log, and use it to trigger this new behaviour if we have v0.3.x.x
or more recent firmware on the PHY. This, however, is a guess as
the firmware revision documentation does not mention this issue,
and we know that v0.2.1.0 works without this fix but v0.3.3.0 and
later does not.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Soft-reset the PHY when coming out of low power mode, which seems to
be necessary with firmware versions 0.3.3.0 and 0.3.10.0.
This depends on ("net: marvell10g: report firmware version")
Fixes: c9cc1c815d ("net: phy: marvell10g: place in powersave mode at probe")
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Positive return values are also failures that don't set val,
although this probably can't happen. Fixes gcc 10 warning:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c: In function ‘t4_phy_fw_ver’:
drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:3747:14: warning: ‘val’ may be used uninitialized in this function [-Wmaybe-uninitialized]
3747 | *phy_fw_ver = val;
Fixes: 01b6961410 ("cxgb4: Add PHY firmware support for T420-BT cards")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
