Allow all the RGMII modes to be used. (Not only "rgmii", "rgmii-id"
but "rgmii-txid", "rgmii-rxid")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
mv88e6xxx fixed link fixes
Recent changes for how the MAC is configured broke fixed links, as
used by CPU/DSA ports, and for SFPs when phylink cannot be used. The
first fix is unchanged from v1. The second fix takes a different
solution than v1. If a CPU or DSA port is known to have a PHYLINK
instance, configure the port down before instantiating the PHYLINK, so
it is in the down state as expected by PHYLINK.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA and CPU ports can be configured in two ways. By default, the
driver should configure such ports to there maximum bandwidth. For
most use cases, this is sufficient. When this default is insufficient,
a phylink instance can be bound to such ports, and phylink will
configure the port, e.g. based on fixed-link properties. phylink
assumes the port is initially down. Given that the driver should have
already configured it to its maximum speed, ask the driver to down
the port before instantiating the phylink instance.
Fixes: 30c4a5b0aa ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e6185 is reporting it has detected a PHY, when a port is
connected to an SFP. As a result, the fixed-phy configuration is not
being applied. That then breaks packet transfer, since the port is
reported as being down.
Add additional conditions to check the interface mode, and if it is
fixed always configure the port on link up/down, independent of the
PPU status.
Fixes: 30c4a5b0aa ("net: mv88e6xxx: use resolved link config in mac_link_up()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson says:
====================
ionic: address automated build complaints
Kernel build checks found a couple of things to improve.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an unused initialized value.
Fixes: 7e4d47596b ("ionic: replay filters after fw upgrade")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the appropriate header for using dynamic_hex_dump(), which
seems to be incidentally included in some configurations but
not all.
Fixes: 7e4d47596b ("ionic: replay filters after fw upgrade")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the DATA packet transmission to disable nofrag for UDPv4 on an AF_INET6
socket as well as UDPv6 when trying to transmit fragmentably.
Without this, packets filled to the normal size used by the kernel AFS
client of 1412 bytes be rejected by udp_sendmsg() with EMSGSIZE
immediately. The ->sk_error_report() notification hook is called, but
rxrpc doesn't generate a trace for it.
This is a temporary fix; a more permanent solution needs to involve
changing the size of the packets being filled in accordance with the MTU,
which isn't currently done in AF_RXRPC. The reason for not doing so was
that, barring the last packet in an rx jumbo packet, jumbos can only be
assembled out of 1412-byte packets - and the plan was to construct jumbos
on the fly at transmission time.
Also, there's no point turning on IPV6_MTU_DISCOVER, since IPv6 has to
engage in this anyway since fragmentation is only done by the sender. We
can then condense the switch-statement in rxrpc_send_data_packet().
Fixes: 75b54cb57c ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ9131 will not work with some switches due to workaround for KSZ9031
introduced in commit d2fd719bcb
("net/phy: micrel: Add workaround for bad autoneg").
Use genphy_read_status instead of dedicated ksz9031_read_status.
Fixes: bff5b4b373 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free block_cb memory when asked to be deleted.
Fixes: 978703f425 ("netfilter: flowtable: Add API for registering to flow table events")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Merge an operating performance points (OPP) framework update for
5.7-rc2 from Viresh Kumar:
"This contains a single patch that lets the OPP core to be used by
several IO drivers without making a lot of changes in them for the
case where the same driver may be used by a platform with an OPP
table or a clock node on another one. I am looking to get this into
5.7 release itself, which will enable other users (in multiple
frameworks) to get merged without waiting for the dependency to get
resolved."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Manage empty OPP tables with clk handle
phy-rockchip-inno-usb2.txt was converted to yaml.
Fix the corresponding reference.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Changeset 32ced09d79 ("dt-bindings: serial: Convert slave-device bindings to json-schema")
moved a binding to json and updated the links.
Yet, one link was not changed, due to a merge conflict.
Update this one too.
Fixes: 32ced09d79 ("dt-bindings: serial: Convert slave-device bindings to json-schema")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
This file was removed, and another file was added instead of
it, on two separate commits.
Splitting a single logical change (doc conversion) on two
patches is a bad thing, as it makes harder to discover what
crap happened.
Anyway, this patch fixes the broken reference, making it
pointing to the new location of the file.
Fixes: 922003733d ("dt-bindings: phy: Remove Cadence MHDP PHY dt binding")
Fixes: c6d8eef38b7f ("dt-bindings: phy: Add Cadence MHDP PHY bindings in YAML format.")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
'loongson,parent_int_map' is an array, but the schema is defining a
matrix resulting in the follow warnings:
Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.example.dt.yaml:
interrupt-controller@3ff01400: loongson,parent_int_map:0: [4043309055] is too short
Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.example.dt.yaml:
interrupt-controller@3ff01400: loongson,parent_int_map:1: [251658240] is too short
Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.example.dt.yaml:
interrupt-controller@3ff01400: loongson,parent_int_map:2: [0] is too short
Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.example.dt.yaml:
interrupt-controller@3ff01400: loongson,parent_int_map:3: [0] is too short
The correct way to define an array is a list in 'items' and/or a size
defined by 'minItems' and 'maxItems'.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
A recent update to dtc and changes to the default warnings introduced
some new warnings in the DT binding examples:
Documentation/devicetree/bindings/arm/sunxi/allwinner,sun4i-a10-mbus.example.dts:23.13-61:
Warning (dma_ranges_format): /example-0/dram-controller@1c01000:dma-ranges: "dma-ranges" property has invalid length (12 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 1)
Documentation/devicetree/bindings/hwmon/adi,axi-fan-control.example.dts:17.22-28.11:
Warning (unit_address_vs_reg): /example-0/fpga-axi@0: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/memory-controllers/nvidia,tegra186-mc.example.dts:34.13-54:
Warning (dma_ranges_format): /example-0/memory-controller@2c00000:dma-ranges: "dma-ranges" property has invalid length (24 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 2)
Documentation/devicetree/bindings/mfd/st,stpmic1.example.dts:19.15-79.11:
Warning (unit_address_vs_reg): /example-0/i2c@0: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/net/qcom,ipq8064-mdio.example.dts:28.23-31.15:
Warning (unit_address_vs_reg): /example-0/mdio@37000000/switch@10: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/rng/brcm,bcm2835.example.dts:17.5-21.11:
Warning (unit_address_vs_reg): /example-0/rng: node has a reg or ranges property, but no unit name
Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.example.dts:20.20-43.11:
Warning (unit_address_vs_reg): /example-0/soc@0: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/usb/ingenic,musb.example.dts:18.28-21.11:
Warning (unit_address_vs_reg): /example-0/usb-phy@0: node has a unit name, but no reg or ranges property
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "Nuno Sá" <nuno.sa@analog.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-hwmon@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-spi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The DT example needs #address-cells and #size-cells for I2C bus or
validity checker will generate warnings. Add these properties in
BD71837 and BD71847 binding examples.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The following warnings are seen with 'make dt_binding_check':
Documentation/devicetree/bindings/clock/arm,syscon-icst.example.dts:17.16-24.11: Warning (unit_address_vs_reg): /example-0/clock@00: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/clock/arm,syscon-icst.example.dts:17.16-24.11: Warning (unit_address_format): /example-0/clock@00: unit name should not have leading 0s
Fix them by removing the unneeded clock unit name.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The following warnings are seen with 'make dt_binding_check':
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.example.dts:19.22-30.11: Warning (unit_address_vs_reg): /example-0/i2c@00000000: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.example.dts:19.22-30.11: Warning (unit_address_format): /example-0/i2c@00000000: unit name should not have leading 0s
Fix it by removing the unneeded i2c unit name.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The following warning is seen with 'make dt_binding_check':
Documentation/devicetree/bindings/iio/dac/adi,ad5770r.yaml: $id: relative path/filename doesn't match actual path or filename
Fix it by removing the "bindings" directory from the file path.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The compatible string in the example misses the vendor information.
Pass the "adi" vendor to fix it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Before the hibernation patchset (e.g. f53335e328), in a Generation-2
Linux VM on Hyper-V, the user can run "echo freeze > /sys/power/state" to
freeze the system, i.e. Suspend-to-Idle. The user can press the keyboard
or move the mouse to wake up the VM.
With the hibernation patchset, Linux VM on Hyper-V can hibernate to disk,
but Suspend-to-Idle is broken: when the synthetic keyboard/mouse are
suspended, there is no way to wake up the VM.
Fix the issue by not suspending and resuming the vmbus devices upon
Suspend-to-Idle.
Fixes: f53335e328 ("Drivers: hv: vmbus: Suspend/resume the vmbus itself for hibernation")
Cc: stable@vger.kernel.org
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1586663435-36243-1-git-send-email-decui@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Kalle Valo says:
====================
wireless-drivers fixes for v5.7
First set of fixes for v5.6. Fixes for a crash and for two compiler
warnings.
brcmfmac
* fix a crash related to monitor interface
ath11k
* fix compiler warnings without CONFIG_THERMAL
rtw88
* fix compiler warnings related to suspend and resume functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit mentioned in the Fixes tag reuses the local prog variable
when looking up an expected_fd. The variable is not reset when fd < 0
causing a detach with the expected_fd set to actually call
dev_xdp_install for the existing program. The end result is that the
detach does not happen.
Fixes: 92234c8f15 ("xdp: Support specifying expected existing program when attaching XDP")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200412133204.43847-1-dsahern@kernel.org
In commit 65c9362859 ("bpftool: Add struct_ops support") a new
type of command named struct_ops has been added. This command requires
a kernel with CONFIG_DEBUG_INFO_BTF=y set and for retrieving BTF info
in bpftool, the helper get_btf_vmlinux() is used.
When running this command on kernel without BTF debug info, this will
lead to 'btf_vmlinux' variable being an invalid(error) pointer. And by
this, btf_free() causes a segfault when executing 'bpftool struct_ops'.
This commit adds pointer validation with IS_ERR not to free invalid
pointer, and this will fix the segfault issue.
Fixes: 65c9362859 ("bpftool: Add struct_ops support")
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200410020612.2930667-1-danieltimlee@gmail.com
Test that frozen and mmap()'ed BPF map can't be mprotect()'ed as writable or
executable memory. Also validate that "downgrading" from writable to read-only
doesn't screw up internal writable count accounting for the purposes of map
freezing.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200410202613.3679837-2-andriin@fb.com
VM_MAYWRITE flag during initial memory mapping determines if already mmap()'ed
pages can be later remapped as writable ones through mprotect() call. To
prevent user application to rewrite contents of memory-mapped as read-only and
subsequently frozen BPF map, remove VM_MAYWRITE flag completely on initially
read-only mapping.
Alternatively, we could treat any memory-mapping on unfrozen map as writable
and bump writecnt instead. But there is little legitimate reason to map
BPF map as read-only and then re-mmap() it as writable through mprotect(),
instead of just mmap()'ing it as read/write from the very beginning.
Also, at the suggestion of Jann Horn, drop unnecessary refcounting in mmap
operations. We can just rely on VMA holding reference to BPF map's file
properly.
Fixes: fc9702273e ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/bpf/20200410202613.3679837-1-andriin@fb.com
This patch fixes an incorrect check in how immediate memory offsets are
computed for BPF_DW on arm.
For BPF_LDX/ST/STX + BPF_DW, the 32-bit arm JIT breaks down an 8-byte
access into two separate 4-byte accesses using off+0 and off+4. If off
fits in imm12, the JIT emits a ldr/str instruction with the immediate
and avoids the use of a temporary register. While the current check off
<= 0xfff ensures that the first immediate off+0 doesn't overflow imm12,
it's not sufficient for the second immediate off+4, which may cause the
second access of BPF_DW to read/write the wrong address.
This patch fixes the problem by changing the check to
off <= 0xfff - 4 for BPF_DW, ensuring off+4 will never overflow.
A side effect of simplifying the check is that it now allows using
negative immediate offsets in ldr/str. This means that small negative
offsets can also avoid the use of a temporary register.
This patch introduces no new failures in test_verifier or test_bpf.c.
Fixes: c5eae69257 ("ARM: net: bpf: improve 64-bit store implementation")
Fixes: ec19e02b34 ("ARM: net: bpf: fix LDX instructions")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200409221752.28448-1-luke.r.nels@gmail.com
Pull hyperv fixes from Wei Liu:
- a series from Tianyu Lan to fix crash reporting on Hyper-V
- three miscellaneous cleanup patches
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/Hyper-V: Report crash data in die() when panic_on_oops is set
x86/Hyper-V: Report crash register data when sysctl_record_panic_msg is not set
x86/Hyper-V: Report crash register data or kmsg before running crash kernel
x86/Hyper-V: Trigger crash enlightenment only once during system crash.
x86/Hyper-V: Free hv_panic_page when fail to register kmsg dump
x86/Hyper-V: Unload vmbus channel in hv panic callback
x86: hyperv: report value of misc_features
hv_debugfs: Make hv_debug_root static
hv: hyperv_vmbus.h: Replace zero-length array with flexible-array member
Pull btrfs fixes from David Sterba:
"We have a few regressions and one fix for stable:
- revert fsync optimization
- fix lost i_size update
- fix a space accounting leak
- build fix, add back definition of a deprecated ioctl flag
- fix search condition for old roots in relocation"
* tag 'for-5.7-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: re-instantiate the removed BTRFS_SUBVOL_CREATE_ASYNC definition
btrfs: fix reclaim counter leak of space_info objects
btrfs: make full fsyncs always operate on the entire file again
btrfs: fix lost i_size update after cloning inline extent
btrfs: check commit root generation in should_ignore_root
The cm_reset_to_idle() call before formatting event changed the CM_ID
state from IB_CM_REQ_RCVD to be IB_CM_IDLE. It caused to wrong value of
CM_REJ_MESSAGE_REJECTED field.
The result of that was that rdma_reject() calls in the passive side didn't
generate RDMA_CM_EVENT_REJECTED event in the active side.
Fixes: 81ddb41f87 ("RDMA/cm: Allow ib_send_cm_rej() to be done under lock")
Link: https://lore.kernel.org/r/20200406173242.1465911-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Pull AFS fixes from David Howells:
- Fix the decoding of fetched file status records so that the xdr
pointer is advanced under all circumstances.
- Fix the decoding of a fetched file status record that indicates an
inline abort (ie. an error) so that it sets the flag saying the
decoder stored the abort code.
- Fix the decoding of the result of the rename operation so that it
doesn't skip the decoding of the second fetched file status (ie. that
of the dest dir) in the case that the source and dest dirs were the
same as this causes the xdr pointer not to be advanced, leading to
incorrect decoding of subsequent parts of the reply.
- Fix the dump of a bad YFSFetchStatus record to dump the full length.
- Fix a race between local editing of directory contents and accessing
the dir for reading or d_revalidate by using the same lock in both.
- Fix afs_d_revalidate() to not accidentally reverse the version on a
dentry when it's meant to be bringing it forward.
* tag 'afs-fixes-20200413' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix afs_d_validate() to set the right directory version
afs: Fix race between post-modification dir edit and readdir/d_revalidate
afs: Fix length of dump of bad YFSFetchStatus record
afs: Fix rename operation status delivery
afs: Fix decoding of inline abort codes from version 1 status records
afs: Fix missing XDR advance in xdr_decode_{AFS,YFS}FSFetchStatus()
Currently the null check for wqe is incorrect and lets a null wqe
be passed to set_64bit_val and this indexes into the null pointer
causing a null pointer dereference. Fix this by fixing the null
pointer check to return an error if wqe is null.
Link: https://lore.kernel.org/r/20200401224921.405279-1-colin.king@canonical.com
Addresses-Coverity: ("dereference after a null check")
Fixes: 4b34e23f4e ("i40iw: Report correct firmware version")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The system reboot failed as some IP blocks enter power gate before perform
hw resource destory. Meanwhile use unify interface to set device CGPG to ungate
state can simplify the amdgpu poweroff or reset ungate guard.
Fixes: 487eca11a3 ("drm/amdgpu: fix gfx hang during suspend with video playback (v2)")
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Tested-by: Mengbing Wang <Mengbing.Wang@amd.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Commit 52120e8c7a ("dt-bindings: display: fix panel warnings") removed
the dsi unit name, but missed to remove the 'reg' property, which causes
the following 'make dt_binding_check' warning:
Documentation/devicetree/bindings/display/panel/xinpeng,xpp055c272.example.dts:17.5-29.11: Warning (unit_address_vs_reg): /example-0/dsi: node has a reg or ranges property, but no unit name
Fix it by removing the unneeded 'reg' property.
Fixes: 52120e8c7a ("dt-bindings: display: fix panel warnings")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200328183641.11226-2-festevam@gmail.com
(cherry picked from commit b1e44754af)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Commit 52120e8c7a ("dt-bindings: display: fix panel warnings") removed
the dsi unit name, but missed to remove the 'reg' property, which causes
the following 'make dt_binding_check' warning:
Documentation/devicetree/bindings/display/panel/leadtek,ltk500hd1829.example.dts:17.5-29.11: Warning (unit_address_vs_reg): /example-0/dsi: node has a reg or ranges property, but no unit name
Fix it by removing the unneeded 'reg' property.
Fixes: 52120e8c7a ("dt-bindings: display: fix panel warnings")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200328183641.11226-1-festevam@gmail.com
(cherry picked from commit dcde9c02f8)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
After successfully running the IPC msgque test once, subsequent runs
result in a test failure:
$ sudo ./run_kselftest.sh
TAP version 13
1..1
# selftests: ipc: msgque
# Failed to get stats for IPC queue with id 0
# Failed to dump queue: -22
# Bail out!
# # Pass 0 Fail 0 Xfail 0 Xpass 0 Skip 0 Error 0
not ok 1 selftests: ipc: msgque # exit=1
The dump_queue() function loops through the possible message queue index
values using calls to msgctl(kern_id, MSG_STAT, ...) where kern_id
represents the index value. The first time the test is ran, the initial
index value of 0 is valid and the test is able to complete. The index
value of 0 is not valid in subsequent test runs and the loop attempts to
try index values of 1, 2, 3, and so on until a valid index value is
found that corresponds to the message queue created earlier in the test.
The msgctl() syscall returns -1 and sets errno to EINVAL when invalid
index values are used. The test failure is caused by incorrectly
comparing errno to -EINVAL when cycling through possible index values.
Fix invalid test failures on subsequent runs of the msgque test by
correctly comparing errno values to a non-negated EINVAL.
Fixes: 3a665531a3 ("selftests: IPC message queue copy feature test")
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
ftrace-direct.tc and kprobe-direct.tc require CONFIG_SAMPLE_FTRACE_DIRECT=m
so add it to config file which is used by merge_config.sh.
Signed-off-by: Xiao Yang <yangx.jy@cn.fujitsu.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
glibc 2.31 calls clock_nanosleep when its nanosleep function is used. So
the restart_syscall fails after that. In order to deal with it, we trace
clock_nanosleep and nanosleep. Then we check for either.
This works just fine on systems with both glibc 2.30 and glibc 2.31,
whereas it failed before on a system with glibc 2.31.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
While running seccomp_bpf, kill_after_ptrace() gets stuck if we run it
via /usr/bin/timeout (that is the default), until the timeout expires.
This is because /usr/bin/timeout is preventing to properly deliver
signals to ptrace'd children (SIGSYS in this case).
This problem can be easily reproduced by running:
$ sudo make TARGETS=seccomp kselftest
...
# [ RUN ] TRACE_syscall.skip_a#
not ok 1 selftests: seccomp: seccomp_bpf # TIMEOUT
The test is hanging at this point until the timeout expires and then it
reports the timeout error.
Prevent this problem by passing --foreground to /usr/bin/timeout,
allowing to properly deliver signals to children processes.
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
