commit a6139b6271 upstream.
This patch corrects the error case in association path by returning
-1. Earlier "media_connected" used to remain on in this error case
causing failure for further association attempts.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Fixes: b887664d88 ('mwifiex: channel switch handling for station')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8134233e8d upstream.
If the call to acpi_get_object_info() fails then "info" hasn't been
initialized. In that situation, we already know that "version" should
be XGENE_AHCI_V1 so we don't actually need to dereference "info".
Fixes: c9802a4be6 ('ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da6ccaaa79 upstream.
Make the "Attempted send on closed socket" error messages generated in
nbd_request_handler() ratelimited.
When the nbd socket is shutdown, the nbd_request_handler() function emits
an error message for every request remaining in its queue. If the queue
is large, this will spam a large amount of messages to the log. There's
no need for a separate error message for each request, so this patch
ratelimits it.
In the specific case this was found, the system was virtual and the error
messages were logged to the serial port, which overwhelmed it.
Fixes: 4d48a542b4 ("nbd: fix I/O hang on disconnected nbds")
Signed-off-by: Dan Streetman <dan.streetman@canonical.com>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f719e3754e upstream.
Jiri Bohac is reporting for a problem where the attempt
to reschedule existing connection to another real server
needs proper redirect for the conntrack used by the IPVS
connection. For example, when IPVS connection is created
to NAT-ed real server we alter the reply direction of
conntrack. If we later decide to select different real
server we can not alter again the conntrack. And if we
expire the old connection, the new connection is left
without conntrack.
So, the only way to redirect both the IPVS connection and
the Netfilter's conntrack is to drop the SYN packet that
hits existing connection, to wait for the next jiffie
to expire the old connection and its conntrack and to rely
on client's retransmission to create new connection as
usually.
Jiri Bohac provided a fix that drops all SYNs on rescheduling,
I extended his patch to do such drops only for connections
that use conntrack. Here is the original report from Jiri Bohac:
Since commit dc7b3eb900 ("ipvs: Fix reuse connection if real server
is dead"), new connections to dead servers are redistributed
immediately to new servers. The old connection is expired using
ip_vs_conn_expire_now() which sets the connection timer to expire
immediately.
However, before the timer callback, ip_vs_conn_expire(), is run
to clean the connection's conntrack entry, the new redistributed
connection may already be established and its conntrack removed
instead.
Fix this by dropping the first packet of the new connection
instead, like we do when the destination server is not available.
The timer will have deleted the old conntrack entry long before
the first packet of the new connection is retransmitted.
Fixes: dc7b3eb900 ("ipvs: Fix reuse connection if real server is dead")
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7617a24f83 upstream.
The IPVS SIP persistence engine is not able to parse the SIP header
"Call-ID" when such header is inserted in the first positions of
the SIP message.
When IPVS is configured with "--pe sip" option, like for example:
ipvsadm -A -u 1.2.3.4:5060 -s rr --pe sip -p 120 -o
some particular messages (see below for details) do not create entries
in the connection template table, which can be listed with:
ipvsadm -Lcn --persistent-conn
Problematic SIP messages are SIP responses having "Call-ID" header
positioned just after message first line:
SIP/2.0 200 OK
[Call-ID header here]
[rest of the headers]
When "Call-ID" header is positioned down (after a few other headers)
it is correctly recognized.
This is due to the data offset used in get_callid function call inside
ip_vs_pe_sip.c file: since dptr already points to the start of the
SIP message, the value of dataoff should be initially 0.
Otherwise the header is searched starting from some bytes after the
first character of the SIP message.
Fixes: 758ff03387 ("IPVS: sip persistence engine")
Signed-off-by: Marco Angaroni <marcoangaroni@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f20efba41 upstream.
ip_vs_fill_iph_skb_off() may not find an IP header, and gcc has
determined that ip_vs_sip_fill_param() then incorrectly accesses
the protocol fields:
net/netfilter/ipvs/ip_vs_pe_sip.c: In function 'ip_vs_sip_fill_param':
net/netfilter/ipvs/ip_vs_pe_sip.c:76:5: error: 'iph.protocol' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (iph.protocol != IPPROTO_UDP)
^
net/netfilter/ipvs/ip_vs_pe_sip.c:81:10: error: 'iph.len' may be used uninitialized in this function [-Werror=maybe-uninitialized]
dataoff = iph.len + sizeof(struct udphdr);
^
This adds a check for the ip_vs_fill_iph_skb_off() return code
before looking at the ip header data returned from it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b0e010c527 ("ipvs: replace ip_vs_fill_ip4hdr with ip_vs_fill_iph_skb_off")
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4924e9244 upstream.
The info->status[] array has 3 elements. We are using size
MAX77843_MUIC_IRQ_NUM (16) instead of MAX77843_MUIC_STATUS_NUM (3) as
intended.
Fixes: 135d9f7d13 ('extcon: max77843: Clear IRQ bits state before request IRQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[cw00.choi: Modify the patch title]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 042d4460b5 upstream.
The newly added STM code uses SRCU, but does not ensure that
this code is part of the kernel:
drivers/built-in.o: In function `stm_source_link_show':
include/linux/srcu.h:221: undefined reference to `__srcu_read_lock'
include/linux/srcu.h:238: undefined reference to `__srcu_read_unlock'
drivers/built-in.o: In function `stm_source_link_drop':
include/linux/srcu.h:221: undefined reference to `__srcu_read_lock'
include/linux/srcu.h:238: undefined reference to `__srcu_read_unlock'
This adds a Kconfig 'select' statement like all the other SRCU using
drivers have.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7bd1d4093c ("stm class: Introduce an abstraction for System Trace Module devices")
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3deb9438d3 upstream.
gcc-6 found a dubious indentation in the megasas_mgmt_fw_ioctl
function:
drivers/scsi/megaraid/megaraid_sas_base.c: In function 'megasas_mgmt_fw_ioctl':
drivers/scsi/megaraid/megaraid_sas_base.c:6658:4: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
kbuff_arr[i] = NULL;
^~~~~~~~~
drivers/scsi/megaraid/megaraid_sas_base.c:6653:3: note: ...this 'if' clause, but it is not
if (kbuff_arr[i])
^~
The code is actually correct, as there is no downside in clearing a NULL
pointer again.
This clarifies the code and avoids the warning by adding extra curly
braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 90dc9d98f0 ("megaraid_sas : MFI MPT linked list corruption fix")
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ab1e8126 upstream.
sunrpc_cache_pipe_upcall() can detect a race if CACHE_PENDING is no longer
set. In this case it aborts the queuing of the upcall.
However it has already taken a new counted reference on "h" and
doesn't "put" it, even though it frees the data structure holding the reference.
So let's delay the "cache_get" until we know we need it.
Fixes: f9e1aedc6c ("sunrpc/cache: remove races with queuing an upcall.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b4eb9fe7 upstream.
As the Dan report the smatch check the thermal driver warning:
drivers/thermal/rockchip_thermal.c:551 rockchip_configure_from_dt()
warn: impossible condition '(thermal->tshut_temp > ((~0 >> 1))) =>
(s32min-s32max > s32max)'
Although The shut_temp read from DT is u32,the temperature is currently
represented as int not long in the thermal driver.
Let's change to make shut_temp instead of the thermal->tshut_temp for
the condition.
Fixes: commit 437df2172e
("thermal: rockchip: consistently use int for temperatures")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b87b70c53 upstream.
Prior to 3.13 make allmodconfig KCONFIG_ALLCONFIG=/dev/null used
to be equivalent to make allmodconfig; these days it hardwires MODULES to n.
In fact, any KCONFIG_ALLCONFIG that doesn't set MODULES explicitly is
treated as if it set it to n.
Regression had been introduced by commit cfa98f ("kconfig: do not
override symbols already set"); what happens is that conf_read_simple()
does sym_calc_value(modules_sym) on exit, which leaves SYMBOL_VALID set and
has conf_set_all_new_symbols() skip modules_sym.
It's pretty easy to fix - simply move that call of sym_calc_value()
into the callers, except for the ones in KCONFIG_ALLCONFIG handling.
Objections?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes: cfa98f2e0a ("kconfig: do not override symbols already set")
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81422e672f upstream.
According to Documentation/power/devices.txt
The driver should not use device_set_wakeup_enable() which is the policy
for user to decide.
Using device_init_wakeup() to initialize dev->power.should_wakeup and
dev->power.can_wakeup on driver initialization.
And use device_may_wakeup() on suspend to decide if WoL function should
be enabled on NIC.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33b96d2c95 upstream.
Currently we have an incorrect behaviour when multiple devices
are present under the weim node. For example:
&weim {
...
status = "okay";
sram@0,0 {
...
status = "okay";
};
mram@0,0 {
...
status = "disabled";
};
};
In this case only the 'sram' device should be probed and not 'mram'.
However what happens currently is that the status variable is ignored,
causing the 'sram' device to be disabled and 'mram' to be enabled.
Change the weim_parse_dt() function to use
for_each_available_child_of_node()so that the devices marked with
'status = disabled' are not probed.
Suggested-by: Wolfgang Netbal <wolfgang.netbal@sigmatek.at>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07c6b2d01d upstream.
Since the switch from mmp_pdma to pxa_dma driver for pxa architectures,
the pxa_dma requires 2 arguments, namely the requestor line and the
requested priority.
Fix the only left device node which was still passing only one argument,
making the pxa3xx-nand driver misbehave in a device-tree configuration,
ie. failing all data transfers.
Fixes: c943646d1f ("ARM: dts: pxa: add dma engine node to pxa3xx-nand")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3a7f31eb7 upstream.
The Armada 375 has the same SATA IP as Armada 370 and Armada XP, which
requires the PHY speed to be set in the LP_PHY_CTL register for SATA
hotplug to work.
Therefore, this commit updates the compatible string used to describe
the SATA IP in Armada 375 from marvell,orion-sata to
marvell,armada-370-sata.
Fixes: 4de5908509 ("ARM: mvebu: add Device Tree description of the Armada 375 SoC")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc7eb9d589 upstream.
We cannot select a symbol that has disabled dependencies, so
we get a warning if we ever enable EXYNOS_THERMAL without
also turning on THERMAL_OF:
warning: (ARCH_EXYNOS) selects EXYNOS_THERMAL which has unmet direct dependencies (THERMAL && (ARCH_EXYNOS || COMPILE_TEST) && THERMAL_OF)
This adds another 'select' in the platform code to avoid that
case. Alternatively, we could decide to not select EXYNOS_THERMAL
here and instead make it a user option.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f87e6bd3f7 ("thermal: exynos: Add the dependency of CONFIG_THERMAL_OF instead of CONFIG_OF")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef2b1d777d upstream.
The atlas7 clock controller driver registers a reset controller
for itself, which causes a link error when the subsystem is
disabled:
drivers/built-in.o: In function `atlas7_clk_init':
drivers/clk/sirf/clk-atlas7.c:1681: undefined reference to `reset_controller_register'
As the clk driver does not have a Kconfig symbol for itself
but it always built-in when the platform is enabled, we have
to ensure that the reset controller subsystem is also built-in
in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Fixes: 301c5d2940 ("clk: sirf: add CSR atlas7 clk and reset support")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98f4222150 upstream.
Based on CPU type choose generic omap3 or omap3430 specific cpuidle
parameters. Parameters for omap3430 were measured on Nokia N900 device and
added by commit 5a1b1d3a9e ("OMAP3: RX-51: Pass cpu idle parameters")
which were later removed by commit 231900afba ("ARM: OMAP3: cpuidle -
remove rx51 cpuidle parameters table") due to huge code complexity.
This patch brings cpuidle parameters for omap3430 devices again, but uses
simple condition based on CPU type.
Fixes: 231900afba ("ARM: OMAP3: cpuidle - remove rx51 cpuidle
parameters table")
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 011278485e upstream.
When doing delayed allocation, update of on-disk inode size is postponed
until IO submission time. However hole punch or zero range fallocate
calls can end up discarding the tail page cache page and thus on-disk
inode size would never be properly updated.
Make sure the on-disk inode size is updated before truncating page
cache.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32ebffd3bb upstream.
Current code implementing FALLOC_FL_COLLAPSE_RANGE and
FALLOC_FL_INSERT_RANGE is prone to races with buffered writes and page
faults. If buffered write or write via mmap manages to squeeze between
filemap_write_and_wait_range() and truncate_pagecache() in the fallocate
implementations, the written data is simply discarded by
truncate_pagecache() although it should have been shifted.
Fix the problem by moving filemap_write_and_wait_range() call inside
i_mutex and i_mmap_sem. That way we are protected against races with
both buffered writes and page faults.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17048e8a08 upstream.
Currently ext4_alloc_file_blocks() was handling protection against
unlocked DIO. However we now need to sometimes call it under i_mmap_sem
and sometimes not and DIO protection ranks above it (although strictly
speaking this cannot currently create any deadlocks). Also
ext4_zero_range() was actually getting & releasing unlocked DIO
protection twice in some cases. Luckily it didn't introduce any real bug
but it was a land mine waiting to be stepped on. So move DIO protection
out from ext4_alloc_file_blocks() into the two callsites.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea3d7209ca upstream.
Currently, page faults and hole punching are completely unsynchronized.
This can result in page fault faulting in a page into a range that we
are punching after truncate_pagecache_range() has been called and thus
we can end up with a page mapped to disk blocks that will be shortly
freed. Filesystem corruption will shortly follow. Note that the same
race is avoided for truncate by checking page fault offset against
i_size but there isn't similar mechanism available for punching holes.
Fix the problem by creating new rw semaphore i_mmap_sem in inode and
grab it for writing over truncate, hole punching, and other functions
removing blocks from extent tree and for read over page faults. We
cannot easily use i_data_sem for this since that ranks below transaction
start and we need something ranking above it so that it can be held over
the whole truncate / hole punching operation. Also remove various
workarounds we had in the code to reduce race window when page fault
could have created pages with stale mapping information.
Signed-off-by: Jan Kara <jack@suse.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20c07a5bf0 upstream.
Since commit 807f16d4db ("mtd: core: set some defaults
when dev.parent is set"), it's now legal for drivers
to call nand_scan and nand_scan_ident without setting
mtd.owner.
Drop the check and while at it remove the BUG() abuse.
Fixes: 807f16d4db ("mtd: core: set some defaults when dev.parent is set")
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Brian: editorial note - while commit 807f16d4db wasn't explicitly
broken, some follow-up commits in the v4.4 release broke a few
drivers, since they would hit this BUG() if they used nand_scan()
and were built as modules]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d267aefc54 upstream.
The BRCMNAND controller revision 7.1 is almost 100% compatible with the
previous v6.0 register offset layout, except for the Correctable Error
Reporting Threshold registers. Fix this by adding another table with the
correct offsets for CORR_THRESHOLD and CORR_THRESHOLD_EXT.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b5394a3cc upstream.
This patch remove the micron_quad_enable() function which force the Quad
SPI mode. However, once this mode is enabled, the Micron memory expect ALL
commands to use the SPI 4-4-4 protocol. Hence a failure does occur when
calling spi_nor_wait_till_ready() right after the update of the Enhanced
Volatile Configuration Register (EVCR) in the micron_quad_enable() as
the SPI controller driver is not aware about the protocol change.
Since there is almost no performance increase using Fast Read 4-4-4
commands instead of Fast Read 1-1-4 commands, we rather keep on using the
Extended SPI mode than enabling the Quad SPI mode.
Let's take the example of the pretty standard use of 8 dummy cycles during
Fast Read operations on 64KB erase sectors:
Fast Read 1-1-4 requires 8 cycles for the command, then 24 cycles for the
3byte address followed by 8 dummy clock cycles and finally 65536*2 cycles
for the read data; so 131112 clock cycles.
On the other hand the Fast Read 4-4-4 would require 2 cycles for the
command, then 6 cycles for the 3byte address followed by 8 dummy clock
cycles and finally 65536*2 cycles for the read data. So 131088 clock
cycles. The theorical bandwidth increase is 0.0%.
Now using Fast Read operations on 512byte pages:
Fast Read 1-1-4 needs 8+24+8+(512*2) = 1064 clock cycles whereas Fast
Read 4-4-4 would requires 2+6+8+(512*2) = 1040 clock cycles. Hence the
theorical bandwidth increase is 2.3%.
Consecutive reads for non sequential pages is not a relevant use case so
The Quad SPI mode is not worth it.
mtd_speedtest seems to confirm these figures.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 548cd3ab54 ("mtd: spi-nor: Add quad I/O support for Micron SPI NOR")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff1cab374a upstream.
The BSP team noticed that there is spin/mutex lock issue on sh-sci when
CPUFREQ is used. The issue is that the notifier function may call
mutex_lock() while the spinlock is held, which can lead to a BUG().
This may happen if CPUFREQ is changed while another CPU calls
clk_get_rate().
Taking the spinlock was added to the notifier function in commit
e552de2413 ("sh-sci: add platform device private data"), to
protect the list of serial ports against modification during traversal.
At that time the Common Clock Framework didn't exist yet, and
clk_get_rate() just returned clk->rate without taking a mutex.
Note that since commit d535a2305f ("serial: sh-sci: Require a
device per port mapping."), there's no longer a list of serial ports to
traverse, and taking the spinlock became superfluous.
To fix the issue, just remove the cpufreq notifier:
1. The notifier doesn't work correctly: all it does is update stored
clock rates; it does not update the divider in the hardware.
The divider will only be updated when calling sci_set_termios().
I believe this was broken back in 2004, when the old
drivers/char/sh-sci.c driver (where the notifier did update the
divider) was replaced by drivers/serial/sh-sci.c (where the
notifier just updated port->uartclk).
Cfr. full-history-linux commits 6f8deaef2e9675d9 ("[PATCH] sh: port
sh-sci driver to the new API") and 3f73fe878dc9210a ("[PATCH]
Remove old sh-sci driver").
2. On modern SoCs, the sh-sci parent clock rate is no longer related
to the CPU clock rate anyway, so using a cpufreq notifier is
futile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e1021f2b6 upstream.
ext4_reserve_inode_write() in ext4_mark_inode_dirty() could fail on
error (e.g. EIO) and iloc.bh can be NULL in this case. But the error is
ignored in the following "if" condition and ext4_expand_extra_isize()
might be called with NULL iloc.bh set, which triggers NULL pointer
dereference.
This is uncovered by commit 8b4953e13f ("ext4: reserve code points for
the project quota feature"), which enlarges the ext4_inode size, and
run the following script on new kernel but with old mke2fs:
#/bin/bash
mnt=/mnt/ext4
devname=ext4-error
dev=/dev/mapper/$devname
fsimg=/home/fs.img
trap cleanup 0 1 2 3 9 15
cleanup()
{
umount $mnt >/dev/null 2>&1
dmsetup remove $devname
losetup -d $backend_dev
rm -f $fsimg
exit 0
}
rm -f $fsimg
fallocate -l 1g $fsimg
backend_dev=`losetup -f --show $fsimg`
devsize=`blockdev --getsz $backend_dev`
good_tab="0 $devsize linear $backend_dev 0"
error_tab="0 $devsize error $backend_dev 0"
dmsetup create $devname --table "$good_tab"
mkfs -t ext4 $dev
mount -t ext4 -o errors=continue,strictatime $dev $mnt
dmsetup load $devname --table "$error_tab" && dmsetup resume $devname
echo 3 > /proc/sys/vm/drop_caches
ls -l $mnt
exit 0
[ Patch changed to simplify the function a tiny bit. -- Ted ]
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a55e566376 upstream.
We were dropping the reference we possibly held but not obtaining one
for the new maps, which we will drop at perf_evlist__delete(), fix it.
This was caught by Steven Noonan in some of the machines which would
produce this output when caught by glibc debug mechanisms:
$ sudo perf test 21
21: Test object code reading :***
Error in `perf': corrupted double-linked list: 0x00000000023ffcd0 ***
======= Backtrace: =========
/usr/lib/libc.so.6(+0x72055)[0x7f25be0f3055]
/usr/lib/libc.so.6(+0x779b6)[0x7f25be0f89b6]
/usr/lib/libc.so.6(+0x7a0ed)[0x7f25be0fb0ed]
/usr/lib/libc.so.6(__libc_calloc+0xba)[0x7f25be0fceda]
perf(parse_events_lex_init_extra+0x38)[0x4cfff8]
perf(parse_events+0x55)[0x4a0615]
perf(perf_evlist__config+0xcf)[0x4eeb2f]
perf[0x479f82]
perf(test__code_reading+0x1e)[0x47ad4e]
perf(cmd_test+0x5dd)[0x46452d]
perf[0x47f4e3]
perf(main+0x603)[0x42c723]
/usr/lib/libc.so.6(__libc_start_main+0xf0)[0x7f25be0a1610]
perf(_start+0x29)[0x42c859]
Further investigation using valgrind led to the reference count imbalance fixed
in this patch.
Reported-and-Tested-by: Steven Noonan <steven@uplinklabs.net>
Report-Link: http://lkml.kernel.org/r/CAKbGBLjC2Dx5vshxyGmQkcD+VwiAQLbHoXA9i7kvRB2-2opHZQ@mail.gmail.com
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: f30a79b012 ("perf tools: Add reference counting for cpu_map object")
Link: http://lkml.kernel.org/n/tip-j0u1bdhr47sa511sgg76kb8h@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb166ba1d7 upstream.
The regmap_irq_get_virq() can return 0 or -EINVAL in error conditions
but driver checked only for value of 0.
This could lead to a cast of -EINVAL to an unsigned int used as a
interrupt number for devm_request_threaded_irq(). Although this is not
yet fatal (devm_request_threaded_irq() will just fail with -EINVAL) but
might be a misleading when diagnosing errors.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 6f1c1e71d9 ("mfd: max77686: Convert to use regmap_irq")
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a25f4a95ec upstream.
drivers/rtc/rtc-vr41xx.c:229: warning: ‘vr41xx_rtc_alarm_irq_enable’ defined but not used
Apparently the conversion to alarm_irq_enable forgot to wire up the
callback.
Fixes: 16380c153a ("RTC: Convert rtc drivers to use the alarm_irq_enable method")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit beda5fc1ff upstream.
Commit 30e7a65b3f (PM / Domains: Ensure subdomain is not in use
before removing) added a test to ensure that a subdomain is not a
master to another subdomain or if any devices are using the subdomain
before removing. This change incorrectly used the "slave_links" list to
determine if the subdomain is a master to another subdomain, where it
should have been using the "master_links" list instead. The
"slave_links" list will never be empty for a subdomain and so a
subdomain can never be removed. Fix this by testing if the
"master_links" list is empty instead.
Fixes: 30e7a65b3f (PM / Domains: Ensure subdomain is not in use before removing)
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c88c395f4a upstream.
We kept u_volt_min/max initialized to 0, when only the target voltage is
present in DT, instead of the target/min/max triplet.
This didn't go well with the regulator framework, as on few calls the
min voltage was set to target and max was set to 0 and so resulted in a
kernel crash like below:
kernel BUG at ../drivers/regulator/core.c:216!
[<c0684af4>] (regulator_check_voltage) from [<c06857ac>] (regulator_set_voltage_unlocked+0x58/0x230)
[<c06857ac>] (regulator_set_voltage_unlocked) from [<c06859ac>] (regulator_set_voltage+0x28/0x54)
[<c06859ac>] (regulator_set_voltage) from [<c0775b28>] (_set_opp_voltage+0x30/0x98)
[<c0775b28>] (_set_opp_voltage) from [<c0776630>] (dev_pm_opp_set_rate+0xf0/0x28c)
[<c0776630>] (dev_pm_opp_set_rate) from [<c096f784>] (__cpufreq_driver_target+0x184/0x2b4)
[<c096f784>] (__cpufreq_driver_target) from [<c0973760>] (dbs_check_cpu+0x1b0/0x1f4)
[<c0973760>] (dbs_check_cpu) from [<c0973f30>] (cpufreq_governor_dbs+0x324/0x5c4)
[<c0973f30>] (cpufreq_governor_dbs) from [<c0970958>] (__cpufreq_governor+0xe4/0x1ec)
[<c0970958>] (__cpufreq_governor) from [<c09711e0>] (cpufreq_init_policy+0x64/0x8c)
[<c09711e0>] (cpufreq_init_policy) from [<c09718cc>] (cpufreq_online+0x2fc/0x708)
[<c09718cc>] (cpufreq_online) from [<c0765ff0>] (subsys_interface_register+0x94/0xd8)
[<c0765ff0>] (subsys_interface_register) from [<c0970530>] (cpufreq_register_driver+0x14c/0x19c)
[<c0970530>] (cpufreq_register_driver) from [<c09746dc>] (dt_cpufreq_probe+0x70/0xec)
[<c09746dc>] (dt_cpufreq_probe) from [<c076907c>] (platform_drv_probe+0x4c/0xb0)
[<c076907c>] (platform_drv_probe) from [<c07678e0>] (driver_probe_device+0x214/0x2c0)
[<c07678e0>] (driver_probe_device) from [<c0767a18>] (__driver_attach+0x8c/0x90)
[<c0767a18>] (__driver_attach) from [<c0765c2c>] (bus_for_each_dev+0x68/0x9c)
[<c0765c2c>] (bus_for_each_dev) from [<c0766d78>] (bus_add_driver+0x1a0/0x218)
[<c0766d78>] (bus_add_driver) from [<c076810c>] (driver_register+0x78/0xf8)
[<c076810c>] (driver_register) from [<c0301d74>] (do_one_initcall+0x90/0x1d8)
[<c0301d74>] (do_one_initcall) from [<c1100e14>] (kernel_init_freeable+0x15c/0x1fc)
[<c1100e14>] (kernel_init_freeable) from [<c0b27a0c>] (kernel_init+0x8/0xf0)
[<c0b27a0c>] (kernel_init) from [<c0307d78>] (ret_from_fork+0x14/0x3c)
Code: e1550004 baffffeb e3a00000 e8bd8070 (e7f001f2)
Fix that by initializing u_volt_min/max to the target voltage in such cases.
Reported-and-tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 274659029c (PM / OPP: Add support to parse "operating-points-v2" bindings)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b64dbf849 upstream.
Signed integer overflow is undefined. Also I added a check for
"(offset < 0)" in scif_unregister() because that makes it match the
other conditions and because I didn't want to subtract a negative.
Fixes: ba612aa8b4 ('misc: mic: SCIF memory registration and unregistration')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50e6315dba upstream.
Commit 985087dbcb 'misc: add support for bmp18x chips to the bmp085
driver' changed the BMP085 config symbol to a boolean. I see no
reason why the shared code cannot be built as a module, so change it
back to tristate.
Fixes: 985087dbcb ("misc: add support for bmp18x chips to the bmp085 driver")
Cc: Eric Andersson <eric.andersson@unixphere.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ee0cb5fb5 upstream.
The limbs are integers in the host endianness, so we can't simply
iterate over the individual bytes. The current code happens to work on
little-endian, because the order of the limbs in the MPI array is the
same as the order of the bytes in each limb, but it breaks on
big-endian.
Fixes: 0f74fbf77d ("MPI: Fix mpi_read_buffer")
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
