My mainline commit c48a7c44a1d0 ("docs: kernel_feat.py: fix potential
command injection") contains a bug which can manifests like this when
building the documentation:
Sphinx parallel build error:
UnboundLocalError: local variable 'fname' referenced before assignment
make[2]: *** [Documentation/Makefile:102: htmldocs] Error 2
However, this only appears when there exists a '.. kernel-feat::'
directive that points to a non-existent file, which isn't the case in
mainline.
When this commit was backported to stable 6.6, it didn't change
Documentation/arch/ia64/features.rst since ia64 was removed in 6.7 in
commit cf8e8658100d ("arch: Remove Itanium (IA-64) architecture"). This
lead to the build failure seen above -- but only in stable kernels.
This patch fixes the backport and should only be applied to kernels where
Documentation/arch/ia64/features.rst exists and commit c48a7c44a1d0 has
also been applied.
A second patch will follow to fix kernel_feat.py in mainline so that it
doesn't error out when the '.. kernel-feat::' directive points to a
nonexistent file.
Link: https://lore.kernel.org/all/ZbkfGst991YHqJHK@fedora64.linuxtx.org/
Fixes: e961f8c696 ("docs: kernel_feat.py: fix potential command injection") # stable 6.6.15
Reported-by: Justin Forbes <jforbes@fedoraproject.org>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04c3024560d3a14acd18d0a51a1d0a89d29b7eb5 upstream.
AMD does not have the requirement for a synchronization barrier when
acccessing a certain group of MSRs. Do not incur that unnecessary
penalty there.
There will be a CPUID bit which explicitly states that a MFENCE is not
needed. Once that bit is added to the APM, this will be extended with
it.
While at it, move to processor.h to avoid include hell. Untangling that
file properly is a matter for another day.
Some notes on the performance aspect of why this is relevant, courtesy
of Kishon VijayAbraham <Kishon.VijayAbraham@amd.com>:
On a AMD Zen4 system with 96 cores, a modified ipi-bench[1] on a VM
shows x2AVIC IPI rate is 3% to 4% lower than AVIC IPI rate. The
ipi-bench is modified so that the IPIs are sent between two vCPUs in the
same CCX. This also requires to pin the vCPU to a physical core to
prevent any latencies. This simulates the use case of pinning vCPUs to
the thread of a single CCX to avoid interrupt IPI latency.
In order to avoid run-to-run variance (for both x2AVIC and AVIC), the
below configurations are done:
1) Disable Power States in BIOS (to prevent the system from going to
lower power state)
2) Run the system at fixed frequency 2500MHz (to prevent the system
from increasing the frequency when the load is more)
With the above configuration:
*) Performance measured using ipi-bench for AVIC:
Average Latency: 1124.98ns [Time to send IPI from one vCPU to another vCPU]
Cumulative throughput: 42.6759M/s [Total number of IPIs sent in a second from
48 vCPUs simultaneously]
*) Performance measured using ipi-bench for x2AVIC:
Average Latency: 1172.42ns [Time to send IPI from one vCPU to another vCPU]
Cumulative throughput: 40.9432M/s [Total number of IPIs sent in a second from
48 vCPUs simultaneously]
From above, x2AVIC latency is ~4% more than AVIC. However, the expectation is
x2AVIC performance to be better or equivalent to AVIC. Upon analyzing
the perf captures, it is observed significant time is spent in
weak_wrmsr_fence() invoked by x2apic_send_IPI().
With the fix to skip weak_wrmsr_fence()
*) Performance measured using ipi-bench for x2AVIC:
Average Latency: 1117.44ns [Time to send IPI from one vCPU to another vCPU]
Cumulative throughput: 42.9608M/s [Total number of IPIs sent in a second from
48 vCPUs simultaneously]
Comparing the performance of x2AVIC with and without the fix, it can be seen
the performance improves by ~4%.
Performance captured using an unmodified ipi-bench using the 'mesh-ipi' option
with and without weak_wrmsr_fence() on a Zen4 system also showed significant
performance improvement without weak_wrmsr_fence(). The 'mesh-ipi' option ignores
CCX or CCD and just picks random vCPU.
Average throughput (10 iterations) with weak_wrmsr_fence(),
Cumulative throughput: 4933374 IPI/s
Average throughput (10 iterations) without weak_wrmsr_fence(),
Cumulative throughput: 6355156 IPI/s
[1] https://github.com/bytedance/kvm-utils/tree/master/microbenchmark/ipi-bench
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230622095212.20940-1-bp@alien8.de
Signed-off-by: Kishon Vijay Abraham I <kvijayab@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd504bcfec41a503b32054da5472904b404341a4 upstream.
The kvmalloc function fails with a warning if the size is larger than
INT_MAX. The warning was triggered by a syscall testing robot.
In order to avoid the warning, this commit limits the number of targets to
1048576 and the size of the parameter area to 1073741824.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bc09b397cbf1221f8a8aacb1152650c9195b02b upstream.
According to a syzbot report, end_buffer_async_write(), which handles the
completion of block device writes, may detect abnormal condition of the
buffer async_write flag and cause a BUG_ON failure when using nilfs2.
Nilfs2 itself does not use end_buffer_async_write(). But, the async_write
flag is now used as a marker by commit 7f42ec3941 ("nilfs2: fix issue
with race condition of competition between segments for dirty blocks") as
a means of resolving double list insertion of dirty blocks in
nilfs_lookup_dirty_data_buffers() and nilfs_lookup_node_buffers() and the
resulting crash.
This modification is safe as long as it is used for file data and b-tree
node blocks where the page caches are independent. However, it was
irrelevant and redundant to also introduce async_write for segment summary
and super root blocks that share buffers with the backing device. This
led to the possibility that the BUG_ON check in end_buffer_async_write
would fail as described above, if independent writebacks of the backing
device occurred in parallel.
The use of async_write for segment summary buffers has already been
removed in a previous change.
Fix this issue by removing the manipulation of the async_write flag for
the remaining super root block buffer.
Link: https://lkml.kernel.org/r/20240203161645.4992-1-konishi.ryusuke@gmail.com
Fixes: 7f42ec3941 ("nilfs2: fix issue with race condition of competition between segments for dirty blocks")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+5c04210f7c7f897c1e7f@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/00000000000019a97c05fd42f8c8@google.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8f1e0d791b5281f3a38620bc7c57763dc551be15 upstream.
Similar to the existing "ports" node name, coresight device tree bindings
have added "in-ports" and "out-ports" as standard node names for a
collection of ports.
Add support for these name to of_graph_get_port_parent() so that
remote-endpoint parsing can find the correct parent node for these
coresight ports too.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20240207011803.2637531-4-saravanak@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 944d5fe50f3f03daacfea16300e656a1691c4a23 upstream.
On some systems, sys_membarrier can be very expensive, causing overall
slowdowns for everything. So put a lock on the path in order to
serialize the accesses to prevent the ability for this to be called at
too high of a frequency and saturate the machine.
Reviewed-and-tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Borislav Petkov <bp@alien8.de>
Fixes: 22e4ebb975 ("membarrier: Provide expedited private command")
Fixes: c5f58bd58f ("membarrier: Provide GLOBAL_EXPEDITED command")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ad55cecf22f05f1c884adf63cc09d3c3e609ebf upstream.
The .compat section is a dummy PE section that contains the address of
the 32-bit entrypoint of the 64-bit kernel image if it is bootable from
32-bit firmware (i.e., CONFIG_EFI_MIXED=y)
This section is only 8 bytes in size and is only referenced from the
loader, and so it is placed at the end of the memory view of the image,
to avoid the need for padding it to 4k, which is required for sections
appearing in the middle of the image.
Unfortunately, this violates the PE/COFF spec, and even if most EFI
loaders will work correctly (including the Tianocore reference
implementation), PE loaders do exist that reject such images, on the
basis that both the file and memory views of the file contents should be
described by the section headers in a monotonically increasing manner
without leaving any gaps.
So reorganize the sections to avoid this issue. This results in a slight
padding overhead (< 4k) which can be avoided if desired by disabling
CONFIG_EFI_MIXED (which is only needed in rare cases these days)
Fixes: 3e3eabe26dc8 ("x86/boot: Increase section and file alignment to 4k/512")
Reported-by: Mike Beaton <mjsbeaton@gmail.com>
Link: https://lkml.kernel.org/r/CAHzAAWQ6srV6LVNdmfbJhOwhBw5ZzxxZZ07aHt9oKkfYAdvuQQ%40mail.gmail.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e3eabe26dc88692d34cf76ca0e0dd331481cc15 upstream.
Align x86 with other EFI architectures, and increase the section
alignment to the EFI page size (4k), so that firmware is able to honour
the section permission attributes and map code read-only and data
non-executable.
There are a number of requirements that have to be taken into account:
- the sign tools get cranky when there are gaps between sections in the
file view of the image
- the virtual offset of each section must be aligned to the image's
section alignment
- the file offset *and size* of each section must be aligned to the
image's file alignment
- the image size must be aligned to the section alignment
- each section's virtual offset must be greater than or equal to the
size of the headers.
In order to meet all these requirements, while avoiding the need for
lots of padding to accommodate the .compat section, the latter is placed
at an arbitrary offset towards the end of the image, but aligned to the
minimum file alignment (512 bytes). The space before the .text section
is therefore distributed between the PE header, the .setup section and
the .compat section, leaving no gaps in the file coverage, making the
signing tools happy.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230915171623.655440-18-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34951f3c28bdf6481d949a20413b2ce7693687b2 upstream.
Describe the code and data of the decompressor binary using separate
.text and .data PE/COFF sections, so that we will be able to map them
using restricted permissions once we increase the section and file
alignment sufficiently. This avoids the need for memory mappings that
are writable and executable at the same time, which is something that
is best avoided for security reasons.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230915171623.655440-17-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efa089e63b56bdc5eca754b995cb039dd7a5457e upstream.
Now that the size of the setup block is visible to the assembler, it is
possible to populate the PE/COFF header fields from the asm code
directly, instead of poking the values into the binary using the build
tool. This will make it easier to reorganize the section layout without
having to tweak the build tool in lockstep.
This change has no impact on the resulting bzImage binary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230915171623.655440-15-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeb92067f6ae994b541d7f9752fe54ed3d108bcc upstream.
Tweak the linker script so that the value of _edata represents the
decompressor binary's file size rounded up to the appropriate alignment.
This removes the need to calculate it in the build tool, and will make
it easier to refer to the file size from the header directly in
subsequent changes to the PE header layout.
While adding _edata to the sed regex that parses the compressed
vmlinux's symbol list, tweak the regex a bit for conciseness.
This change has no impact on the resulting bzImage binary when
configured with CONFIG_EFI_STUB=y.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230915171623.655440-14-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 093ab258e3fb1d1d3afdfd4a69403d44ce90e360 upstream.
The setup block contains the real mode startup code that is used when
booting from a legacy BIOS, along with the boot_params/setup_data that
is used by legacy x86 bootloaders to pass the command line and initial
ramdisk parameters, among other things.
The setup block also contains the PE/COFF header of the entire combined
image, which includes the compressed kernel image, the decompressor and
the EFI stub.
This PE header describes the layout of the executable image in memory,
and currently, the fact that the setup block precedes it makes it rather
fiddly to get the right values into the right place in the final image.
Let's make things a bit easier by defining the setup_size in the linker
script so it can be referenced from the asm code directly, rather than
having to rely on the build tool to calculate it. For the time being,
add 64 bytes of fixed padding for the .reloc and .compat sections - this
will be removed in a subsequent patch after the PE/COFF header has been
reorganized.
This change has no impact on the resulting bzImage binary when
configured with CONFIG_EFI_MIXED=y.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230915171623.655440-13-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac956345f99dda3d68f4ae6cf7b494105e54780 upstream.
The offsets of the EFI handover entrypoints are available to the
assembler when constructing the header, so there is no need to set them
from the build tool afterwards.
This change has no impact on the resulting bzImage binary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230915171623.655440-12-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e765c02dcbfc2a8a4527c621a84b9502f6b9bd2 upstream.
Instead of parsing zoffset.h and poking the kernel_info offset value
into the header from the build tool, just grab the value directly in the
asm file that describes this header.
This change has no impact on the resulting bzImage binary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230915171623.655440-11-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b618d31f112bea3d2daea19190d63e567f32a4db upstream.
The x86 boot image generation tool assign a default value to startup_64
and subsequently parses the actual value from zoffset.h but it never
actually uses the value anywhere. So remove this code.
This change has no impact on the resulting bzImage binary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-25-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7448e8e5d15a3c4df649bf6d6d460f78396f7e1e upstream.
The root device defaults to 0,0 and is no longer configurable at build
time [0], so there is no need for the build tool to ever write to this
field.
[0] 079f85e624 ("x86, build: Do not set the root_dev field in bzImage")
This change has no impact on the resulting bzImage binary.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-23-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8eace5b3555606e684739bef5bcdfcfe68235257 upstream.
Now that the EFI stub decompresses the kernel and hands over to the
decompressed image directly, there is no longer a need to provide a
decompression buffer as part of the .BSS allocation of the PE/COFF
image. It also means the PE/COFF image can be loaded anywhere in memory,
and setting the preferred image base is unnecessary. So drop the
handling of this from the header and from the build tool.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-22-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 768171d7ebbce005210e1cf8456f043304805c15 upstream.
Ancient (pre-2003) x86 kernels could boot from a floppy disk straight from
the BIOS, using a small real mode boot stub at the start of the image
where the BIOS would expect the boot record (or boot block) to appear.
Due to its limitations (kernel size < 1 MiB, no support for IDE, USB or
El Torito floppy emulation), this support was dropped, and a Linux aware
bootloader is now always required to boot the kernel from a legacy BIOS.
To smoothen this transition, the boot stub was not removed entirely, but
replaced with one that just prints an error message telling the user to
install a bootloader.
As it is unlikely that anyone doing direct floppy boot with such an
ancient kernel is going to upgrade to v6.5+ and expect that this boot
method still works, printing this message is kind of pointless, and so
it should be possible to remove the logic that emits it.
Let's free up this space so it can be used to expand the PE header in a
subsequent patch.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Link: https://lore.kernel.org/r/20230912090051.4014114-21-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e50262229faad0c7b8c54477cd1c883f31cc4a7 upstream.
The native EFI entrypoint does not take a struct boot_params from the
loader, but instead, it constructs one from scratch, using the setup
header data placed at the start of the image.
This setup header is placed in a way that permits legacy loaders to
manipulate the contents (i.e., to pass the kernel command line or the
address and size of an initial ramdisk), but EFI boot does not use it in
that way - it only copies the contents that were placed there at build
time, but EFI loaders will not (and should not) manipulate the setup
header to configure the boot. (Commit 63bf28ceb3 "efi: x86: Wipe
setup_data on pure EFI boot" deals with some of the fallout of using
setup_data in a way that breaks EFI boot.)
Given that none of the non-zero values that are copied from the setup
header into the EFI stub's struct boot_params are relevant to the boot
now that the EFI stub no longer enters via the legacy decompressor, the
copy can be omitted altogether.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230912090051.4014114-19-ardb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ea9a7c5fe4149f165f0e3b624fe08df02b6c301 upstream.
A recent change to check_for_locks() changed it to take ->flc_lock while
holding ->fi_lock. This creates a lock inversion (reported by lockdep)
because there is a case where ->fi_lock is taken while holding
->flc_lock.
->flc_lock is held across ->fl_lmops callbacks, and
nfsd_break_deleg_cb() is one of those and does take ->fi_lock. However
it doesn't need to.
Prior to v4.17-rc1~110^2~22 ("nfsd: create a separate lease for each
delegation") nfsd_break_deleg_cb() would walk the ->fi_delegations list
and so needed the lock. Since then it doesn't walk the list and doesn't
need the lock.
Two actions are performed under the lock. One is to call
nfsd_break_one_deleg which calls nfsd4_run_cb(). These doesn't act on
the nfs4_file at all, so don't need the lock.
The other is to set ->fi_had_conflict which is in the nfs4_file.
This field is only ever set here (except when initialised to false)
so there is no possible problem will multiple threads racing when
setting it.
The field is tested twice in nfs4_set_delegation(). The first test does
not hold a lock and is documented as an opportunistic optimisation, so
it doesn't impose any need to hold ->fi_lock while setting
->fi_had_conflict.
The second test in nfs4_set_delegation() *is* make under ->fi_lock, so
removing the locking when ->fi_had_conflict is set could make a change.
The change could only be interesting if ->fi_had_conflict tested as
false even though nfsd_break_one_deleg() ran before ->fi_lock was
unlocked. i.e. while hash_delegation_locked() was running.
As hash_delegation_lock() doesn't interact in any way with nfs4_run_cb()
there can be no importance to this interaction.
So this patch removes the locking from nfsd_break_one_deleg() and moves
the final test on ->fi_had_conflict out of the locked region to make it
clear that locking isn't important to the test. It is still tested
*after* vfs_setlease() has succeeded. This might be significant and as
vfs_setlease() takes ->flc_lock, and nfsd_break_one_deleg() is called
under ->flc_lock this "after" is a true ordering provided by a spinlock.
Fixes: edcf9725150e ("nfsd: fix RELEASE_LOCKOWNER")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43aa6f97c2d03a52c1ddb86768575fc84344bdbb upstream.
The eventfs inode had pointers to dentries (and child dentries) without
actually holding a refcount on said pointer. That is fundamentally
broken, and while eventfs tried to then maintain coherence with dentries
going away by hooking into the '.d_iput' callback, that doesn't actually
work since it's not ordered wrt lookups.
There were two reasonms why eventfs tried to keep a pointer to a dentry:
- the creation of a 'events' directory would actually have a stable
dentry pointer that it created with tracefs_start_creating().
And it needed that dentry when tearing it all down again in
eventfs_remove_events_dir().
This use is actually ok, because the special top-level events
directory dentries are actually stable, not just a temporary cache of
the eventfs data structures.
- the 'eventfs_inode' (aka ei) needs to stay around as long as there
are dentries that refer to it.
It then used these dentry pointers as a replacement for doing
reference counting: it would try to make sure that there was only
ever one dentry associated with an event_inode, and keep a child
dentry array around to see which dentries might still refer to the
parent ei.
This gets rid of the invalid dentry pointer use, and renames the one
valid case to a different name to make it clear that it's not just any
random dentry.
The magic child dentry array that is kind of a "reverse reference list"
is simply replaced by having child dentries take a ref to the ei. As
does the directory dentries. That makes the broken use case go away.
Link: https://lore.kernel.org/linux-trace-kernel/202401291043.e62e89dc-oliver.sang@intel.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240131185513.280463000@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Ajay Kaher <ajay.kaher@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: c1504e5102 ("eventfs: Implement eventfs dir creation functions")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dce06e98c70a7fcbb4bca7d90faf40522e65c58 upstream.
In order for the dentries to stay up-to-date with the eventfs changes,
just add a 'd_revalidate' function that checks the 'is_freed' bit.
Also, clean up the dentry release to actually use d_release() rather
than the slightly odd d_iput() function. We don't care about the inode,
all we want to do is to get rid of the refcount to the eventfs data
added by dentry->d_fsdata.
It would probably be cleaner to make eventfs its own filesystem, or at
least set its own dentry ops when looking up eventfs files. But as it
is, only eventfs dentries use d_fsdata, so we don't really need to split
these things up by use.
Another thing that might be worth doing is to make all eventfs lookups
mark their dentries as not worth caching. We could do that with
d_delete(), but the DCACHE_DONTCACHE flag would likely be even better.
As it is, the dentries are all freeable, but they only tend to get freed
at memory pressure rather than more proactively. But that's a separate
issue.
Link: https://lore.kernel.org/linux-trace-kernel/202401291043.e62e89dc-oliver.sang@intel.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240131185513.124644253@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Ajay Kaher <ajay.kaher@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: c1504e5102 ("eventfs: Implement eventfs dir creation functions")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 99c001cb617df409dac275a059d6c3f187a2da7a upstream.
The eventfs_find_events() code tries to walk up the tree to find the
event directory that a dentry belongs to, in order to then find the
eventfs inode that is associated with that event directory.
However, it uses an odd combination of walking the dentry parent,
looking up the eventfs inode associated with that, and then looking up
the dentry from there. Repeat.
But the code shouldn't have back-pointers to dentries in the first
place, and it should just walk the dentry parenthood chain directly.
Similarly, 'set_top_events_ownership()' looks up the dentry from the
eventfs inode, but the only reason it wants a dentry is to look up the
superblock in order to look up the root dentry.
But it already has the real filesystem inode, which has that same
superblock pointer. So just pass in the superblock pointer using the
information that's already there, instead of looking up extraneous data
that is irrelevant.
Link: https://lore.kernel.org/linux-trace-kernel/202401291043.e62e89dc-oliver.sang@intel.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240131185512.638645365@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Ajay Kaher <ajay.kaher@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: c1504e5102 ("eventfs: Implement eventfs dir creation functions")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 834bf76add3e6168038150f162cbccf1fd492a67 upstream.
The eventfs inodes and directories are allocated when referenced. But this
leaves the issue of keeping consistent inode numbers and the number is
only saved in the inode structure itself. When the inode is no longer
referenced, it can be freed. When the file that the inode was representing
is referenced again, the inode is once again created, but the inode number
needs to be the same as it was before.
Just making the inode numbers the same for all files is fine, but that
does not work with directories. The find command will check for loops via
the inode number and having the same inode number for directories triggers:
# find /sys/kernel/tracing
find: File system loop detected;
'/sys/kernel/debug/tracing/events/initcall/initcall_finish' is part of the same file system loop as
'/sys/kernel/debug/tracing/events/initcall'.
[..]
Linus pointed out that the eventfs_inode structure ends with a single
32bit int, and on 64 bit machines, there's likely a 4 byte hole due to
alignment. We can use this hole to store the inode number for the
eventfs_inode. All directories in eventfs are represented by an
eventfs_inode and that data structure can hold its inode number.
That last int was also purposely placed at the end of the structure to
prevent holes from within. Now that there's a 4 byte number to hold the
inode, both the inode number and the last integer can be moved up in the
structure for better cache locality, where the llist and rcu fields can be
moved to the end as they are only used when the eventfs_inode is being
deleted.
Link: https://lore.kernel.org/all/CAMuHMdXKiorg-jiuKoZpfZyDJ3Ynrfb8=X+c7x0Eewxn-YRdCA@mail.gmail.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240122152748.46897388@gandalf.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 53c41052ba31 ("eventfs: Have the inodes all for files and directories all be the same")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 852e46e239ee6db3cd220614cf8bce96e79227c2 upstream.
The original eventfs code added a wrapper around the dcache_readdir open
callback and created all the dentries and inodes at open, and increment
their ref count. A wrapper was added around the dcache_readdir release
function to decrement all the ref counts of those created inodes and
dentries. But this proved to be buggy[1] for when a kprobe was created
during a dir read, it would create a dentry between the open and the
release, and because the release would decrement all ref counts of all
files and directories, that would include the kprobe directory that was
not there to have its ref count incremented in open. This would cause the
ref count to go to negative and later crash the kernel.
To solve this, the dentries and inodes that were created and had their ref
count upped in open needed to be saved. That list needed to be passed from
the open to the release, so that the release would only decrement the ref
counts of the entries that were incremented in the open.
Unfortunately, the dcache_readdir logic was already using the
file->private_data, which is the only field that can be used to pass
information from the open to the release. What was done was the eventfs
created another descriptor that had a void pointer to save the
dcache_readdir pointer, and it wrapped all the callbacks, so that it could
save the list of entries that had their ref counts incremented in the
open, and pass it to the release. The wrapped callbacks would just put
back the dcache_readdir pointer and call the functions it used so it could
still use its data[2].
But Linus had an issue with the "hijacking" of the file->private_data
(unfortunately this discussion was on a security list, so no public link).
Which we finally agreed on doing everything within the iterate_shared
callback and leave the dcache_readdir out of it[3]. All the information
needed for the getents() could be created then.
But this ended up being buggy too[4]. The iterate_shared callback was not
the right place to create the dentries and inodes. Even Christian Brauner
had issues with that[5].
An attempt was to go back to creating the inodes and dentries at
the open, create an array to store the information in the
file->private_data, and pass that information to the other callbacks.[6]
The difference between that and the original method, is that it does not
use dcache_readdir. It also does not up the ref counts of the dentries and
pass them. Instead, it creates an array of a structure that saves the
dentry's name and inode number. That information is used in the
iterate_shared callback, and the array is freed in the dir release. The
dentries and inodes created in the open are not used for the iterate_share
or release callbacks. Just their names and inode numbers.
Linus did not like that either[7] and just wanted to remove the dentries
being created in iterate_shared and use the hard coded inode numbers.
[ All this while Linus enjoyed an unexpected vacation during the merge
window due to lack of power. ]
[1] https://lore.kernel.org/linux-trace-kernel/20230919211804.230edf1e@gandalf.local.home/
[2] https://lore.kernel.org/linux-trace-kernel/20230922163446.1431d4fa@gandalf.local.home/
[3] https://lore.kernel.org/linux-trace-kernel/20240104015435.682218477@goodmis.org/
[4] https://lore.kernel.org/all/202401152142.bfc28861-oliver.sang@intel.com/
[5] https://lore.kernel.org/all/20240111-unzahl-gefegt-433acb8a841d@brauner/
[6] https://lore.kernel.org/all/20240116114711.7e8637be@gandalf.local.home/
[7] https://lore.kernel.org/all/20240116170154.5bf0a250@gandalf.local.home/
Link: https://lore.kernel.org/linux-trace-kernel/20240116211353.573784051@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Ajay Kaher <ajay.kaher@broadcom.com>
Fixes: 493ec81a8fb8 ("eventfs: Stop using dcache_readdir() for getdents()")
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401152142.bfc28861-oliver.sang@intel.com
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e4624eb5a0ecaae0d2c4e3019bece119725bb98 upstream.
The ctx->pos was only updated when it added an entry, but the "skip to
current pos" check (c--) happened for every loop regardless of if the
entry was added or not. This inconsistency caused readdir to be incorrect.
It was due to:
for (i = 0; i < ei->nr_entries; i++) {
if (c > 0) {
c--;
continue;
}
mutex_lock(&eventfs_mutex);
/* If ei->is_freed then just bail here, nothing more to do */
if (ei->is_freed) {
mutex_unlock(&eventfs_mutex);
goto out;
}
r = entry->callback(name, &mode, &cdata, &fops);
mutex_unlock(&eventfs_mutex);
[..]
ctx->pos++;
}
But this can cause the iterator to return a file that was already read.
That's because of the way the callback() works. Some events may not have
all files, and the callback can return 0 to tell eventfs to skip the file
for this directory.
for instance, we have:
# ls /sys/kernel/tracing/events/ftrace/function
format hist hist_debug id inject
and
# ls /sys/kernel/tracing/events/sched/sched_switch/
enable filter format hist hist_debug id inject trigger
Where the function directory is missing "enable", "filter" and
"trigger". That's because the callback() for events has:
static int event_callback(const char *name, umode_t *mode, void **data,
const struct file_operations **fops)
{
struct trace_event_file *file = *data;
struct trace_event_call *call = file->event_call;
[..]
/*
* Only event directories that can be enabled should have
* triggers or filters, with the exception of the "print"
* event that can have a "trigger" file.
*/
if (!(call->flags & TRACE_EVENT_FL_IGNORE_ENABLE)) {
if (call->class->reg && strcmp(name, "enable") == 0) {
*mode = TRACE_MODE_WRITE;
*fops = &ftrace_enable_fops;
return 1;
}
if (strcmp(name, "filter") == 0) {
*mode = TRACE_MODE_WRITE;
*fops = &ftrace_event_filter_fops;
return 1;
}
}
if (!(call->flags & TRACE_EVENT_FL_IGNORE_ENABLE) ||
strcmp(trace_event_name(call), "print") == 0) {
if (strcmp(name, "trigger") == 0) {
*mode = TRACE_MODE_WRITE;
*fops = &event_trigger_fops;
return 1;
}
}
[..]
return 0;
}
Where the function event has the TRACE_EVENT_FL_IGNORE_ENABLE set.
This means that the entries array elements for "enable", "filter" and
"trigger" when called on the function event will have the callback return
0 and not 1, to tell eventfs to skip these files for it.
Because the "skip to current ctx->pos" check happened for all entries, but
the ctx->pos++ only happened to entries that exist, it would confuse the
reading of a directory. Which would cause:
# ls /sys/kernel/tracing/events/ftrace/function/
format hist hist hist_debug hist_debug id inject inject
The missing "enable", "filter" and "trigger" caused ls to show "hist",
"hist_debug" and "inject" twice.
Update the ctx->pos for every iteration to keep its update and the "skip"
update consistent. This also means that on error, the ctx->pos needs to be
decremented if it was incremented without adding something.
Link: https://lore.kernel.org/all/20240104150500.38b15a62@gandalf.local.home/
Link: https://lore.kernel.org/linux-trace-kernel/20240104220048.172295263@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 493ec81a8fb8e ("eventfs: Stop using dcache_readdir() for getdents()")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8186fff7ab649085e2c60d032d9a20a85af1d87c upstream.
Instead of walking the dentries on mount/remount to update the gid values of
all the dentries if a gid option is specified on mount, just update the root
inode. Add .getattr, .setattr, and .permissions on the tracefs inode
operations to update the permissions of the files and directories.
For all files and directories in the top level instance:
/sys/kernel/tracing/*
It will use the root inode as the default permissions. The inode that
represents: /sys/kernel/tracing (or wherever it is mounted).
When an instance is created:
mkdir /sys/kernel/tracing/instance/foo
The directory "foo" and all its files and directories underneath will use
the default of what foo is when it was created. A remount of tracefs will
not affect it.
If a user were to modify the permissions of any file or directory in
tracefs, it will also no longer be modified by a change in ownership of a
remount.
The events directory, if it is in the top level instance, will use the
tracefs root inode as the default ownership for itself and all the files and
directories below it.
For the events directory in an instance ("foo"), it will keep the ownership
of what it was when it was created, and that will be used as the default
ownership for the files and directories beneath it.
Link: https://lore.kernel.org/linux-trace-kernel/CAHk-=wjVdGkjDXBbvLn2wbZnqP4UsH46E3gqJ9m7UG6DpX2+WA@mail.gmail.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240103215016.1e0c9811@gandalf.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
