Changes in 4.19.80
panic: ensure preemption is disabled during panic()
f2fs: use EINVAL for superblock with invalid magic
USB: rio500: Remove Rio 500 kernel driver
USB: yurex: Don't retry on unexpected errors
USB: yurex: fix NULL-derefs on disconnect
USB: usb-skeleton: fix runtime PM after driver unbind
USB: usb-skeleton: fix NULL-deref on disconnect
xhci: Fix false warning message about wrong bounce buffer write length
xhci: Prevent device initiated U1/U2 link pm if exit latency is too long
xhci: Check all endpoints for LPM timeout
xhci: Fix USB 3.1 capability detection on early xHCI 1.1 spec based hosts
usb: xhci: wait for CNR controller not ready bit in xhci resume
xhci: Prevent deadlock when xhci adapter breaks during init
xhci: Increase STS_SAVE timeout in xhci_suspend()
USB: adutux: fix use-after-free on disconnect
USB: adutux: fix NULL-derefs on disconnect
USB: adutux: fix use-after-free on release
USB: iowarrior: fix use-after-free on disconnect
USB: iowarrior: fix use-after-free on release
USB: iowarrior: fix use-after-free after driver unbind
USB: usblp: fix runtime PM after driver unbind
USB: chaoskey: fix use-after-free on release
USB: ldusb: fix NULL-derefs on driver unbind
serial: uartlite: fix exit path null pointer
USB: serial: keyspan: fix NULL-derefs on open() and write()
USB: serial: ftdi_sio: add device IDs for Sienna and Echelon PL-20
USB: serial: option: add Telit FN980 compositions
USB: serial: option: add support for Cinterion CLS8 devices
USB: serial: fix runtime PM after driver unbind
USB: usblcd: fix I/O after disconnect
USB: microtek: fix info-leak at probe
USB: dummy-hcd: fix power budget for SuperSpeed mode
usb: renesas_usbhs: gadget: Do not discard queues in usb_ep_set_{halt,wedge}()
usb: renesas_usbhs: gadget: Fix usb_ep_set_{halt,wedge}() behavior
USB: legousbtower: fix slab info leak at probe
USB: legousbtower: fix deadlock on disconnect
USB: legousbtower: fix potential NULL-deref on disconnect
USB: legousbtower: fix open after failed reset request
USB: legousbtower: fix use-after-free on release
mei: me: add comet point (lake) LP device ids
mei: avoid FW version request on Ibex Peak and earlier
gpio: eic: sprd: Fix the incorrect EIC offset when toggling
Staging: fbtft: fix memory leak in fbtft_framebuffer_alloc
staging: vt6655: Fix memory leak in vt6655_probe
iio: adc: hx711: fix bug in sampling of data
iio: adc: ad799x: fix probe error handling
iio: adc: axp288: Override TS pin bias current for some models
iio: light: opt3001: fix mutex unlock race
efivar/ssdt: Don't iterate over EFI vars if no SSDT override was specified
perf llvm: Don't access out-of-scope array
perf inject jit: Fix JIT_CODE_MOVE filename
blk-wbt: fix performance regression in wbt scale_up/scale_down
CIFS: Gracefully handle QueryInfo errors during open
CIFS: Force revalidate inode when dentry is stale
CIFS: Force reval dentry if LOOKUP_REVAL flag is set
kernel/sysctl.c: do not override max_threads provided by userspace
mm/vmpressure.c: fix a signedness bug in vmpressure_register_event()
firmware: google: increment VPD key_len properly
gpiolib: don't clear FLAG_IS_OUT when emulating open-drain/open-source
iio: adc: stm32-adc: move registers definitions
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
cifs: use cifsInodeInfo->open_file_lock while iterating to avoid a panic
btrfs: fix incorrect updating of log root tree
btrfs: fix uninitialized ret in ref-verify
NFS: Fix O_DIRECT accounting of number of bytes read/written
MIPS: Disable Loongson MMI instructions for kernel build
MIPS: elf_hwcap: Export userspace ASEs
ACPICA: ACPI 6.3: PPTT add additional fields in Processor Structure Flags
ACPI/PPTT: Add support for ACPI 6.3 thread flag
arm64: topology: Use PPTT to determine if PE is a thread
Fix the locking in dcache_readdir() and friends
media: stkwebcam: fix runtime PM after driver unbind
arm64/sve: Fix wrong free for task->thread.sve_state
tracing/hwlat: Report total time spent in all NMIs during the sample
tracing/hwlat: Don't ignore outer-loop duration when calculating max_latency
ftrace: Get a reference counter for the trace_array on filter files
tracing: Get trace_array reference for available_tracers files
hwmon: Fix HWMON_P_MIN_ALARM mask
x86/asm: Fix MWAITX C-state hint value
PCI: vmd: Fix config addressing when using bus offsets
perf/hw_breakpoint: Fix arch_hw_breakpoint use-before-initialization
Linux 4.19.80
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I8ef1835585f79b752712a835852a4bc960ae3b97
commit e3dffa4f6c upstream.
VMD maps child device config spaces to the VMD Config BAR linearly
regardless of the starting bus offset. Because of this, the config
address decode must ignore starting bus offsets when mapping the BDF to
the config space address.
Fixes: 2a5a9c9a20 ("PCI: vmd: Add offset to bus numbers if necessary")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Sushma Kalakota <sushmax.kalakota@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 194c2c74f5 upstream.
As instances may have different tracers available, we need to look at the
trace_array descriptor that shows the list of the available tracers for the
instance. But there's a race between opening the file and an admin
deleting the instance. The trace_array_get() needs to be called before
accessing the trace_array.
Cc: stable@vger.kernel.org
Fixes: 607e2ea167 ("tracing: Set up infrastructure to allow tracers for instances")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ef16693af upstream.
The ftrace set_ftrace_filter and set_ftrace_notrace files are specific for
an instance now. They need to take a reference to the instance otherwise
there could be a race between accessing the files and deleting the instance.
It wasn't until the :mod: caching where these file operations started
referencing the trace_array directly.
Cc: stable@vger.kernel.org
Fixes: 673feb9d76 ("ftrace: Add :mod: caching infrastructure to trace_array")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4585fc59c0 upstream.
The system which has SVE feature crashed because of
the memory pointed by task->thread.sve_state was destroyed
by someone.
That is because sve_state is freed while the forking the
child process. The child process has the pointer of sve_state
which is same as the parent's because the child's task_struct
is copied from the parent's one. If the copy_process()
fails as an error on somewhere, for example, copy_creds(),
then the sve_state is freed even if the parent is alive.
The flow is as follows.
copy_process
p = dup_task_struct
=> arch_dup_task_struct
*dst = *src; // copy the entire region.
:
retval = copy_creds
if (retval < 0)
goto bad_fork_free;
:
bad_fork_free:
...
delayed_free_task(p);
=> free_task
=> arch_release_task_struct
=> fpsimd_release_task
=> __sve_free
=> kfree(task->thread.sve_state);
// free the parent's sve_state
Move child's sve_state = NULL and clearing TIF_SVE flag
to arch_dup_task_struct() so that the child doesn't free the
parent's one.
There is no need to wait until copy_process() to clear TIF_SVE for
dst, because the thread flags for dst are initialized already by
copying the src task_struct.
This change simplifies the code, so get rid of comments that are no
longer needed.
As a note, arm64 used to have thread_info on the stack. So it
would not be possible to clear TIF_SVE until the stack is initialized.
From commit c02433dd6d ("arm64: split thread_info from task stack"),
the thread_info is part of the task, so it should be valid to modify
the flag from arch_dup_task_struct().
Cc: stable@vger.kernel.org # 4.15.x-
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reported-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Suggested-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30045f2174 upstream.
Since commit c2b71462d2 ("USB: core: Fix bug caused by duplicate
interface PM usage counter") USB drivers must always balance their
runtime PM gets and puts, including when the driver has already been
unbound from the interface.
Leaving the interface with a positive PM usage counter would prevent a
later bound driver from suspending the device.
Note that runtime PM has never actually been enabled for this driver
since the support_autosuspend flag in its usb_driver struct is not set.
Fixes: c2b71462d2 ("USB: core: Fix bug caused by duplicate interface PM usage counter")
Cc: stable <stable@vger.kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191001084908.2003-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4f4de5e5e upstream.
There are two problems in dcache_readdir() - one is that lockless traversal
of the list needs non-trivial cooperation of d_alloc() (at least a switch
to list_add_rcu(), and probably more than just that) and another is that
it assumes that no removal will happen without the directory locked exclusive.
Said assumption had always been there, never had been stated explicitly and
is violated by several places in the kernel (devpts and selinuxfs).
* replacement of next_positive() with different calling conventions:
it returns struct list_head * instead of struct dentry *; the latter is
passed in and out by reference, grabbing the result and dropping the original
value.
* scan is under ->d_lock. If we run out of timeslice, cursor is moved
after the last position we'd reached and we reschedule; then the scan continues
from that place. To avoid livelocks between multiple lseek() (with cursors
getting moved past each other, never reaching the real entries) we always
skip the cursors, need_resched() or not.
* returned list_head * is either ->d_child of dentry we'd found or
->d_subdirs of parent (if we got to the end of the list).
* dcache_readdir() and dcache_dir_lseek() switched to new helper.
dcache_readdir() always holds a reference to dentry passed to dir_emit() now.
Cursor is moved to just before the entry where dir_emit() has failed or into
the very end of the list, if we'd run out.
* move_cursor() eliminated - it had sucky calling conventions and
after fixing that it became simply list_move() (in lseek and scan_positives)
or list_move_tail() (in readdir).
All operations with the list are under ->d_lock now, and we do not
depend upon having all file removals done with parent locked exclusive
anymore.
Cc: stable@vger.kernel.org
Reported-by: "zhengbin (A)" <zhengbin13@huawei.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 98dc19902a upstream.
ACPI 6.3 adds a thread flag to represent if a CPU/PE is
actually a thread. Given that the MPIDR_MT bit may not
represent this information consistently on homogeneous machines
we should prefer the PPTT flag if its available.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Robert Richter <rrichter@marvell.com>
[will: made acpi_cpu_is_threaded() return 'bool']
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f2b4fd674 upstream.
GCC 9.x automatically enables support for Loongson MMI instructions when
using some -march= flags, and then errors out when -msoft-float is
specified with:
cc1: error: ‘-mloongson-mmi’ must be used with ‘-mhard-float’
The kernel shouldn't be using these MMI instructions anyway, just as it
doesn't use floating point instructions. Explicitly disable them in
order to fix the build with GCC 9.x.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 3702bba5eb ("MIPS: Loongson: Add GCC 4.4 support for Loongson2E")
Fixes: 6f7a251a25 ("MIPS: Loongson: Add basic Loongson 2F support")
Fixes: 5188129b8c ("MIPS: Loongson-3: Improve -march option and move it to Platform")
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: stable@vger.kernel.org # v2.6.32+
Cc: linux-mips@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 031d73ed76 upstream.
When a series of O_DIRECT reads or writes are truncated, either due to
eof or due to an error, then we should return the number of contiguous
bytes that were received/sent starting at the offset specified by the
application.
Currently, we are failing to correctly check contiguity, and so we're
failing the generic/465 in xfstests when the race between the read
and write RPCs causes the file to get extended while the 2 reads are
outstanding. If the first read RPC call wins the race and returns with
eof set, we should treat the second read RPC as being truncated.
Reported-by: Su Yanjun <suyj.fnst@cn.fujitsu.com>
Fixes: 1ccbad9f9f ("nfs: fix DIO good bytes calculation")
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5f4987e86 upstream.
Coverity caught a case where we could return with a uninitialized value
in ret in process_leaf. This is actually pretty likely because we could
very easily run into a block group item key and have a garbage value in
ret and think there was an errror. Fix this by initializing ret to 0.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: fd708b81d9 ("Btrfs: add a extent ref verify tool")
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4203e96894 upstream.
We've historically had reports of being unable to mount file systems
because the tree log root couldn't be read. Usually this is the "parent
transid failure", but could be any of the related errors, including
"fsid mismatch" or "bad tree block", depending on which block got
allocated.
The modification of the individual log root items are serialized on the
per-log root root_mutex. This means that any modification to the
per-subvol log root_item is completely protected.
However we update the root item in the log root tree outside of the log
root tree log_mutex. We do this in order to allow multiple subvolumes
to be updated in each log transaction.
This is problematic however because when we are writing the log root
tree out we update the super block with the _current_ log root node
information. Since these two operations happen independently of each
other, you can end up updating the log root tree in between writing out
the dirty blocks and setting the super block to point at the current
root.
This means we'll point at the new root node that hasn't been written
out, instead of the one we should be pointing at. Thus whatever garbage
or old block we end up pointing at complains when we mount the file
system later and try to replay the log.
Fix this by copying the log's root item into a local root item copy.
Then once we're safely under the log_root_tree->log_mutex we update the
root item in the log_root_tree. This way we do not modify the
log_root_tree while we're committing it, fixing the problem.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Chris Mason <clm@fb.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dcb1092017 ]
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31922f62bb ]
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e735244e2c ]
When emulating open-drain/open-source by not actively driving the output
lines - we're simply changing their mode to input. This is wrong as it
will then make it impossible to change the value of such line - it's now
considered to actually be in input mode. If we want to still use the
direction_input() callback for simplicity then we need to set FLAG_IS_OUT
manually in gpiod_direction_output() and not clear it in
gpio_set_open_drain_value_commit() and
gpio_set_open_source_value_commit().
Fixes: c663e5f567 ("gpio: support native single-ended hardware drivers")
Cc: stable@vger.kernel.org
Reported-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[Bartosz: backported to v5.3, v4.19]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 442f1e746e ]
Commit 4b708b7b1a ("firmware: google: check if size is valid when
decoding VPD data") adds length checks, but the new vpd_decode_entry()
function botched the logic -- it adds the key length twice, instead of
adding the key and value lengths separately.
On my local system, this means vpd.c's vpd_section_create_attribs() hits
an error case after the first attribute it parses, since it's no longer
looking at the correct offset. With this patch, I'm back to seeing all
the correct attributes in /sys/firmware/vpd/...
Fixes: 4b708b7b1a ("firmware: google: check if size is valid when decoding VPD data")
Cc: <stable@vger.kernel.org>
Cc: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20190930214522.240680-1-briannorris@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b0f53dbc4b upstream.
Partially revert 16db3d3f11 ("kernel/sysctl.c: threads-max observe
limits") because the patch is causing a regression to any workload which
needs to override the auto-tuning of the limit provided by kernel.
set_max_threads is implementing a boot time guesstimate to provide a
sensible limit of the concurrently running threads so that runaways will
not deplete all the memory. This is a good thing in general but there
are workloads which might need to increase this limit for an application
to run (reportedly WebSpher MQ is affected) and that is simply not
possible after the mentioned change. It is also very dubious to
override an admin decision by an estimation that doesn't have any direct
relation to correctness of the kernel operation.
Fix this by dropping set_max_threads from sysctl_max_threads so any
value is accepted as long as it fits into MAX_THREADS which is important
to check because allowing more threads could break internal robust futex
restriction. While at it, do not use MIN_THREADS as the lower boundary
because it is also only a heuristic for automatic estimation and admin
might have a good reason to stop new threads to be created even when
below this limit.
This became more severe when we switched x86 from 4k to 8k kernel
stacks. Starting since 6538b8ea88 ("x86_64: expand kernel stack to
16K") (3.16) we use THREAD_SIZE_ORDER = 2 and that halved the auto-tuned
value.
In the particular case
3.12
kernel.threads-max = 515561
4.4
kernel.threads-max = 200000
Neither of the two values is really insane on 32GB machine.
I am not sure we want/need to tune the max_thread value further. If
anything the tuning should be removed altogether if proven not useful in
general. But we definitely need a way to override this auto-tuning.
Link: http://lkml.kernel.org/r/20190922065801.GB18814@dhcp22.suse.cz
Fixes: 16db3d3f11 ("kernel/sysctl.c: threads-max observe limits")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b3d0ef984 upstream.
Mark inode for force revalidation if LOOKUP_REVAL flag is set.
This tells the client to actually send a QueryInfo request to
the server to obtain the latest metadata in case a directory
or a file were changed remotely. Only do that if the client
doesn't have a lease for the file to avoid unneeded round
trips to the server.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c82e5ac7fe upstream.
Currently the client indicates that a dentry is stale when inode
numbers or type types between a local inode and a remote file
don't match. If this is the case attributes is not being copied
from remote to local, so, it is already known that the local copy
has stale metadata. That's why the inode needs to be marked for
revalidation in order to tell the VFS to lookup the dentry again
before openning a file. This prevents unexpected stale errors
to be returned to the user space when openning a file.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 30573a82fb upstream.
Currently if the client identifies problems when processing
metadata returned in CREATE response, the open handle is being
leaked. This causes multiple problems like a file missing a lease
break by that client which causes high latencies to other clients
accessing the file. Another side-effect of this is that the file
can't be deleted.
Fix this by closing the file after the client hits an error after
the file was opened and the open descriptor wasn't returned to
the user space. Also convert -ESTALE to -EOPENSTALE to allow
the VFS to revalidate a dentry and retry the open.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b84477d3eb upstream.
scale_up wakes up waiters after scaling up. But after scaling max, it
should not wake up more waiters as waiters will not have anything to
do. This patch fixes this by making scale_up (and also scale_down)
return when threshold is reached.
This bug causes increased fdatasync latency when fdatasync and dd
conv=sync are performed in parallel on 4.19 compared to 4.14. This
bug was introduced during refactoring of blk-wbt code.
Fixes: a79050434b ("blk-rq-qos: refactor out common elements of blk-wbt")
Cc: stable@vger.kernel.org
Cc: Josef Bacik <jbacik@fb.com>
Signed-off-by: Harshad Shirwadkar <harshadshirwadkar@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82f3015635 upstream.
When an end-of-conversion interrupt is received after performing a
single-shot reading of the light sensor, the driver was waking up the
result ready queue before checking opt->ok_to_ignore_lock to determine
if it should unlock the mutex. The problem occurred in the case where
the other thread woke up and changed the value of opt->ok_to_ignore_lock
to false prior to the interrupt thread performing its read of the
variable. In this case, the mutex would be unlocked twice.
Signed-off-by: David Frey <dpfrey@gmail.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Fixes: 94a9b7b180 ("iio: light: add support for TI's opt3001 light sensor")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 972917419a upstream.
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4043ecfb5f upstream.
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd81e6fa8e upstream.
The driver is using its struct usb_device pointer as an inverted
disconnected flag, but was setting it to NULL before making sure all
completion handlers had run. This could lead to a NULL-pointer
dereference in a number of dev_dbg and dev_err statements in the
completion handlers which relies on said pointer.
Fix this by unconditionally stopping all I/O and preventing
resubmissions by poisoning the interrupt URBs at disconnect and using a
dedicated disconnected flag.
This also makes sure that all I/O has completed by the time the
disconnect callback returns.
Fixes: 9d974b2a06 ("USB: legousbtower.c: remove err() usage")
Fixes: fef526cae7 ("USB: legousbtower: remove custom debug macro")
Fixes: 4dae996380 ("USB: legotower: remove custom debug macro and module parameter")
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20190919083039.30898-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
