[ Upstream commit 1e9ac114c4 ]
In btsdio_probe, &data->work was bound with btsdio_work.In
btsdio_send_frame, it was started by schedule_work.
If we call btsdio_remove with an unfinished job, there may
be a race condition and cause UAF bug on hdev.
Fixes: ddbaf13e36 ("[Bluetooth] Add generic driver for Bluetooth SDIO devices")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d44ab9e20 ]
On most devices using the btqcomsmd driver (e.g. the DragonBoard 410c
and other devices based on the Qualcomm MSM8916/MSM8909/... SoCs)
the Bluetooth firmware seems to become unresponsive for a while after
setting the BD address. On recent kernel versions (at least 5.17+)
this often causes timeouts for subsequent commands, e.g. the HCI reset
sent by the Bluetooth core during initialization:
Bluetooth: hci0: Opcode 0x c03 failed: -110
Unfortunately this behavior does not seem to be documented anywhere.
Experimentation suggests that the minimum necessary delay to avoid
the problem is ~150us. However, to be sure add a sleep for > 1ms
in case it is a bit longer on other firmware versions.
Older kernel versions are likely also affected, although perhaps with
slightly different errors or less probability. Side effects can easily
hide the issue in most cases, e.g. unrelated incoming interrupts that
cause the necessary delay.
Fixes: 1511cc750c ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1de5c78eb ]
In device_for_each_child_node(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6214894f49 ]
The hvc machinery registers both a console and a tty device based on
the hv ops provided by the specific implementation. Those two
interfaces however have different locks, and there's no single locks
that's shared between the tty and the console implementations, hence
the driver needs to protect itself against concurrent accesses.
Otherwise concurrent calls using the split interfaces are likely to
corrupt the ring indexes, leaving the console unusable.
Introduce a lock to xencons_info to serialize accesses to the shared
ring. This is only required when using the shared memory console,
concurrent accesses to the hypercall based console implementation are
not an issue.
Note the conditional logic in domU_read_console() is slightly modified
so the notify_daemon() call can be done outside of the locked region:
it's an hypercall and there's no need for it to be done with the lock
held.
Fixes: b536b4b962 ('xen: use the hvc console infrastructure for Xen console')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20221130150919.13935-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa01c67de5 ]
The FEI field of C2HTermReq/H2CTermReq is 4 bytes but not 4-byte-aligned
in the NVMe/TCP specification (it is located at offset 10 in the PDU).
Split it into two 16-bit integers in struct nvme_tcp_term_pdu
so no padding is inserted. There should also be 10 reserved bytes after.
There are currently no users of this type.
Fixes: fc221d0544 ("nvme-tcp: Add protocol header")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Caleb Sander <csander@purestorage.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4fe3c88552 ]
There are memory leaks reported by kmemleak:
unreferenced object 0xffff888106500800 (size 128):
comm "modprobe", pid 1017, jiffies 4297787785 (age 67.152s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000970ce626>] __kmem_cache_alloc_node+0x20c/0x380
[<00000000fb5f78d9>] kmalloc_trace+0x2f/0xb0
[<000000000e947e2a>] idt77252_init_one+0x2847/0x3c90 [idt77252]
[<000000006efb048e>] local_pci_probe+0xeb/0x1a0
...
unreferenced object 0xffff888106500b00 (size 128):
comm "modprobe", pid 1017, jiffies 4297787785 (age 67.152s)
hex dump (first 32 bytes):
00 20 3d 01 80 88 ff ff 00 20 3d 01 80 88 ff ff . =...... =.....
f0 23 3d 01 80 88 ff ff 00 20 3d 01 00 00 00 00 .#=...... =.....
backtrace:
[<00000000970ce626>] __kmem_cache_alloc_node+0x20c/0x380
[<00000000fb5f78d9>] kmalloc_trace+0x2f/0xb0
[<00000000f451c5be>] alloc_scq.constprop.0+0x4a/0x400 [idt77252]
[<00000000e6313849>] idt77252_init_one+0x28cf/0x3c90 [idt77252]
The root cause is traced to the vc_maps which alloced in open_card_oam()
are not freed in close_card_oam(). The vc_maps are used to record
open connections, so when close a vc_map in close_card_oam(), the memory
should be freed. Moreover, the ubr0 is not closed when close a idt77252
device, leading to the memory leak of vc_map and scq_info.
Fix them by adding kfree in close_card_oam() and implementing new
close_card_ubr0() to close ubr0.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Link: https://lore.kernel.org/r/20230320143318.2644630-1-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44d553188c ]
When ETS configurations are queried by the user to get the mapping
assignment between packet priority and traffic class, only priorities up
to maximum TCs are queried from QTCT register in FW to retrieve their
assigned TC, leaving the rest of the priorities mapped to the default
TC #0 which might be misleading.
Fix by querying the TC mapping of all priorities on each ETS query,
regardless of the maximum number of TCs configured in FW.
Fixes: 820c2c5e77 ("net/mlx5e: Read ETS settings directly from firmware")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10ec8ca8ec ]
We've seen recent AWS EKS (Kubernetes) user reports like the following:
After upgrading EKS nodes from v20230203 to v20230217 on our 1.24 EKS
clusters after a few days a number of the nodes have containers stuck
in ContainerCreating state or liveness/readiness probes reporting the
following error:
Readiness probe errored: rpc error: code = Unknown desc = failed to
exec in container: failed to start exec "4a11039f730203ffc003b7[...]":
OCI runtime exec failed: exec failed: unable to start container process:
unable to init seccomp: error loading seccomp filter into kernel:
error loading seccomp filter: errno 524: unknown
However, we had not been seeing this issue on previous AMIs and it only
started to occur on v20230217 (following the upgrade from kernel 5.4 to
5.10) with no other changes to the underlying cluster or workloads.
We tried the suggestions from that issue (sysctl net.core.bpf_jit_limit=452534528)
which helped to immediately allow containers to be created and probes to
execute but after approximately a day the issue returned and the value
returned by cat /proc/vmallocinfo | grep bpf_jit | awk '{s+=$2} END {print s}'
was steadily increasing.
I tested bpf tree to observe bpf_jit_charge_modmem, bpf_jit_uncharge_modmem
their sizes passed in as well as bpf_jit_current under tcpdump BPF filter,
seccomp BPF and native (e)BPF programs, and the behavior all looks sane
and expected, that is nothing "leaking" from an upstream perspective.
The bpf_jit_limit knob was originally added in order to avoid a situation
where unprivileged applications loading BPF programs (e.g. seccomp BPF
policies) consuming all the module memory space via BPF JIT such that loading
of kernel modules would be prevented. The default limit was defined back in
2018 and while good enough back then, we are generally seeing far more BPF
consumers today.
Adjust the limit for the BPF JIT pool from originally 1/4 to now 1/2 of the
module memory space to better reflect today's needs and avoid more users
running into potentially hard to debug issues.
Fixes: fdadd04931 ("bpf: fix bpf_jit_limit knob for PAGE_SIZE >= 64K")
Reported-by: Stephen Haynes <sh@synk.net>
Reported-by: Lefteris Alexakis <lefteris.alexakis@kpn.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://github.com/awslabs/amazon-eks-ami/issues/1179
Link: https://github.com/awslabs/amazon-eks-ami/issues/1219
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230320143725.8394-1-daniel@iogearbox.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47f9e4c924 ]
The key which gets cached in task structure from a kernel thread does not
get invalidated even after expiry. Due to which, a new key request from
kernel thread will be served with the cached key if it's present in task
struct irrespective of the key validity. The change is to not cache key in
task_struct when key requested from kernel thread so that kernel thread
gets a valid key on every key request.
The problem has been seen with the cifs module doing DNS lookups from a
kernel thread and the results getting pinned by being attached to that
kernel thread's cache - and thus not something that can be easily got rid
of. The cache would ordinarily be cleared by notify-resume, but kernel
threads don't do that.
This isn't seen with AFS because AFS is doing request_key() within the
kernel half of a user thread - which will do notify-resume.
Fixes: 7743c48e54 ("keys: Cache result of request_key*() temporarily in task_struct")
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Steve French <smfrench@gmail.com>
cc: keyrings@vger.kernel.org
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/CAGypqWw951d=zYRbdgNR4snUDvJhWL=q3=WOyh7HhSJupjz2vA@mail.gmail.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bebe933d35 ]
The current Gelic Etherenet driver was checking the return value of its
dma_map_single call, and not using the dma_mapping_error() routine.
Fixes runtime problems like these:
DMA-API: ps3_gelic_driver sb_05: device driver failed to check map error
WARNING: CPU: 0 PID: 0 at kernel/dma/debug.c:1027 .check_unmap+0x888/0x8dc
Fixes: 02c1889166 ("ps3: gigabit ethernet driver for PS3, take3")
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19b3bb51c3 ]
The Gelic Ethernet device needs to have the RX sk_buffs aligned to
GELIC_NET_RXBUF_ALIGN, and also the length of the RX sk_buffs must
be a multiple of GELIC_NET_RXBUF_ALIGN.
The current Gelic Ethernet driver was not allocating sk_buffs large
enough to allow for this alignment.
Also, correct the maximum and minimum MTU sizes, and add a new
preprocessor macro for the maximum frame size, GELIC_NET_MAX_FRAME.
Fixes various randomly occurring runtime network errors.
Fixes: 02c1889166 ("ps3: gigabit ethernet driver for PS3, take3")
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b6bc5b8bd ]
In emac_probe, &adpt->work_thread is bound with
emac_work_thread. Then it will be started by timeout
handler emac_tx_timeout or a IRQ handler emac_isr.
If we remove the driver which will call emac_remove
to make cleanup, there may be a unfinished work.
The possible sequence is as follows:
Fix it by finishing the work before cleanup in the emac_remove
and disable timeout response.
CPU0 CPU1
|emac_work_thread
emac_remove |
free_netdev |
kfree(netdev); |
|emac_reinit_locked
|emac_mac_down
|//use netdev
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8d20c3ded ]
In xirc2ps_probe, the local->tx_timeout_task was bounded
with xirc2ps_tx_timeout_task. When timeout occurs,
it will call xirc_tx_timeout->schedule_work to start the
work.
When we call xirc2ps_detach to remove the driver, there
may be a sequence as follows:
Stop responding to timeout tasks and complete scheduled
tasks before cleanup in xirc2ps_detach, which will fix
the problem.
CPU0 CPU1
|xirc2ps_tx_timeout_task
xirc2ps_detach |
free_netdev |
kfree(dev); |
|
| do_reset
| //use dev
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25143b6a01 ]
We have to make sure that the info returned by the helper is valid
before using it.
Found by Linux Verification Center (linuxtesting.org) with the SVACE
static analysis tool.
Fixes: f990c82c38 ("qed*: Add support for ndo_set_vf_trust")
Fixes: 733def6a04 ("qed*: IOV link control")
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c78850045 ]
When reading from I2C, the Tx watermark is set to 0. Unfortunately the
TDF (transmit data flag) is enabled when Tx FIFO entries is equal or less
than watermark. So it is set in every case, hence the reset default of 1.
This results in the MSR_RDF _and_ MSR_TDF flags to be set thus trying
to send Tx data on a read message.
Mask the IRQ status to filter for wanted flags only.
Fixes: a55fa9d0e4 ("i2c: imx-lpi2c: add low power i2c bus driver")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02c83791ef ]
vf reset nack actually represents the reset operation itself is
performed but no address is assigned. Therefore, e1000_reset_hw_vf
should fill the "perm_addr" with the zero address and return success on
such an occasion. This prevents its callers in netdev.c from saying PF
still resetting, and instead allows them to correctly report that no
address is assigned.
Fixes: 6ddbc4cf1f ("igb: Indicate failure on vf reset for empty mac address")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de58647b43 ]
Currently, IAVF's decode_rx_desc_ptype() correctly reports payload type
of L4 for IPv4 UDP packets and IPv{4,6} TCP, but only L3 for IPv6 UDP.
Originally, i40e, ice and iavf were affected.
Commit 73df8c9e3e ("i40e: Correct UDP packet header for non_tunnel-ipv6")
fixed that in i40e, then
commit 638a0c8c88 ("ice: fix incorrect payload indicator on PTYPE")
fixed that for ice.
IPv6 UDP is L4 obviously. Fix it and make iavf report correct L4 hash
type for such packets, so that the stack won't calculate it on CPU when
needs it.
Fixes: 206812b5fc ("i40e/i40evf: i40e implementation for skb_set_hash")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32d57f667f ]
Condition, which checks whether the netdev has hashing enabled is
inverted. Basically, the tagged commit effectively disabled passing flow
hash from descriptor to skb, unless user *disables* it via Ethtool.
Commit a876c3ba59 ("i40e/i40evf: properly report Rx packet hash")
fixed this problem, but only for i40e.
Invert the condition now in iavf and unblock passing hash to skbs again.
Fixes: 857942fd1a ("i40e: Fix Rx hash reported to the stack by our driver")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06615d11cc ]
In da9150_charger_probe, &charger->otg_work is bound with
da9150_charger_otg_work. da9150_charger_otg_ncb may be
called to start the work.
If we remove the module which will call da9150_charger_remove
to make cleanup, there may be a unfinished work. The possible
sequence is as follows:
Fix it by canceling the work before cleanup in the da9150_charger_remove
CPU0 CPUc1
|da9150_charger_otg_work
da9150_charger_remove |
power_supply_unregister |
device_unregister |
power_supply_dev_release|
kfree(psy) |
|
| power_supply_changed(charger->usb);
| //use
Fixes: c1a281e34d ("power: Add support for DA9150 Charger")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 04a331c9dd reverted change 2537b637ea (ipv4: Fix
incorrect route flushing when source address is deleted) that
added the fib_tests.sh file back with wrong permissions.
Fix that in this commit.
Signed-off-by: Rishabh Bhatnagar <risbhat@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c5d422124 upstream.
The default maximum data buffer size for this interface is UHID_DATA_MAX
(4k). When data buffers are being processed, ensure this value is used
when ensuring the sanity, rather than a value between the user provided
value and HID_MAX_BUFFER_SIZE (16k).
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1a37ed00d upstream.
Presently, when a report is processed, its proposed size, provided by
the user of the API (as Report Size * Report Count) is compared against
the subsystem default HID_MAX_BUFFER_SIZE (16k). However, some
low-level HID drivers allocate a reduced amount of memory to their
buffers (e.g. UHID only allocates UHID_DATA_MAX (4k) buffers), rending
this check inadequate in some cases.
In these circumstances, if the received report ends up being smaller
than the proposed report size, the remainder of the buffer is zeroed.
That is, the space between sizeof(csize) (size of the current report)
and the rsize (size proposed i.e. Report Size * Report Count), which can
be handled up to HID_MAX_BUFFER_SIZE (16k). Meaning that memset()
shoots straight past the end of the buffer boundary and starts zeroing
out in-use values, often resulting in calamity.
This patch introduces a new variable into 'struct hid_ll_driver' where
individual low-level drivers can over-ride the default maximum value of
HID_MAX_BUFFER_SIZE (16k) with something more sympathetic to the
interface.
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[Lee: Backported to v5.10.y]
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac91e69805 upstream.
Sheng Bi reports that pci_bridge_secondary_bus_reset() may fail to wait
for devices on the secondary bus to become accessible after reset:
Although it does call pci_dev_wait(), it erroneously passes the bridge's
pci_dev rather than that of a child. The bridge of course is always
accessible while its secondary bus is reset, so pci_dev_wait() returns
immediately.
Sheng Bi proposes introducing a new pci_bridge_secondary_bus_wait()
function which is called from pci_bridge_secondary_bus_reset():
https://lore.kernel.org/linux-pci/20220523171517.32407-1-windy.bi.enflame@gmail.com/
However we already have pci_bridge_wait_for_secondary_bus() which does
almost exactly what we need. So far it's only called on resume from
D3cold (which implies a Fundamental Reset per PCIe r6.0 sec 5.8).
Re-using it for Secondary Bus Resets is a leaner and more rational
approach than introducing a new function.
That only requires a few minor tweaks:
- Amend pci_bridge_wait_for_secondary_bus() to await accessibility of
the first device on the secondary bus by calling pci_dev_wait() after
performing the prescribed delays. pci_dev_wait() needs two parameters,
a reset reason and a timeout, which callers must now pass to
pci_bridge_wait_for_secondary_bus(). The timeout is 1 sec for resume
(PCIe r6.0 sec 6.6.1) and 60 sec for reset (commit 821cdad5c4 ("PCI:
Wait up to 60 seconds for device to become ready after FLR")).
Introduce a PCI_RESET_WAIT macro for the 1 sec timeout.
- Amend pci_bridge_wait_for_secondary_bus() to return 0 on success or
-ENOTTY on error for consumption by pci_bridge_secondary_bus_reset().
- Drop an unnecessary 1 sec delay from pci_reset_secondary_bus() which
is now performed by pci_bridge_wait_for_secondary_bus(). A static
delay this long is only necessary for Conventional PCI, so modern
PCIe systems benefit from shorter reset times as a side effect.
Fixes: 6b2f1351af ("PCI: Wait for device to become ready after secondary bus reset")
Link: https://lore.kernel.org/r/da77c92796b99ec568bd070cbe4725074a117038.1673769517.git.lukas@wunner.de
Reported-by: Sheng Bi <windy.bi.enflame@gmail.com>
Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a52e5cdbe8 upstream.
The code which handles the ipl report is searching for a free location
in memory where it could copy the component and certificate entries to.
It checks for intersection between the sections required for the kernel
and the component/certificate data area, but fails to check whether
the data structures linking these data areas together intersect.
This might cause the iplreport copy code to overwrite the iplreport
itself. Fix this by adding two addtional intersection checks.
Cc: <stable@vger.kernel.org>
Fixes: 9641b8cc73 ("s390/ipl: read IPL report at early boot")
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbebd68f59 upstream.
cmdline_find_option() may fail before doing any initialization of
the buffer array. This may lead to unpredictable results when the same
buffer is used later in calls to strncmp() function. Fix the issue by
returning early if cmdline_find_option() returns an error.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: aca20d5462 ("x86/mm: Add support to make use of Secure Memory Encryption")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20230306160656.14844-1-n.zhandarovich@fintech.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 203873a535 upstream.
Find a valid modeline depending on the machine graphic card
configuration and add the fb_check_var() function to validate
Xorg provided graphics settings.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee92fa4433 upstream.
KASAN reported follow problem:
BUG: KASAN: use-after-free in lookup_rec
Read of size 8 at addr ffff000199270ff0 by task modprobe
CPU: 2 Comm: modprobe
Call trace:
kasan_report
__asan_load8
lookup_rec
ftrace_location
arch_check_ftrace_location
check_kprobe_address_safe
register_kprobe
When checking pg->records[pg->index - 1].ip in lookup_rec(), it can get a
pg which is newly added to ftrace_pages_start in ftrace_process_locs().
Before the first pg->index++, index is 0 and accessing pg->records[-1].ip
will cause this problem.
Don't check the ip when pg->index is 0.
Link: https://lore.kernel.org/linux-trace-kernel/20230309080230.36064-1-chenzhongjin@huawei.com
Cc: stable@vger.kernel.org
Fixes: 9644302e33 ("ftrace: Speed up search by skipping pages by address")
Suggested-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 112e66017b upstream.
The effective values of the guest CR0 and CR4 registers may differ from
those included in the VMCS12. In particular, disabling EPT forces
CR4.PAE=1 and disabling unrestricted guest mode forces CR0.PG=CR0.PE=1.
Therefore, checks on these bits cannot be delegated to the processor
and must be performed by KVM.
Reported-by: Reima ISHII <ishiir@g.ecc.u-tokyo.ac.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2411fd94ce upstream.
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 250870824c ]
GCC warns about the pattern sizeof(void*)/sizeof(void), as it looks like
the abuse of a pattern to calculate the array size. This pattern appears
in the unevaluated part of the ternary operator in _INTC_ARRAY if the
parameter is NULL.
The replacement uses an alternate approach to return 0 in case of NULL
which does not generate the pattern sizeof(void*)/sizeof(void), but still
emits the warning if _INTC_ARRAY is called with a nonarray parameter.
This patch is required for successful compilation with -Werror enabled.
The idea to use _Generic for type distinction is taken from Comment #7
in https://gcc.gnu.org/bugzilla/show_bug.cgi?id=108483 by Jakub Jelinek
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/619fa552-c988-35e5-b1d7-fe256c46a272@mkarcher.dialup.fu-berlin.de
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f7bfd6f81 ]
Syzbot reported a hung task problem:
==================================================================
INFO: task syz-executor232:5073 blocked for more than 143 seconds.
Not tainted 6.2.0-rc2-syzkaller-00024-g512dee0c00ad #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-exec232 state:D stack:21024 pid:5073 ppid:5072 flags:0x00004004
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5244 [inline]
__schedule+0x995/0xe20 kernel/sched/core.c:6555
schedule+0xcb/0x190 kernel/sched/core.c:6631
__wait_on_freeing_inode fs/inode.c:2196 [inline]
find_inode_fast+0x35a/0x4c0 fs/inode.c:950
iget_locked+0xb1/0x830 fs/inode.c:1273
__ext4_iget+0x22e/0x3ed0 fs/ext4/inode.c:4861
ext4_xattr_inode_iget+0x68/0x4e0 fs/ext4/xattr.c:389
ext4_xattr_inode_dec_ref_all+0x1a7/0xe50 fs/ext4/xattr.c:1148
ext4_xattr_delete_inode+0xb04/0xcd0 fs/ext4/xattr.c:2880
ext4_evict_inode+0xd7c/0x10b0 fs/ext4/inode.c:296
evict+0x2a4/0x620 fs/inode.c:664
ext4_orphan_cleanup+0xb60/0x1340 fs/ext4/orphan.c:474
__ext4_fill_super fs/ext4/super.c:5516 [inline]
ext4_fill_super+0x81cd/0x8700 fs/ext4/super.c:5644
get_tree_bdev+0x400/0x620 fs/super.c:1282
vfs_get_tree+0x88/0x270 fs/super.c:1489
do_new_mount+0x289/0xad0 fs/namespace.c:3145
do_mount fs/namespace.c:3488 [inline]
__do_sys_mount fs/namespace.c:3697 [inline]
__se_sys_mount+0x2d3/0x3c0 fs/namespace.c:3674
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fa5406fd5ea
RSP: 002b:00007ffc7232f968 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007fa5406fd5ea
RDX: 0000000020000440 RSI: 0000000020000000 RDI: 00007ffc7232f970
RBP: 00007ffc7232f970 R08: 00007ffc7232f9b0 R09: 0000000000000432
R10: 0000000000804a03 R11: 0000000000000202 R12: 0000000000000004
R13: 0000555556a7a2c0 R14: 00007ffc7232f9b0 R15: 0000000000000000
</TASK>
==================================================================
The problem is that the inode contains an xattr entry with ea_inum of 15
when cleaning up an orphan inode <15>. When evict inode <15>, the reference
counting of the corresponding EA inode is decreased. When EA inode <15> is
found by find_inode_fast() in __ext4_iget(), it is found that the EA inode
holds the I_FREEING flag and waits for the EA inode to complete deletion.
As a result, when inode <15> is being deleted, we wait for inode <15> to
complete the deletion, resulting in an infinite loop and triggering Hung
Task. To solve this problem, we only need to check whether the ino of EA
inode and parent is the same before getting EA inode.
Link: https://syzkaller.appspot.com/bug?extid=77d6fcc37bbb92f26048
Reported-by: syzbot+77d6fcc37bbb92f26048@syzkaller.appspotmail.com
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230110133436.996350-1-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23892d383b ]
Bug description and fix:
1. Write data to a file, say all 1s from offset 0 to 16.
2. Truncate the file to a smaller size, say 8 bytes.
3. Write new bytes (say 2s) from an offset past the original size of the
file, say at offset 20, for 4 bytes. This is supposed to create a "hole"
in the file, meaning that the bytes from offset 8 (where it was truncated
above) up to the new write at offset 20, should all be 0s (zeros).
4. Flush all caches using "echo 3 > /proc/sys/vm/drop_caches" (or unmount
and remount) the f/s.
5. Check the content of the file. It is wrong. The 1s that used to be
between bytes 9 and 16, before the truncation, have REAPPEARED (they should
be 0s).
We wrote a script and helper C program to reproduce the bug
(reproduce_jffs2_write_begin_issue.sh, write_file.c, and Makefile). We can
make them available to anyone.
The above example is shown when writing a small file within the same first
page. But the bug happens for larger files, as long as steps 1, 2, and 3
above all happen within the same page.
The problem was traced to the jffs2_write_begin code, where it goes into an
'if' statement intended to handle writes past the current EOF (i.e., writes
that may create a hole). The code computes a 'pageofs' that is the floor
of the write position (pos), aligned to the page size boundary. In other
words, 'pageofs' will never be larger than 'pos'. The code then sets the
internal jffs2_raw_inode->isize to the size of max(current inode size,
pageofs) but that is wrong: the new file size should be the 'pos', which is
larger than both the current inode size and pageofs.
Similarly, the code incorrectly sets the internal jffs2_raw_inode->dsize to
the difference between the pageofs minus current inode size; instead it
should be the current pos minus the current inode size. Finally,
inode->i_size was also set incorrectly.
The patch below fixes this bug. The bug was discovered using a new tool
for finding f/s bugs using model checking, called MCFS (Model Checking File
Systems).
Signed-off-by: Yifei Liu <yifeliu@cs.stonybrook.edu>
Signed-off-by: Erez Zadok <ezk@cs.stonybrook.edu>
Signed-off-by: Manish Adkar <madkar@cs.stonybrook.edu>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
