The sensor's clock is enabled and disabled outside of the probe and
disable function. Moving the corresponding action in the
hisi_thermal_setup() and hisi_thermal_disable_sensor(), factors out
some lines of code and makes the code more symmetric.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org> # hikey6220
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The mutex is used to protect against writes in the configuration register.
That happens at probe time, with no possible race yet.
Then when the module is unloaded and at suspend/resume.
When the module is unloaded, it is an userspace operation, thus via a process.
Suspending the system goes through the freezer to suspend all the tasks
synchronously before continuing. So it is not possible to hit the suspend ops
in this driver while we are unloading it.
The resume is the same situation than the probe.
In other words, even if there are several places where we write the
configuration register, there is no situation where we can write it at the same
time, so far as I can judge
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The presence of the thermal data pointer in the sensor structure has the unique
purpose of accessing the thermal data in the interrupt handler.
The sensor pointer is passed when registering the interrupt handler, replace the
cookie by the thermal data pointer, so the back pointer is no longer needed.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no point to specify the temperature as long variable, the int is
enough.
Replace all long variables to int, so making the code consistent.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The sensor is all setup, bind, resetted, acked, etc... every single second.
That was the way to workaround a problem with the interrupt bouncing again and
again.
With the following changes, we fix all in one:
- Do the setup, one time, at probe time
- Add the IRQF_ONESHOT, ack the interrupt in the threaded handler
- Remove the interrupt handler
- Set the correct value for the LAG register
- Remove all the irq_enabled stuff in the code as the interruption
handling is fixed
- Remove the 3ms delay
- Reorder the initialization routine to be in the right order
It ends up to a nicer code and more efficient, the 3-5ms delay is removed from
the get_temp() path.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The TEMP0_CFG configuration register contains different field to set up the
temperature controller. However in the code, nothing prevents a setup to
overwrite the previous one: eg. writing the hdak value overwrites the sensor
selection, the sensor selection overwrites the hdak value.
In order to prevent such thing, use a regmap-like mechanism by reading the
value before, set the corresponding bits and write the result.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Hopefully, the function name can help to clarify the semantic of the operations
when writing in the register.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The threaded interrupt inspect the sensors structure to look in the temp
threshold field, but this field is read-only in all the code, except in the
probe function before the threaded interrupt is set. In other words there
is not race window in the threaded interrupt when reading the field value.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The DT specifies a threshold of 65000, we setup the register with a value in
the temperature resolution for the controller, 64656.
When we reach 64656, the interrupt fires, the interrupt is disabled. Then the
irq thread runs and calls thermal_zone_device_update() which will call in turn
hisi_thermal_get_temp().
The function will look if the temperature decreased, assuming it was more than
65000, but that is not the case because the current temperature is 64656
(because of the rounding when setting the threshold). This condition being
true, we re-enable the interrupt which fires immediately after exiting the irq
thread. That happens again and again until the temperature goes to more than
65000.
Potentially, there is here an interrupt storm if the temperature stabilizes at
this temperature. A very unlikely case but possible.
In any case, it does not make sense to handle dozens of alarm interrupt for
nothing.
Fix this by rounding the threshold value to the controller resolution so the
check against the threshold is consistent with the one set in the controller.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The step and the base temperature are fixed values, we can simplify the
computation by converting the base temperature to milli celsius and use a
pre-computed step value. That saves us a lot of mult + div for nothing at
runtime.
Take also the opportunity to change the function names to be consistent with
the rest of the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The threaded interrupt for the alarm interrupt is requested before the
temperature controller is setup. This one can fire an interrupt immediately
leading to a kernel panic as the sensor data is not initialized.
In order to prevent that, move the threaded irq after the Tsensor is setup.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
By essence, the tsensor does not really support multiple sensor at the same
time. It allows to set a sensor and use it to get the temperature, another
sensor could be switched but with a delay of 3-5ms. It is difficult to read
simultaneously several sensors without a big delay.
Today, just one sensor is used, it is not necessary to deal with multiple
sensors in the code. Remove them and if it is needed in the future add them
on top of a code which will be clean up in the meantime.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Wangtao (Kevin, Kirin) <kevin.wangtao@hisilicon.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The interrupt for the temperature threshold is not enabled at the end of the
probe function, enable it after the setup is complete.
On the other side, the irq_enabled is not correctly set as we are checking if
the interrupt is masked where 'yes' means irq_enabled=false.
irq_get_irqchip_state(data->irq, IRQCHIP_STATE_MASKED,
&data->irq_enabled);
As we are always enabling the interrupt, it is pointless to check if
the interrupt is masked or not, just set irq_enabled to 'true'.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
While debugging some PM issues and trying to remove all the loaded modules, I ran
across the following when unloading ti-soc-thermal:
Unable to handle kernel NULL pointer dereference at virtual address 000000b4
...
[<c08db340>] (kobject_put) from [<bf28954c>] (ti_thermal_unregister_cpu_cooling+0x20/0x28 [ti_soc_thermal])
[<bf28954c>] (ti_thermal_unregister_cpu_cooling [ti_soc_thermal]) from [<bf287c88>] (ti_bandgap_remove+0x3c/0x104 [ti_soc_thermal])
[<bf287c88>] (ti_bandgap_remove [ti_soc_thermal]) from [<c0610d48>] (platform_drv_remove+0x24/0x3c)
[<c0610d48>] (platform_drv_remove) from [<c060f114>] (device_release_driver_internal+0x160/0x208)
[<c060f114>] (device_release_driver_internal) from [<c060f200>] (driver_detach+0x38/0x6c)
[<c060f200>] (driver_detach) from [<c060e2d4>] (bus_remove_driver+0x4c/0xa0)
[<c060e2d4>] (bus_remove_driver) from [<c01f2370>] (SyS_delete_module+0x168/0x238)
[<c01f2370>] (SyS_delete_module) from [<c0108240>] (ret_fast_syscall+0x0/0x28)
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The initialization sequence for H3 (r8a7795) ES1.x and ES2.0 is
different. H3 ES2.0 and later uses the same sequence as M3 (r8a7796)
ES1.0. Fix this by not looking at compatible strings and instead
defaulting to the r8a7796 initialization sequence and use
soc_device_match() to check for H3 ES1.x.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The dev pointer is going through a null check after a dereference.
So this patch removes that useless check since the driver does not
pass a null dev pointer in any case.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Moving the bcm2835 thermal driver to the broadcom directory prevented it
from getting enabled for arm64 builds, since the broadcom directory is only
available when 32-bit specific ARCH_BCM is set.
Fix this by enabling the Broadcom menu for ARCH_BCM or ARCH_BCM2835.
Fixes: 6892cf07e7 ("thermal: bcm2835: move to the broadcom subdirectory")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Allen Wild <allenwild93@gmail.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The fix 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
uncovered another bug in the Marvell PHY driver, which broke the
Marvell OpenRD platform. It relies on the bootloader configuring the
RGMII delays and does not specify a phy-mode in its device tree. The
PHY driver should only configure RGMII delays if the phy mode
indicates it is using RGMII. Without anything in device tree, the
mv643xx Ethernet driver defaults to GMII.
Fixes: 5987feb38a ("net: phy: marvell: logical vs bitwise OR typo")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
The most important here is the security vulnerabitility fix for
ath10k.
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
single nouveau regression fix.
* 'linux-4.14' of git://github.com/skeggsb/linux:
drm/nouveau/kms/nv50: use the correct state for base channel notifier setup
Pull Rockchip clk drivers updates from Heiko Stuebner:
- new clock ids for rk3188 and rk3368
- removal of a superfluous memory allocation error message
* tag 'v4.15-rockchip-clk-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: use new cif/vdpu clock ids on rk3188
clk: rockchip: export clock pclk_efuse_256 for RK3368 SoCs
clk: rockchip: add more rk3188 graphics clock ids
clk: rockchip: add clock id for PCLK_EFUSE256 of RK3368 SoCs
clk: rockchip: Remove superfluous error message in rockchip_clk_register_cpuclk()
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for the second display unit clock on RZ/G1E,
- Add git repository to MAINTAINERS,
- Add suspend/resume support for R-Car Gen3 CPG/MSSR,
- Small fixes and cleanups.
* tag 'clk-renesas-for-v4.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: rcar-gen3: Restore R clock during resume
clk: renesas: rcar-gen3: Restore SDHI clocks during resume
clk: renesas: div6: Restore clock state during resume
clk: renesas: cpg-mssr: Add support to restore core clocks during resume
clk: renesas: cpg-mssr: Restore module clocks during resume
MAINTAINERS: Add git repository to Renesas clock driver section
clk: renesas: cpg-mssr: Add du1 clock to R8A7745
clk: renesas: rz: clk-rz is meant for RZ/A1
clk: renesas: r8a77995: Correct parent clock of INTC-AP
clk: renesas: r8a7796: Correct parent clock of INTC-AP
clk: renesas: r8a7795: Correct parent clock of INTC-AP
Pull Amlogic clock driver updates from Neil Armstrong:
- Addition of Video Processing Unit VPU and VAPB clocks
* tag 'meson-clk-for-4.15' of git://github.com/baylibre/clk-meson:
clk: meson: gxbb: Add VPU and VAPB clocks data
clk: meson: gxbb: Add VPU and VAPB clockids
Pull clockevent updates from Daniel Lezcano:
- Improve the generic clockevents dependency by factoring out the option
in the Kconfig menu option (Arnd Bergmann)
- Add missing "\n" in pr_err messages for fttmr010, owl and rockchip
(Arvind Yadav)
- Add missing timer_of_exit function to rollback timer_of_init (Benjamin
Gaignard)
- Fix path and add bindings to timers (Daniel Lezcano)
- Cleanup and remove support for renesas,cmt-32* (Geert Uytterhoeven)
- Add support for separate R-Car Gen2 (Magnus Damm)
- Fix DEFINE_PER_CPU length definition to prevent warning at expansion
time for the arm_arch_timer (Mark Rutland)
- Remove pointless irq_save,restore in an already irq-disabled callback
and add a shortcut optimization for the local cpu on mips-gic-timer
(Matt Redfearn)
Pull power management commit reverts from Rafael Wysocki:
"Since Geert reports additional problems with my PM QoS fix from the
last week that have not been addressed by the most recent fixup on top
of it, they both should better be reverted now and let's fix the
original issue properly in 4.15.
This reverts two recent PM QoS commits one of which introduced
multiple problems and the other one fixed some, but not all of them
(Rafael Wysocki)"
* tag 'pm-reverts-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / QoS: Fix device resume latency PM QoS"
Revert "PM / QoS: Fix default runtime_pm device resume latency"
The function for byteswapping the data send to/from atombios was buggy for
num_bytes not divisible by four. The function must be aware of the fact
that after byte-swapping the u32 units, valid bytes might end up after the
num_bytes boundary.
This patch was tested on kernel 3.12 and allowed us to sucesfully use
DisplayPort on and Radeon SI card. Namely it fixed the link training and
EDID readout.
The function is patched both in radeon and amd drivers, since the functions
and the fixes are identical.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Pull timekeeping updates from John Stultz:
- More y2038 work from Arnd Bergmann
- A new mechanism to allow RTC drivers to specify the resolution of the
RTC so the suspend/resume code can make informed decisions whether to
inject the suspended time or not in case of fast suspend/resume cycles.
Pull Allwinner clock driver updates from Maxime Ripard:
- Addition of sigma/delta modulation for the audio PLLs on the newer SoCs
- A83t Display clocks supports
- minor fixes that didn't have any impact on current features
* tag 'sunxi-clk-for-4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: sun4i: Export video PLLs
clk: sunxi-ng: Add A83T display clocks
clk: sunxi-ng: sun8i: a23: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun6i: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun5i: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun4i: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun8i: h3: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: nm: Add support for sigma-delta modulation
clk: sunxi-ng: Add sigma-delta modulation support
clk: sunxi-ng: nm: Check if requested rate is supported by fractional clock
clk: sunxi-ng: sun5i: Fix bit offset of audio PLL post-divider
clk: sunxi-ng: a83t: Fix invalid csi-mclk mux offset
clk: sunxi-ng: sun6i: Rename HDMI DDC clock to avoid name collision
clk: sunxi-ng: sun6i: Export video PLLs
clk: sunxi-ng: Implement reset control status readback
clk: sunxi-ng: Fix missing CLK_SET_RATE_PARENT in ccu-sun4i-a10.c
clk: sunxi-ng: add CLK_SET_RATE_PARENT flag to H3 GPU clock
clk: sunxi-ng: add CLK_SET_RATE_UNGATE to all H3 PLLs
The Lenovo Yoga 920-13IKB does not have a hw rfkill switch, and trying
to read the hw rfkill switch through the ideapad module causes it to
always report as blocked.
This commit adds the Lenovo Yoga 920-13IKB to the no_hw_rfkill dmi list,
fixing the WiFI breakage.
Signed-off-by: Philipp Hug <philipp@hug.cx>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
