The 5380 drivers only support asynchronous transfers and the 5380
controllers only have narrow busses. Hence, the core driver will reject
any SDTR and WDTR messages from target devices. Don't log this, it's
expected behaviour. Also, fix the off-by-one array indices in the
arguments to scmd_printk().
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cxlflash driver tracks process IDs alongside contexts to validate
context ownership. Currently, the process IDs are derived by directly
accessing values from the 'current' task pointer. While this method of
access is fine for the current process, it is incorrect when the parent
process ID is needed as the access requires serialization.
To address the incorrect issue and provide a consistent means of
deriving the process ID within the cxlflash driver, use the task
accessors defined linux/sched.h.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, all adapters that cxlflash supports must have WWPN VPD
keywords to complete configuration. This was required as cards with
external FC ports needed to be programmed with WWPNs.
Newer supported cards do not have an external FC interface and therefore
do not require WWPN. To support backwards compatibility, these devices
have included 'dummy' WWPN VPD with WWPN values of zero. This however
places a dependency that all future cards have WWPN VPD, which may not
always be the case.
Allow for cards to not have WWPN, designating which cards are expected
to have it in order to configure properly.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The existing write same routine within the cxlflash driver uses a
statically defined value for the maximum write same transfer length.
While this is close to the value reflected by the original device that
was supported by cxlflash, newer devices are capable of much larger
lengths. Supporting what the device is capable of offers substantial
performance improvement as the scrub routine within cxlflash operates on
'chunk size' units (256MB with a 4K sector size).
Instead of a #define, use the write same maximum length that is stored
in the block layer in units of 512 byte sectors. This value is initially
determined from the block limits VPD page during device discovery and
can also be manipulated from sysfs. As a general cleanup, designate the
timeout used when executing the write same command as constant.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for processing AXI bus fatal errors.
If AXI bus fatal error happen, do controller reset to recover.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CQ event is handled in tasklet context, and it could be delayed if
the system loading is high.
It is possible to run into some problems when executing a host reset
when cq_tasklet_vx_hw() is being executed.
So, prior to host reset, execute tasklet_kill() to ensure that all CQ
tasklets are complete.
Besides, as the function hisi_sas_wait_tasklets_done() is added to do
tasklet_kill(), this patch refactors some code where tasklet_kill() is
used.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use completion to wait on ITCT CLR interrupt finishing before
processing other things when freeing a device.
This is safer than the pre-existing process of polling the register.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add init code of hisi_hba->rst_work for v3 hw. Because v3 hw also need
it to recover controller when some hw errors occurs.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Realise get_events() to add DFX feature for v3 hw. Just like v2 hw, We
support the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should check register PHY_STATE when getting the bitmap of a
wideport, as, if the PHY is not ready, the value of register
PHY_PORT_NUM_MA is not valid.
V2 hw has done this check, and v3 hw should do this check too.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove V4L2 async re-probing support. The re-probing support has been
there to support cases where the sub-devices require resources provided by
the main driver's hardware to function, such as clocks.
Reprobing has allowed unbinding and again binding the main driver without
explicitly unbinding the sub-device drivers. This is certainly not a
common need, and the responsibility will be the user's going forward.
An alternative could have been to introduce notifier specific locks.
Considering the complexity of the re-probing and that it isn't really a
solution to a problem but a workaround, remove re-probing instead.
If there is a need to support the clock provider unregister/register cycle
while keeping the clock references in the consumers in the future, this
should be implemented in the clock framework instead, not in V4L2.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The test_pattern_menu[] array has two valid items and a null terminated
item. So the control's maximum value which is passed to
v4l2_ctrl_new_std_menu_items() should be one. However,
'ARRAY_SIZE(test_pattern_menu) - 1' is actually passed and it's not
correct.
Fix it by removing unnecessary terminated entry and let the correct
control's maximum value be passed to v4l2_ctrl_new_std_menu_items().
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c65399 ("mtd: Add panic_write for NAND flashes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
ath.git fixes for 4.14. Major changes:
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
Send PVCALLS_RELEASE to the backend and wait for a reply. Take both
in_mutex and out_mutex to avoid concurrent accesses. Then, free the
socket.
For passive sockets, check whether we have already pre-allocated an
active socket for the purpose of being accepted. If so, free that as
well.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
For active sockets, check the indexes and use the inflight_conn_req
waitqueue to wait.
For passive sockets if an accept is outstanding
(PVCALLS_FLAG_ACCEPT_INFLIGHT), check if it has been answered by looking
at bedata->rsp[req_id]. If so, return POLLIN. Otherwise use the
inflight_accept_req waitqueue.
If no accepts are inflight, send PVCALLS_POLL to the backend. If we have
outstanding POLL requests awaiting for a response use the inflight_req
waitqueue: inflight_req is awaken when a new response is received; on
wakeup we check whether the POLL response is arrived by looking at the
PVCALLS_FLAG_POLL_RET flag. We set the flag from
pvcalls_front_event_handler, if the response was for a POLL command.
In pvcalls_front_event_handler, get the struct sock_mapping from the
poll id (we previously converted struct sock_mapping* to uintptr_t and
used it as id).
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Implement recvmsg by copying data from the "in" ring. If not enough data
is available and the recvmsg call is blocking, then wait on the
inflight_conn_req waitqueue. Take the active socket in_mutex so that
only one function can access the ring at any given time.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Send data to an active socket by copying data to the "out" ring. Take
the active socket out_mutex so that only one function can access the
ring at any given time.
If not enough room is available on the ring, rather than returning
immediately or sleep-waiting, spin for up to 5000 cycles. This small
optimization turns out to improve performance significantly.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Introduce a waitqueue to allow only one outstanding accept command at
any given time and to implement polling on the passive socket. Introduce
a flags field to keep track of in-flight accept and poll commands.
Send PVCALLS_ACCEPT to the backend. Allocate a new active socket. Make
sure that only one accept command is executed at any given time by
setting PVCALLS_FLAG_ACCEPT_INFLIGHT and waiting on the
inflight_accept_req waitqueue.
Convert the new struct sock_mapping pointer into an uintptr_t and use it
as id for the new socket to pass to the backend.
Check if the accept call is non-blocking: in that case after sending the
ACCEPT command to the backend store the sock_mapping pointer of the new
struct and the inflight req_id then return -EAGAIN (which will respond
only when there is something to accept). Next time accept is called,
we'll check if the ACCEPT command has been answered, if so we'll pick up
where we left off, otherwise we return -EAGAIN again.
Note that, differently from the other commands, we can use
wait_event_interruptible (instead of wait_event) in the case of accept
as we are able to track the req_id of the ACCEPT response that we are
waiting.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Send PVCALLS_CONNECT to the backend. Allocate a new ring and evtchn for
the active socket.
Introduce fields in struct sock_mapping to keep track of active sockets.
Introduce a waitqueue to allow the frontend to wait on data coming from
the backend on the active socket (recvmsg command).
Two mutexes (one of reads and one for writes) will be used to protect
the active socket in and out rings from concurrent accesses.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Send a PVCALLS_SOCKET command to the backend, use the masked
req_prod_pvt as req_id. This way, req_id is guaranteed to be between 0
and PVCALLS_NR_REQ_PER_RING. We already have a slot in the rsp array
ready for the response, and there cannot be two outstanding responses
with the same req_id.
Wait for the response by waiting on the inflight_req waitqueue and
check for the req_id field in rsp[req_id]. Use atomic accesses and
barriers to read the field. Note that the barriers are simple smp
barriers (as opposed to virt barriers) because they are for internal
frontend synchronization, not frontend<->backend communication.
Once a response is received, clear the corresponding rsp slot by setting
req_id to PVCALLS_INVALID_ID. Note that PVCALLS_INVALID_ID is invalid
only from the frontend point of view. It is not part of the PVCalls
protocol.
pvcalls_front_event_handler is in charge of copying responses from the
ring to the appropriate rsp slot. It is done by copying the body of the
response first, then by copying req_id atomically. After the copies,
wake up anybody waiting on waitqueue.
socket_lock protects accesses to the ring.
Convert the pointer to sock_mapping into an uintptr_t and use it as
id for the new socket to pass to the backend. The struct will be fully
initialized later on connect or bind.
sock->sk->sk_send_head is not used for ip sockets: reuse the field to
store a pointer to the struct sock_mapping corresponding to the socket.
This way, we can easily get the struct sock_mapping from the struct
socket.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Implement the probe function for the pvcalls frontend. Read the
supported versions, max-page-order and function-calls nodes from
xenstore.
Only one frontend<->backend connection is supported at any given time
for a guest. Store the active frontend device to a static pointer.
Introduce a stub functions for the event handler.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Introduce a data structure named pvcalls_bedata. It contains pointers to
the command ring, the event channel, a list of active sockets and a list
of passive sockets. Lists accesses are protected by a spin_lock.
Introduce a waitqueue to allow waiting for a response on commands sent
to the backend.
Introduce an array of struct xen_pvcalls_response to store commands
responses.
Introduce a new struct sock_mapping to keep track of sockets. In this
patch the struct sock_mapping is minimal, the fields will be added by
the next patches.
pvcalls_refcount is used to keep count of the outstanding pvcalls users.
Only remove connections once the refcount is zero.
Implement pvcalls frontend removal function. Go through the list of
active and passive sockets and free them all, one at a time.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Hyper-V allows the guest to report panic and the guest can pass additional
information. All this is logged on the host. Currently Linux is passing back
information that is not particularly useful. Make the following changes:
1. Windows uses crash MSR P0 to report bugcheck code. Follow the same
convention for Linux as well.
2. It will be useful to know the gust ID of the Linux guest that has
paniced. Pass back this information.
These changes will help in better supporting Linux on Hyper-V
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When investigating performance, it is useful to be able to look at
the number of host and guest events per-channel. This is equivalent
to per-device interrupt statistics.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fd9c963c56 ("gpio: mb86s70: Return error if requesting an
already assigned gpio") adds code that infers from the state of the
GPIO Pin Function Register (PFR) whether a GPIO has been assigned
already. This assumes that the pin functions are set to 'peripheral'
when the driver is loaded, which is not guaranteed. Also, the GPIO
layer is perfectly capable of keeping track of which GPIOs have been
assigned already, so we shouldn't need this check in the first place.
This reverts commit fd9c963c56.
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to reuse this driver for the Socionext Synquacer SC2A11 SoC,
which inherited this IP from Fujitsu, remove the ARCH_MB86S7X Kconfig
dependency, and revert the changes that prevent it from being built as
a module.
This reverts commits d65aa4b67b and
d5610e514e.
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[Folded in module_platform_driver() fixup]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current edge both type gpio irqs which need to swap polarity in each
interrupt are not supported, this patch adds edge both type gpio irq
support.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On error, kthread_create() returns an errno-encoded pointer, not NULL.
The routine qla2x00_probe_one() detects the error case and jumps to
probe_failed, but has already assigned the return value from
kthread_create() to ha->dpc_thread. Then probe_failed checks to see if
ha->dpc_thread is not NULL before doing cleanup on it. Since in the
error case this is also not NULL, it ends up trying to access an invalid
task pointer.
Solution is to assign NULL to ha->dpc_thread in the error path to avoid
kthread cleanup in that case.
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make use of the swap macro and remove unnecessary variable tmp_frame.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix the clock ID to do the runtime pm should be ISC_ISPCK,
instead of ISC_MCK in clk_prepare(), clk_unprepare() and
isc_clk_is_enabled().
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pointer pix is being initialized to a value and a little later
being assigned the same value again. Remove the initial assignment to
avoid a duplicate assignment. Cleans up the clang warning:
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:726:26: warning: Value
stored to 'pix' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable j is being set to zero before a loop and also
immediately inside the loop and is not used after the loop.
Hence the first assignment is redundant and can be removed.
Cleans up clang warning:
drivers/media/usb/gspca/gspca.c:1078:2: warning: Value stored
to 'j' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable index is set to zero and then set to zero again
a few lines later in a for loop initialization. Remove the
redundant setting of index to zero. Cleans up the clang
warning:
drivers/media/usb/dvb-usb-v2/mxl111sf-i2c.c:519:3: warning: Value
stored to 'index' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable freq is initialized to f->frequency however this value
is never read and freq is later updated; hence the initialization
is redundant and can be removed.
Cleans up clang warning:
drivers/media/radio/radio-raremono.c:257:6: warning: Value stored
to 'freq' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
