This commit corrects problems with the previous wake implementation
by implementing suspend and resume power management operations and
the driver shutdown operation.
Wake masks are used to keep track of which GPIO should wake the
device. On suspend the GPIO state is saved and the possible wakeup
sources are explicitly unmasked in the hardware. Non-wakeup sources
are explicitly masked so IRQCHIP_MASK_ON_SUSPEND is no longer
necessary. The saved state of the GPIO is restored upon resume.
It is important not to write to the GPIO status register since this
has the effect of clearing bits. The status register is explicitly
removed from the register save and restore to ensure this.
The shutdown operation allows the hardware to be put into the same
quiesced state as the suspend operation and removes the need for
the reboot notifier.
Unfortunately, there appears to be some confusion about whether
a pending disabled wake interrupt should wake the system. If a wake
capable interrupt is disabled using the default "lazy disable"
behavior and it is triggered before the suspend_device_irq call
the interrupt hardware will be acknowledged by mask_ack_irq and the
IRQS_PENDING flag is added to its state. However, the IRQS_PENDING
flag of wake interrupts is not checked to prevent the transition to
suspend and the hardware has been acked which prevents its wakeup.
If the lazy disabled interrupt is triggered after the call to
suspend_device_irqs then the wakeup logic will abort the suspend.
The irq_disable method is defined by this GPIO driver to prevent
lazy disable so that the pending hardware state remains asserted
allowing the hardware to wake and providing a consistent behavior.
In addition, the IRQ_DISABLE_UNLAZY flag is set for the non-wake
parent interrupt as a convenience to prevent the need to add code
to the brcmstb_gpio_irq_handler to support "lazy disable" of the
non-wake parent interrupt when it is disabled during suspend and
resume. Chained interrupt parents are not normally disabled, but
these GPIO devices have different parent interrupts for wake and
non-wake handling. It is convenient to mask the non-wake parent
when suspending to preserve the hardware state for proper wakeup
accounting when the driver is resumed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOLIB IRQ chip helpers were very appealing, but badly broke
the 1:1 mapping between a GPIO controller's device_node and its
interrupt domain.
When another device-tree node references a GPIO device as its
interrupt parent, the irq_create_of_mapping() function looks for
the irq domain of the GPIO device and since all bank irq domains
reference the same GPIO device node it always resolves to the irq
domain of the first bank regardless of which bank the number of
the GPIO should resolve. This domain can only map hwirq numbers
0-31 so interrupts on GPIO above that can't be mapped by the
device-tree.
This commit effectively reverts the patch from Gregory Fong [1]
that was accepted upstream and replaces it with a consolidated
irq domain implementation with one larger interrupt domain per
GPIO controller instance spanning multiple GPIO banks based on
an earlier patch [2] also submitted by Gregory Fong.
[1] https://patchwork.kernel.org/patch/6921561/
[2] https://patchwork.kernel.org/patch/6347811/
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/media/platform/atmel/atmel-isc.c: In function 'isc_async_complete':
drivers/media/platform/atmel/atmel-isc.c:1900:28: warning: variable 'sd_entity' set but not used [-Wunused-but-set-variable]
struct isc_subdev_entity *sd_entity;
^~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This commit corrects a bug when configuring the GPIO hardware for
IRQ_TYPE_LEVEL_LOW and IRQ_TYPE_LEVEL_HIGH interrupt types. The
hardware is now correctly configured to support those types.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reading and writing the gpio bank status register each time a pending
interrupt bit is serviced could cause new pending bits to be cleared
without servicing the associated interrupts.
By using the handle_level_irq flow instead of the handle_simple_irq
flow we get proper handling of interrupt masking as well as acking
of interrupts. The irq_ack method is added to support this.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The basic memory-mapped GPIO controller lock must be released
before calling the registered GPIO interrupt handlers to allow
the interrupt handlers to access the hardware.
Examples of why a GPIO interrupt handler might want to access
the GPIO hardware include an interrupt that is configured to
trigger on rising and falling edges that needs to read the
current level of the input to know how to respond, or an
interrupt that causes a change in a GPIO output in the same
bank. If the lock is not released before enterring the handler
the hardware accesses will deadlock when they attempt to grab
the lock.
Since the lock is only needed to protect the calculation of
unmasked pending interrupts create a dedicated function to
perform this and hide the complexity.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit allows a wakeup parent interrupt to be shared between
instances.
It also removes the redundant can_wake member of the private data
structure by using whether the parent_wake_irq has been defined to
indicate that the GPIO device can wake.
Fixes: 19a7b6940b ("gpio: brcmstb: Add interrupt and wakeup source support")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is handled by the mmc-pwrseq-emmc driver, which controls
an eMMC hardware reset via a GPIO line.
Remove it from the function pin-mux settings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rk3288 also has one function that can be routed to one of two pins,
the hdmi cec functionality can use either gpio7c0 or gpio7c7.
So add the route switching support for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Cedar Fork PCH is the successor of Intel Denverton PCH but it is
based on the newer GPIO/pinctrl hardware block. Add a new pinctrl/GPIO
driver to support it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO blocks have the interrupt status (GPI_IS) offset different
than it normally is, so make it configurable. If no offset is specified
we use the default.
While there remove two unused constants from the core driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a jump target so that a bit of exception handling can be better reused
at the end of this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using devm_ioremap_resource() has several advantages over devm_ioremap():
- it checks the passed resource's validity;
- it calls devm_request_mem_region() to check for the resource overlap;
- it prints an error message in case of error.
We can call devm_ioremap_resource() instead of devm_ioremap_nocache()
as ioremap() and ioremap_nocache() are implemented identically on ARM.
Doing this saves 2 LoCs and 80 bytes (AArch64 gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement Fintek f81534 break on/off with LCR register.
It's the same with 16550A LCR register layout.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The strict mode should always have been enabled on our driver, and leaving
it unchecked just makes it harder to find a migration path as time passes.
Let's enable it by default now so that hopefully the new SoCs should be
safe.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Old pinctrl drivers will need to disable strict mode for various reasons,
among which:
- Some DT will still have a pinctrl group for each GPIO used, which will
be rejected by pin_request. While we could remove those nodes, we still
have to deal with old DTs.
- Some GPIOs on these boards need to have their pin configuration changed
(for bias or current), and there's no clear migration path
Let's disable the strict mode on those SoCs so that there's no breakage.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our pinctrl device should have had strict set all along. However, it wasn't
the case, and most of our old device trees also have a pinctrl group in
addition to the GPIOs properties, which mean that we can't really turn it
on now.
All our new SoCs don't have that group, so we should still enable that mode
on the newer one though.
In order to enable it by default, add a flag that will allow to disable
that mode that should be set by pinctrl drivers that cannot be migrated.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The F81532/534 without this patch will hang-up on data overrun.
It's caused by enable LSR interrupt in IER by default and occur data
overrun, the chip will busy for process LSR interrupt but not read LSR
internally. It will not responed for USB control endpoint0 and we can't
read LSR from driver in this situration.
So we'll disable the LSR interrupt in probe() and submit the LSR worker to
clear LSR state when reported LSR error bit with bulk-in data in
f81534_process_per_serial_block().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Intents can vary in size, try to find the best fitting remote intent
instead of first fit when sending a message to the remote proc.
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The base intents prequeued during channel creation may not satisfy a
channel's throughput requirement. Add support for intents dt-binding to
allow channels to specify the size and amount of intents to prequeue
during endpoint announcement.
Signed-off-by: Chris Lew <clew@codeaurora.org>
[bjorn: Altered how defaults are expressed]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The "intent_req_comp" variable is used without initialization which
results in NULL pointer dereference in qcom_glink_request_intent().
we need to initialize the completion variable before using it.
Fixes: 27b9c5b66b ("rpmsg: glink: Request for intents when unavailable")
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch add support for mss boot on msm8996. Major changes
include initializing mss rproc for msm8996, making appropriate
change for executing mss reset sequence etc.
Tested-and-acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
MSS proc on msm8996 can not access fw loaded region without stage
second translation of memory pages where mpss image are loaded.
This patch in order to enable mss boot on msm8996 invoke scm call
to switch or share ownership between apps and modem.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
[bjorn: Corrected error path in q6v5_start()]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch refactor code to first load all firmware blobs
and then update modem proc to authenticate and boot fw.
Tested-and-acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Two different processors on a SOC need to switch memory ownership
during load/unload. To enable this, second level memory map table
need to be updated, which is done by secure layer.
This patch adds the interface for making secure monitor call for
memory ownership switching request.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
[bjorn: Minor style and kerneldoc updates]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull Samsung clk driver updates from Sylwester Nawrocki:
- An addition of separate driver for the Exynos 4412 ISP CMU, needed
to model and properly handle the clock controller's dependencies
on the ISP power domain.
- Adding __maybe_unused attributes to the exynos5433_cmu_{suspend,
resume} ops to suppress compiler warnings with CONFIG_PM disabled.
* tag 'clk-v4.15-exynos-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: Add a separate driver for Exynos4412 ISP clocks
clk: samsung: Add dt bindings for Exynos4412 ISP clock controller
clk: samsung: Instantiate Exynos4412 ISP clocks only when available
clk: samsung: exynos5433: mark PM functions as __maybe_unused
ntp is currently hardwired to try and call the rtc set when wall clock
tv_nsec is 0.5 seconds. This historical behaviour works well with certain
PC RTCs, but is not universal to all rtc hardware.
Change how this works by introducing the driver specific concept of
set_offset_nsec, the delay between current wall clock time and the target
time to set (with a 0 tv_nsecs).
For x86-style CMOS set_offset_nsec should be -0.5 s which causes the last
second to be written 0.5 s after it has started.
For compat with the old rtc_set_ntp_time, the value is defaulted to
+ 0.5 s, which causes the next second to be written 0.5s before it starts,
as things were before this patch.
Testing shows many non-x86 RTCs would like set_offset_nsec ~= 0,
so ultimately each RTC driver should set the set_offset_nsec according
to its needs, and non x86 architectures should stop using
update_persistent_clock64 in order to access this feature.
Future patches will revise the drivers as needed.
Since CMOS and RTC now have very different handling they are split
into two dedicated code paths, sharing the support code, and ifdefs
are replaced with IS_ENABLED.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Miroslav Lichvar <mlichvar@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
mutex_destroy does nothing most of time, but it's better to call
it to make the code future proof and it also has some meaning
for like mutex debug.
As Coly pointed out in a previous review, bcache_exit() may not be
able to handle all the references properly if userspace registers
cache and backing devices right before bch_debug_init runs and
bch_debug_init failes later. So not exposing userspace interface
until everything is ready to avoid that issue.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, Cache missed IOs are identified by s->cache_miss, but actually,
there are many situations that missed IOs are not assigned a value for
s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO
(s->iop.bypass = 1), or the cache_bio allocate failed. In these situations,
it will go to out_put or out_submit, and s->cache_miss is null, which leads
bch_mark_cache_accounting() to treat this IO as a hit IO.
[ML: applied by 3-way merge]
Signed-off-by: tang.junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bucket_in_use is updated in gc thread which triggered by invalidating or
writing sectors_to_gc dirty data, It's a long interval. Therefore, when we
use it to compare with the threshold, it is often not timely, which leads
to inaccurate judgment and often results in bucket depletion.
We have send a patch before, by the means of updating bucket_in_use
periodically In gc thread, which Coly thought that would lead high
latency, In this patch, we add avail_nbuckets to record the count of
available buckets, and we calculate bucket_in_use when alloc or free
bucket in real time.
[edited by ML: eliminated some whitespace errors]
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable cached_dev.count is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When bcache does read I/Os, for example in writeback or writethrough mode,
if a read request on cache device is failed, bcache will try to recovery
the request by reading from cached device. If the data on cached device is
not synced with cache device, then requester will get a stale data.
For critical storage system like database, providing stale data from
recovery may result an application level data corruption, which is
unacceptible.
With this patch, for a failed read request in writeback or writethrough
mode, recovery a recoverable read request only happens when cache device
is clean. That is to say, all data on cached device is up to update.
For other cache modes in bcache, read request will never hit
cached_dev_read_error(), they don't need this patch.
Please note, because cache mode can be switched arbitrarily in run time, a
writethrough mode might be switched from a writeback mode. Therefore
checking dc->has_data in writethrough mode still makes sense.
Changelog:
V4: Fix parens error pointed by Michael Lyle.
v3: By response from Kent Oversteet, he thinks recovering stale data is a
bug to fix, and option to permit it is unnecessary. So this version
the sysfs file is removed.
v2: rename sysfs entry from allow_stale_data_on_failure to
allow_stale_data_on_failure, and fix the confusing commit log.
v1: initial patch posted.
[small change to patch comment spelling by mlyle]
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reported-by: Arne Wolf <awolf@lenovo.com>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Nix <nix@esperi.org.uk>
Cc: Kai Krakow <hurikhan77@gmail.com>
Cc: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: Junhui Tang <tang.junhui@zte.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The driver parameter num_user_contexts controls global behavior and
should not be modified by the driver.
This patch eliminates modification of num_user_contexts by using a
local variable to keep track of the value.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These are the use-cases where the pkey needs to be tested to see
if a packet needs to be dropped.
a) Check if pkey is not FULL_MGMT_P_KEY or LIM_MGMT_P_KEY,
drop the packet as it's not part of the management partition.
Self-originated packets are an exception.
b) If pkey index points to FULL_MGMT_P_KEY and LIM_MGMT_P_KEY is
in the table, the packet is coming from a management node,
and the receiving node is also a management node, so it is safe
for the packet to go through.
c) If pkey index points to FULL_MGMT_P_KEY and LIM_MGMT_P_KEY is
NOT in the table, drop the packet as LIM_MGMT_P_KEY should
always be in the pkey table. It could be a misconfiguration.
d) If pkey index points to LIM_MGMT_P_KEY and FULL_MGMT_P_KEY is
NOT in the table, it is safe for the packet to go through
since a non-management node is talking to another non-managment
node.
e) If pkey index points to LIM_MGMT_P_KEY and FULL_MGMT_P_KEY is in
the table, drop the packet because a non-management node is
talking to a management node, and it could be an attack.
For the implementation, these rules can be simplied to only checking
for (a) and (e). There's no need to check for rule (b) as
the packet doesn't need to be dropped. Rule (c) is not possible in
the driver as LIM_MGMT_P_KEY is always in the pkey table.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
__subn_get_opa_portinfo stores value returned by hfi1_get_ib_cfg() as
operational vls. hfi1_get_ib_cfg() returns vls_operational field in
hfi1_pportdata. The problem with this is that the value is always equal
to vls_supported field in hfi1_pportdata.
The logic to calculate operational_vls is to set value passed by FM
(in __subn_set_opa_portinfo routine). If no value is passed then
default value is stored in operational_vls.
Field actual_vls_operational is calculated on the basis of buffer
control table. Hence, modifying hfi1_get_ib_cfg() to return
actual_operational_vls when used with HFI1_IB_CFG_OP_VLS parameter
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Patel Jay P <jay.p.patel@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The handler for link init state (HLS_UP_INIT) notifies userspace
(update_statusp()) before enabling the device
(RCV_CTRL_RCV_PORT_ENABLE_SMASK) or setting the device state
(ppd->host_link_state). This causes a race condition where the
userspace thinks the interface is in the INIT state before the driver
has set that state.
Rework the code path to eliminate the race.
Delay setting the init state until after a HW settling period.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Per v1.6 of the NVDIMM_FAMILY_INTEL command set [1] some of the new
commands require rev-id 2. In addition to enabling ND_CMD_CALL for these
new function numbers, add a lookup table for revision-ids by family
and function number.
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface-V1.6.pdf
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Eliminate the partially duplicated DDI readout code from MST, and
instead just call intel_ddi_get_config(). As a nice bonus we get
more cross checking as intel_ddi_get_config() will populate
output_types based on the actual mode of the DDI port.
Additonally intel_ddi_get_config() must be changed to get the crtc
from the passed in crtc state rather than from the encoder->crtc link.
encoder->crtc really shouldn't be used anyway.
v2: Rebased on BXT MST latency_optim fix
Make intel_ddi_clock_get() static
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027193128.14483-7-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Pass an old crtc state to intel_ddi_post_disable() from the MST code.
Note that this crtc state won't necessaitly match the one that was
passed to intel_ddi_pre_enable() if the first stream to be enabled isn't
the last stream to be disabled. But this is fine since the states should
be identical in every important way. This does mean people frobbing
the DDI pre_enable/post_disable hooks have to pay attention in what
parts of the state they consult.
The alternative would be to inline the relevant code into the MST code.
That is actually what we used to do for pre_enable before
commit e081c8463a ("drm/i915: Remove duplicate DDI enabling logic
from MST path"). For post_disable we've always called the DDI hook.
v2: Pimp up the comments explaining the MST issues
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171027193128.14483-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
