[ Upstream commit 69f2c93463 ]
Commit 2dc0b46b5e ("libata: sata_down_spd_limit should return if
driver has not recorded sstatus speed") changed the behavior of
sata_down_spd_limit() to return doing nothing if a drive does not report
a current link speed, to avoid reducing the link speed to the lowest 1.5
Gbps speed.
However, the change assumed that a speed was recorded before probing
(e.g. before a suspend/resume) and set in link->sata_spd. This causes
problems with adapters/drives combination failing to establish a link
speed during probe autonegotiation. One example reported of this problem
is an mvebu adapter with a 3Gbps port-multiplier box: autonegotiation
fails, leaving no recorded link speed and no reported current link
speed. Probe retries also fail as no action is taken by sata_set_spd()
after each retry.
Fix this by returning early in sata_down_spd_limit() only if we do have
a recorded link speed, that is, if link->sata_spd is not 0. With this
fix, a failed probe not leading to a recorded link speed is retried at
the lower 1.5 Gbps speed, with the link speed potentially increased
later on the second revalidate of the device if the device reports
that it supports higher link speeds.
Reported-by: Marius Dinu <marius@psihoexpert.ro>
Fixes: 2dc0b46b5e ("libata: sata_down_spd_limit should return if driver has not recorded sstatus speed")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Marius Dinu <marius@psihoexpert.ro>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0553680f9 ]
The conclusion "j1939_session_deactivate() should be called with a
session ref-count of at least 2" is incorrect. In some concurrent
scenarios, j1939_session_deactivate can be called with the session
ref-count less than 2. But there is not any problem because it
will check the session active state before session putting in
j1939_session_deactivate_locked().
Here is the concurrent scenario of the problem reported by syzbot
and my reproduction log.
cpu0 cpu1
j1939_xtp_rx_eoma
j1939_xtp_rx_abort_one
j1939_session_get_by_addr [kref == 2]
j1939_session_get_by_addr [kref == 3]
j1939_session_deactivate [kref == 2]
j1939_session_put [kref == 1]
j1939_session_completed
j1939_session_deactivate
WARN_ON_ONCE(kref < 2)
=====================================================
WARNING: CPU: 1 PID: 21 at net/can/j1939/transport.c:1088 j1939_session_deactivate+0x5f/0x70
CPU: 1 PID: 21 Comm: ksoftirqd/1 Not tainted 5.14.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:j1939_session_deactivate+0x5f/0x70
Call Trace:
j1939_session_deactivate_activate_next+0x11/0x28
j1939_xtp_rx_eoma+0x12a/0x180
j1939_tp_recv+0x4a2/0x510
j1939_can_recv+0x226/0x380
can_rcv_filter+0xf8/0x220
can_receive+0x102/0x220
? process_backlog+0xf0/0x2c0
can_rcv+0x53/0xf0
__netif_receive_skb_one_core+0x67/0x90
? process_backlog+0x97/0x2c0
__netif_receive_skb+0x22/0x80
Fixes: 0c71437dd5 ("can: j1939: j1939_session_deactivate(): clarify lifetime of session object")
Reported-by: syzbot+9981a614060dcee6eeca@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20210906094200.95868-1-william.xuanziyang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afc2336f89 ]
The Meson G12A Internal PHY does not support standard IEEE MMD extended
register access, therefore add generic dummy stubs to fail the read and
write MMD calls. This is necessary to prevent the core PHY code from
erroneously believing that EEE is supported by this PHY even though this
PHY does not support EEE, as MMD register access returns all FFFFs.
Fixes: 5c3407abb3 ("net: phy: meson-gxl: add g12a support")
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Chris Healy <healych@amazon.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20230130231402.471493-1-cphealy@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b272bb558 ]
When using a xfrm interface in a bridged setup (the outgoing device is
bridged), the incoming packets in the xfrm interface are only tracked
in the outgoing direction.
$ brctl show
bridge name interfaces
br_eth1 eth1
$ conntrack -L
tcp 115 SYN_SENT src=192... dst=192... [UNREPLIED] ...
If br_netfilter is enabled, the first (encrypted) packet is received onR
eth1, conntrack hooks are called from br_netfilter emulation which
allocates nf_bridge info for this skb.
If the packet is for local machine, skb gets passed up the ip stack.
The skb passes through ip prerouting a second time. br_netfilter
ip_sabotage_in supresses the re-invocation of the hooks.
After this, skb gets decrypted in xfrm layer and appears in
network stack a second time (after decryption).
Then, ip_sabotage_in is called again and suppresses netfilter
hook invocation, even though the bridge layer never called them
for the plaintext incarnation of the packet.
Free the bridge info after the first suppression to avoid this.
I was unable to figure out where the regression comes from, as far as i
can see br_netfilter always had this problem; i did not expect that skb
is looped again with different headers.
Fixes: c4b0e771f9 ("netfilter: avoid using skb->nf_bridge directly")
Reported-and-tested-by: Wolfgang Nothdurft <wolfgang@linogate.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 721858823d ]
Theoretically the device might gone if its reference count drops to 0.
This might be the case when we try to find the first physical node of
the ACPI device. We need to keep reference to it until we get a result
of the above mentioned call. Refactor the code to drop the reference
count at the correct place.
While at it, move to acpi_dev_put() as symmetrical call to the
acpi_dev_get_first_match_dev().
Fixes: 02c0a3b304 ("ASoC: Intel: bytcr_rt5651: add MCLK, quirks and cleanups")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230112112852.67714-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 531390a243 upstream.
This patch is fix for Linux kernel v2.6.33 or later.
For request subaction to IEC 61883-1 FCP region, Linux FireWire subsystem
have had an issue of use-after-free. The subsystem allows multiple
user space listeners to the region, while data of the payload was likely
released before the listeners execute read(2) to access to it for copying
to user space.
The issue was fixed by a commit 281e20323a ("firewire: core: fix
use-after-free regression in FCP handler"). The object of payload is
duplicated in kernel space for each listener. When the listener executes
ioctl(2) with FW_CDEV_IOC_SEND_RESPONSE request, the object is going to
be released.
However, it causes memory leak since the commit relies on call of
release_request() in drivers/firewire/core-cdev.c. Against the
expectation, the function is never called due to the design of
release_client_resource(). The function delegates release task
to caller when called with non-NULL fourth argument. The implementation
of ioctl_send_response() is the case. It should release the object
explicitly.
This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: 281e20323a ("firewire: core: fix use-after-free regression in FCP handler")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20230117090610.93792-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3afee21181 upstream.
This event is just specified for SCO and eSCO link types.
On the reception of a HCI_Synchronous_Connection_Complete for a BDADDR
of an existing LE connection, LE link type and a status that triggers the
second case of the packet processing a NULL pointer dereference happens,
as conn->link is NULL.
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@eng.windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4ccd54d28 upstream.
Many Linux systems are configured to not panic on oops; but allowing an
attacker to oops the system **really** often can make even bugs that look
completely unexploitable exploitable (like NULL dereferences and such) if
each crash elevates a refcount by one or a lock is taken in read mode, and
this causes a counter to eventually overflow.
The most interesting counters for this are 32 bits wide (like open-coded
refcounts that don't use refcount_t). (The ldsem reader count on 32-bit
platforms is just 16 bits, but probably nobody cares about 32-bit platforms
that much nowadays.)
So let's panic the system if the kernel is constantly oopsing.
The speed of oopsing 2^32 times probably depends on several factors, like
how long the stack trace is and which unwinder you're using; an empirically
important one is whether your console is showing a graphical environment or
a text console that oopses will be printed to.
In a quick single-threaded benchmark, it looks like oopsing in a vfork()
child with a very short stack trace only takes ~510 microseconds per run
when a graphical console is active; but switching to a text console that
oopses are printed to slows it down around 87x, to ~45 milliseconds per
run.
(Adding more threads makes this faster, but the actual oops printing
happens under &die_lock on x86, so you can maybe speed this up by a factor
of around 2 and then any further improvement gets eaten up by lock
contention.)
It looks like it would take around 8-12 days to overflow a 32-bit counter
with repeated oopsing on a multi-core X86 system running a graphical
environment; both me (in an X86 VM) and Seth (with a distro kernel on
normal hardware in a standard configuration) got numbers in that ballpark.
12 days aren't *that* short on a desktop system, and you'd likely need much
longer on a typical server system (assuming that people don't run graphical
desktop environments on their servers), and this is a *very* noisy and
violent approach to exploiting the kernel; and it also seems to take orders
of magnitude longer on some machines, probably because stuff like EFI
pstore will slow it down a ton if that's active.
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20221107201317.324457-1-jannh@google.com
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221117234328.594699-2-keescook@chromium.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 751971af2e upstream.
When building ARCH=csky defconfig:
arch/csky/kernel/traps.c: In function 'die':
arch/csky/kernel/traps.c:112:17: error: implicit declaration of function
'make_dead_task' [-Werror=implicit-function-declaration]
112 | make_dead_task(SIGSEGV);
| ^~~~~~~~~~~~~~
The function's name is make_task_dead(), change it so there is no more
build error.
Fixes: 0e25498f8c ("exit: Add and use make_task_dead.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Guo Ren <guoren@kernel.org>
Link: https://lkml.kernel.org/r/20211227184851.2297759-4-nathan@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ab4ababdf7 upstream.
When building ARCH=h8300 defconfig:
arch/h8300/kernel/traps.c: In function 'die':
arch/h8300/kernel/traps.c:109:2: error: implicit declaration of function
'make_dead_task' [-Werror=implicit-function-declaration]
109 | make_dead_task(SIGSEGV);
| ^~~~~~~~~~~~~~
arch/h8300/mm/fault.c: In function 'do_page_fault':
arch/h8300/mm/fault.c:54:2: error: implicit declaration of function
'make_dead_task' [-Werror=implicit-function-declaration]
54 | make_dead_task(SIGKILL);
| ^~~~~~~~~~~~~~
The function's name is make_task_dead(), change it so there is no more
build error.
Additionally, include linux/sched/task.h in arch/h8300/kernel/traps.c
to avoid the same error because do_exit()'s declaration is in kernel.h
but make_task_dead()'s is in task.h, which is not included in traps.c.
Fixes: 0e25498f8c ("exit: Add and use make_task_dead.")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lkml.kernel.org/r/20211227184851.2297759-3-nathan@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1fb466dff9 upstream.
Recently the kbuild robot reported two new errors:
>> lib/kunit/kunit-example-test.o: warning: objtool: .text.unlikely: unexpected end of section
>> arch/x86/kernel/dumpstack.o: warning: objtool: oops_end() falls through to next function show_opcodes()
I don't know why they did not occur in my test setup but after digging
it I realized I had accidentally dropped a comma in
tools/objtool/check.c when I renamed rewind_stack_do_exit to
rewind_stack_and_make_dead.
Add that comma back to fix objtool errors.
Link: https://lkml.kernel.org/r/202112140949.Uq5sFKR1-lkp@intel.com
Fixes: 0e25498f8c ("exit: Add and use make_task_dead.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0e25498f8c upstream.
There are two big uses of do_exit. The first is it's design use to be
the guts of the exit(2) system call. The second use is to terminate
a task after something catastrophic has happened like a NULL pointer
in kernel code.
Add a function make_task_dead that is initialy exactly the same as
do_exit to cover the cases where do_exit is called to handle
catastrophic failure. In time this can probably be reduced to just a
light wrapper around do_task_dead. For now keep it exactly the same so
that there will be no behavioral differences introducing this new
concept.
Replace all of the uses of do_exit that use it for catastraphic
task cleanup with make_task_dead to make it clear what the code
is doing.
As part of this rename rewind_stack_do_exit
rewind_stack_and_make_dead.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3ddd9a808c upstream.
Patch series "sysctl: first set of kernel/sysctl cleanups", v2.
Finally had time to respin the series of the work we had started last
year on cleaning up the kernel/sysct.c kitchen sink. People keeps
stuffing their sysctls in that file and this creates a maintenance
burden. So this effort is aimed at placing sysctls where they actually
belong.
I'm going to split patches up into series as there is quite a bit of
work.
This first set adds register_sysctl_init() for uses of registerting a
sysctl on the init path, adds const where missing to a few places,
generalizes common values so to be more easy to share, and starts the
move of a few kernel/sysctl.c out where they belong.
The majority of rework on v2 in this first patch set is 0-day fixes.
Eric Biederman's feedback is later addressed in subsequent patch sets.
I'll only post the first two patch sets for now. We can address the
rest once the first two patch sets get completely reviewed / Acked.
This patch (of 9):
The kernel/sysctl.c is a kitchen sink where everyone leaves their dirty
dishes, this makes it very difficult to maintain.
To help with this maintenance let's start by moving sysctls to places
where they actually belong. The proc sysctl maintainers do not want to
know what sysctl knobs you wish to add for your own piece of code, we
just care about the core logic.
Today though folks heavily rely on tables on kernel/sysctl.c so they can
easily just extend this table with their needed sysctls. In order to
help users move their sysctls out we need to provide a helper which can
be used during code initialization.
We special-case the initialization use of register_sysctl() since it
*is* safe to fail, given all that sysctls do is provide a dynamic
interface to query or modify at runtime an existing variable. So the
use case of register_sysctl() on init should *not* stop if the sysctls
don't end up getting registered. It would be counter productive to stop
boot if a simple sysctl registration failed.
Provide a helper for init then, and document the recommended init levels
to use for callers of this routine. We will later use this in
subsequent patches to start slimming down kernel/sysctl.c tables and
moving sysctl registration to the code which actually needs these
sysctls.
[mcgrof@kernel.org: major commit log and documentation rephrasing also moved to fs/proc/proc_sysctl.c ]
Link: https://lkml.kernel.org/r/20211123202347.818157-1-mcgrof@kernel.org
Link: https://lkml.kernel.org/r/20211123202347.818157-2-mcgrof@kernel.org
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Paul Turner <pjt@google.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Qing Wang <wangqing@vivo.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jan Kara <jack@suse.cz>
Cc: Amir Goldstein <amir73il@gmail.com>
Cc: Stephen Kitt <steve@sk2.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Julia Lawall <julia.lawall@inria.fr>
Cc: Lukas Middendorf <kernel@tuxforce.de>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: James E.J. Bottomley <jejb@linux.ibm.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1417f59ac0 ]
If the function sdma_load_context() fails, the sdma_desc will be
freed, but the allocated desc->bd is forgot to be freed.
We already met the sdma_load_context() failure case and the log as
below:
[ 450.699064] imx-sdma 30bd0000.dma-controller: Timeout waiting for CH0 ready
...
In this case, the desc->bd will not be freed without this change.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20221130090800.102035-1-hui.wang@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3d81bc1ea ]
The following kernel panic can be triggered when a task with pid=1 attaches
a prog that attempts to send killing signal to itself, also see [1] for more
details:
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
CPU: 3 PID: 1 Comm: systemd Not tainted 6.1.0-09652-g59fe41b5255f #148
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x100/0x178 lib/dump_stack.c:106
panic+0x2c4/0x60f kernel/panic.c:275
do_exit.cold+0x63/0xe4 kernel/exit.c:789
do_group_exit+0xd4/0x2a0 kernel/exit.c:950
get_signal+0x2460/0x2600 kernel/signal.c:2858
arch_do_signal_or_restart+0x78/0x5d0 arch/x86/kernel/signal.c:306
exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
__syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
do_syscall_64+0x44/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd
So skip task with pid=1 in bpf_send_signal_common() to avoid the panic.
[1] https://lore.kernel.org/bpf/20221222043507.33037-1-sunhao.th@gmail.com
Signed-off-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20230106084838.12690-1-sunhao.th@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f78985f9f5 ]
"make dtbs_check":
arch/arm/boot/dts/imx53-ppd.dtb: i2c-switch@70: $nodename:0: 'i2c-switch@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm/boot/dts/imx53-ppd.dtb: i2c-switch@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3', 'i2c@4', 'i2c@5', 'i2c@6', 'i2c@7' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
Fix this by renaming the PCA9547 node to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a44b765148 upstream.
An SCTP endpoint can start an association through a path and tear it
down over another one. That means the initial path will not see the
shutdown sequence, and the conntrack entry will remain in ESTABLISHED
state for 5 days.
By merging the HEARTBEAT_ACKED and ESTABLISHED states into one
ESTABLISHED state, there remains no difference between a primary or
secondary path. The timeout for the merged ESTABLISHED state is set to
210 seconds (hb_interval * max_path_retrans + rto_max). So, even if a
path doesn't see the shutdown sequence, it will expire in a reasonable
amount of time.
With this change in place, there is now more than one state from which
we can transition to ESTABLISHED, COOKIE_ECHOED and HEARTBEAT_SENT, so
handle the setting of ASSURED bit whenever a state change has happened
and the new state is ESTABLISHED. Removed the check for dir==REPLY since
the transition to ESTABLISHED can happen only in the reply direction.
Fixes: 9fb9cbb108 ("[NETFILTER]: Add nf_conntrack subsystem.")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fa5595072 upstream.
Baoquan reported that after triggering a crash the subsequent crash-kernel
fails to boot about half of the time. It triggers a NULL pointer
dereference in the periodic tick code.
This happens because the legacy timer interrupt (IRQ0) is resent in
software which happens in soft interrupt (tasklet) context. In this context
get_irq_regs() returns NULL which leads to the NULL pointer dereference.
The reason for the resend is a spurious APIC interrupt on the IRQ0 vector
which is captured and leads to a resend when the legacy timer interrupt is
enabled. This is wrong because the legacy PIC interrupts are level
triggered and therefore should never be resent in software, but nothing
ever sets the IRQ_LEVEL flag on those interrupts, so the core code does not
know about their trigger type.
Ensure that IRQ_LEVEL is set when the legacy PCI interrupts are set up.
Fixes: a4633adcdb ("[PATCH] genirq: add genirq sw IRQ-retrigger")
Reported-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Baoquan He <bhe@redhat.com>
Link: https://lore.kernel.org/r/87mt6rjrra.ffs@tglx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6c7f2a84d upstream.
In order to ensure that knfsd threads don't linger once the nfsd
pseudofs is unmounted (e.g. when the container is killed) we let
nfsd_umount() shut down those threads and wait for them to exit.
This also should ensure that we don't need to do a kernel mount of
the pseudofs, since the thread lifetime is now limited by the
lifetime of the filesystem.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
