[ Upstream commit a868e85304 ]
After removing an entry from a queue (e.g. reading an event in
arm_smmu_evtq_thread()) it is necessary to advance the MMIO consumer
pointer to free the queue slot back to the SMMU. A memory barrier is
required here so that all reads targetting the queue entry have
completed before the consumer pointer is updated.
The implementation of queue_inc_cons() relies on a writel() to complete
the previous reads, but this is incorrect because writel() is only
guaranteed to complete prior writes. This patch replaces the call to
writel() with an mb(); writel_relaxed() sequence, which gives us the
read->write ordering which we require.
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17f6c83fb5 ]
For micro-mips, srlv inside POOL32A encoding space should use 0x50
sub-opcode, NOT 0x90.
Some early version ISA doc describes the encoding as 0x90 for both srlv and
srav, this looks to me was a typo. I checked Binutils libopcode
implementation which is using 0x50 for srlv and 0x90 for srav.
v1->v2:
- Keep mm_srlv32_op sorted by value.
Fixes: f31318fdf3 ("MIPS: uasm: Add srlv uasm instruction")
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84fb6c7feb ]
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12b08ebbe ]
The parameter is still there but it's ignored. We need to check its
value before deciding to go into passthrough mode for AMD IOMMU v2
capable device.
We occasionally use this parameter to force v2 capable device into
translation mode to debug memory corruption that we suspect is
caused by DMA writes.
To address the following comment from Joerg Roedel on the first
version, v2 capability of device is completely ignored.
> This breaks the iommu_v2 use-case, as it needs a direct mapping for the
> devices that support it.
And from Documentation/admin-guide/kernel-parameters.txt:
This option does not override iommu=pt
Fixes: aafd8ba0ca ("iommu/amd: Implement add_device and remove_device")
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e6da2039c ]
All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.
Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e86108940e ]
When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.
USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.
Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b841bfab6 ]
Function smack_key_permission() only issues smack requests for the
following operations:
- KEY_NEED_READ (issues MAY_READ)
- KEY_NEED_WRITE (issues MAY_WRITE)
- KEY_NEED_LINK (issues MAY_WRITE)
- KEY_NEED_SETATTR (issues MAY_WRITE)
A blank smack request is issued in all other cases, resulting in
smack access being granted if there is any rule defined between
subject and object, or denied with -EACCES otherwise.
Request MAY_READ access for KEY_NEED_SEARCH and KEY_NEED_VIEW.
Fix the logic in the unlikely case when both MAY_READ and
MAY_WRITE are needed. Validate access permission field for valid
contents.
Signed-off-by: Zoran Markovic <zmarkovic@sierrawireless.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa35dc3c71 ]
If vpbe_set_default_output() or vpbe_set_default_mode() fails,
vpbe_initialize() returns error code without releasing resources.
The patch adds error handling for that case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1147e05ac9 ]
Marvell keeps their MMP2 datasheet secret, but there are good clues
that TWSI2 is not on 0xd4025000 on that platform, not does it use
IRQ 58. In fact, the IRQ 58 on MMP2 seems to be a signal processor:
arch/arm/mach-mmp/irqs.h:#define IRQ_MMP2_MSP 58
I'm taking a somewhat educated guess that is probably a copy & paste
error from PXA168 or PXA910 and that the real controller in fact hides
at address 0xd4031000 and uses an interrupt line multiplexed via IRQ 17.
I'm also copying some properties from TWSI1 that were missing or
incorrect.
Tested on a OLPC XO 1.75 machine, where the RTC is on TWSI2.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e803e2e6e ]
The core ftrace code requires that when it is handed the PC of an
instrumented function, this PC is the address of the instrumented
instruction. This is necessary so that the core ftrace code can identify
the specific instrumentation site. Since the instrumented function will
be a BL, the address of the instrumented function is LR - 4 at entry to
the ftrace code.
This fixup is applied in the mcount_get_pc and mcount_get_pc0 helpers,
which acquire the PC of the instrumented function.
The mcount_get_lr helper is used to acquire the LR of the instrumented
function, whose value does not require this adjustment, and cannot be
adjusted to anything meaningful. No adjustment of this value is made on
other architectures, including arm. However, arm64 adjusts this value by
4.
This patch brings arm64 in line with other architectures and removes the
adjustment of the LR value.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Torsten Duwe <duwe@suse.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab2180a15c ]
Since commit:
ce2e6db554 ("brcmfmac: Add support for getting nvram contents from EFI variables")
we have a device driver accessing the efivars API. Several functions in
the efivars API assume __efivars is set, i.e., that they will be accessed
only after efivars_register() has been called. However, the following NULL
pointer access was reported calling efivar_entry_size() from the brcmfmac
device driver:
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = 60bfa5f1
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
...
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
Workqueue: events request_firmware_work_func
PC is at efivar_entry_size+0x28/0x90
LR is at brcmf_fw_complete_request+0x3f8/0x8d4 [brcmfmac]
pc : [<c0c40718>] lr : [<bf2a3ef4>] psr: a00d0113
sp : ede7fe28 ip : ee983410 fp : c1787f30
r10: 00000000 r9 : 00000000 r8 : bf2b2258
r7 : ee983000 r6 : c1604c48 r5 : ede7fe88 r4 : edf337c0
r3 : 00000000 r2 : 00000000 r1 : ede7fe88 r0 : c17712c8
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: ad16804a DAC: 00000051
Disassembly showed that the local static variable __efivars is NULL,
which is not entirely unexpected given that it is a non-EFI platform.
So add a NULL pointer check to efivar_entry_size(), and to related
functions while at it. In efivars_register() a couple of sanity checks
are added as well.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bhupesh Sharma <bhsharma@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Eric Snowberg <eric.snowberg@oracle.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Julien Thierry <julien.thierry@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: YiFei Zhu <zhuyifei1999@gmail.com>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20181129171230.18699-9-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 964f4843a4 ]
commit ff140fea84 ("Thermal: handle thermal zone device properly
during system sleep") added PM hook to call thermal zone reset during
sleep. However resetting thermal zone will also clear the passive state
and thus cancel the polling queue which leads the passive cooling device
state not being cleared properly after sleep.
thermal_pm_notify => thermal_zone_device_reset set passive to 0
thermal_zone_trip_update will skip update passive as `old_target ==
instance->target'.
monitor_thermal_zone => thermal_zone_device_set_polling will cancel
tz->poll_queue, so the cooling device state will not be changed
afterwards.
Reported-by: Kame Wang <kamewang@google.com>
Signed-off-by: Wei Wang <wvw@google.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62a063b8e7 ]
Anatoly Trosinenko reports that this:
1) Checkout fresh master Linux branch (tested with commit e195ca6cb)
2) Copy x84_64-config-4.14 to .config, then enable NFS server v4 and build
3) From `kvm-xfstests shell`:
results in NULL dereference in locks_end_grace.
Check that nfsd has been started before trying to end the grace period.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1861a7f07e ]
of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_brcmstb()
doesn't do that, so fix it.
[treding: slightly rewrite to avoid inline comparison]
Fixes: d52fad2620 ("soc: add stubs for brcmstb SoC's")
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11f6ca9ae ]
__vdc_tx_trigger should only loop on EAGAIN a finite
number of times.
See commit adddc32d6f ("sunvnet: Do not spin in an
infinite loop when vio_ldc_send() returns EAGAIN") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2912289a51 ]
The v4l2_dv_timings_cap struct is used to do sanity checks when setting and
enumerating DV timings, ensuring that only valid timings as per the HW
capabilities are allowed.
However, many drivers just filled in 0 for the minimum width, height or
pixelclock frequency. This can cause timings with e.g. 0 as width and height
to be accepted, which will in turn lead to a potential division by zero.
Fill in proper values are minimum boundaries. 640x350 was chosen since it is
the smallest resolution in v4l2-dv-timings.h. Same for 13 MHz as the lowest
pixelclock frequency (it's slightly below the minimum of 13.5 MHz in the
v4l2-dv-timings.h header).
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f6232e695 ]
Various 2-in-1's use KIOX010A and KIOX020A as HIDs for 2 KXCJ91008
accelerometers. The KIOX010A HID is for the one in the base and the
KIOX020A for the accelerometer in the keyboard.
Since userspace does not have a way yet to deal with (or ignore) the
accelerometer in the keyboard, this commit just adds the KIOX010A HID
for now so that display rotation will work.
Related: https://github.com/hadess/iio-sensor-proxy/issues/166
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aeaebcc17c ]
Clang warns:
drivers/dma/xilinx/zynqmp_dma.c:166:4: warning: attribute 'aligned' is
ignored, place it after "struct" to apply attribute to type declaration
[-Wignored-attributes]
}; __aligned(64)
^
./include/linux/compiler_types.h:200:38: note: expanded from macro
'__aligned'
^
1 warning generated.
As Nick pointed out in the previous version of this patch, the author
likely intended for this struct to be 8-byte (64-bit) aligned, not
64-byte, which is the default. Remove the hanging __aligned attribute.
Fixes: b0cc417c16 ("dmaengine: Add Xilinx zynqmp dma engine driver support")
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ea0f2ba0f ]
of_parse_phandle() returns the device node with refcount incremented.
There are two nodes that are used temporary in mtk_vcodec_init_enc_pm(),
but their refcounts are not decremented.
The patch adds one of_node_put() and fixes returning error codes.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9eb40fa2cd ]
of_find_node_by_path() acquires a reference to the node returned by it
and that reference needs to be dropped by its caller. soc_is_tegra()
doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
[treding: slightly rewrite to avoid inline comparison]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5818c683a6 ]
If an ARM mapping symbol shares an address with a valid symbol,
find_elf_symbol can currently return the mapping symbol instead, as the
symbol is not validated. This can result in confusing warnings:
WARNING: vmlinux.o(.text+0x18f4028): Section mismatch in reference
from the function set_reset_devices() to the variable .init.text:$x.0
This change adds a call to is_valid_name to find_elf_symbol, similarly
to how it's already used in find_elf_symbol2.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c10b26abeb ]
When building the kernel with Clang, the following section mismatch
warnings appears:
WARNING: vmlinux.o(.text+0x2d398): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_iclk_autoidle()
The function _setup() references
the function __init _setup_iclk_autoidle().
This is often because _setup lacks a __init
annotation or the annotation of _setup_iclk_autoidle is wrong.
WARNING: vmlinux.o(.text+0x2d3a0): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_reset()
The function _setup() references
the function __init _setup_reset().
This is often because _setup lacks a __init
annotation or the annotation of _setup_reset is wrong.
WARNING: vmlinux.o(.text+0x2d408): Section mismatch in reference from
the function _setup() to the function .init.text:_setup_postsetup()
The function _setup() references
the function __init _setup_postsetup().
This is often because _setup lacks a __init
annotation or the annotation of _setup_postsetup is wrong.
_setup is used in omap_hwmod_allocate_module, which isn't marked __init
and looks like it shouldn't be, meaning to fix these warnings, those
functions must be moved out of the init section, which this patch does.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 336650c785 ]
The ad7780 driver previously did not read the correct device output, as
it read an outdated value set at initialization. It now updates its
voltage on read.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3a3eafeef ]
Previously, ad2s90_probe ignored the return code from spi_setup, not
handling its possible failure. This patch makes ad2s90_probe check if
the code is an error code and, if so, do the following:
- Call dev_err with an appropriate error message.
- Return the spi_setup's error code.
Note: The 'return ret' statement could be out of the 'if' block, but
this whole block will be moved up in the function in the patch:
'staging:iio:ad2s90: Move device registration to the end of probe'.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0560054da5 ]
For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b3f5c408d ]
The previous commit, "of: overlay: add missing of_node_get() in
__of_attach_node_sysfs" added a missing of_node_get() to
__of_attach_node_sysfs(). This results in a refcount imbalance
for nodes attached with dlpar_attach_node(). The calling sequence
from dlpar_attach_node() to __of_attach_node_sysfs() is:
dlpar_attach_node()
of_attach_node()
__of_attach_node_sysfs()
For more detailed description of the node refcount, see
commit 68baf692c4 ("powerpc/pseries: Fix of_node_put() underflow
during DLPAR remove").
Tested-by: Alan Tull <atull@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53bb565fc5 ]
In the expression "word1 << 16", word1 starts as u16, but is promoted to a
signed int, then sign-extended to resource_size_t, which is probably not
what was intended. Cast to resource_size_t to avoid the sign extension.
This fixes an identical issue as fixed by commit 0b2d70764b ("x86/PCI:
Fix Broadcom CNB20LE unintended sign extension") back in 2014.
Detected by CoverityScan, CID#138749, 138750 ("Unintended sign extension")
Fixes: 3f6ea84a30 ("PCI: read memory ranges out of Broadcom CNB20LE host bridge")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 216f0efd19 ]
Before this patch, recovery would cause all callbacks to be delayed,
put on a queue, and afterward they were all queued to the callback
work queue. This patch does the same thing, but occasionally takes
a break after 25 of them so it won't swamp the CPU at the expense
of other RT processes like corosync.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82c08c3e7f ]
In case panic() and panic() called at the same time on different CPUS.
For example:
CPU 0:
panic()
__crash_kexec
machine_crash_shutdown
crash_smp_send_stop
machine_kexec
BUG_ON(num_online_cpus() > 1);
CPU 1:
panic()
local_irq_disable
panic_smp_self_stop
If CPU 1 calls panic_smp_self_stop() before crash_smp_send_stop(), kdump
fails. CPU1 can't receive the ipi irq, CPU1 will be always online.
To fix this problem, this patch split out the panic_smp_self_stop()
and add set_cpu_online(smp_processor_id(), false).
Signed-off-by: Yufen Wang <wangyufen@huawei.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b114d9009d ]
When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3831a2a001 ]
In order to properly support dynack in ad-hoc mode running
wpa_supplicant, take into account authentication frames for
'late ack' detection. This patch has been tested on devices
mounted on offshore high-voltage stations connected through
~24Km link
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 819bec35c8 ]
Prevent possible race by parallel threads between ipu_image_convert_run()
and ipu_image_convert_unprepare(). This involves setting ctx->aborting
to true unconditionally so that no new job runs can be queued during
unprepare, and holding the ctx->aborting flag until the context is freed.
Note that the "normal" ipu_image_convert_abort() case (e.g. not during
context unprepare) should clear the ctx->aborting flag after aborting
any active run and clearing the context's pending queue. This is because
it should be possible to continue to use the conversion context and queue
more runs after an abort.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1539c7f23f ]
Randconfig testing revealed a very old bug, with gcc-8:
sound/soc/intel/atom/sst/sst_loader.c: In function 'sst_load_fw':
sound/soc/intel/atom/sst/sst_loader.c:357:5: error: 'fw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (fw == NULL) {
^
sound/soc/intel/atom/sst/sst_loader.c:354:25: note: 'fw' was declared here
const struct firmware *fw;
We must check the return code of request_firmware() before we look at the
pointer result that may be uninitialized when the function fails.
Fixes: 9012c9544e ("ASoC: Intel: mrfld - Add DSP load and management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0559ef7fde ]
Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative
error code. This change will ensure that this error is being passed up
in the call stack, so it can be handled.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a378050989 ]
idx can be indirectly controlled by user-space, hence leading to a
potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/gpu/drm/drm_bufs.c:1420 drm_legacy_freebufs() warn: potential
spectre issue 'dma->buflist' [r] (local cap)
Fix this by sanitizing idx before using it to index dma->buflist
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016095549.GA23586@embeddedor.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b469e7e47c upstream.
When an event is reported on a sub-directory and the parent inode has
a mark mask with FS_EVENT_ON_CHILD|FS_ISDIR, the event will be sent to
fsnotify() even if the event type is not in the parent mark mask
(e.g. FS_OPEN).
Further more, if that event happened on a mount or a filesystem with
a mount/sb mark that does have that event type in their mask, the "on
child" event will be reported on the mount/sb mark. That is not
desired, because user will get a duplicate event for the same action.
Note that the event reported on the victim inode is never merged with
the event reported on the parent inode, because of the check in
should_merge(): old_fsn->inode == new_fsn->inode.
Fix this by looking for a match of an actual event type (i.e. not just
FS_ISDIR) in parent's inode mark mask and by not reporting an "on child"
event to group if event type is only found on mount/sb marks.
[backport hint: The bug seems to have always been in fanotify, but this
patch will only apply cleanly to v4.19.y]
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
[amir: backport to v4.9]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79f546a696 upstream.
We recently had an oops reported on a 4.14 kernel in
xfs_reclaim_inodes_count() where sb->s_fs_info pointed to garbage
and so the m_perag_tree lookup walked into lala land. It produces
an oops down this path during the failed mount:
radix_tree_gang_lookup_tag+0xc4/0x130
xfs_perag_get_tag+0x37/0xf0
xfs_reclaim_inodes_count+0x32/0x40
xfs_fs_nr_cached_objects+0x11/0x20
super_cache_count+0x35/0xc0
shrink_slab.part.66+0xb1/0x370
shrink_node+0x7e/0x1a0
try_to_free_pages+0x199/0x470
__alloc_pages_slowpath+0x3a1/0xd20
__alloc_pages_nodemask+0x1c3/0x200
cache_grow_begin+0x20b/0x2e0
fallback_alloc+0x160/0x200
kmem_cache_alloc+0x111/0x4e0
The problem is that the superblock shrinker is running before the
filesystem structures it depends on have been fully set up. i.e.
the shrinker is registered in sget(), before ->fill_super() has been
called, and the shrinker can call into the filesystem before
fill_super() does it's setup work. Essentially we are exposed to
both use-after-free and use-before-initialisation bugs here.
To fix this, add a check for the SB_BORN flag in super_cache_count.
In general, this flag is not set until ->fs_mount() completes
successfully, so we know that it is set after the filesystem
setup has completed. This matches the trylock_super() behaviour
which will not let super_cache_scan() run if SB_BORN is not set, and
hence will not allow the superblock shrinker from entering the
filesystem while it is being set up or after it has failed setup
and is being torn down.
Cc: stable@kernel.org
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Aaron Lu <aaron.lu@linux.alibaba.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 726e410979 upstream.
For devices with a class, we create a "glue" directory between
the parent device and the new device with the class name.
This directory is never "explicitely" removed when empty however,
this is left to the implicit sysfs removal done by kobject_release()
when the object loses its last reference via kobject_put().
This is problematic because as long as it's not been removed from
sysfs, it is still present in the class kset and in sysfs directory
structure.
The presence in the class kset exposes a use after free bug fixed
by the previous patch, but the presence in sysfs means that until
the kobject is released, which can take a while (especially with
kobject debugging), any attempt at re-creating such as binding a
new device for that class/parent pair, will result in a sysfs
duplicate file name error.
This fixes it by instead doing an explicit kobject_del() when
the glue dir is empty, by keeping track of the number of
child devices of the gluedir.
This is made easy by the fact that all glue dir operations are
done with a global mutex, and there's already a function
(cleanup_glue_dir) called in all the right places taking that
mutex that can be enhanced for this. It appears that this was
in fact the intent of the function, but the implementation was
wrong.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Cc: Guenter Roeck <groeck@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0a352fabc upstream.
We had a race in the old balloon compaction code before b1123ea6d3
("mm: balloon: use general non-lru movable page feature") refactored it
that became visible after backporting 195a8c43e9 ("virtio-balloon:
deflate via a page list") without the refactoring.
The bug existed from commit d6d86c0a7f ("mm/balloon_compaction:
redesign ballooned pages management") till b1123ea6d3 ("mm: balloon:
use general non-lru movable page feature"). d6d86c0a7f
("mm/balloon_compaction: redesign ballooned pages management") was
backported to 3.12, so the broken kernels are stable kernels [3.12 -
4.7].
There was a subtle race between dropping the page lock of the newpage in
__unmap_and_move() and checking for __is_movable_balloon_page(newpage).
Just after dropping this page lock, virtio-balloon could go ahead and
deflate the newpage, effectively dequeueing it and clearing PageBalloon,
in turn making __is_movable_balloon_page(newpage) fail.
This resulted in dropping the reference of the newpage via
putback_lru_page(newpage) instead of put_page(newpage), leading to
page->lru getting modified and a !LRU page ending up in the LRU lists.
With 195a8c43e9 ("virtio-balloon: deflate via a page list")
backported, one would suddenly get corrupted lists in
release_pages_balloon():
- WARNING: CPU: 13 PID: 6586 at lib/list_debug.c:59 __list_del_entry+0xa1/0xd0
- list_del corruption. prev->next should be ffffe253961090a0, but was dead000000000100
Nowadays this race is no longer possible, but it is hidden behind very
ugly handling of __ClearPageMovable() and __PageMovable().
__ClearPageMovable() will not make __PageMovable() fail, only
PageMovable(). So the new check (__PageMovable(newpage)) will still
hold even after newpage was dequeued by virtio-balloon.
If anybody would ever change that special handling, the BUG would be
introduced again. So instead, make it explicit and use the information
of the original isolated page before migration.
This patch can be backported fairly easy to stable kernels (in contrast
to the refactoring).
Link: http://lkml.kernel.org/r/20190129233217.10747-1-david@redhat.com
Fixes: d6d86c0a7f ("mm/balloon_compaction: redesign ballooned pages management")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Vratislav Bendel <vbendel@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Vratislav Bendel <vbendel@redhat.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [3.12 - 4.7]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6376360ecb upstream.
Currently memory_failure() is racy against process's exiting, which
results in kernel crash by null pointer dereference.
The root cause is that memory_failure() uses force_sig() to forcibly
kill asynchronous (meaning not in the current context) processes. As
discussed in thread https://lkml.org/lkml/2010/6/8/236 years ago for OOM
fixes, this is not a right thing to do. OOM solves this issue by using
do_send_sig_info() as done in commit d2d393099d ("signal:
oom_kill_task: use SEND_SIG_FORCED instead of force_sig()"), so this
patch is suggesting to do the same for hwpoison. do_send_sig_info()
properly accesses to siglock with lock_task_sighand(), so is free from
the reported race.
I confirmed that the reported bug reproduces with inserting some delay
in kill_procs(), and it never reproduces with this patch.
Note that memory_failure() can send another type of signal using
force_sig_mceerr(), and the reported race shouldn't happen on it because
force_sig_mceerr() is called only for synchronous processes (i.e.
BUS_MCEERR_AR happens only when some process accesses to the corrupted
memory.)
Link: http://lkml.kernel.org/r/20190116093046.GA29835@hori1.linux.bs1.fc.nec.co.jp
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefc7ef3c8 upstream.
Syzbot instance running on upstream kernel found a use-after-free bug in
oom_kill_process. On further inspection it seems like the process
selected to be oom-killed has exited even before reaching
read_lock(&tasklist_lock) in oom_kill_process(). More specifically the
tsk->usage is 1 which is due to get_task_struct() in oom_evaluate_task()
and the put_task_struct within for_each_thread() frees the tsk and
for_each_thread() tries to access the tsk. The easiest fix is to do
get/put across the for_each_thread() on the selected task.
Now the next question is should we continue with the oom-kill as the
previously selected task has exited? However before adding more
complexity and heuristics, let's answer why we even look at the children
of oom-kill selected task? The select_bad_process() has already selected
the worst process in the system/memcg. Due to race, the selected
process might not be the worst at the kill time but does that matter?
The userspace can use the oom_score_adj interface to prefer children to
be killed before the parent. I looked at the history but it seems like
this is there before git history.
Link: http://lkml.kernel.org/r/20190121215850.221745-1-shakeelb@google.com
Reported-by: syzbot+7fbbfa368521945f0e3d@syzkaller.appspotmail.com
Fixes: 6b0c81b3be ("mm, oom: reduce dependency on tasklist_lock")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fb335e078 upstream.
Currently, exit_ptrace() adds all ptraced tasks in a dead list, then
zap_pid_ns_processes() waits on all tasks in a current pidns, and only
then are tasks from the dead list released.
zap_pid_ns_processes() can get stuck on waiting tasks from the dead
list. In this case, we will have one unkillable process with one or
more dead children.
Thanks to Oleg for the advice to release tasks in find_child_reaper().
Link: http://lkml.kernel.org/r/20190110175200.12442-1-avagin@gmail.com
Fixes: 7c8bd2322c ("exit: ptrace: shift "reap dead" code from exit_ptrace() to forget_original_parent()")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
