commit 68aa95d5d4 upstream.
This patch (as1489) works around a hardware bug in MosChip EHCI
controllers. Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter). If the register is read at just the wrong time, the value
obtained is too low by 8.
When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0. This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jason N Pitt <jpitt@fhcrc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 276532ba96 upstream.
The Kirkwood gave an unaligned memory access error on
line 742 of drivers/usb/host/echi-hcd.c:
"ehci->last_periodic_enable = ktime_get_real();"
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 94abc56f4d upstream.
The following patch removed uart_change_pm() in uart_resume_port():
commit 5933a161ab
Author: Yin Kangkai <kangkai.yin@linux.intel.com>
serial-core: reset the console speed on resume
It will break the pxa serial driver when the system resumes from suspend mode
as it will try to set baud rate divider register in set_termios but with
clock off. The register value can not be set correctly on some platform if
the clock is disabled. The pxa driver will check the value and report the
following warning:
------------[ cut here ]------------
WARNING: at drivers/tty/serial/pxa.c:545 serial_pxa_set_termios+0x1dc/0x250()
Modules linked in:
[<c0281f30>] (unwind_backtrace+0x0/0xf0) from [<c029341c>] (warn_slowpath_common+0x4c/0x64)
[<c029341c>] (warn_slowpath_common+0x4c/0x64) from [<c029344c>] (warn_slowpath_null+0x18/0x1c)
[<c029344c>] (warn_slowpath_null+0x18/0x1c) from [<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250)
[<c044b1e4>] (serial_pxa_set_termios+0x1dc/0x250) from [<c044a840>] (uart_resume_port+0x128/0x2dc)
[<c044a840>] (uart_resume_port+0x128/0x2dc) from [<c044bbe0>] (serial_pxa_resume+0x18/0x24)
[<c044bbe0>] (serial_pxa_resume+0x18/0x24) from [<c0454d34>] (platform_pm_resume+0x40/0x4c)
[<c0454d34>] (platform_pm_resume+0x40/0x4c) from [<c0457ebc>] (pm_op+0x68/0xb4)
[<c0457ebc>] (pm_op+0x68/0xb4) from [<c0458368>] (device_resume+0xb0/0xec)
[<c0458368>] (device_resume+0xb0/0xec) from [<c04584c8>] (dpm_resume+0xe0/0x194)
[<c04584c8>] (dpm_resume+0xe0/0x194) from [<c0458588>] (dpm_resume_end+0xc/0x18)
[<c0458588>] (dpm_resume_end+0xc/0x18) from [<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac)
[<c02c518c>] (suspend_devices_and_enter+0x16c/0x1ac) from [<c02c5278>] (enter_state+0xac/0xdc)
[<c02c5278>] (enter_state+0xac/0xdc) from [<c02c48ec>] (state_store+0xa0/0xbc)
[<c02c48ec>] (state_store+0xa0/0xbc) from [<c0408f7c>] (kobj_attr_store+0x18/0x1c)
[<c0408f7c>] (kobj_attr_store+0x18/0x1c) from [<c034a6a4>] (sysfs_write_file+0x108/0x140)
[<c034a6a4>] (sysfs_write_file+0x108/0x140) from [<c02fb798>] (vfs_write+0xac/0x134)
[<c02fb798>] (vfs_write+0xac/0x134) from [<c02fb8cc>] (sys_write+0x3c/0x68)
[<c02fb8cc>] (sys_write+0x3c/0x68) from [<c027c700>] (ret_fast_syscall+0x0/0x2c)
---[ end trace 88289eceb4675b04 ]---
This patch fix the problem by adding the power on opertion back for uart
console when console_suspend_enabled is true.
Signed-off-by: Ning Jiang <ning.jiang@marvell.com>
Tested-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e44aabd649 upstream.
Errata E20: UART: Character Timeout interrupt remains set under certain
software conditions.
Implication: The software servicing the UART can be trapped in an infinite loop.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 68c79e5756 upstream.
Simple patch to make qcserial recognize the USB id of the Sierra
Wireless MC8355 which is based on the Gobi 3000 chip.
Both UMTS and GPS work fine.
Signed-off-by: Richard Hartmann <richih.mailinglist@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c4b6a2eaf1 upstream.
netif_notify_peers() caused a kernel warning in netvsc_linkstatus_callback(),
because netvsc_linkstatus_callback() is within IRQ context. So we move
the first call to netif_notify_peers() into queued work as well, but with
zero delay.
In addition to "staging-next", this should also be back-ported to stable
kernels 2.6.32 and later.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit e8df1674d3 upstream.
If the usermode app does an ioctl over this serial device by
using TIOCMIWAIT, then the code will wait by setting the current
task state to TASK_INTERRUPTIBLE and then calling schedule().
This will be woken up by the qt2_process_modem_status on URB
completion when the port_extra->shadowMSR is set to the new
modem status.
However, this could result in a lost wakeup scenario due to a race
in the logic in the qt2_ioctl(TIOCMIWAIT) loop and the URB completion
for new modem status in qt2_process_modem_status.
Due to this, the usermode app's task will continue to sleep despite a
change in the modem status.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7cbf3c7cd5 upstream.
The serqt_usb2 driver will not work properly with the ssu100 device
even though it claims to support it. The ssu100 is supported by the
ssu100 driver in mainline so there is no need to have it claimed by
serqt_usb2.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 7518b9b8fc upstream.
Revert changes in definitions that were submitted on May 11 2011 and
committed on June 7 2011. No reason for the change in these values was
given in the patch comment, it broke compatibility with older
versions, and was difficult to detect by the simultaneous move of the
lines of code.
Signed-off-by: Alexander Thomas <alexander.thomas@esaturnus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c5a48592d8 upstream.
A return value of -EINPROGRESS from pm_runtime_get indicates that
the device is already resuming due to a previous call. Internally,
usb_autopm_get_interface_async doesn't treat this as an error and
increments the usage count, but passes the error status along
to the caller. The logical assumption of the caller is that
any negative return value reflects the device not resuming
and the pm_usage_cnt not being incremented. Since the usage count
is being incremented and the device is resuming, return success (0)
instead.
Signed-off-by: James Wylder <james.wylder@motorola.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 1177c0efc0 upstream.
Mistakenly, commit 64ba3dc314 (tty: never hold BTM while getting
tty_mutex) switched one fail path in ptmx_open to not free the newly
allocated tty.
Fix that by jumping to the appropriate place. And rename the labels so
that it's clear what is going on there.
Introduced-in: v2.6.36-rc2
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit fa90e1c935 upstream.
If tty_add_file fails at the point it is now, we have to revert all
the changes we did to the tty. It means either decrease all refcounts
if this was a tty reopen or delete the tty if it was newly allocated.
There was a try to fix this in v3.0-rc2 using tty_release in 0259894c7
(TTY: fix fail path in tty_open). But instead it introduced a NULL
dereference. It's because tty_release dereferences
filp->private_data, but that one is set even in our tty_add_file. And
when tty_add_file fails, it's still NULL/garbage. Hence tty_release
cannot be called there.
To circumvent the original leak (and the current NULL deref) we split
tty_add_file into two functions, making the latter non-failing. In
that case we may do the former early in open, where handling failures
is easy. The latter stays as it is now. So there is no change in
functionality.
The original bug (leak) was introduced by f573bd176 (tty: Remove
__GFP_NOFAIL from tty_add_file()). Thanks Dan for reporting this.
Later, we may split tty_release into more functions and call only some
of them in this fail path instead. (If at all possible.)
Introduced-in: v2.6.37-rc2
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit c290f8358a upstream.
When tty_driver_lookup_tty fails in tty_open, we forget to drop a
reference to the tty driver. This was added by commit 4a2b5fddd5 (Move
tty lookup/reopen to caller).
Fix that by adding tty_driver_kref_put to the fail path.
I will refactor the code later. This is for the ease of backporting to
stable.
Introduced-in: v2.6.28-rc2
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/iommu-2.6:
intel-iommu: fix superpage support in pfn_to_dma_pte()
intel-iommu: set iommu_superpage on VM domains to lowest common denominator
intel-iommu: fix return value of iommu_unmap() API
MAINTAINERS: Update VT-d entry for drivers/pci -> drivers/iommu move
intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.
intel-iommu: Workaround IOTLB hang on Ironlake GPU
intel-iommu: Fix AB-BA lockdep report
Commit 4b239f458 ("x86-64, mm: Put early page table high") causes a S4
regression since 2.6.39, namely the machine reboots occasionally at S4
resume. It doesn't happen always, overall rate is about 1/20. But,
like other bugs, once when this happens, it continues to happen.
This patch fixes the problem by essentially reverting the memory
assignment in the older way.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yinghai.lu@oracle.com>
[ We'll hopefully find the real fix, but that's too late for 3.1 now ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix memory leak introduced by commit a6e50b409d
(dm snapshot: skip reading origin when overwriting complete chunk).
When allocating a set of jobs from kc->job_pool, job->master_job must be
set (to point to itself) so that the mempool item gets freed when the
master_job completes.
master_job was introduced by commit c6ea41fbbe
(dm kcopyd: preallocate sub jobs to avoid deadlock)
Reported-by: Michael Leun <ml@newton.leun.net>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
v2:
- register_syscore_ops(&s3c24xx_irq_syscore_ops) does not need to be
conditionally compiled out, it is already optimized out on !CONFIG_PM
- fix also s3c2412 and s3c2416 affected by the same build issue
v1:
s3c2440.c fails to build if !CONFIG_PM because in such case
s3c2410_pm_syscore_ops is not defined. Same error should happen also
in s3c2410.c and s3c2442.c
Signed-off-by: Domenico Andreoli <cavokz@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Offsets of the irq controller registers were calculated
correctly only for first GPIO bank. This patch fixes
calculation of the register offsets for all GPIO banks.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
fib_rules: fix unresolved_rules counting
r8169: fix wrong eee setting for rlt8111evl
r8169: fix driver shutdown WoL regression.
ehea: Change maintainer to me
pptp: pptp_rcv_core() misses pskb_may_pull() call
tproxy: copy transparent flag when creating a time wait
pptp: fix skb leak in pptp_xmit()
bonding: use local function pointer of bond->recv_probe in bond_handle_frame
smsc911x: Add support for SMSC LAN89218
tg3: negate USE_PHYLIB flag check
netconsole: enable netconsole can make net_device refcnt incorrent
bluetooth: Properly clone LSM attributes to newly created child connections
l2tp: fix a potential skb leak in l2tp_xmit_skb()
bridge: fix hang on removal of bridge via netlink
x25: Prevent skb overreads when checking call user data
x25: Handle undersized/fragmented skbs
x25: Validate incoming call user data lengths
udplite: fast-path computation of checksum coverage
IPVS netns shutdown/startup dead-lock
netfilter: nf_conntrack: fix event flooding in GRE protocol tracker
Since 8-bit temperature values are now handled in 16-bit struct
members, values have to be cast to s8 for negative temperatures to be
properly handled. This is broken since kernel version 2.6.39
(commit bce26c58df86599c9570cee83eac58bdaae760e4.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
I don't usually pay much attention to the stale "? " addresses in
stack backtraces, but this lucky report from Pawel Sikora hints that
mremap's move_ptes() has inadequate locking against page migration.
3.0 BUG_ON(!PageLocked(p)) in migration_entry_to_page():
kernel BUG at include/linux/swapops.h:105!
RIP: 0010:[<ffffffff81127b76>] [<ffffffff81127b76>]
migration_entry_wait+0x156/0x160
[<ffffffff811016a1>] handle_pte_fault+0xae1/0xaf0
[<ffffffff810feee2>] ? __pte_alloc+0x42/0x120
[<ffffffff8112c26b>] ? do_huge_pmd_anonymous_page+0xab/0x310
[<ffffffff81102a31>] handle_mm_fault+0x181/0x310
[<ffffffff81106097>] ? vma_adjust+0x537/0x570
[<ffffffff81424bed>] do_page_fault+0x11d/0x4e0
[<ffffffff81109a05>] ? do_mremap+0x2d5/0x570
[<ffffffff81421d5f>] page_fault+0x1f/0x30
mremap's down_write of mmap_sem, together with i_mmap_mutex or lock,
and pagetable locks, were good enough before page migration (with its
requirement that every migration entry be found) came in, and enough
while migration always held mmap_sem; but not enough nowadays, when
there's memory hotremove and compaction.
The danger is that move_ptes() lets a migration entry dodge around
behind remove_migration_pte()'s back, so it's in the old location when
looking at the new, then in the new location when looking at the old.
Either mremap's move_ptes() must additionally take anon_vma lock(), or
migration's remove_migration_pte() must stop peeking for is_swap_entry()
before it takes pagetable lock.
Consensus chooses the latter: we prefer to add overhead to migration
than to mremapping, which gets used by JVMs and by exec stack setup.
Reported-and-tested-by: Paweł Sikora <pluto@agmk.net>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently no type of alignment is specified for PCI expansion roms while
parsing the openfirmware tree. This causes calls to pci_map_rom() to fail.
IORESOURCE_SIZEALIGN is the default alignment used for rom resouces in
pci/probe.c, and has been verified to work with various cards on a ultra 10.
Signed-off-By: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the wrong parameter for setting EEE for RTL8111E-VL.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit 92fc43b415 ("r8169: modify the
flow of the hw reset."), rtl8169_hw_reset stomps during driver shutdown on
RxConfig bits which are needed for WOL on some versions of the hardware.
As these bits were formerly set from the r81{0x, 68}_pll_power_down methods,
factor them out for use in the driver shutdown (rtl_shutdown) handler.
I favored __rtl8169_get_wol() -hardware state indication- over
RTL_FEATURE_WOL as the latter has become a good candidate for removal.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Tested-by: Marc Ballarin <ballarin.marc@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/atom: fix handling of FB scratch indices
drm/radeon/kms/DCE4.1: fix Select_CrtcSource EncodeMode setting for DP bridges (v2)
drm/radeon/kms/DCE4.1: ss is not supported on the internal pplls
drm/radeon/kms/DCE4.1: fix dig encoder to transmitter mapping
ttm: Fix error-path using an uninitialized value
The change in 8280b66 does not cover the case when v4l2_dev is already
NULL, fix that.
With a Kinect sensor, seen as an USB camera using GSPCA in this context,
a NULL pointer dereference BUG can be triggered by just unplugging the
device after the camera driver has been loaded.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If target_level == 0, current code breaks out of the while-loop if
SUPERPAGE bit is set. We should also break out if PTE is not present.
If we don't do this, KVM calls to iommu_iova_to_phys() will cause
pfn_to_dma_pte() to create mapping for 4KiB pages.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
set dmar->iommu_superpage field to the smallest common denominator
of super page sizes supported by all active VT-d engines. Initialize
this field in intel_iommu_domain_init() API so intel_iommu_map() API
will be able to use iommu_superpage field to determine the appropriate
super page size to use.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
iommu_unmap() API expects IOMMU drivers to return the actual page order
of the address being unmapped. Previous code was just returning page
order passed in from the caller. This patch fixes this problem.
Signed-off-by: Allen Kay <allen.m.kay@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 166e9278a3 ("x86/ia64: intel-iommu: move to drivers/iommu/")
moved the VT-d driver to drivers/iommu, but left the "F:" line in
MAINTAINERS pointing to drivers/pci, which breaks scripts/get_maintainer.pl.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
FB scratch indices are dword indices, but we were treating
them as byte indices. As such, we were getting the wrong
FB scratch data for non-0 indices. Fix the indices and
guard the indexing against indices larger than the scratch
allocation.
Fixes memory corruption on some boards if data was written
past the end of the FB scratch array.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Dave Airlie <airlied@redhat.com>
Tested-by: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
e1000e uses paged frags, so any layer incorrectly pulling bytes from skb
can trigger a BUG in skb_pull()
[951.142737] [<ffffffff813d2f36>] skb_pull+0x15/0x17
[951.142737] [<ffffffffa0286824>] pptp_rcv_core+0x126/0x19a [pptp]
[951.152725] [<ffffffff813d17c4>] sk_receive_skb+0x69/0x105
[951.163558] [<ffffffffa0286993>] pptp_rcv+0xc8/0xdc [pptp]
[951.165092] [<ffffffffa02800a3>] gre_rcv+0x62/0x75 [gre]
[951.165092] [<ffffffff81410784>] ip_local_deliver_finish+0x150/0x1c1
[951.177599] [<ffffffff81410634>] ? ip_local_deliver_finish+0x0/0x1c1
[951.177599] [<ffffffff81410846>] NF_HOOK.clone.7+0x51/0x58
[951.177599] [<ffffffff81410996>] ip_local_deliver+0x51/0x55
[951.177599] [<ffffffff814105b9>] ip_rcv_finish+0x31a/0x33e
[951.177599] [<ffffffff8141029f>] ? ip_rcv_finish+0x0/0x33e
[951.204898] [<ffffffff81410846>] NF_HOOK.clone.7+0x51/0x58
[951.214651] [<ffffffff81410bb5>] ip_rcv+0x21b/0x246
pptp_rcv_core() is a nice example of a function assuming everything it
needs is available in skb head.
Reported-by: Bradley Peterson <despite@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transparent socket option setting was not copied to the time wait
socket when an inet socket was being replaced by a time wait socket. This
broke the --transparent option of the socket match and may have caused
that FIN packets belonging to sockets in FIN_WAIT2 or TIME_WAIT state
were being dropped by the packet filter.
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
