[ Upstream commit d39083234c ]
"f->fmt.sdr.reserved" is uninitialized. As other peer drivers
like msi2500 and airspy do, the fix initializes it to avoid
memory disclosures.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07066d9dc3 ]
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the ixgbe
driver still allowed TX packets to request HW timestamping. In this
situation, we see 'clearing Tx Timestamp hang' noise in the log.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Similar-to:
commit 26bd4e2db0 ("igb: protect TX timestamping from API misuse")
commit 0a6f2f05a2 ("igb: Fix a test with HWTSTAMP_TX_ON")
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6012b9346d ]
Instances may have flags set as part of its data in which case the code
should not attempt to add it again otherwise it can cause duplication:
< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
Handle: 0x00
Operation: Complete extended advertising data (0x03)
Fragment preference: Minimize fragmentation (0x01)
Data length: 0x06
Flags: 0x04
BR/EDR Not Supported
Flags: 0x06
LE General Discoverable Mode
BR/EDR Not Supported
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7bddfe2df ]
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function. The iio_triggered_buffer_predisable() hook is
called last (as is it should).
This change moves iio_triggered_buffer_postenable() to be called first. It
adds iio_triggered_buffer_predisable() on the error paths of the postenable
hook.
For the predisable hook, some code-paths have been changed to make sure
that the iio_triggered_buffer_predisable() hook gets called in case there
is an error before it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884caadad1 ]
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efcfec579f ]
Currently, if the loop device receives a WRITE_ZEROES request, it asks
the underlying filesystem to punch out the range. This behavior is
correct if unmapping is allowed. However, a NOUNMAP request means that
the caller doesn't want us to free the storage backing the range, so
punching out the range is incorrect behavior.
To satisfy a NOUNMAP | WRITE_ZEROES request, loop should ask the
underlying filesystem to FALLOC_FL_ZERO_RANGE, which is (according to
the fallocate documentation) required to ensure that the entire range is
backed by real storage, which suffices for our purposes.
Fixes: 19372e2769 ("loop: implement REQ_OP_WRITE_ZEROES")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 130f4caf14 ]
With CONFIG_DEBUG_TEST_DRIVER_REMOVE set, we may find the following WARN:
[ 23.452574] ------------[ cut here ]------------
[ 23.457190] WARNING: CPU: 59 PID: 1 at drivers/ata/libata-core.c:6676 ata_host_detach+0x15c/0x168
[ 23.466047] Modules linked in:
[ 23.469092] CPU: 59 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc1-00010-g5b83fd27752b-dirty #296
[ 23.477776] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.16.01 03/15/2019
[ 23.486286] pstate: a0c00009 (NzCv daif +PAN +UAO)
[ 23.491065] pc : ata_host_detach+0x15c/0x168
[ 23.495322] lr : ata_host_detach+0x88/0x168
[ 23.499491] sp : ffff800011cabb50
[ 23.502792] x29: ffff800011cabb50 x28: 0000000000000007
[ 23.508091] x27: ffff80001137f068 x26: ffff8000112c0c28
[ 23.513390] x25: 0000000000003848 x24: ffff0023ea185300
[ 23.518689] x23: 0000000000000001 x22: 00000000000014c0
[ 23.523987] x21: 0000000000013740 x20: ffff0023bdc20000
[ 23.529286] x19: 0000000000000000 x18: 0000000000000004
[ 23.534584] x17: 0000000000000001 x16: 00000000000000f0
[ 23.539883] x15: ffff0023eac13790 x14: ffff0023eb76c408
[ 23.545181] x13: 0000000000000000 x12: ffff0023eac13790
[ 23.550480] x11: ffff0023eb76c228 x10: 0000000000000000
[ 23.555779] x9 : ffff0023eac13798 x8 : 0000000040000000
[ 23.561077] x7 : 0000000000000002 x6 : 0000000000000001
[ 23.566376] x5 : 0000000000000002 x4 : 0000000000000000
[ 23.571674] x3 : ffff0023bf08a0bc x2 : 0000000000000000
[ 23.576972] x1 : 3099674201f72700 x0 : 0000000000400284
[ 23.582272] Call trace:
[ 23.584706] ata_host_detach+0x15c/0x168
[ 23.588616] ata_pci_remove_one+0x10/0x18
[ 23.592615] ahci_remove_one+0x20/0x40
[ 23.596356] pci_device_remove+0x3c/0xe0
[ 23.600267] really_probe+0xdc/0x3e0
[ 23.603830] driver_probe_device+0x58/0x100
[ 23.608000] device_driver_attach+0x6c/0x90
[ 23.612169] __driver_attach+0x84/0xc8
[ 23.615908] bus_for_each_dev+0x74/0xc8
[ 23.619730] driver_attach+0x20/0x28
[ 23.623292] bus_add_driver+0x148/0x1f0
[ 23.627115] driver_register+0x60/0x110
[ 23.630938] __pci_register_driver+0x40/0x48
[ 23.635199] ahci_pci_driver_init+0x20/0x28
[ 23.639372] do_one_initcall+0x5c/0x1b0
[ 23.643199] kernel_init_freeable+0x1a4/0x24c
[ 23.647546] kernel_init+0x10/0x108
[ 23.651023] ret_from_fork+0x10/0x18
[ 23.654590] ---[ end trace 634a14b675b71c13 ]---
With KASAN also enabled, we may also get many use-after-free reports.
The issue is that when CONFIG_DEBUG_TEST_DRIVER_REMOVE is set, we may
attempt to detach the ata_port before it has been probed.
This is because the ata_ports are async probed, meaning that there is no
guarantee that the ata_port has probed prior to detach. When the ata_port
does probe in this scenario, we get all sorts of issues as the detach may
have already happened.
Fix by ensuring synchronisation with async_synchronize_full(). We could
alternatively use the cookie returned from the ata_port probe
async_schedule() call, but that means managing the cookie, so more
complicated.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 647522a5ef ]
When there is a TX timeout, we can tell if the driver or stack
has stopped the queue by looking at state field, and when has
the last packet transmited by looking at trans_start field.
So this patch prints these two field in the
hns3_get_tx_timeo_queue_info().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2416cefc50 ]
Unlike pxd_free_tlb(), the pxd_free() functions do not check for folded
page tables. This is not an issue so far, as those functions will actually
never be called, since no code will reach them when page tables are folded.
In order to avoid future issues, and to make the s390 code more similar to
other architectures, add mm_pxd_folded() checks, similar to how it is done
in pxd_free_tlb().
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add tests validating architecture
page table helpers").
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 011620688a ]
The current implementation of get_clock_monotonic() leaves it up to
the caller to call the function with preemption disabled. The only
core kernel caller (sched_clock) however does not disable preemption.
In order to make sure that all callers of this function see monotonic
values handle disabling preemption within the function itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64f86b9978 ]
Commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
switched from extcon_register_notifier() to the resource-managed
API, i.e. devm_extcon_register_notifier().
This is problematic in this case, because the extcon notifier
is dynamically registered/unregistered whenever the PHY is powered
on/off. The resource-managed API does not unregister the notifier
until the driver is removed, so as soon as the PHY is power cycled,
attempting to register the notifier again results in:
double register detected
WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0
Call trace:
...
extcon_register_notifier+0x74/0xb8
devm_extcon_register_notifier+0x54/0xb8
qcom_usb_hs_phy_power_on+0x1fc/0x208
...
... and USB stops working after plugging the cable out and in
another time.
The easiest way to fix this is to make a partial revert of
commit f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
and avoid using the resource-managed API in this case.
Fixes: f0b5c2c963 ("phy: qcom-usb-hs: Replace the extcon API")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6989d248a ]
When NET_DSA_SMSC_LAN9303=y and NET_DSA_SMSC_LAN9303_MDIO=y,
below errors can be seen:
drivers/net/dsa/lan9303_mdio.c:87:23: error: REGMAP_ENDIAN_LITTLE
undeclared here (not in a function)
.reg_format_endian = REGMAP_ENDIAN_LITTLE,
drivers/net/dsa/lan9303_mdio.c:93:3: error: const struct regmap_config
has no member named reg_read
.reg_read = lan9303_mdio_read,
It should select REGMAP in config NET_DSA_SMSC_LAN9303.
Fixes: dc70058315 ("net: dsa: LAN9303: add MDIO managed mode support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b78e70c04c ]
Currently when the gather buffers are copied, they are copied to a
buffer that is allocated for the host1x client that wants to execute the
command streams in the buffers. However, the gather buffers will be read
by the host1x device, which causes SMMU faults if the DMA API is backed
by an IOMMU.
Fix this by allocating the gather buffer copy for the host1x device,
which makes sure that it will be mapped into the host1x's IOVA space if
the DMA API is backed by an IOMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 932e1ba486 ]
The Medion Akoya E2215T's ACPI _LID implementation is quite broken:
1. For notifications it uses an ActiveLow Edge GpioInt, rather then
an ActiveBoth one, meaning that the device is only notified when the
lid is closed, not when it is opened.
2. Matching with this its _LID method simply always returns 0 (closed)
In order for the Linux LID code to work properly with this implementation,
the lid_init_state selection needs to be set to ACPI_BUTTON_LID_INIT_OPEN.
This commit adds a DMI quirk for this.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24e64f86da ]
The device tree bindings for the Tegra210 SOR don't require the
controller instance to be defined, since the instance can be derived
from the compatible string. The index is never used on Tegra210, so we
got away with it not getting set. However, subsequent patches will
change that, so make sure the proper index is used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7f08c2ab ]
The link detection timeouts can be observed (or link might not be detected
at all) when dp83867 PHY is configured in manual mode (speed/duplex).
CFG3[9] Robust Auto-MDIX option allows to significantly improve link detection
in case dp83867 is configured in manual mode and reduce link detection
time.
As per DM: "If link partners are configured to operational modes that are
not supported by normal Auto MDI/MDIX mode (like Auto-Neg versus Force
100Base-TX or Force 100Base-TX versus Force 100Base-TX), this Robust Auto
MDI/MDIX mode allows MDI/MDIX resolution and prevents deadlock."
Hence, enable this option by default as there are no known reasons
not to do so.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 998e5166e6 ]
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN/ITR0 registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfcef4ab1d ]
In cases like suspend-to-disk and suspend-to-ram, a large number of CPU
cores need to be shut down. At present, the CPU hotplug operation is
serialised, and the CPU cores can only be shut down one by one. In this
process, if PSCI affinity_info() does not return LEVEL_OFF quickly,
cpu_psci_cpu_kill() needs to wait for 10ms. If hundreds of CPU cores
need to be shut down, it will take a long time.
Normally, there is no need to wait 10ms in cpu_psci_cpu_kill(). So
change the wait interval from 10 ms to max 1 ms and use usleep_range()
instead of msleep() for more accurate timer.
In addition, reducing the time interval will increase the messages
output, so remove the "Retry ..." message, instead, track time and
output to the the sucessful message.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90c9e4a4db ]
Earlier it was possible that the parts of the driver that assumed runtime
PM was enabled were being called before runtime PM was enabled in the
driver's probe function. So enable runtime PM before registering the
sub-device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df4393424a ]
There is an issue with threaded interrupts which are marked ONESHOT
and using the fasteoi handler:
if (IS_ONESHOT())
mask_irq();
....
cond_unmask_eoi_irq()
chip->irq_eoi();
if (setaffinity_pending) {
mask_ioapic();
...
move_affinity();
unmask_ioapic();
}
So if setaffinity is pending the interrupt will be moved and then
unconditionally unmasked at the ioapic level, which is wrong in two
aspects:
1) It should be kept masked up to the point where the threaded handler
finished.
2) The physical chip state and the software masked state are inconsistent
Guard both the mask and the unmask with a check for the software masked
state. If the line is marked masked then the ioapic line is also masked, so
both mask_ioapic() and unmask_ioapic() can be skipped safely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Fixes: 3aa551c9b4 ("genirq: add threaded interrupt handler support")
Link: https://lkml.kernel.org/r/20191017101938.321393687@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbb79863fc ]
If something has the IPMI driver open, don't allow the device
module to be unloaded. Before it would unload and the user would
get errors on use.
This change is made on user request, and it makes it consistent
with the I2C driver, which has the same behavior.
It does change things a little bit with respect to kernel users.
If the ACPI or IPMI watchdog (or any other kernel user) has
created a user, then the device module cannot be unloaded. Before
it could be unloaded,
This does not affect hot-plug. If the device goes away (it's on
something removable that is removed or is hot-removed via sysfs)
then it still behaves as it did before.
Reported-by: tony camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: tony camuso <tcamuso@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eeb91ade9 ]
The RTL8723BU has problems connecting to AP after each warm reboot.
Sometimes it returns no scan result, and in most cases, it fails
the authentication for unknown reason. However, it works totally
fine after cold reboot.
Compare the value of register SYS_CR and SYS_CLK_MAC_CLK_ENABLE
for cold reboot and warm reboot, the registers imply that the MAC
is already powered and thus some procedures are skipped during
driver initialization. Double checked the vendor driver, it reads
the SYS_CR and SYS_CLK_MAC_CLK_ENABLE also but doesn't skip any
during initialization based on them. This commit only tells the
RTL8723BU to do full initialization without checking MAC status.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a5f3d94cb ]
As there are several discussions for enabling perf breakpoint signal
testing on arm64 platform: arm64 needs to rely on single-step to execute
the breakpointed instruction and then reinstall the breakpoint exception
handler. But if we hook the breakpoint with a signal, the signal
handler will do the stepping rather than the breakpointed instruction,
this causes infinite loops as below:
Kernel space | Userspace
---------------------------------|--------------------------------
| __test_function() -> hit
| breakpoint
breakpoint_handler() |
`-> user_enable_single_step() |
do_signal() |
| sig_handler() -> Step one
| instruction and
| trap to kernel
single_step_handler() |
`-> reinstall_suspended_bps() |
| __test_function() -> hit
| breakpoint again and
| repeat up flow infinitely
As Will Deacon mentioned [1]: "that we require the overflow handler to
do the stepping on arm/arm64, which is relied upon by GDB/ptrace. The
hw_breakpoint code is a complete disaster so my preference would be to
rip out the perf part and just implement something directly in ptrace,
but it's a pretty horrible job". Though Will commented this on arm
architecture, but the comment also can apply on arm64 architecture.
For complete information, I searched online and found a few years back,
Wang Nan sent one patch 'arm64: Store breakpoint single step state into
pstate' [2]; the patch tried to resolve this issue by avoiding single
stepping in signal handler and defer to enable the signal stepping when
return to __test_function(). The fixing was not merged due to the
concern for missing to handle different usage cases.
Based on the info, the most feasible way is to skip Perf breakpoint
signal testing for arm64 and this could avoid the duplicate
investigation efforts when people see the failure. This patch skips
this case on arm64 platform, which is same with arm architecture.
[1] https://lkml.org/lkml/2018/11/15/205
[2] https://lkml.org/lkml/2015/12/23/477
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lore.kernel.org/lkml/20191018085531.6348-3-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c3bafaa1f ]
On modern CPUs it is quite normal that the temperature limits are
reached and the CPU is throttled. In fact, often the thermal design is
not sufficient to cool the CPU at full load and limits can quickly be
reached when a burst in load happens. This will even happen with
technologies like RAPL limitting the long term power consumption of
the package.
Also, these limits are "softer", as Srinivas explains:
"CPU temperature doesn't have to hit max(TjMax) to get these warnings.
OEMs ha[ve] an ability to program a threshold where a thermal interrupt
can be generated. In some systems the offset is 20C+ (Read only value).
In recent systems, there is another offset on top of it which can be
programmed by OS, once some agent can adjust power limits dynamically.
By default this is set to low by the firmware, which I guess the
prime motivation of Benjamin to submit the patch."
So these messages do not usually indicate a hardware issue (e.g.
insufficient cooling). Log them as warnings to avoid confusion about
their severity.
[ bp: Massage commit mesage. ]
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Christian Kellner <ckellner@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191009155424.249277-1-bberg@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eac9153f2b ]
bpf stackmap with build-id lookup (BPF_F_STACK_BUILD_ID) can trigger A-A
deadlock on rq_lock():
rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[...]
Call Trace:
try_to_wake_up+0x1ad/0x590
wake_up_q+0x54/0x80
rwsem_wake+0x8a/0xb0
bpf_get_stack+0x13c/0x150
bpf_prog_fbdaf42eded9fe46_on_event+0x5e3/0x1000
bpf_overflow_handler+0x60/0x100
__perf_event_overflow+0x4f/0xf0
perf_swevent_overflow+0x99/0xc0
___perf_sw_event+0xe7/0x120
__schedule+0x47d/0x620
schedule+0x29/0x90
futex_wait_queue_me+0xb9/0x110
futex_wait+0x139/0x230
do_futex+0x2ac/0xa50
__x64_sys_futex+0x13c/0x180
do_syscall_64+0x42/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This can be reproduced by:
1. Start a multi-thread program that does parallel mmap() and malloc();
2. taskset the program to 2 CPUs;
3. Attach bpf program to trace_sched_switch and gather stackmap with
build-id, e.g. with trace.py from bcc tools:
trace.py -U -p <pid> -s <some-bin,some-lib> t:sched:sched_switch
A sample reproducer is attached at the end.
This could also trigger deadlock with other locks that are nested with
rq_lock.
Fix this by checking whether irqs are disabled. Since rq_lock and all
other nested locks are irq safe, it is safe to do up_read() when irqs are
not disable. If the irqs are disabled, postpone up_read() in irq_work.
Fixes: 615755a77b ("bpf: extend stackmap to save binary_build_id+offset instead of address")
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191014171223.357174-1-songliubraving@fb.com
Reproducer:
============================ 8< ============================
char *filename;
void *worker(void *p)
{
void *ptr;
int fd;
char *pptr;
fd = open(filename, O_RDONLY);
if (fd < 0)
return NULL;
while (1) {
struct timespec ts = {0, 1000 + rand() % 2000};
ptr = mmap(NULL, 4096 * 64, PROT_READ, MAP_PRIVATE, fd, 0);
usleep(1);
if (ptr == MAP_FAILED) {
printf("failed to mmap\n");
break;
}
munmap(ptr, 4096 * 64);
usleep(1);
pptr = malloc(1);
usleep(1);
pptr[0] = 1;
usleep(1);
free(pptr);
usleep(1);
nanosleep(&ts, NULL);
}
close(fd);
return NULL;
}
int main(int argc, char *argv[])
{
void *ptr;
int i;
pthread_t threads[THREAD_COUNT];
if (argc < 2)
return 0;
filename = argv[1];
for (i = 0; i < THREAD_COUNT; i++) {
if (pthread_create(threads + i, NULL, worker, NULL)) {
fprintf(stderr, "Error creating thread\n");
return 0;
}
}
for (i = 0; i < THREAD_COUNT; i++)
pthread_join(threads[i], NULL);
return 0;
}
============================ 8< ============================
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb8c101e28 ]
During the setup() stage, HCI device drivers expect the chip to
acknowledge its setup() completion via vendor specific frames.
If userspace opens() such HCI device in HCI_USER_CHANNEL [1] mode,
the vendor specific frames are never tranmitted to the driver, as
they are filtered in hci_rx_work().
Allow HCI devices which operate in HCI_USER_CHANNEL mode to receive
frames if the HCI device is is HCI_INIT state.
[1] https://www.spinics.net/lists/linux-bluetooth/msg37345.html
Fixes: 23500189d7 ("Bluetooth: Introduce new HCI socket channel for user operation")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c371bb95c ]
It appears that some Broadcom controllers (eg BCM20702A0) reject LE Set
Advertising Parameters command if advertising intervals provided are not
within range for undirected and low duty directed advertising.
Workaround this bug by populating min and max intervals with 'valid'
values.
< HCI Command: LE Set Advertising Parameters (0x08|0x0006) plen 15
Min advertising interval: 0.000 msec (0x0000)
Max advertising interval: 0.000 msec (0x0000)
Type: Connectable directed - ADV_DIRECT_IND (high duty cycle) (0x01)
Own address type: Public (0x00)
Direct address type: Random (0x01)
Direct address: E2:F0:7B:9F:DC:F4 (Static)
Channel map: 37, 38, 39 (0x07)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Parameters (0x08|0x0006) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Sören Beye <linux@hypfer.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 727ea61a50 ]
It looks like in hci_init4_req() the request is being
initialised from cpu-endian data but the packet is specified
to be little-endian. This causes an warning from sparse due
to __le16 to u16 conversion.
Fix this by using cpu_to_le16() on the two fields in the packet.
net/bluetooth/hci_core.c:845:27: warning: incorrect type in assignment (different base types)
net/bluetooth/hci_core.c:845:27: expected restricted __le16 [usertype] tx_len
net/bluetooth/hci_core.c:845:27: got unsigned short [usertype] le_max_tx_len
net/bluetooth/hci_core.c:846:28: warning: incorrect type in assignment (different base types)
net/bluetooth/hci_core.c:846:28: expected restricted __le16 [usertype] tx_time
net/bluetooth/hci_core.c:846:28: got unsigned short [usertype] le_max_tx_time
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db033831b4 ]
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abb0b3d96a ]
commit 1455cf8dbf ("driver core: emit uevents when device is bound
to a driver") added bind and unbind uevents when a driver is bound or
unbound to a physical device.
For USB devices which are handled via the generic usbfs layer (via
libusb for example), this is problematic:
Each time a user space program calls
ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr);
and then later
ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr);
The kernel will now produce a bind or unbind event, which does not
really contain any useful information.
This allows a user space program to run a DoS attack against programs
which listen to uevents (in particular systemd/eudev/upowerd):
A malicious user space program just has to call in a tight loop
ioctl(usb_fd, USBDEVFS_CLAIMINTERFACE, &usb_intf_nr);
ioctl(usb_fd, USBDEVFS_RELEASEINTERFACE, &usb_intf_nr);
With this loop the malicious user space program floods the kernel and
all programs listening to uevents with tons of bind and unbind
events.
This patch suppresses uevents for ioctls USBDEVFS_CLAIMINTERFACE and
USBDEVFS_RELEASEINTERFACE.
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Link: https://lore.kernel.org/r/20191011115518.2801-1-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d43810b2c1 ]
The return value of dma_map_single() should be checked for errors using
dma_mapping_error() and the skb has been dequeued so it needs to be
freed.
This was found when enabling CONFIG_DMA_API_DEBUG and it warned about the
missing dma_mapping_error() call.
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6942635032 ]
On some devices (e.g. Samsung Galaxy A5 (2015)), the bootloader
seems to keep interrupts enabled for SM5502 when booting Linux.
Changing the cable state (i.e. plugging in a cable) - until the driver
is loaded - will therefore produce an interrupt that is never read.
In this situation, the cable state will be stuck forever on the
initial state because SM5502 stops sending interrupts.
This can be avoided by clearing those pending interrupts after
the driver has been loaded.
One way to do this is to reset all registers to default state
by writing to SM5502_REG_RESET. This ensures that we start from
a clean state, with all interrupts disabled.
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd998291db ]
[WHY]
During detection:
function: get_active_converter_info populates link->dpcd_caps.dongle_caps
only when dpcd_rev >= DPCD_REV_11 and DWN_STRM_PORTX_TYPE is
DOWN_STREAM_DETAILED_HDMI or DOWN_STREAM_DETAILED_DP_PLUS_PLUS.
Otherwise, it is not cleared, and stale information remains.
During mode validation:
function: dp_active_dongle_validate_timing reads
link->dpcd_caps.dongle_caps->dongle_type to determine the maximum
pixel clock to support. This information is now stale and no longer
valid.
[HOW]
dp_active_dongle_validate_timing should be using
link->dpcd_caps->dongle_type instead.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bac73adea ]
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(463): !pfmt.sizeimage
fail: v4l2-test-formats.cpp(736): \
Video Capture Multiplanar is valid, \
but TRY_FMT failed to return a format
test VIDIOC_TRY_FMT: FAIL
This failure is causd by the driver failing to handle out range
'bytesperline' values from user space applications.
VPDMA hardware is limited to 64k line stride (16 bytes aligned, so 65520
bytes). So make sure the provided or calculated 'bytesperline' is
smaller than the maximum value.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf6acb73b0 ]
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(691): ret == 0
fail: v4l2-test-buffers.cpp(974): captureBufs(node, q, m2m_q,
frame_count, true)
test MMAP: FAIL
This caused the following Kernel Warning:
WARNING: CPU: 0 PID: 961 at
drivers/media/v4l2-core/videobuf2-core.c:1658
__vb2_queue_cancel+0x174/0x1d8
...
CPU: 0 PID: 961 Comm: v4l2-compliance Not tainted
4.14.62-01720-g20ecd717e87a #6
Hardware name: Generic DRA72X (Flattened Device Tree)
Backtrace:
[<c020b5bc>] (dump_backtrace) from [<c020b8a0>] (show_stack+0x18/0x1c)
r7:00000009 r6:60070013 r5:00000000 r4:c1053824
[<c020b888>] (show_stack) from [<c09232e8>] (dump_stack+0x90/0xa4)
[<c0923258>] (dump_stack) from [<c022b740>] (__warn+0xec/0x104)
r7:00000009 r6:c0c0ad50 r5:00000000 r4:00000000
[<c022b654>] (__warn) from [<c022b810>] (warn_slowpath_null+0x28/0x30)
r9:00000008 r8:00000000 r7:eced4808 r6:edbc9bac r5:eced4844
r4:eced4808
[<c022b7e8>] (warn_slowpath_null) from [<c0726f48>]
(__vb2_queue_cancel+0x174/0x1d8)
[<c0726dd4>] (__vb2_queue_cancel) from [<c0727648>]
(vb2_core_queue_release+0x20/0x40)
r10:ecc7bd70 r9:00000008 r8:00000000 r7:edb73010 r6:edbc9bac
r5:eced4844
r4:eced4808 r3:00000004
[<c0727628>] (vb2_core_queue_release) from [<c0729528>]
(vb2_queue_release+0x10/0x14)
r5:edbc9810 r4:eced4800
[<c0729518>] (vb2_queue_release) from [<c0724d08>]
(v4l2_m2m_ctx_release+0x1c/0x30)
[<c0724cec>] (v4l2_m2m_ctx_release) from [<bf0e8f28>]
(vpe_release+0x74/0xb0 [ti_vpe])
r5:edbc9810 r4:ed67a400
[<bf0e8eb4>] (vpe_release [ti_vpe]) from [<c070fccc>]
(v4l2_release+0x3c/0x80)
r7:edb73010 r6:ed176aa0 r5:edbc9868 r4:ed5119c0
[<c070fc90>] (v4l2_release) from [<c033cf1c>] (__fput+0x8c/0x1dc)
r5:ecc7bd70 r4:ed5119c0
[<c033ce90>] (__fput) from [<c033d0cc>] (____fput+0x10/0x14)
r10:00000000 r9:ed5119c0 r8:ece392d0 r7:c1059544 r6:ece38d80
r5:ece392b4
r4:00000000
[<c033d0bc>] (____fput) from [<c0246e00>] (task_work_run+0x98/0xb8)
[<c0246d68>] (task_work_run) from [<c022f1d8>] (do_exit+0x170/0xa80)
r9:ece351fc r8:00000000 r7:ecde3f58 r6:ffffe000 r5:ece351c0
r4:ece38d80
[<c022f068>] (do_exit) from [<c022fb6c>] (do_group_exit+0x48/0xc4)
r7:000000f8
[<c022fb24>] (do_group_exit) from [<c022fc00>]
(__wake_up_parent+0x0/0x28)
r7:000000f8 r6:b6c6a798 r5:00000001 r4:00000001
[<c022fbe8>] (SyS_exit_group) from [<c0207c80>]
(ret_fast_syscall+0x0/0x4c)
These warnings are caused by buffers which not properly cleaned
up/release during an abort use case.
In the abort cases the VPDMA desc buffers would still be mapped and the
in-flight VB2 buffers would not be released properly causing a kernel
warning from being generated by the videobuf2-core level.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a37980ac5b ]
v4l2-compliance fails with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
test VIDIOC_TRY_FMT: FAIL
This causes the following kernel panic:
Unable to handle kernel paging request at virtual address 56595561
pgd = ecd80e00
*pgd=00000000
Internal error: Oops: 205 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 930 Comm: v4l2-compliance Not tainted \
4.14.62-01715-gc8cd67f49a19 #1
Hardware name: Generic DRA72X (Flattened Device Tree)
task: ece44d80 task.stack: ecc6e000
PC is at __vpe_try_fmt+0x18c/0x2a8 [ti_vpe]
LR is at 0x8
Because the driver fails to properly check the 'num_planes' values for
proper ranges it ends up accessing out of bound data causing the kernel
panic.
Since this driver only handle single or dual plane pixel format, make
sure the provided value does not exceed 2 planes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e20b248051 ]
v4l2-compliance fails with this message:
fail: v4l2-test-formats.cpp(672): \
Video Capture Multiplanar: TRY_FMT(G_FMT) != G_FMT
fail: v4l2-test-formats.cpp(672): \
Video Output Multiplanar: TRY_FMT(G_FMT) != G_FMT
...
test VIDIOC_TRY_FMT: FAIL
The default pixel format was setup as pointing to a specific offset in
the vpe_formats table assuming it was pointing to the V4L2_PIX_FMT_YUYV
entry. This became false after the addition on the NV21 format (see
above commid-id)
So instead of hard-coding an offset which might change over time we need
to use a lookup helper instead so we know the default will always be what
we intended.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Fixes: 40cc823f7005 ("media: ti-vpe: Add support for NV21 format")
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2444846c0d ]
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(294): \
(int)g_sequence() < seq.last_seq + 1
fail: v4l2-test-buffers.cpp(740): \
buf.check(m2m_q, last_m2m_seq)
fail: v4l2-test-buffers.cpp(974): \
captureBufs(node, q, m2m_q, frame_count, true)
test MMAP: FAIL
The driver is failing to update the source frame sequence number in the
vb2 buffer object. Only the destination frame sequence was being
updated.
This is only a reporting issue if the user space app actually cares
about the frame sequence number. But it is fixed nonetheless.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06bec72b25 ]
v4l2-compliance warns with this message:
warn: v4l2-test-formats.cpp(717): \
TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(718): \
This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(719): \
http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
...
test VIDIOC_TRY_FMT: FAIL
We need to make sure that the returns a valid pixel format in all
instance. Based on the v4l2 framework convention drivers must return a
valid pixel format when the requested pixel format is either invalid or
not supported.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
