[ Upstream commit 33309ecda0 ]
The dcache_by_line_op macro suffers from a couple of small problems:
First, the GAS directives that are currently being used rely on
assembler behavior that is not documented, and probably not guaranteed
to produce the correct behavior going forward. As a result, we end up
with some undefined symbols in cache.o:
$ nm arch/arm64/mm/cache.o
...
U civac
...
U cvac
U cvap
U cvau
This is due to the fact that the comparisons used to select the
operation type in the dcache_by_line_op macro are comparing symbols
not strings, and even though it seems that GAS is doing the right
thing here (undefined symbols by the same name are equal to each
other), it seems unwise to rely on this.
Second, when patching in a DC CVAP instruction on CPUs that support it,
the fallback path consists of a DC CVAU instruction which may be
affected by CPU errata that require ARM64_WORKAROUND_CLEAN_CACHE.
Solve these issues by unrolling the various maintenance routines and
using the conditional directives that are documented as operating on
strings. To avoid the complexity of nested alternatives, we move the
DC CVAP patching to __clean_dcache_area_pop, falling back to a branch
to __clean_dcache_area_poc if DCPOP is not supported by the CPU.
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7542d8177 ]
The exclusive gates may be set up in the wrong way by software running
before the clock driver comes up. In that case the exclusive setup is
locked in its initial state, as the complementary function can't be
activated without disabling the initial setup first.
To avoid this lock situation, reset the exclusive gates to the off
state and allow the kernel to provide the proper setup.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e8830674e ]
If the kernel is configured with KASAN_EXTRA, the stack size is
increased significantly due to setting the GCC -fstack-reuse option to
"none" [1]. As a result, it can trigger a stack overrun quite often with
32k stack size compiled using GCC 8. For example, this reproducer
https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/syscalls/madvise/madvise06.c
can trigger a "corrupted stack end detected inside scheduler" very
reliably with CONFIG_SCHED_STACK_END_CHECK enabled. There are other
reports at:
https://lore.kernel.org/lkml/1542144497.12945.29.camel@gmx.us/https://lore.kernel.org/lkml/721E7B42-2D55-4866-9C1A-3E8D64F33F9C@gmx.us/
There are just too many functions that could have a large stack with
KASAN_EXTRA due to large local variables that have been called over and
over again without being able to reuse the stacks. Some noticiable ones
are,
size
7536 shrink_inactive_list
7440 shrink_page_list
6560 fscache_stats_show
3920 jbd2_journal_commit_transaction
3216 try_to_unmap_one
3072 migrate_page_move_mapping
3584 migrate_misplaced_transhuge_page
3920 ip_vs_lblcr_schedule
4304 lpfc_nvme_info_show
3888 lpfc_debugfs_nvmestat_data.constprop
There are other 49 functions over 2k in size while compiling kernel with
"-Wframe-larger-than=" on this machine. Hence, it is too much work to
change Makefiles for each object to compile without
-fsanitize-address-use-after-scope individually.
[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715#c23
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b708a3cc96 ]
I've stumbled over the current macro-expand behaviour of the test
harness:
$ gcc -Wall -xc - <<'__EOF__'
TEST(macro) {
int status = 0;
ASSERT_TRUE(WIFSIGNALED(status));
}
TEST_HARNESS_MAIN
__EOF__
$ ./a.out
[==========] Running 1 tests from 1 test cases.
[ RUN ] global.macro
<stdin>:4:global.macro:Expected 0 (0) != (((signed char) (((status) & 0x7f) + 1) >> 1) > 0) (0)
global.macro: Test terminated by assertion
[ FAIL ] global.macro
[==========] 0 / 1 tests passed.
[ FAILED ]
With this change the output of the same test looks much more
comprehensible:
[==========] Running 1 tests from 1 test cases.
[ RUN ] global.macro
<stdin>:4:global.macro:Expected 0 (0) != WIFSIGNALED(status) (0)
global.macro: Test terminated by assertion
[ FAIL ] global.macro
[==========] 0 / 1 tests passed.
[ FAILED ]
The issue is very similar to the bug fixed in glibc assert(3)
three years ago:
https://sourceware.org/bugzilla/show_bug.cgi?id=18604
Cc: Shuah Khan <shuah@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Cc: linux-kselftest@vger.kernel.org
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad669505c4 ]
A session must only be released after all code that accesses the session
structure has finished. Make sure that this is the case by introducing a
new command counter per session that is only decremented after the
.release_cmd() callback has finished. This patch fixes the following crash:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x1c/0x130
Read of size 4 at addr ffff8801534b16e4 by task rmdir/14805
CPU: 16 PID: 14805 Comm: rmdir Not tainted 4.18.0-rc2-dbg+ #5
Call Trace:
dump_stack+0xa4/0xf5
print_address_description+0x6f/0x270
kasan_report+0x241/0x360
__asan_load4+0x78/0x80
do_raw_spin_lock+0x1c/0x130
_raw_spin_lock_irqsave+0x52/0x60
srpt_set_ch_state+0x27/0x70 [ib_srpt]
srpt_disconnect_ch+0x1b/0xc0 [ib_srpt]
srpt_close_session+0xa8/0x260 [ib_srpt]
target_shutdown_sessions+0x170/0x180 [target_core_mod]
core_tpg_del_initiator_node_acl+0xf3/0x200 [target_core_mod]
target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
config_item_release+0x9c/0x110 [configfs]
config_item_put+0x26/0x30 [configfs]
configfs_rmdir+0x3b8/0x510 [configfs]
vfs_rmdir+0xb3/0x1e0
do_rmdir+0x262/0x2c0
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0de263577d ]
spc5r17.pdf specifies:
4.3.1 ASCII data field requirements
ASCII data fields shall contain only ASCII printable characters (i.e.,
code values 20h to 7Eh) and may be terminated with one or more ASCII null
(00h) characters. ASCII data fields described as being left-aligned
shall have any unused bytes at the end of the field (i.e., highest
offset) and the unused bytes shall be filled with ASCII space characters
(20h).
LIO currently space-pads the T10 VENDOR IDENTIFICATION and PRODUCT
IDENTIFICATION fields in the standard INQUIRY data. However, the PRODUCT
REVISION LEVEL field in the standard INQUIRY data as well as the T10 VENDOR
IDENTIFICATION field in the INQUIRY Device Identification VPD Page are
zero-terminated/zero-padded.
Fix this inconsistency by using space-padding for all of the above fields.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bryant G. Ly <bly@catalogicsoftware.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fbe82e628 ]
after set SO_DONTROUTE to 1, the IP layer should not route packets if
the dest IP address is not in link scope. But if the socket has cached
the dst_entry, such packets would be routed until the sk_dst_cache
expires. So we should clean the sk_dst_cache when a user set
SO_DONTROUTE option. Below are server/client python scripts which
could reprodue this issue:
server side code:
==========================================================================
import socket
import struct
import time
s = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
s.bind(('0.0.0.0', 9000))
s.listen(1)
sock, addr = s.accept()
sock.setsockopt(socket.SOL_SOCKET, socket.SO_DONTROUTE, struct.pack('i', 1))
while True:
sock.send(b'foo')
time.sleep(1)
==========================================================================
client side code:
==========================================================================
import socket
import time
s = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
s.connect(('server_address', 9000))
while True:
data = s.recv(1024)
print(data)
==========================================================================
Signed-off-by: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23aa128bb2 ]
AMD platform device acp_audio_dma can only be created by parent PCI
device driver (drivers/gpu/drm/amd/amdgpu/amdgpu_acp.c). Pass struct
device of the parent to snd_pcm_lib_preallocate_pages() so
dma_alloc_coherent() can use correct dma_ops. Otherwise, it will
use default dma_ops which is nommu_dma_ops on x86_64 even when
IOMMU is enabled and set to non passthrough mode.
Though platform device inherits some dma related fields during its
creation in mfd_add_device(), we can't simply pass its struct device
to snd_pcm_lib_preallocate_pages() because dma_ops is not among the
inherited fields. Even it were, drivers/iommu/amd_iommu.c would
ignore it because get_device_id() doesn't handle platform device.
This change shouldn't give us any trouble even struct device of the
parent becomes null or represents some non PCI device in the future,
because get_dma_ops() correctly handles null struct device or uses
the default dma_ops if struct device doesn't have it set.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2e9a4eda1 ]
Clang warns:
drivers/media/firewire/firedtv-avc.c:999:45: warning: implicit
conversion from 'int' to 'char' changes value from 159 to -97
[-Wconstant-conversion]
app_info[0] = (EN50221_TAG_APP_INFO >> 16) & 0xff;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
drivers/media/firewire/firedtv-avc.c:1000:45: warning: implicit
conversion from 'int' to 'char' changes value from 128 to -128
[-Wconstant-conversion]
app_info[1] = (EN50221_TAG_APP_INFO >> 8) & 0xff;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
drivers/media/firewire/firedtv-avc.c:1040:44: warning: implicit
conversion from 'int' to 'char' changes value from 159 to -97
[-Wconstant-conversion]
app_info[0] = (EN50221_TAG_CA_INFO >> 16) & 0xff;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
drivers/media/firewire/firedtv-avc.c:1041:44: warning: implicit
conversion from 'int' to 'char' changes value from 128 to -128
[-Wconstant-conversion]
app_info[1] = (EN50221_TAG_CA_INFO >> 8) & 0xff;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
4 warnings generated.
Change app_info's type to unsigned char to match the type of the
member msg in struct ca_msg, which is the only thing passed into the
app_info parameter in this function.
Link: https://github.com/ClangBuiltLinux/linux/issues/105
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b038cbc5f ]
When booting a pseries kernel with PREEMPT enabled, it dumps the
following warning:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is pseries_processor_idle_init+0x5c/0x22c
CPU: 13 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc3-00090-g12201a0128bc-dirty #828
Call Trace:
[c000000429437ab0] [c0000000009c8878] dump_stack+0xec/0x164 (unreliable)
[c000000429437b00] [c0000000005f2f24] check_preemption_disabled+0x154/0x160
[c000000429437b90] [c000000000cab8e8] pseries_processor_idle_init+0x5c/0x22c
[c000000429437c10] [c000000000010ed4] do_one_initcall+0x64/0x300
[c000000429437ce0] [c000000000c54500] kernel_init_freeable+0x3f0/0x500
[c000000429437db0] [c0000000000112dc] kernel_init+0x2c/0x160
[c000000429437e20] [c00000000000c1d0] ret_from_kernel_thread+0x5c/0x6c
This happens because the code calls get_lppaca() which calls
get_paca() and it checks if preemption is disabled through
check_preemption_disabled().
Preemption should be disabled because the per CPU variable may make no
sense if there is a preemption (and a CPU switch) after it reads the
per CPU data and when it is used.
In this device driver specifically, it is not a problem, because this
code just needs to have access to one lppaca struct, and it does not
matter if it is the current per CPU lppaca struct or not (i.e. when
there is a preemption and a CPU migration).
That said, the most appropriate fix seems to be related to avoiding
the debug_smp_processor_id() call at get_paca(), instead of calling
preempt_disable() before get_paca().
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d4a862276 ]
Currently xmon needs to get devtree_lock (through rtas_token()) during its
invocation (at crash time). If there is a crash while devtree_lock is being
held, then xmon tries to get the lock but spins forever and never get into
the interactive debugger, as in the following case:
int *ptr = NULL;
raw_spin_lock_irqsave(&devtree_lock, flags);
*ptr = 0xdeadbeef;
This patch avoids calling rtas_token(), thus trying to get the same lock,
at crash time. This new mechanism proposes getting the token at
initialization time (xmon_init()) and just consuming it at crash time.
This would allow xmon to be possible invoked independent of devtree_lock
being held or not.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10e1fdb958 ]
Currently, disconnecting a USB webcam while it is in use prints out a
number of warnings, such as:
WARNING: CPU: 2 PID: 3118 at /build/linux-ezBi1T/linux-4.8.0/fs/sysfs/group.c:237 sysfs_remove_group+0x8b/0x90
sysfs group ffffffffa7cd0780 not found for kobject 'event13'
This has been noticed before. [0]
This is because of the order in which things are torn down.
If there are no streams active during a USB disconnect:
- uvc_disconnect() is invoked via device_del() through the bus
notifier mechanism.
- this calls uvc_unregister_video().
- uvc_unregister_video() unregisters the video device for each
stream,
- because there are no streams open, it calls uvc_delete()
- uvc_delete() calls uvc_status_cleanup(), which cleans up the status
input device.
- uvc_delete() calls media_device_unregister(), which cleans up the
media device
- uvc_delete(), uvc_unregister_video() and uvc_disconnect() all
return, and we end up back in device_del().
- device_del() then cleans up the sysfs folder for the camera with
dpm_sysfs_remove(). Because uvc_status_cleanup() and
media_device_unregister() have already been called, this all works
nicely.
If, on the other hand, there *are* streams active during a USB disconnect:
- uvc_disconnect() is invoked
- this calls uvc_unregister_video()
- uvc_unregister_video() unregisters the video device for each
stream,
- uvc_unregister_video() and uvc_disconnect() return, and we end up
back in device_del().
- device_del() then cleans up the sysfs folder for the camera with
dpm_sysfs_remove(). Because the status input device and the media
device are children of the USB device, this also deletes their
sysfs folders.
- Sometime later, the final stream is closed, invoking uvc_release().
- uvc_release() calls uvc_delete()
- uvc_delete() calls uvc_status_cleanup(), which cleans up the status
input device. Because the sysfs directory has already been removed,
this causes a WARNing.
- uvc_delete() calls media_device_unregister(), which cleans up the
media device. Because the sysfs directory has already been removed,
this causes another WARNing.
To fix this, we need to make sure the devices are always unregistered
before the end of uvc_disconnect(). To this, move the unregistration
into the disconnect path:
- split uvc_status_cleanup() into two parts, one on disconnect that
unregisters and one on delete that frees.
- move v4l2_device_unregister() and media_device_unregister() into
the disconnect path.
[0]: https://lkml.org/lkml/2016/12/8/657
[Renamed uvc_input_cleanup() to uvc_input_unregister()]
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30696378f6 ]
The ramoops backend currently calls persistent_ram_save_old() even
if a buffer is empty. While this appears to work, it is does not seem
like the right thing to do and could lead to future bugs so lets avoid
that. It also prevents misleading prints in the logs which claim the
buffer is valid.
I got something like:
found existing buffer, size 0, start 0
When I was expecting:
no valid data in buffer (sig = ...)
This bails out early (and reports with pr_debug()), since it's an
acceptable state.
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e5ef7a57c ]
As the commit 2893c37946 ("clk: make strings in parent name arrays
const"), let's make the parent strings const, otherwise we may meet
the following warning when compiling:
drivers/clk/imx/clk-imx7ulp.c: In function 'imx7ulp_clocks_init':
drivers/clk/imx/clk-imx7ulp.c:73:35: warning: passing argument 5 of
'imx_clk_mux_flags' discards 'const' qualifier from pointer target type
clks[IMX7ULP_CLK_APLL_PRE_SEL] = imx_clk_mux_flags("apll_pre_sel", base + 0x508, 0,
1, pll_pre_sels, ARRAY_SIZE(pll_pre_sels), CLK_SET_PARENT_GATE);
^
In file included from drivers/clk/imx/clk-imx7ulp.c:23:0:
drivers/clk/imx/clk.h:200:27: note: expected 'const char **' but argument is
of type 'const char * const*'
...
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b024dd0eba ]
FRWR memory registration is done with a series of calls and WRs.
1. ULP invokes ib_dma_map_sg()
2. ULP invokes ib_map_mr_sg()
3. ULP posts an IB_WR_REG_MR on the Send queue
Step 2 generates an iova. It is permissible for ULPs to change this
iova (with certain restrictions) between steps 2 and 3.
rxe_map_mr_sg captures the MR's iova but later when rxe processes the
REG_MR WR, it ignores the MR's iova field. If a ULP alters the MR's iova
after step 2 but before step 3, rxe never captures that change.
When the remote sends an RDMA Read targeting that MR, rxe looks up the
R_key, but the altered iova does not match the iova stored in the MR,
causing the RDMA Read request to fail.
Reported-by: Anna Schumaker <schumaker.anna@gmail.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cbdcb882f ]
If a superblock has the MS_SUBMOUNT flag set, we should always allow
mounting it. These mounts are done automatically by the kernel either as
part of mounting some parent mount (e.g. debugfs always mounts tracefs
under "tracing" for compatibility) or they are mounted automatically as
needed on subdirectory accesses (e.g. NFS crossmnt mounts). Since such
automounts are either an implicit consequence of the parent mount (which
is already checked) or they can happen during regular accesses (where it
doesn't make sense to check against the current task's context), the
mount permission check should be skipped for them.
Without this patch, attempts to access contents of an automounted
directory can cause unexpected SELinux denials.
In the current kernel tree, the MS_SUBMOUNT flag is set only via
vfs_submount(), which is called only from the following places:
- AFS, when automounting special "symlinks" referencing other cells
- CIFS, when automounting "referrals"
- NFS, when automounting subtrees
- debugfs, when automounting tracefs
In all cases the submounts are meant to be transparent to the user and
it makes sense that if mounting the master is allowed, then so should be
the automounts. Note that CAP_SYS_ADMIN capability checking is already
skipped for (SB_KERNMOUNT|SB_SUBMOUNT) in:
- sget_userns() in fs/super.c:
if (!(flags & (SB_KERNMOUNT|SB_SUBMOUNT)) &&
!(type->fs_flags & FS_USERNS_MOUNT) &&
!capable(CAP_SYS_ADMIN))
return ERR_PTR(-EPERM);
- sget() in fs/super.c:
/* Ensure the requestor has permissions over the target filesystem */
if (!(flags & (SB_KERNMOUNT|SB_SUBMOUNT)) && !ns_capable(user_ns, CAP_SYS_ADMIN))
return ERR_PTR(-EPERM);
Verified internally on patched RHEL 7.6 with a reproducer using
NFS+httpd and selinux-tesuite.
Fixes: 93faccbbfa ("fs: Better permission checking for submounts")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ceb94bc52c ]
This patch adds a safety connection way for "forced_b_device" with
"workaround_for_vbus" like below:
< Example for R-Car E3 Ebisu >
# modprobe <any usb gadget driver>
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
(connect a usb cable to host side.)
# echo 2 > /sys/kernel/debug/ee020000.usb/b_device
Previous code should have connected a usb cable before the "b_device"
is set to 1 on the Ebisu board. However, if xHCI driver on the board
is probed, it causes some troubles:
- Conflicts USB VBUS/signals between the board and another host.
- "Cannot enable. Maybe the USB cable is bad?" might happen on
both the board and another host with a usb hub.
- Cannot enumerate a usb gadget correctly because an interruption
of VBUS change happens unexpectedly.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a86381321 ]
Currently, kprobe_events failure won't be handled properly.
Due to calling system() indirectly to write to kprobe_events,
it can't be identified whether an error is derived from kprobe or system.
// buf = "echo '%c:%s %s' >> /s/k/d/t/kprobe_events"
err = system(buf);
if (err < 0) {
printf("failed to create kprobe ..");
return -1;
}
For example, running ./tracex7 sample in ext4 partition,
"echo p:open_ctree open_ctree >> /s/k/d/t/kprobe_events"
gets 256 error code system() failure.
=> The error comes from kprobe, but it's not handled correctly.
According to man of system(3), it's return value
just passes the termination status of the child shell
rather than treating the error as -1. (don't care success)
Which means, currently it's not working as desired.
(According to the upper code snippet)
ex) running ./tracex7 with ext4 env.
# Current Output
sh: echo: I/O error
failed to open event open_ctree
# Desired Output
failed to create kprobe 'open_ctree' error 'No such file or directory'
The problem is, error can't be verified whether from child ps
or system. But using write() directly can verify the command
failure, and it will treat all error as -1. So I suggest using
write() directly to 'kprobe_events' rather than calling system().
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad9b2b8e53 ]
The public S805 datasheet only mentions that
HHI_SYS_CPU_CLK_CNTL1[20:29] contains a divider called "cpu_scale_div".
Unfortunately it does not mention how to use the register contents.
The Amlogic 3.10 GPL kernel sources are using the following code to
calculate the CPU clock based on that register (taken from
arch/arm/mach-meson8/clock.c in the 3.10 Amlogic kernel, shortened to
make it easier to read):
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
if (sel == 3) /* use cpu_scale_div */
div = 2 * N;
else
div = ... /* not relevant for this example */
cpu_clk = parent_clk / div;
This suggests that the formula is: parent_rate / 2 * register_value
However, running perf (which can measure the CPU clock rate thanks to
the ARM PMU) shows that this formula is not correct.
This can be reproduced with the following steps:
1. boot into u-boot
2. let the CPU clock run off the XTAL clock:
mw.l 0xC110419C 0x30 1
3. set the cpu_scale_div register:
to value 0x1: mw.l 0xC110415C 0x801016A2 1
to value 0x2: mw.l 0xC110415C 0x802016A2 1
to value 0x5: mw.l 0xC110415C 0x805016A2 1
4. let the CPU clock run off cpu_scale_div:
mw.l 0xC110419C 0xbd 1
5. boot Linux
6. run: perf stat -aB stress --cpu 4 --timeout 10
7. check the "cycles" value
I get the following results depending on the cpu_scale_div value:
- (cpu_in_sel - this is the input clock for cpu_scale_div - runs at
1.2GHz)
- 0x1 = 300MHz
- 0x2 = 200MHz
- 0x5 = 100MHz
This means that the actual formula to calculate the output of the
cpu_scale_div clock is: parent_rate / 2 * (register value + 1).
The register value 0x0 is reserved. When letting the CPU clock run off
the cpu_scale_div while the value is 0x0 the whole board hangs (even in
u-boot).
I also verified this with the TWD timer: when adding this to the .dts
without specifying it's clock it will auto-detect the PERIPH (which is
the input clock of the TWD) clock rate (and the result is shown in the
kernel log). On Meson8, Meson8b and Meson8m2 the PERIPH clock is CPUCLK
divided by 4. This also matched for all three test-cases from above (in
all cases the TWD timer clock rate was approx. one fourth of the CPU
clock rate).
A small note regarding the "fixes" tag: the original issue seems to
exist virtually since forever. Even commit 28b9fcd016 ("clk:
meson8b: Add support for Meson8b clocks") seems to handle this wrong. I
still decided to use commit 251b6fd38b ("clk: meson: rework meson8b
cpu clock") because this is the first commit which gets the CPU hiearchy
correct and thus it's the first commit where the cpu_scale_div register
is used correctly (apart from the bug in the cpu_scale_table).
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-2-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2de42f79bb ]
Consider the following scenario:
1. nonblocking enable crtc
2. wait for the event
3. nonblocking disable crtc
On i915 this can lead to a spurious -EBUSY from step 3 on
account of non-enabled planes getting the fake_commit in step 1
and we don't complete the fake_commit-> flip_done until
drm_atomic_helper_commit_hw_done() which can happen a long
time after the flip event was sent out.
This will become somewhat easy to hit on SKL+ once we start
to add all the planes for the crtc to every modeset commit
for the purposes of forcing a watermark register programming
[1].
To make the race a little less pronounced let's complete
fake_commit->flip_done after drm_atomic_helper_wait_for_flip_done().
For the single crtc case this should make the race quite
theoretical, assuming drm_atomic_helper_wait_for_flip_done()
actually has to wait for the real commit flip_done. In case
the real commit flip_done gets completed singificantly before
drm_atomic_helper_wait_for_flip_done(), or we are dealing with
multiple crtcs whose vblanks don't line up nicely the race still
exists.
[1] https://patchwork.freedesktop.org/patch/262670/
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 080de2e5be ("drm/atomic: Check for busy planes/connectors before setting the commit")
Testcase: igt/kms_cursor_legacy/*nonblocking-modeset-vs-cursor-atomic
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181122143412.11655-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3da2c1dfdb ]
ecc_point_mult is supposed to be used with a regularized scalar,
otherwise, it's possible to deduce the position of the top bit of the
scalar with timing attack. This is important when the scalar is a
private key.
ecc_point_mult is already using a regular algorithm (i.e. having an
operation flow independent of the input scalar) but regularization step
is not implemented.
Arrange scalar to always have fixed top bit by adding a multiple of the
curve order (n).
References:
The constant time regularization step is based on micro-ecc by Kenneth
MacKay and also referenced in the literature (Bernstein, D. J., & Lange,
T. (2017). Montgomery curves and the Montgomery ladder. (Cryptology
ePrint Archive; Vol. 2017/293). s.l.: IACR. Chapter 4.6.2.)
Signed-off-by: Vitaly Chikunov <vt@altlinux.org>
Cc: kernel-hardening@lists.openwall.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4849aff1e ]
The Broadcom SiByte BCM1250, BCM1125, and BCM1125H SOCs have an onchip
DRAM controller that supports memory amounts of up to 16GiB, and due to
how the address decoder has been wired in the SOC any memory beyond 1GiB
is actually mapped starting from 4GiB physical up, that is beyond the
32-bit addressable limit[1]. Consequently if the maximum amount of
memory has been installed, then it will span up to 19GiB.
Many of the evaluation boards we support that are based on one of these
SOCs have their memory soldered and the amount present fits in the
32-bit address range. The BCM91250A SWARM board however has actual DIMM
slots and accepts, depending on the peripherals revision of the SOC, up
to 4GiB or 8GiB of memory in commercially available JEDEC modules[2].
I believe this is also the case with the BCM91250C2 LittleSur board.
This means that up to either 3GiB or 7GiB of memory requires 64-bit
addressing to access.
I believe the BCM91480B BigSur board, which has the BCM1480 SOC instead,
accepts at least as much memory, although I have no documentation or
actual hardware available to verify that.
Both systems have PCI slots installed for use by any PCI option boards,
including ones that only support 32-bit addressing (additionally the
32-bit PCI host bridge of the BCM1250, BCM1125, and BCM1125H SOCs limits
addressing to 32-bits), and there is no IOMMU available. Therefore for
PCI DMA to work in the presence of memory beyond enable swiotlb for the
affected systems.
All the other SOC onchip DMA devices use 40-bit addressing and therefore
can address the whole memory, so only enable swiotlb if PCI support and
support for DMA beyond 4GiB have been both enabled in the configuration
of the kernel.
This shows up as follows:
Broadcom SiByte BCM1250 B2 @ 800 MHz (SB1 rev 2)
Board type: SiByte BCM91250A (SWARM)
Determined physical RAM map:
memory: 000000000fe7fe00 @ 0000000000000000 (usable)
memory: 000000001ffffe00 @ 0000000080000000 (usable)
memory: 000000000ffffe00 @ 00000000c0000000 (usable)
memory: 0000000087fffe00 @ 0000000100000000 (usable)
software IO TLB: mapped [mem 0xcbffc000-0xcfffc000] (64MB)
in the bootstrap log and removes failures like these:
defxx 0000:02:00.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi0: Receive buffer allocation failed
fddi0: Adapter open failed!
IP-Config: Failed to open fddi0
defxx 0000:09:08.0: dma_direct_map_page: overflow 0x0000000185bc6080+4608 of device mask ffffffff bus mask 0
fddi1: Receive buffer allocation failed
fddi1: Adapter open failed!
IP-Config: Failed to open fddi1
when memory beyond 4GiB is handed out to devices that can only do 32-bit
addressing.
This updates commit cce335ae47 ("[MIPS] 64-bit Sibyte kernels need
DMA32.").
References:
[1] "BCM1250/BCM1125/BCM1125H User Manual", Revision 1250_1125-UM100-R,
Broadcom Corporation, 21 Oct 2002, Section 3: "System Overview",
"Memory Map", pp. 34-38
[2] "BCM91250A User Manual", Revision 91250A-UM100-R, Broadcom
Corporation, 18 May 2004, Section 3: "Physical Description",
"Supported DRAM", p. 23
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
[paul.burton@mips.com: Remove GPL text from dma.c; SPDX tag covers it]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/21108/
References: cce335ae47 ("[MIPS] 64-bit Sibyte kernels need DMA32.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68b5e4326e ]
Add the proper includes and make smca_get_name() static.
Fix an actual bug too which the warning triggered:
arch/x86/kernel/cpu/mcheck/therm_throt.c:395:39: error: conflicting \
types for ‘smp_thermal_interrupt’
asmlinkage __visible void __irq_entry smp_thermal_interrupt(struct pt_regs *r)
^~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/kernel/cpu/mcheck/therm_throt.c:29:
./arch/x86/include/asm/traps.h:107:17: note: previous declaration of \
‘smp_thermal_interrupt’ was here
asmlinkage void smp_thermal_interrupt(void);
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Yi Wang <wang.yi59@zte.com.cn>
Cc: Michael Matz <matz@suse.de>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1811081633160.1549@nanos.tec.linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46f53a65d2 ]
Currently BPF verifier allows narrow loads for a context field only with
offset zero. E.g. if there is a __u32 field then only the following
loads are permitted:
* off=0, size=1 (narrow);
* off=0, size=2 (narrow);
* off=0, size=4 (full).
On the other hand LLVM can generate a load with offset different than
zero that make sense from program logic point of view, but verifier
doesn't accept it.
E.g. tools/testing/selftests/bpf/sendmsg4_prog.c has code:
#define DST_IP4 0xC0A801FEU /* 192.168.1.254 */
...
if ((ctx->user_ip4 >> 24) == (bpf_htonl(DST_IP4) >> 24) &&
where ctx is struct bpf_sock_addr.
Some versions of LLVM can produce the following byte code for it:
8: 71 12 07 00 00 00 00 00 r2 = *(u8 *)(r1 + 7)
9: 67 02 00 00 18 00 00 00 r2 <<= 24
10: 18 03 00 00 00 00 00 fe 00 00 00 00 00 00 00 00 r3 = 4261412864 ll
12: 5d 32 07 00 00 00 00 00 if r2 != r3 goto +7 <LBB0_6>
where `*(u8 *)(r1 + 7)` means narrow load for ctx->user_ip4 with size=1
and offset=3 (7 - sizeof(ctx->user_family) = 3). This load is currently
rejected by verifier.
Verifier code that rejects such loads is in bpf_ctx_narrow_access_ok()
what means any is_valid_access implementation, that uses the function,
works this way, e.g. bpf_skb_is_valid_access() for __sk_buff or
sock_addr_is_valid_access() for bpf_sock_addr.
The patch makes such loads supported. Offset can be in [0; size_default)
but has to be multiple of load size. E.g. for __u32 field the following
loads are supported now:
* off=0, size=1 (narrow);
* off=1, size=1 (narrow);
* off=2, size=1 (narrow);
* off=3, size=1 (narrow);
* off=0, size=2 (narrow);
* off=2, size=2 (narrow);
* off=0, size=4 (full).
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 347a28b586 ]
This happened while running in qemu-system-aarch64, the AMBA PL011 UART
driver when enabling CONFIG_DEBUG_TEST_DRIVER_REMOVE.
arch_initcall(pl011_init) came before subsys_initcall(default_bdi_init),
devtmpfs' handle_remove() crashes because the reference count is a NULL
pointer only because wb->bdi hasn't been initialized yet.
Rework so that wb_put have an extra check if wb->bdi before decrement
wb->refcnt and also add a WARN_ON_ONCE to get a warning if it happens again
in other drivers.
Fixes: 52ebea749a ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c528e457d ]
The refcount of a newly added overlay node decrements to one
(instead of zero) when the overlay changeset is destroyed. This
change will cause the final decrement be to zero.
After applying this patch, new validation warnings will be
reported from the devicetree unittest during boot due to
a pre-existing devicetree bug. The warnings will be similar to:
OF: ERROR: memory leak before free overlay changeset, /testcase-data/overlay-node/test-bus/test-unittest4
This pre-existing devicetree bug will also trigger a WARN_ONCE() from
refcount_sub_and_test_checked() when an overlay changeset is
destroyed without having first been applied. This scenario occurs
when an error in the overlay is detected during the overlay changeset
creation:
WARNING: CPU: 0 PID: 1 at lib/refcount.c:187 refcount_sub_and_test_checked+0xa8/0xbc
refcount_t: underflow; use-after-free.
(unwind_backtrace) from (show_stack+0x10/0x14)
(show_stack) from (dump_stack+0x6c/0x8c)
(dump_stack) from (__warn+0xdc/0x104)
(__warn) from (warn_slowpath_fmt+0x44/0x6c)
(warn_slowpath_fmt) from (refcount_sub_and_test_checked+0xa8/0xbc)
(refcount_sub_and_test_checked) from (kobject_put+0x24/0x208)
(kobject_put) from (of_changeset_destroy+0x2c/0xb4)
(of_changeset_destroy) from (free_overlay_changeset+0x1c/0x9c)
(free_overlay_changeset) from (of_overlay_remove+0x284/0x2cc)
(of_overlay_remove) from (of_unittest_apply_revert_overlay_check.constprop.4+0xf8/0x1e8)
(of_unittest_apply_revert_overlay_check.constprop.4) from (of_unittest_overlay+0x960/0xed8)
(of_unittest_overlay) from (of_unittest+0x1cc4/0x2138)
(of_unittest) from (do_one_initcall+0x4c/0x28c)
(do_one_initcall) from (kernel_init_freeable+0x29c/0x378)
(kernel_init_freeable) from (kernel_init+0x8/0x110)
(kernel_init) from (ret_from_fork+0x14/0x2c)
Tested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f96afa767b ]
libbpf is now able to load successfully test_l4lb_noinline.o and
samples/bpf/tracex3_kern.o.
For the test_l4lb_noinline, uncomment related tests from test_libbpf.c
and remove the associated "TODO".
For tracex3_kern.o, instead of loading a program from samples/bpf/ that
might not have been compiled at this stage, try loading a program from
BPF selftests. Since this test case is about loading a program compiled
without the "-target bpf" flag, change the Makefile to compile one
program accordingly (instead of passing the flag for compiling all
programs).
Regarding test_xdp_noinline.o: in its current shape the program fails to
load because it provides no version section, but the loader needs one.
The test was added to make sure that libbpf could load XDP programs even
if they do not provide a version number in a dedicated section. But
libbpf is already capable of doing that: in our case loading fails
because the loader does not know that this is an XDP program (it does
not need to, since it does not attach the program). So trying to load
test_xdp_noinline.o does not bring much here: just delete this subtest.
For the record, the error message obtained with tracex3_kern.o was
fixed by commit e3d91b0ca5 ("tools/libbpf: handle issues with bpf ELF
objects containing .eh_frames")
I have not been abled to reproduce the "libbpf: incorrect bpf_call
opcode" error for test_l4lb_noinline.o, even with the version of libbpf
present at the time when test_libbpf.sh and test_libbpf_open.c were
created.
RFC -> v1:
- Compile test_xdp without the "-target bpf" flag, and try to load it
instead of ../../samples/bpf/tracex3_kern.o.
- Delete test_xdp_noinline.o subtest.
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23b5f73266 ]
During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.
>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.
Tackle this by letting TCPM know whether the device is self or bus powered.
This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---------
Version history:
V3:
Rebase on top of usb-next
V2:
Based on feedback from heikki.krogerus@linux.intel.com
- self_powered added to the struct tcpm_port which is populated from
a. "connector" node of the device tree in tcpm_fw_get_caps()
b. "self_powered" node of the tcpc_config in tcpm_copy_caps
Based on feedbase from linux@roeck-us.net
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
on self_powered flag
V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1f65b0d70 ]
It seems with some NICs supported by the e1000e driver a SYSTIM reading
may occasionally be few microseconds before the previous reading and if
enabled also pass e1000e_sanitize_systim() without reaching the maximum
number of rereads, even if the function is modified to check three
consecutive readings (i.e. it doesn't look like a double read error).
This causes an underflow in the timecounter and the PHC time jumps hours
ahead.
This was observed on 82574, I217 and I219. The fastest way to reproduce
it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl
on the PHC.
Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of
timecounter_read() in order to allow non-monotonic SYSTIM readings and
prevent the PHC from jumping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78f3ac76d9 ]
In the past, Asus firmwares would change the panel backlight directly
through the EC when the display off hotkey (Fn+F7) was pressed, and
only notify the OS of such change, with 0x33 when the LCD was ON and
0x34 when the LCD was OFF. These are currently mapped to
KEY_DISPLAYTOGGLE and KEY_DISPLAY_OFF, respectively.
Most recently the EC on Asus most machines lost ability to toggle the
LCD backlight directly, but unless the OS informs the firmware it is
going to handle the display toggle hotkey events, the firmware still
tries change the brightness through the EC, to no effect. The end result
is a long list (at Endless we counted 11) of Asus laptop models where
the display toggle hotkey does not perform any action. Our firmware
engineers contacts at Asus were surprised that there were still machines
out there with the old behavior.
Calling WMNB(ASUS_WMI_DEVID_BACKLIGHT==0x00050011, 2) on the _WDG device
tells the firmware that it should let the OS handle the display toggle
event, in which case it will simply notify the OS of a key press with
0x35, as shown by the DSDT excerpts bellow.
Scope (_SB)
{
(...)
Device (ATKD)
{
(...)
Name (_WDG, Buffer (0x28)
{
/* 0000 */ 0xD0, 0x5E, 0x84, 0x97, 0x6D, 0x4E, 0xDE, 0x11,
/* 0008 */ 0x8A, 0x39, 0x08, 0x00, 0x20, 0x0C, 0x9A, 0x66,
/* 0010 */ 0x4E, 0x42, 0x01, 0x02, 0x35, 0xBB, 0x3C, 0x0B,
/* 0018 */ 0xC2, 0xE3, 0xED, 0x45, 0x91, 0xC2, 0x4C, 0x5A,
/* 0020 */ 0x6D, 0x19, 0x5D, 0x1C, 0xFF, 0x00, 0x01, 0x08
})
Method (WMNB, 3, Serialized)
{
CreateDWordField (Arg2, Zero, IIA0)
CreateDWordField (Arg2, 0x04, IIA1)
Local0 = (Arg1 & 0xFFFFFFFF)
(...)
If ((Local0 == 0x53564544))
{
(...)
If ((IIA0 == 0x00050011))
{
If ((IIA1 == 0x02))
{
^^PCI0.SBRG.EC0.SPIN (0x72, One)
^^PCI0.SBRG.EC0.BLCT = One
}
Return (One)
}
}
(...)
}
(...)
}
(...)
}
(...)
Scope (_SB.PCI0.SBRG.EC0)
{
(...)
Name (BLCT, Zero)
(...)
Method (_Q10, 0, NotSerialized) // _Qxx: EC Query
{
If ((BLCT == Zero))
{
Local0 = One
Local0 = RPIN (0x72)
Local0 ^= One
SPIN (0x72, Local0)
If (ATKP)
{
Local0 = (0x34 - Local0)
^^^^ATKD.IANE (Local0)
}
}
ElseIf ((BLCT == One))
{
If (ATKP)
{
^^^^ATKD.IANE (0x35)
}
}
}
(...)
}
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fa57ca443 ]
When it's possible that the PF might end up trying to send a
packet to one of its own VFs, we have to forbid IPsec offload
because the device drops the packets into a black hole.
See commit 47b6f50077 ("ixgbe: disallow IPsec Tx offload
when in SR-IOV mode") for more info.
This really is only necessary when the device is in the default
VEB mode. If instead the device is running in VEPA mode,
the packets will go through the encryption engine and out the
MAC/PHY as normal, and get "hairpinned" as needed by the switch.
So let's not block IPsec offload when in VEPA mode. To get
there with the ixgbe device, use the handy 'bridge' command:
bridge link set dev eth1 hwmode vepa
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f41a895026 ]
[Why]
The igt@kms_plane@pixel-format-pipe tests can create a sequence where
stream_state is NULL during amdgpu_dm_crtc_set_crc_source which results
in a null pointer dereference.
[How]
Guard against stream_state being NULL before accessing its fields. This
doesn't fix the root cause of the issue so a DRM_ERROR is generated
to still fail the tests.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed8dce4c6f ]
Keeping the irq_chip definition static will make it shared with multiple
giochips in the system. This practice is considered to be bad and now we
will get the below warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from static to `struct pl061` for
using a unique irq_chip for each gpiochip.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8cc4ccf583 ]
There doesn't seem to be any reason to restrict MAC address
matching to source MAC addresses in set types bitmap:ipmac,
hash:ipmac and hash:mac. With this patch, and this setup:
ip netns add A
ip link add veth1 type veth peer name veth2 netns A
ip addr add 192.0.2.1/24 dev veth1
ip -net A addr add 192.0.2.2/24 dev veth2
ip link set veth1 up
ip -net A link set veth2 up
ip netns exec A ipset create test hash:mac
dst=$(ip netns exec A cat /sys/class/net/veth2/address)
ip netns exec A ipset add test ${dst}
ip netns exec A iptables -P INPUT DROP
ip netns exec A iptables -I INPUT -m set --match-set test dst -j ACCEPT
ipset will match packets based on destination MAC address:
# ping -c1 192.0.2.2 >/dev/null
# echo $?
0
Reported-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41d1c8839e ]
Matteo reported forwarding issues inside the linux bridge,
if the enslaved interfaces use the fq qdisc.
Similar to commit 8203e2d844 ("net: clear skb->tstamp in
forwarding paths"), we need to clear the tstamp field in
the bridge forwarding path.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d4a7e9bb74 ]
I realized the last patch calls dev_get_by_index_rcu in a branch not
holding the rcu lock. Add the calls to rcu_read_lock and rcu_read_unlock.
Fixes: ec90ad3349 ("ipv6: Consider sk_bound_dev_if when binding a socket to a v4 mapped address")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f87118d576 ]
This patch adds MTU default value to qmap network interface in
order to avoid "RTNETLINK answers: No buffer space available"
error when setting an ipv6 address.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon