Replace the inline asm which exports struct offsets as ELF symbols
with proper const variables exposing the same values. This works
around an issue with Clang which does not interpret the "i" (or "I")
constraints in the same way as GCC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(cherry picked from commit f4857f4c2e)
clang generates plenty of these warnings in different parts of the code,
to an extent that the warnings are little more than noise. Disable the
'address-of-packed-member' warning.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit bfb38988c5)
For gcc stack alignment is configured with -mpreferred-stack-boundary=N,
clang has the option -mstack-alignment=N for that purpose. Use the same
alignment as with gcc.
If the alignment is not specified clang assumes an alignment of
16 bytes, as required by the standard ABI. However as mentioned in
d9b0cde91c ("x86-64, gcc: Use -mpreferred-stack-boundary=3 if
supported") the standard kernel entry on x86-64 leaves the stack
on an 8-byte boundary, as a consequence clang will keep the stack
misaligned.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit d77698df39)
Change-Id: If47392e9cb5cfbb18e06be4867a5b4903aa37301
cc-option is used to enable compiler options for the boot code if they
are available. The macro uses KBUILD_CFLAGS and KBUILD_CPPFLAGS for the
check, however these flags aren't used to build the boot code, in
consequence cc-option can yield wrong results. For example
-mpreferred-stack-boundary=2 is never set with a 64-bit compiler,
since the setting is only valid for 16 and 32-bit binaries. This
is also the case for 32-bit kernel builds, because the option -m32 is
added to KBUILD_CFLAGS after the assignment of REALMODE_CFLAGS.
Use __cc-option instead of cc-option for the boot mode options.
The macro receives the compiler options as parameter instead of using
KBUILD_C*FLAGS, for the boot code we pass REALMODE_CFLAGS.
Also use separate statements for the __cc-option checks instead
of performing them in the initial assignment of REALMODE_CFLAGS since
the variable is an input of the macro.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit 032a2c4f65)
cc-option uses KBUILD_CFLAGS and KBUILD_CPPFLAGS when it determines
whether an option is supported or not. This is fine for options used to
build the kernel itself, however some components like the x86 boot code
use a different set of flags.
Add the new macro __cc-option which is a more generic version of
cc-option with additional parameters. One parameter is the compiler
with which the check should be performed, the other the compiler options
to be used instead KBUILD_C*FLAGS.
Refactor cc-option and hostcc-option to use __cc-option and move
hostcc-option to scripts/Kbuild.include.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit 9f3f1fd299)
The constraint "rm" allows the compiler to put mix_const into memory.
When the input operand is a memory location then MUL needs an operand
size suffix, since Clang can't infer the multiplication width from the
operand.
Add and use the _ASM_MUL macro which determines the operand size and
resolves to the NUL instruction with the corresponding suffix.
This fixes the following error when building with clang:
CC arch/x86/lib/kaslr.o
/tmp/kaslr-dfe1ad.s: Assembler messages:
/tmp/kaslr-dfe1ad.s:182: Error: no instruction mnemonic suffix given and no register operands; can't size instruction
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Davidson <md@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170501224741.133938-1-mka@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
(cherry picked from commit 121843eb02)
aes_ctrby8_avx-x86_64.S uses the C preprocessor for token pasting
of character sequences that are not valid preprocessor tokens.
While this is allowed when preprocessing assembler files it exposes
an incompatibilty between the clang and gcc preprocessors where
clang does not strip leading white space from macro parameters,
leading to the CONCAT(%xmm, i) macro expansion on line 96 resulting
in a token with a space character embedded in it.
While this could be resolved by deleting the offending space character,
the assembler is perfectly capable of doing the token pasting correctly
for itself so we can just get rid of the preprocessor macros.
Signed-off-by: Michael Davidson <md@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(cherry picked from commit fdb2726f4e)
Commit abb2ea7dfd ("compiler, clang: suppress warning for unused
static inline functions") just caused more warnings due to re-defining
the 'inline' macro.
So undef it before re-defining it, and also add the 'notrace' attribute
like the gcc version that this is overriding does.
Maybe this makes clang happier.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit 6d53cefb18)
GCC explicitly does not warn for unused static inline functions for
-Wunused-function. The manual states:
Warn whenever a static function is declared but not defined or
a non-inline static function is unused.
Clang does warn for static inline functions that are unused.
It turns out that suppressing the warnings avoids potentially complex
Suppress the warning for clang.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(cherry picked from commit abb2ea7dfd)
clang warns about unused inline functions by default:
arch/arm/crypto/aes-cipher-glue.c:68:1: warning: unused function '__inittest' [-Wunused-function]
arch/arm/crypto/aes-cipher-glue.c:69:1: warning: unused function '__exittest' [-Wunused-function]
As these appear in every single module, let's just disable the warnings by marking the
two functions as __maybe_unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jessica Yu <jeyu@redhat.com>
(cherry picked from commit 1f318a8baf)
Clang will warn about unknown warnings but will not return false
unless -Werror is set. GCC will return false if an unknown
warning is passed.
Adding -Werror make both compiler behave the same.
[arnd: it turns out we need the same patch for testing whether -ffunction-sections
works right with gcc. I've build tested extensively with this patch
applied, so let's just merge this one now.]
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Jan-Simon Möller <dl9pf@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit c3f0d0bc5b)
Since commit c3f0d0bc5b ("kbuild, LLVMLinux: Add -Werror to
cc-option to support clang"), cc-option and friends work nicely
for clang.
However, -Wno-unknown-warning-option makes clang happy with any
unknown warning options even if -Werror is specified.
Once -Wno-unknown-warning-option is added, any succeeding call of
cc-disable-warning is evaluated positive, then unknown warning
options are accepted. This should be dropped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit a0ae981eba)
KBuild abuses the asm statement to write to a file and
clang chokes about these invalid asm statements. Hack it
even more by fooling this is actual valid asm code.
[masahiro:
Import Jeroen's work for U-Boot:
http://patchwork.ozlabs.org/patch/375026/
Tweak sed script a little to avoid garbage '#' for GCC case, like
#define NR_PAGEFLAGS 23 /* __NR_PAGEFLAGS # */ ]
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
(cherry picked from commit cf0c3e68aa)
This part ended up in redundant code after touched by multiple
people.
[1] Commit 3234282f33 ("x86, asm: Fix CFI macro invocations to
deal with shortcomings in gas") added parentheses for defined
expressions to support old gas for x86.
[2] Commit a22dcdb003 ("x86, asm: Fix ancient-GAS workaround")
split the pattern into two to avoid parentheses for non-numeric
expressions.
[3] Commit 95a2f6f72d ("Partially revert patch that encloses
asm-offset.h numbers in brackets") removed parentheses from numeric
expressions as well because parentheses in MN10300 assembly have a
special meaning (pointer access).
Apparently, there is a conflict between [1] and [3]. After all,
[3] took precedence, and a long time has passed since then.
Now, merge the two patterns again because the first one is covered
by the other.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
(cherry picked from commit 7dd47b95b0)
Largely redundant code is used in different places to generate C headers
from offset information extracted from assembly language output.
Consolidate the code in Makefile.lib and use this instead.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit ebf003f0cf)
The Linux Kernel relies on GCC's acceptance of inline assembly as an
opaque object which will not have any validation performed on the content.
The current behaviour in LLVM is to perform validation of the contents by
means of parsing the input if the MC layer can handle it.
Disable clangs integrated assembler and use the GNU assembler instead.
Wording-mostly-from: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Michael Davidson <md@google.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit a37c45cd82)
Add cross target to CC if using clang. Also add custom gcc toolchain
path for fallback gcc tools.
Clang will fallback to using things like ld, as, and libgcc if
(respectively) one of the llvm linkers isn't available, the integrated
assembler is turned off, or an appropriately cross-compiled version of
compiler-rt isn't available. To this end, you can specify the path to
this fallback gcc toolchain with GCC_TOOLCHAIN.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Jan-Simon Möller <dl9pf@gmx.de>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
(cherry picked from commit 785f11aa59)
(from https://patchwork.kernel.org/patch/10005409/)
If there's some data written through inline data or dentry, we need to shouw
st_blocks. This fixes reporting zero blocks even though there is small written
data.
Bug: 67651285
Bug: 67600404
Change-Id: I9ad5cb137eb627b9fd22740d2ab98e0221433c95
Cc: stable@vger.kernel.org
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
As Ju Hyung Park reported:
"When 'fstrim' is called for manual trim, a BUG() can be triggered
randomly with this patch.
I'm seeing this issue on both x86 Desktop and arm64 Android phone.
On x86 Desktop, this was caused during Ubuntu boot-up. I have a
cronjob installed which calls 'fstrim -v /' during boot. On arm64
Android, this was caused during GC looping with 1ms gc_min_sleep_time
& gc_max_sleep_time."
Root cause of this issue is that f2fs_wait_discard_bios can only be
used by f2fs_put_super, because during put_super there must be no
other referrers, so it can ignore discard entry's reference count
when removing the entry, otherwise in other caller we will hit bug_on
in __remove_discard_cmd as there may be other issuer added reference
count in discard entry.
Thread A Thread B
- issue_discard_thread
- f2fs_ioc_fitrim
- f2fs_trim_fs
- f2fs_wait_discard_bios
- __issue_discard_cmd
- __submit_discard_cmd
- __wait_discard_cmd
- dc->ref++
- __wait_one_discard_bio
- __wait_discard_cmd
- __remove_discard_cmd
- f2fs_bug_on(sbi, dc->ref)
Change-Id: I8fb5c8215e6222ae853e7781218d5084e1f11166
Fixes: 969d1b180d
Reported-by: Ju Hyung Park <qkrwngud825@gmail.com>
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
(cherry picked from commit 638164a271)
Cherry-picked from upstream-f2fs-stable-linux-4.9.y
Changes include:
commit 30da3a4de96733 ("f2fs: hurry up to issue discard after io interruption")
commit d1c363b48398d4 ("f2fs: fix to show correct discard_granularity in sysfs")
...
commit e6b120d4d01ab0 ("f2fs/fscrypt: catch up to v4.12")
commit 4d7931d72758db ("KEYS: Differentiate uses of rcu_dereference_key() and user_key_payload()")
Signed-off-by: Hyojun Kim <hyojun@google.com>
Changes in 4.9.55
USB: gadgetfs: Fix crash caused by inadequate synchronization
USB: gadgetfs: fix copy_to_user while holding spinlock
usb: gadget: udc: atmel: set vbus irqflags explicitly
usb: gadget: udc: renesas_usb3: fix for no-data control transfer
usb: gadget: udc: renesas_usb3: fix Pn_RAMMAP.Pn_MPKT value
usb: gadget: udc: renesas_usb3: Fix return value of usb3_write_pipe()
usb-storage: unusual_devs entry to fix write-access regression for Seagate external drives
usb-storage: fix bogus hardware error messages for ATA pass-thru devices
usb: renesas_usbhs: fix the BCLR setting condition for non-DCP pipe
usb: renesas_usbhs: fix usbhsf_fifo_clear() for RX direction
ALSA: usb-audio: Check out-of-bounds access by corrupted buffer descriptor
usb: pci-quirks.c: Corrected timeout values used in handshake
USB: cdc-wdm: ignore -EPIPE from GetEncapsulatedResponse
USB: dummy-hcd: fix connection failures (wrong speed)
USB: dummy-hcd: fix infinite-loop resubmission bug
USB: dummy-hcd: Fix erroneous synchronization change
USB: devio: Don't corrupt user memory
usb: gadget: mass_storage: set msg_registered after msg registered
USB: g_mass_storage: Fix deadlock when driver is unbound
USB: uas: fix bug in handling of alternate settings
USB: core: harden cdc_parse_cdc_header
usb: Increase quirk delay for USB devices
USB: fix out-of-bounds in usb_set_configuration
xhci: fix finding correct bus_state structure for USB 3.1 hosts
xhci: Fix sleeping with spin_lock_irq() held in ASmedia 1042A workaround
xhci: set missing SuperSpeedPlus Link Protocol bit in roothub descriptor
Revert "xhci: Limit USB2 port wake support for AMD Promontory hosts"
iio: adc: twl4030: Fix an error handling path in 'twl4030_madc_probe()'
iio: adc: twl4030: Disable the vusb3v1 rugulator in the error handling path of 'twl4030_madc_probe()'
iio: ad_sigma_delta: Implement a dedicated reset function
staging: iio: ad7192: Fix - use the dedicated reset function avoiding dma from stack.
iio: core: Return error for failed read_reg
IIO: BME280: Updates to Humidity readings need ctrl_reg write!
iio: ad7793: Fix the serial interface reset
iio: adc: mcp320x: Fix readout of negative voltages
iio: adc: mcp320x: Fix oops on module unload
uwb: properly check kthread_run return value
uwb: ensure that endpoint is interrupt
staging: vchiq_2835_arm: Fix NULL ptr dereference in free_pagelist
mm, oom_reaper: skip mm structs with mmu notifiers
lib/ratelimit.c: use deferred printk() version
lsm: fix smack_inode_removexattr and xattr_getsecurity memleak
ALSA: compress: Remove unused variable
Revert "ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members"
ALSA: usx2y: Suppress kernel warning at page allocation failures
mlxsw: spectrum: Prevent mirred-related crash on removal
net: sched: fix use-after-free in tcf_action_destroy and tcf_del_walker
sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
tcp: update skb->skb_mstamp more carefully
bpf/verifier: reject BPF_ALU64|BPF_END
tcp: fix data delivery rate
udpv6: Fix the checksum computation when HW checksum does not apply
ip6_gre: skb_push ipv6hdr before packing the header in ip6gre_header
net: phy: Fix mask value write on gmii2rgmii converter speed register
ip6_tunnel: do not allow loading ip6_tunnel if ipv6 is disabled in cmdline
net/sched: cls_matchall: fix crash when used with classful qdisc
tcp: fastopen: fix on syn-data transmit failure
net: emac: Fix napi poll list corruption
packet: hold bind lock when rebinding to fanout hook
bpf: one perf event close won't free bpf program attached by another perf event
isdn/i4l: fetch the ppp_write buffer in one shot
net_sched: always reset qdisc backlog in qdisc_reset()
net: qcom/emac: specify the correct size when mapping a DMA buffer
vti: fix use after free in vti_tunnel_xmit/vti6_tnl_xmit
l2tp: Avoid schedule while atomic in exit_net
l2tp: fix race condition in l2tp_tunnel_delete
tun: bail out from tun_get_user() if the skb is empty
net: dsa: Fix network device registration order
packet: in packet_do_bind, test fanout with bind_lock held
packet: only test po->has_vnet_hdr once in packet_snd
net: Set sk_prot_creator when cloning sockets to the right proto
netlink: do not proceed if dump's start() errs
ip6_gre: ip6gre_tap device should keep dst
ip6_tunnel: update mtu properly for ARPHRD_ETHER tunnel device in tx path
tipc: use only positive error codes in messages
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
powerpc/64s: Use emergency stack for kernel TM Bad Thing program checks
powerpc/tm: Fix illegal TM state in signal handler
percpu: make this_cpu_generic_read() atomic w.r.t. interrupts
driver core: platform: Don't read past the end of "driver_override" buffer
Drivers: hv: fcopy: restore correct transfer length
stm class: Fix a use-after-free
ftrace: Fix kmemleak in unregister_ftrace_graph
HID: i2c-hid: allocate hid buffers for real worst case
HID: wacom: leds: Don't try to control the EKR's read-only LEDs
HID: wacom: Always increment hdev refcount within wacom_get_hdev_data
HID: wacom: bits shifted too much for 9th and 10th buttons
rocker: fix rocker_tlv_put_* functions for KASAN
netlink: fix nla_put_{u8,u16,u32} for KASAN
iwlwifi: mvm: use IWL_HCMD_NOCOPY for MCAST_FILTER_CMD
iwlwifi: add workaround to disable wide channels in 5GHz
scsi: sd: Do not override max_sectors_kb sysfs setting
brcmfmac: add length check in brcmf_cfg80211_escan_handler()
brcmfmac: setup passive scan if requested by user-space
drm/i915/bios: ignore HDMI on port A
nvme-pci: Use PCI bus address for data/queues in CMB
mmc: core: add driver strength selection when selecting hs400es
sched/cpuset/pm: Fix cpuset vs. suspend-resume bugs
vfs: deny copy_file_range() for non regular files
ext4: fix data corruption for mmap writes
ext4: Don't clear SGID when inheriting ACLs
ext4: don't allow encrypted operations without keys
f2fs: don't allow encrypted operations without keys
KVM: x86: fix singlestepping over syscall
Linux 4.9.55
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We should use FLAT_BINDER_FLAG_SCHED_POLICY_MASK as
the mask to calculate sched policy.
Change-Id: Ic252fd7c68495830690130d792802c02f99fc8fc
Signed-off-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
commit c8401dda2f upstream.
TF is handled a bit differently for syscall and sysret, compared
to the other instructions: TF is checked after the instruction completes,
so that the OS can disable #DB at a syscall by adding TF to FMASK.
When the sysret is executed the #DB is taken "as if" the syscall insn
just completed.
KVM emulates syscall so that it can trap 32-bit syscall on Intel processors.
Fix the behavior, otherwise you could get #DB on a user stack which is not
nice. This does not affect Linux guests, as they use an IST or task gate
for #DB.
This fixes CVE-2017-7518.
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[bwh: Backported to 4.9:
- kvm_vcpu_check_singlestep() sets some flags differently
- Drop changes to kvm_skip_emulated_instruction()]
Cc: Ben Hutchings <benh@debian.org>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 363fa4e078 upstream.
This patch fixes the renaming bug on encrypted filenames, which was pointed by
(ext4: don't allow encrypted operations without keys)
Cc: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 173b8439e1 upstream.
While we allow deletes without the key, the following should not be
permitted:
# cd /vdc/encrypted-dir-without-key
# ls -l
total 4
-rw-r--r-- 1 root root 0 Dec 27 22:35 6,LKNRJsp209FbXoSvJWzB
-rw-r--r-- 1 root root 286 Dec 27 22:35 uRJ5vJh9gE7vcomYMqTAyD
# mv uRJ5vJh9gE7vcomYMqTAyD 6,LKNRJsp209FbXoSvJWzB
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3bb2d5587 upstream.
When new directory 'DIR1' is created in a directory 'DIR0' with SGID bit
set, DIR1 is expected to have SGID bit set (and owning group equal to
the owning group of 'DIR0'). However when 'DIR0' also has some default
ACLs that 'DIR1' inherits, setting these ACLs will result in SGID bit on
'DIR1' to get cleared if user is not member of the owning group.
Fix the problem by moving posix_acl_update_mode() out of
__ext4_set_acl() into ext4_set_acl(). That way the function will not be
called when inheriting ACLs which is what we want as it prevents SGID
bit clearing and the mode has been properly set by posix_acl_create()
anyway.
Fixes: 073931017b
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a056bdaae7 upstream.
mpage_submit_page() can race with another process growing i_size and
writing data via mmap to the written-back page. As mpage_submit_page()
samples i_size too early, it may happen that ext4_bio_write_page()
zeroes out too large tail of the page and thus corrupts user data.
Fix the problem by sampling i_size only after the page has been
write-protected in page tables by clear_page_dirty_for_io() call.
Reported-by: Michael Zimmer <michael@swarm64.com>
Fixes: cb20d51883
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11cbfb1077 upstream.
There is no in-tree file system that implements copy_file_range()
for non regular files.
Deny an attempt to copy_file_range() a directory with EISDIR
and any other non regualr file with EINVAL to conform with
behavior of vfs_{clone,dedup}_file_range().
This change is needed prior to converting sb_start_write()
to file_start_write() in the vfs helper.
Cc: linux-api@vger.kernel.org
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50e7663233 upstream.
Cpusets vs. suspend-resume is _completely_ broken. And it got noticed
because it now resulted in non-cpuset usage breaking too.
On suspend cpuset_cpu_inactive() doesn't call into
cpuset_update_active_cpus() because it doesn't want to move tasks about,
there is no need, all tasks are frozen and won't run again until after
we've resumed everything.
But this means that when we finally do call into
cpuset_update_active_cpus() after resuming the last frozen cpu in
cpuset_cpu_active(), the top_cpuset will not have any difference with
the cpu_active_mask and this it will not in fact do _anything_.
So the cpuset configuration will not be restored. This was largely
hidden because we would unconditionally create identity domains and
mobile users would not in fact use cpusets much. And servers what do use
cpusets tend to not suspend-resume much.
An addition problem is that we'd not in fact wait for the cpuset work to
finish before resuming the tasks, allowing spurious migrations outside
of the specified domains.
Fix the rebuild by introducing cpuset_force_rebuild() and fix the
ordering with cpuset_wait_for_hotplug().
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: deb7aa308e ("cpuset: reorganize CPU / memory hotplug handling")
Link: http://lkml.kernel.org/r/20170907091338.orwxrqkbfkki3c24@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8969f1f829 upstream.
Currently, NVMe PCI host driver is programming CMB dma address as
I/O SQs addresses. This results in failures on systems where 1:1
outbound mapping is not used (example Broadcom iProc SOCs) because
CMB BAR will be progammed with PCI bus address but NVMe PCI EP will
try to access CMB using dma address.
To have CMB working on systems without 1:1 outbound mapping, we
program PCI bus address for I/O SQs instead of dma address. This
approach will work on systems with/without 1:1 outbound mapping.
Based on a report and previous patch from Abhishek Shah.
Fixes: 8ffaadf7 ("NVMe: Use CMB for the IO SQes if available")
Reported-by: Abhishek Shah <abhishek.shah@broadcom.com>
Tested-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77082ca503 upstream.
A user may lower the max_sectors_kb setting in sysfs to accommodate
certain workloads. Previously we would always set the max I/O size to
either the block layer default or the optional preferred I/O size
reported by the device.
Keep the current heuristics for the initial setting of max_sectors_kb.
For subsequent invocations, only update the current queue limit if it
exceeds the capabilities of the hardware.
Reported-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01a9c948a0 upstream.
The OTP in some SKUs have erroneously allowed 40MHz and 80MHz channels
in the 5.2GHz band. The firmware has been modified to not allow this
in those SKUs, so the driver needs to do the same otherwise the
firmware will assert when we try to use it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97bce57bd7 upstream.
The MCAST_FILTER_CMD can get quite large when we have many mcast
addresses to set (we support up to 255). So the command should be
send as NOCOPY to prevent a warning caused by too-long commands:
WARNING: CPU: 0 PID: 9700 at /root/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/pcie/tx.c:1550 iwl_pcie_enqueue_hcmd+0x8c7/0xb40 [iwlwifi]
Command MCAST_FILTER_CMD (0x1d0) is too large (328 bytes)
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196743
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4391db423 upstream.
When CONFIG_KASAN is enabled, the "--param asan-stack=1" causes rather large
stack frames in some functions. This goes unnoticed normally because
CONFIG_FRAME_WARN is disabled with CONFIG_KASAN by default as of commit
3f181b4d86 ("lib/Kconfig.debug: disable -Wframe-larger-than warnings with
KASAN=y").
The kernelci.org build bot however has the warning enabled and that led
me to investigate it a little further, as every build produces these warnings:
net/wireless/nl80211.c:4389:1: warning: the frame size of 2240 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1895:1: warning: the frame size of 3776 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/wireless/nl80211.c:1410:1: warning: the frame size of 2208 bytes is larger than 2048 bytes [-Wframe-larger-than=]
net/bridge/br_netlink.c:1282:1: warning: the frame size of 2544 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Most of this problem is now solved in gcc-8, which can consolidate
the stack slots for the inline function arguments. On older compilers
we can add a workaround by declaring a local variable in each function
to pass the inline function argument.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6098d7ddd6 upstream.
Inlining these functions creates lots of stack variables that each take
64 bytes when KASAN is enabled, leading to this warning about potential
stack overflow:
drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_cmd_flow_tbl_add':
drivers/net/ethernet/rocker/rocker_ofdpa.c:621:1: error: the frame size of 2752 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
gcc-8 can now consolidate the stack slots itself, but on older versions
we get the same behavior by using a temporary variable that holds a
copy of the inline function argument.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a5e597c6b upstream.
The wacom_get_hdev_data function is used to find and return a reference to
the "other half" of a Wacom device (i.e., the touch device associated with
a pen, or vice-versa). To ensure these references are properly accounted
for, the function is supposed to automatically increment the refcount before
returning. This was not done, however, for devices which have pen & touch
on different interfaces of the same USB device. This can lead to a WARNING
("refcount_t: underflow; use-after-free") when removing the module or device
as we call kref_put() more times than kref_get(). Triggering an "actual" use-
after-free would be difficult since both devices will disappear nearly-
simultaneously. To silence this warning and prevent the potential error, we
need to increment the refcount for all cases within wacom_get_hdev_data.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8320caeeff upstream.
The buffer allocation is not currently accounting for an extra byte for
the report id. This can cause an out of bounds access in function
i2c_hid_set_or_send_report() with reportID > 15.
Signed-off-by: Adrian Salido <salidoa@google.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
