[ Upstream commit 8aace4f3eb ]
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 08aa5e7da6 ]
When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.
Without this fix during destroy of LAG interface, we observed following
errors:
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xe4ac33)
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xa5aee8).
Fixes: a31208b1e1 ("net/mlx5_core: New init and exit flow for mlx5_core")
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c725b6b65 ]
When permanent entries were introduced by the commit below, they were
exempt from timing out and thus igmp leave wouldn't affect them unless
fast leave was enabled on the port which was added before permanent
entries existed. It shouldn't matter if fast leave is enabled or not
if the user added a permanent entry it shouldn't be deleted on igmp
leave.
Before:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
$
After:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
Fixes: ccb1c31a7a ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d7bae09fa0 ]
On initialization failure we have to delete the local fdb which was
inserted due to the default pvid creation. This problem has been present
since the inception of default_pvid. Note that currently there are 2 cases:
1) in br_dev_init() when br_multicast_init() fails
2) if register_netdevice() fails after calling ndo_init()
This patch takes care of both since br_vlan_flush() is called on both
occasions. Also the new fdb delete would be a no-op on normal bridge
device destruction since the local fdb would've been already flushed by
br_dev_delete(). This is not an issue for ports since nbp_vlan_init() is
called last when adding a port thus nothing can fail after it.
Reported-by: syzbot+88533dc8b582309bf3ee@syzkaller.appspotmail.com
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 01f5bffad5 ]
ip4ip6/ip6ip6 tunnels run iptunnel_handle_offloads on xmit which
can cause a possible use-after-free accessing iph/ipv6h pointer
since the packet will be 'uncloned' running pskb_expand_head if
it is a cloned gso skb.
Fixes: 0e9a709560 ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea443e5e98 ]
board is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/iphase.c:2765 ia_ioctl() warn: potential spectre issue 'ia_dev' [r] (local cap)
drivers/atm/iphase.c:2774 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2782 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2816 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2823 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2830 ia_ioctl() warn: potential spectre issue '_ia_dev' [r] (local cap)
drivers/atm/iphase.c:2845 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2856 ia_ioctl() warn: possible spectre second half. 'iadev'
Fix this by sanitizing board before using it to index ia_dev and _ia_dev
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://lore.kernel.org/lkml/20180423164740.GY17484@dhcp22.suse.cz/
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like commit 641114d2af ("RDMA: Directly cast the sockaddr union to
sockaddr") we need to quiet gcc 9 from warning about this crazy union.
That commit did not fix all of the warnings in 4.19 and older kernels
because the logic in roce_resolve_route_from_path() was rewritten
between 4.19 and 5.2 when that change happened.
Cc: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 641114d2af upstream.
gcc 9 now does allocation size tracking and thinks that passing the member
of a union and then accessing beyond that member's bounds is an overflow.
Instead of using the union member, use the entire union with a cast to
get to the sockaddr. gcc will now know that the memory extends the full
size of the union.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 147b9635e6 upstream.
If CTR_EL0.{CWG,ERG} are 0b0000 then they must be interpreted to have
their architecturally maximum values, which defeats the use of
FTR_HIGHER_SAFE when sanitising CPU ID registers on heterogeneous
machines.
Introduce FTR_HIGHER_OR_ZERO_SAFE so that these fields effectively
saturate at zero.
Fixes: 3c739b5710 ("arm64: Keep track of CPU feature registers")
Cc: <stable@vger.kernel.org> # 4.4.x-
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b617158dc0 upstream.
Some applications set tiny SO_SNDBUF values and expect
TCP to just work. Recent patches to address CVE-2019-11478
broke them in case of losses, since retransmits might
be prevented.
We should allow these flows to make progress.
This patch allows the first and last skb in retransmit queue
to be split even if memory limits are hit.
It also adds the some room due to the fact that tcp_sendmsg()
and tcp_sendpage() might overshoot sk_wmem_queued by about one full
TSO skb (64KB size). Note this allowance was already present
in stable backports for kernels < 4.15
Note for < 4.15 backports :
tcp_rtx_queue_tail() will probably look like :
static inline struct sk_buff *tcp_rtx_queue_tail(const struct sock *sk)
{
struct sk_buff *skb = tcp_send_head(sk);
return skb ? tcp_write_queue_prev(sk, skb) : tcp_write_queue_tail(sk);
}
Fixes: f070ef2ac6 ("tcp: tcp_fragment() should apply sane memory limits")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Andrew Prout <aprout@ll.mit.edu>
Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Christoph Paasch <cpaasch@apple.com>
Cc: Jonathan Looney <jtl@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a135a392ac ]
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fe3c0fa0d ]
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 023358b136 upstream.
Gcc-9 complains for a memset across pointer boundaries, which happens as
the code tries to allocate a flexible array on the stack. Turns out we
cannot do this without relying on gcc-isms, so with this patch we'll embed
the fc_rport_priv structure into fcoe_rport, can use the normal
'container_of' outcast, and will only have to do a memset over one
structure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f36cf386e3 upstream
Intel provided the following information:
On all current Atom processors, instructions that use a segment register
value (e.g. a load or store) will not speculatively execute before the
last writer of that segment retires. Thus they will not use a
speculatively written segment value.
That means on ATOMs there is no speculation through SWAPGS, so the SWAPGS
entry paths can be excluded from the extra LFENCE if PTI is disabled.
Create a separate bug flag for the through SWAPGS speculation and mark all
out-of-order ATOMs and AMD/HYGON CPUs as not affected. The in-order ATOMs
are excluded from the whole mitigation mess anyway.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a205982598 upstream
The previous commit added macro calls in the entry code which mitigate the
Spectre v1 swapgs issue if the X86_FEATURE_FENCE_SWAPGS_* features are
enabled. Enable those features where applicable.
The mitigations may be disabled with "nospectre_v1" or "mitigations=off".
There are different features which can affect the risk of attack:
- When FSGSBASE is enabled, unprivileged users are able to place any
value in GS, using the wrgsbase instruction. This means they can
write a GS value which points to any value in kernel space, which can
be useful with the following gadget in an interrupt/exception/NMI
handler:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
// dependent load or store based on the value of %reg
// for example: mov %(reg1), %reg2
If an interrupt is coming from user space, and the entry code
speculatively skips the swapgs (due to user branch mistraining), it
may speculatively execute the GS-based load and a subsequent dependent
load or store, exposing the kernel data to an L1 side channel leak.
Note that, on Intel, a similar attack exists in the above gadget when
coming from kernel space, if the swapgs gets speculatively executed to
switch back to the user GS. On AMD, this variant isn't possible
because swapgs is serializing with respect to future GS-based
accesses.
NOTE: The FSGSBASE patch set hasn't been merged yet, so the above case
doesn't exist quite yet.
- When FSGSBASE is disabled, the issue is mitigated somewhat because
unprivileged users must use prctl(ARCH_SET_GS) to set GS, which
restricts GS values to user space addresses only. That means the
gadget would need an additional step, since the target kernel address
needs to be read from user space first. Something like:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
mov (%reg1), %reg2
// dependent load or store based on the value of %reg2
// for example: mov %(reg2), %reg3
It's difficult to audit for this gadget in all the handlers, so while
there are no known instances of it, it's entirely possible that it
exists somewhere (or could be introduced in the future). Without
tooling to analyze all such code paths, consider it vulnerable.
Effects of SMAP on the !FSGSBASE case:
- If SMAP is enabled, and the CPU reports RDCL_NO (i.e., not
susceptible to Meltdown), the kernel is prevented from speculatively
reading user space memory, even L1 cached values. This effectively
disables the !FSGSBASE attack vector.
- If SMAP is enabled, but the CPU *is* susceptible to Meltdown, SMAP
still prevents the kernel from speculatively reading user space
memory. But it does *not* prevent the kernel from reading the
user value from L1, if it has already been cached. This is probably
only a small hurdle for an attacker to overcome.
Thanks to Dave Hansen for contributing the speculative_smap() function.
Thanks to Andrew Cooper for providing the inside scoop on whether swapgs
is serializing on AMD.
[ tglx: Fixed the USER fence decision and polished the comment as suggested
by Dave Hansen ]
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18ec54fdd6 upstream
Spectre v1 isn't only about array bounds checks. It can affect any
conditional checks. The kernel entry code interrupt, exception, and NMI
handlers all have conditional swapgs checks. Those may be problematic in
the context of Spectre v1, as kernel code can speculatively run with a user
GS.
For example:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg
mov (%reg), %reg1
When coming from user space, the CPU can speculatively skip the swapgs, and
then do a speculative percpu load using the user GS value. So the user can
speculatively force a read of any kernel value. If a gadget exists which
uses the percpu value as an address in another load/store, then the
contents of the kernel value may become visible via an L1 side channel
attack.
A similar attack exists when coming from kernel space. The CPU can
speculatively do the swapgs, causing the user GS to get used for the rest
of the speculative window.
The mitigation is similar to a traditional Spectre v1 mitigation, except:
a) index masking isn't possible; because the index (percpu offset)
isn't user-controlled; and
b) an lfence is needed in both the "from user" swapgs path and the
"from kernel" non-swapgs path (because of the two attacks described
above).
The user entry swapgs paths already have SWITCH_TO_KERNEL_CR3, which has a
CR3 write when PTI is enabled. Since CR3 writes are serializing, the
lfences can be skipped in those cases.
On the other hand, the kernel entry swapgs paths don't depend on PTI.
To avoid unnecessary lfences for the user entry case, create two separate
features for alternative patching:
X86_FEATURE_FENCE_SWAPGS_USER
X86_FEATURE_FENCE_SWAPGS_KERNEL
Use these features in entry code to patch in lfences where needed.
The features aren't enabled yet, so there's no functional change.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff17bbe0bb upstream.
GCC 5.5.0 sometimes cleverly hoists reads of the pvclock and/or hvclock
pages before the vclock mode checks. This creates a path through
vclock_gettime() in which no vclock is enabled at all (due to disabled
TSC on old CPUs, for example) but the pvclock or hvclock page
nevertheless read. This will segfault on bare metal.
This fixes commit 459e3a2153 ("gcc-9: properly declare the
{pv,hv}clock_page storage") in the sense that, before that commit, GCC
didn't seem to generate the offending code. There was nothing wrong
with that commit per se, and -stable maintainers should backport this to
all supported kernels regardless of whether the offending commit was
present, since the same crash could just as easily be triggered by the
phase of the moon.
On GCC 9.1.1, this doesn't seem to affect the generated code at all, so
I'm not too concerned about performance regressions from this fix.
Cc: stable@vger.kernel.org
Cc: x86@kernel.org
Cc: Borislav Petkov <bp@alien8.de>
Reported-by: Duncan Roe <duncan_roe@optusnet.com.au>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 459e3a2153 upstream.
The pvlock_page and hvclock_page variables are (as the name implies)
addresses to pages, created by the linker script.
But we declared them as just "extern u8" variables, which _works_, but
now that gcc does some more bounds checking, it causes warnings like
warning: array subscript 1 is outside array bounds of ‘u8[1]’
when we then access more than one byte from those variables.
Fix this by simply making the declaration of the variables match
reality, which makes the compiler happy too.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcb6fb5da7 upstream.
Starting with GCC 8, a lot of unlikely code was moved out of line to
"cold" subfunctions in .text.unlikely.
For example, the unlikely bits of:
irq_do_set_affinity()
are moved out to the following subfunction:
irq_do_set_affinity.cold.49()
Starting with GCC 9, the numbered suffix has been removed. So in the
above example, the cold subfunction is instead:
irq_do_set_affinity.cold()
Tweak the objtool subfunction detection logic so that it detects both
GCC 8 and GCC 9 naming schemes.
Reported-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/015e9544b1f188d36a7f02fa31e9e95629aa5f50.1541040800.git.jpoimboe@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ec4483a3f upstream.
Fix unreg_umr to move the MR to a kernel owned PD (i.e. the UMR PD) which
can't be accessed by userspace.
This ensures that nothing can continue to access the MR once it has been
placed in the kernels cache for reuse.
MRs in the cache continue to have their HW state, including DMA tables,
present. Even though the MR has been invalidated, changing the PD provides
an additional layer of protection against use of the MR.
Link: https://lore.kernel.org/r/20190723065733.4899-5-leon@kernel.org
Cc: <stable@vger.kernel.org> # 3.10
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afd1417404 upstream.
Use a direct firmware command to destroy the mkey in case the unreg UMR
operation has failed.
This prevents a case that a mkey will leak out from the cache post a
failure to be destroyed by a UMR WR.
In case the MR cache limit didn't reach a call to add another entry to the
cache instead of the destroyed one is issued.
In addition, replaced a warn message to WARN_ON() as this flow is fatal
and can't happen unless some bug around.
Link: https://lore.kernel.org/r/20190723065733.4899-4-leon@kernel.org
Cc: <stable@vger.kernel.org> # 4.10
Fixes: 49780d42df ("IB/mlx5: Expose MR cache for mlx5_ib")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50f6393f96 upstream.
The condition in xen_swiotlb_free_coherent() for deciding whether to
call xen_destroy_contiguous_region() is wrong: in case the region to
be freed is not contiguous calling xen_destroy_contiguous_region() is
the wrong thing to do: it would result in inconsistent mappings of
multiple PFNs to the same MFN. This will lead to various strange
crashes or data corruption.
Instead of calling xen_destroy_contiguous_region() in that case a
warning should be issued as that situation should never occur.
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b5c8f0063 upstream.
Commit abbbdf1249 ("replace kill_bdev() with __invalidate_device()")
once did this, but 29eaadc036 ("nbd: stop using the bdev everywhere")
resurrected kill_bdev() and it has been there since then. So buffer_head
mappings still get killed on a server disconnection, and we can still
hit the BUG_ON on a filesystem on the top of the nbd device.
EXT4-fs (nbd0): mounted filesystem with ordered data mode. Opts: (null)
block nbd0: Receive control failed (result -32)
block nbd0: shutting down sockets
print_req_error: I/O error, dev nbd0, sector 66264 flags 3000
EXT4-fs warning (device nbd0): htree_dirblock_to_tree:979: inode #2: lblock 0: comm ls: error -5 reading directory block
print_req_error: I/O error, dev nbd0, sector 2264 flags 3000
EXT4-fs error (device nbd0): __ext4_get_inode_loc:4690: inode #2: block 283: comm ls: unable to read itable block
EXT4-fs error (device nbd0) in ext4_reserve_inode_write:5894: IO failure
------------[ cut here ]------------
kernel BUG at fs/buffer.c:3057!
invalid opcode: 0000 [#1] SMP PTI
CPU: 7 PID: 40045 Comm: jbd2/nbd0-8 Not tainted 5.1.0-rc3+ #4
Hardware name: Amazon EC2 m5.12xlarge/, BIOS 1.0 10/16/2017
RIP: 0010:submit_bh_wbc+0x18b/0x190
...
Call Trace:
jbd2_write_superblock+0xf1/0x230 [jbd2]
? account_entity_enqueue+0xc5/0xf0
jbd2_journal_update_sb_log_tail+0x94/0xe0 [jbd2]
jbd2_journal_commit_transaction+0x12f/0x1d20 [jbd2]
? __switch_to_asm+0x40/0x70
...
? lock_timer_base+0x67/0x80
kjournald2+0x121/0x360 [jbd2]
? remove_wait_queue+0x60/0x60
kthread+0xf8/0x130
? commit_timeout+0x10/0x10 [jbd2]
? kthread_bind+0x10/0x10
ret_from_fork+0x35/0x40
With __invalidate_device(), I no longer hit the BUG_ON with sync or
unmount on the disconnected device.
Fixes: 29eaadc036 ("nbd: stop using the bdev everywhere")
Cc: linux-block@vger.kernel.org
Cc: Ratna Manoj Bolla <manoj.br@gmail.com>
Cc: nbd@other.debian.org
Cc: stable@vger.kernel.org
Cc: David Woodhouse <dwmw@amazon.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Munehisa Kamata <kamatam@amazon.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d7fd70f26 upstream.
Handling of the CPU_PM_ENTER_FAILED transition in the Arm PMU PM
notifier code incorrectly skips restoration of the counters. Fix the
logic so that CPU_PM_ENTER_FAILED follows the same path as CPU_PM_EXIT.
Cc: <stable@vger.kernel.org>
Fixes: da4e4f18af ("drivers/perf: arm_pmu: implement CPU_PM notifier")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fe6c873af upstream.
With debug info enabled (CONFIG_DEBUG_INFO=y) the resulting vmlinux may get
that huge that we need to increase the start addresss for the decompression
text section otherwise one will face a linker error.
Reported-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Sven Schnelle <svens@stackframe.org>
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41995342b4 upstream.
After getting a storage server event that causes the DASD device driver
to update its unit address configuration during a device shutdown there is
the possibility of an endless loop in the device driver.
In the system log there will be ongoing DASD error messages with RC: -19.
The reason is that the loop starting the ruac request only terminates when
the retry counter is decreased to 0. But in the sleep_on function there are
early exit paths that do not decrease the retry counter.
Prevent an endless loop by handling those cases separately.
Remove the unnecessary do..while loop since the sleep_on function takes
care of retries by itself.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org # 2.6.25+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 223ecaf140 upstream.
When a pin is active-low, logical trigger edge should be inverted to match
the same interrupt opportunity.
For example, a button pushed triggers falling edge in ACTIVE_HIGH case; in
ACTIVE_LOW case, the button pushed triggers rising edge. For user space the
IRQ requesting doesn't need to do any modification except to configuring
GPIOHANDLE_REQUEST_ACTIVE_LOW.
For example, we want to catch the event when the button is pushed. The
button on the original board drives level to be low when it is pushed, and
drives level to be high when it is released.
In user space we can do:
req.handleflags = GPIOHANDLE_REQUEST_INPUT;
req.eventflags = GPIOEVENT_REQUEST_FALLING_EDGE;
while (1) {
read(fd, &dat, sizeof(dat));
if (dat.id == GPIOEVENT_EVENT_FALLING_EDGE)
printf("button pushed\n");
}
Run the same logic on another board which the polarity of the button is
inverted; it drives level to be high when pushed, and level to be low when
released. For this inversion we add flag GPIOHANDLE_REQUEST_ACTIVE_LOW:
req.handleflags = GPIOHANDLE_REQUEST_INPUT |
GPIOHANDLE_REQUEST_ACTIVE_LOW;
req.eventflags = GPIOEVENT_REQUEST_FALLING_EDGE;
At the result, there are no any events caught when the button is pushed.
By the way, button releasing will emit a "falling" event. The timing of
"falling" catching is not expected.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba2d139b02 upstream.
In commit 46d179525a ("mmc: dw_mmc: Wait for data transfer after
response errors.") we fixed a tuning-induced hang that I saw when
stress testing tuning on certain SD cards. I won't re-hash that whole
commit, but the summary is that as a normal part of tuning you need to
deal with transfer errors and there were cases where these transfer
errors was putting my system into a bad state causing all future
transfers to fail. That commit fixed handling of the transfer errors
for me.
In downstream Chrome OS my fix landed and had the same behavior for
all SD/MMC commands. However, it looks like when the commit landed
upstream we limited it to only SD tuning commands. Presumably this
was to try to get around problems that Alim Akhtar reported on exynos
[1].
Unfortunately while stress testing reboots (and suspend/resume) on
some rk3288-based Chromebooks I found the same problem on the eMMC on
some of my Chromebooks (the ones with Hynix eMMC). Since the eMMC
tuning command is different (MMC_SEND_TUNING_BLOCK_HS200
vs. MMC_SEND_TUNING_BLOCK) we were basically getting back into the
same situation.
I'm hoping that whatever problems exynos was having in the past are
somehow magically fixed now and we can make the behavior the same for
all commands.
[1] https://lkml.kernel.org/r/CAGOxZ53WfNbaMe0_AM0qBqU47kAfgmPBVZC8K8Y-_J3mDMqW4A@mail.gmail.com
Fixes: 46d179525a ("mmc: dw_mmc: Wait for data transfer after response errors.")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Alim Akhtar <alim.akhtar@gmail.com>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb2d3daddb upstream.
When one transaction is finishing its commit, it is possible for another
transaction to start and enter its initial commit phase as well. If the
first ends up getting aborted, we have a small time window where the second
transaction commit does not notice that the previous transaction aborted
and ends up committing, writing a superblock that points to btrees that
reference extent buffers (nodes and leafs) that were not persisted to disk.
The consequence is that after mounting the filesystem again, we will be
unable to load some btree nodes/leafs, either because the content on disk
is either garbage (or just zeroes) or corresponds to the old content of a
previouly COWed or deleted node/leaf, resulting in the well known error
messages "parent transid verify failed on ...".
The following sequence diagram illustrates how this can happen.
CPU 1 CPU 2
<at transaction N>
btrfs_commit_transaction()
(...)
--> sets transaction state to
TRANS_STATE_UNBLOCKED
--> sets fs_info->running_transaction
to NULL
(...)
btrfs_start_transaction()
start_transaction()
wait_current_trans()
--> returns immediately
because
fs_info->running_transaction
is NULL
join_transaction()
--> creates transaction N + 1
--> sets
fs_info->running_transaction
to transaction N + 1
--> adds transaction N + 1 to
the fs_info->trans_list list
--> returns transaction handle
pointing to the new
transaction N + 1
(...)
btrfs_sync_file()
btrfs_start_transaction()
--> returns handle to
transaction N + 1
(...)
btrfs_write_and_wait_transaction()
--> writeback of some extent
buffer fails, returns an
error
btrfs_handle_fs_error()
--> sets BTRFS_FS_STATE_ERROR in
fs_info->fs_state
--> jumps to label "scrub_continue"
cleanup_transaction()
btrfs_abort_transaction(N)
--> sets BTRFS_FS_STATE_TRANS_ABORTED
flag in fs_info->fs_state
--> sets aborted field in the
transaction and transaction
handle structures, for
transaction N only
--> removes transaction from the
list fs_info->trans_list
btrfs_commit_transaction(N + 1)
--> transaction N + 1 was not
aborted, so it proceeds
(...)
--> sets the transaction's state
to TRANS_STATE_COMMIT_START
--> does not find the previous
transaction (N) in the
fs_info->trans_list, so it
doesn't know that transaction
was aborted, and the commit
of transaction N + 1 proceeds
(...)
--> sets transaction N + 1 state
to TRANS_STATE_UNBLOCKED
btrfs_write_and_wait_transaction()
--> succeeds writing all extent
buffers created in the
transaction N + 1
write_all_supers()
--> succeeds
--> we now have a superblock on
disk that points to trees
that refer to at least one
extent buffer that was
never persisted
So fix this by updating the transaction commit path to check if the flag
BTRFS_FS_STATE_TRANS_ABORTED is set on fs_info->fs_state if after setting
the transaction to the TRANS_STATE_COMMIT_START we do not find any previous
transaction in the fs_info->trans_list. If the flag is set, just fail the
transaction commit with -EROFS, as we do in other places. The exact error
code for the previous transaction abort was already logged and reported.
Fixes: 49b25e0540 ("btrfs: enhance transaction abort infrastructure")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4f9a1a87a upstream.
When doing an incremental send operation we can fail if we previously did
deduplication operations against a file that exists in both snapshots. In
that case we will fail the send operation with -EIO and print a message
to dmesg/syslog like the following:
BTRFS error (device sdc): Send: inconsistent snapshot, found updated \
extent for inode 257 without updated inode item, send root is 258, \
parent root is 257
This requires that we deduplicate to the same file in both snapshots for
the same amount of times on each snapshot. The issue happens because a
deduplication only updates the iversion of an inode and does not update
any other field of the inode, therefore if we deduplicate the file on
each snapshot for the same amount of time, the inode will have the same
iversion value (stored as the "sequence" field on the inode item) on both
snapshots, therefore it will be seen as unchanged between in the send
snapshot while there are new/updated/deleted extent items when comparing
to the parent snapshot. This makes the send operation return -EIO and
print an error message.
Example reproducer:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
# Create our first file. The first half of the file has several 64Kb
# extents while the second half as a single 512Kb extent.
$ xfs_io -f -s -c "pwrite -S 0xb8 -b 64K 0 512K" /mnt/foo
$ xfs_io -c "pwrite -S 0xb8 512K 512K" /mnt/foo
# Create the base snapshot and the parent send stream from it.
$ btrfs subvolume snapshot -r /mnt /mnt/mysnap1
$ btrfs send -f /tmp/1.snap /mnt/mysnap1
# Create our second file, that has exactly the same data as the first
# file.
$ xfs_io -f -c "pwrite -S 0xb8 0 1M" /mnt/bar
# Create the second snapshot, used for the incremental send, before
# doing the file deduplication.
$ btrfs subvolume snapshot -r /mnt /mnt/mysnap2
# Now before creating the incremental send stream:
#
# 1) Deduplicate into a subrange of file foo in snapshot mysnap1. This
# will drop several extent items and add a new one, also updating
# the inode's iversion (sequence field in inode item) by 1, but not
# any other field of the inode;
#
# 2) Deduplicate into a different subrange of file foo in snapshot
# mysnap2. This will replace an extent item with a new one, also
# updating the inode's iversion by 1 but not any other field of the
# inode.
#
# After these two deduplication operations, the inode items, for file
# foo, are identical in both snapshots, but we have different extent
# items for this inode in both snapshots. We want to check this doesn't
# cause send to fail with an error or produce an incorrect stream.
$ xfs_io -r -c "dedupe /mnt/bar 0 0 512K" /mnt/mysnap1/foo
$ xfs_io -r -c "dedupe /mnt/bar 512K 512K 512K" /mnt/mysnap2/foo
# Create the incremental send stream.
$ btrfs send -p /mnt/mysnap1 -f /tmp/2.snap /mnt/mysnap2
ERROR: send ioctl failed with -5: Input/output error
This issue started happening back in 2015 when deduplication was updated
to not update the inode's ctime and mtime and update only the iversion.
Back then we would hit a BUG_ON() in send, but later in 2016 send was
updated to return -EIO and print the error message instead of doing the
BUG_ON().
A test case for fstests follows soon.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203933
Fixes: 1c919a5e13 ("btrfs: don't update mtime/ctime on deduped inodes")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5241ab4cf4 upstream.
CLANG_FLAGS is initialized by the following line:
CLANG_FLAGS := --target=$(notdir $(CROSS_COMPILE:%-=%))
..., which is run only when CROSS_COMPILE is set.
Some build targets (bindeb-pkg etc.) recurse to the top Makefile.
When you build the kernel with Clang but without CROSS_COMPILE,
the same compiler flags such as -no-integrated-as are accumulated
into CLANG_FLAGS.
If you run 'make CC=clang' and then 'make CC=clang bindeb-pkg',
Kbuild will recompile everything needlessly due to the build command
change.
Fix this by correctly initializing CLANG_FLAGS.
Fixes: 238bcbc4e0 ("kbuild: consolidate Clang compiler flags")
Cc: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c5477e804 ]
Kernel build warns:
'sanitize_boot_params' defined but not used [-Wunused-function]
at below files:
arch/x86/boot/compressed/cmdline.c
arch/x86/boot/compressed/error.c
arch/x86/boot/compressed/early_serial_console.c
arch/x86/boot/compressed/acpi.c
That's becausethey each include misc.h which includes a definition of
sanitize_boot_params() via bootparam_utils.h.
Remove the inclusion from misc.h and have the c file including
bootparam_utils.h directly.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1563283092-1189-1-git-send-email-zhenzhong.duan@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 083db67648 ]
The __raw_callee_save_*() functions have an ELF symbol size of zero,
which confuses objtool and other tools.
Fixes a bunch of warnings like the following:
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_pte_val() is missing an ELF size annotation
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_pgd_val() is missing an ELF size annotation
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_make_pte() is missing an ELF size annotation
arch/x86/xen/mmu_pv.o: warning: objtool: __raw_callee_save_xen_make_pgd() is missing an ELF size annotation
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/afa6d49bb07497ca62e4fc3b27a2d0cece545b4e.1563413318.git.jpoimboe@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
