Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.
This breaks the platforms which only support 1-bit mode but
with a UHS-I card inserted, as all the tuning process is broken
due to this. Alternatively, we should check the return value from
mmc_set_bus_width to see if host could finish the request to switch
the bus with on its side. But that needs more thing to do than this
patch that just bails out early to try to use high speed mode if 4-bit
mode isn't available for whatever reason. And this patch could also
fix the same problem for sdio since R4_18V_PRESENT won't be set for
ocr when mmc_sdio_init_card() finds mmc_host_uhs() is false.
Note that This patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card since if the sd cards response with SD_ROCR_S18A,
it definitely support UHS-I mode, which implicitly means these checks
are always true.
Change-Id: I2e91418b3216d9efac672af604014d7095bf4a1a
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
(cherry picked from https://patchwork.kernel.org/patch/10241773/)
LSK 18.02 v4.4-android
* tag 'lsk-v4.4-18.02-android': (131 commits)
Linux 4.4.114
nfsd: auth: Fix gid sorting when rootsquash enabled
net: tcp: close sock if net namespace is exiting
flow_dissector: properly cap thoff field
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
net: Allow neigh contructor functions ability to modify the primary_key
vmxnet3: repair memory leak
sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
sctp: do not allow the v4 socket to bind a v4mapped v6 address
r8169: fix memory corruption on retrieval of hardware statistics.
pppoe: take ->needed_headroom of lower device into account on xmit
net: qdisc_pkt_len_init() should be more robust
tcp: __tcp_hdrlen() helper
net: igmp: fix source address check for IGMPv3 reports
lan78xx: Fix failure in USB Full Speed
ipv6: ip6_make_skb() needs to clear cork.base.dst
ipv6: fix udpv6 sendmsg crash caused by too small MTU
ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
dccp: don't restart ccid2_hc_tx_rto_expire() if sk in closed state
hrtimer: Reset hrtimer cpu base proper on CPU hotplug
...
The RK817 & RK809 chip is a power management IC for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clkout
- Pinctrl
- Powerkey
The RK817 & RK809 core driver is registered as a platform driver and provides
communication through I2C with the host device for the different
components.
The following is the different between the RK817 and the RK809.
1、The dcdc-buck5 is a boost dcdc for RK817 and is a buck for RK809.
2、The RK817 have one switch but The Rk809 have two.
3、The RK817 have a charger and powerpatch function but RK809 not.
Change-Id: I132029c5b28978db7ae06e13c327a1edf70f5b69
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
This change allows the user to read and edit regulator information
in user space through the debugfs file system.
Base on msm work.
Change-Id: I4b40d4fd662e3d3d0856127e8e030fa60e938df9
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
[ Upstream commit 4ee806d511 ]
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd9ff4de01 ]
Map all lookup neigh keys to INADDR_ANY for loopback/point-to-point devices
to avoid making an entry for every remote ip the device needs to talk to.
This used the be the old behavior but became broken in a263b30936
(ipv4: Make neigh lookups directly in output packet path) and later removed
in 0bb4087cbe (ipv4: Fix neigh lookup keying over loopback/point-to-point
devices) because it was broken.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b3fca273 upstream.
tcp_hdrlen is wasteful if you already have a pointer to struct tcphdr.
This splits the size calculation into a helper function that can be
used if a struct tcphdr is already available.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9191ffb65 ]
Commit 513674b5a2 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.
The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled. Fix it to return the effective value, whether
that has been set at the socket or net namespace level.
Fixes: 513674b5a2 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e04072685 upstream.
[resend due to me forgetting to cc: linux-api the first time around I
posted these back on Feb 23]
From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason these values are not in the uapi header file, so any
libc has to define it themselves. To prevent them from needing to do
this, just have the kernel provide the correct values.
Reported-by: Elliott Hughes <enh@google.com>
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92b4423e3a upstream.
This is a forward-port of the original patch from Andrzej Hajda,
he said:
"IS_ERR_VALUE should be used only with unsigned long type.
Otherwise it can work incorrectly. To achieve this function
xt_percpu_counter_alloc is modified to return unsigned long,
and its result is assigned to temporary variable to perform
error checking, before assigning to .pcnt field.
The patch follows conclusion from discussion on LKML [1][2].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581"
Original patch from Andrzej is here:
http://patchwork.ozlabs.org/patch/582970/
This patch has clashed with input validation fixes for x_tables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
commit f4dc77713f upstream.
The dummy ruleset I used to test the original validation change was broken,
most rules were unreachable and were not tested by mark_source_chains().
In some cases rulesets that used to load in a few seconds now require
several minutes.
sample ruleset that shows the behaviour:
echo "*filter"
for i in $(seq 0 100000);do
printf ":chain_%06x - [0:0]\n" $i
done
for i in $(seq 0 100000);do
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
done
echo COMMIT
[ pipe result into iptables-restore ]
This ruleset will be about 74mbyte in size, with ~500k searches
though all 500k[1] rule entries. iptables-restore will take forever
(gave up after 10 minutes)
Instead of always searching the entire blob for a match, fill an
array with the start offsets of every single ipt_entry struct,
then do a binary search to check if the jump target is present or not.
After this change ruleset restore times get again close to what one
gets when reverting 3647234101 (~3 seconds on my workstation).
[1] every user-defined rule gets an implicit RETURN, so we get
300k jumps + 100k userchains + 100k returns -> 500k rule entries
Fixes: 3647234101 ("netfilter: x_tables: validate targets of jumps")
Reported-by: Jeff Wu <wujiafu@gmail.com>
Tested-by: Jeff Wu <wujiafu@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac5148257 upstream.
With CONFIG_OF enabled on x86, we get the following error on boot:
"
Failed to find cpu0 device node
Unable to detect cache hierarchy from DT for CPU 0
"
and the cacheinfo fails to get populated in the corresponding sysfs
entries. This is because cache_setup_of_node looks for of_node for
setting up the shared cpu_map without checking that it's already
populated in the architecture specific callback.
In order to indicate that the shared cpu_map is already populated, this
patch introduces a boolean `cpu_map_populated` in struct cpu_cacheinfo
that can be used by the generic code to skip cache_shared_cpu_map_setup.
This patch also sets that boolean for x86.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3effcb4247 upstream.
We have been facing some problems with self-suspending constrained
deadline tasks. The main reason is that the original CBS was not
designed for such sort of tasks.
One problem reported by Xunlei Pang takes place when a task
suspends, and then is awakened before the deadline, but so close
to the deadline that its remaining runtime can cause the task
to have an absolute density higher than allowed. In such situation,
the original CBS assumes that the task is facing an early activation,
and so it replenishes the task and set another deadline, one deadline
in the future. This rule works fine for implicit deadline tasks.
Moreover, it allows the system to adapt the period of a task in which
the external event source suffered from a clock drift.
However, this opens the window for bandwidth leakage for constrained
deadline tasks. For instance, a task with the following parameters:
runtime = 5 ms
deadline = 7 ms
[density] = 5 / 7 = 0.71
period = 1000 ms
If the task runs for 1 ms, and then suspends for another 1ms,
it will be awakened with the following parameters:
remaining runtime = 4
laxity = 5
presenting a absolute density of 4 / 5 = 0.80.
In this case, the original CBS would assume the task had an early
wakeup. Then, CBS will reset the runtime, and the absolute deadline will
be postponed by one relative deadline, allowing the task to run.
The problem is that, if the task runs this pattern forever, it will keep
receiving bandwidth, being able to run 1ms every 2ms. Following this
behavior, the task would be able to run 500 ms in 1 sec. Thus running
more than the 5 ms / 1 sec the admission control allowed it to run.
Trying to address the self-suspending case, Luca Abeni, Giuseppe
Lipari, and Juri Lelli [1] revisited the CBS in order to deal with
self-suspending tasks. In the new approach, rather than
replenishing/postponing the absolute deadline, the revised wakeup rule
adjusts the remaining runtime, reducing it to fit into the allowed
density.
A revised version of the idea is:
At a given time t, the maximum absolute density of a task cannot be
higher than its relative density, that is:
runtime / (deadline - t) <= dl_runtime / dl_deadline
Knowing the laxity of a task (deadline - t), it is possible to move
it to the other side of the equality, thus enabling to define max
remaining runtime a task can use within the absolute deadline, without
over-running the allowed density:
runtime = (dl_runtime / dl_deadline) * (deadline - t)
For instance, in our previous example, the task could still run:
runtime = ( 5 / 7 ) * 5
runtime = 3.57 ms
Without causing damage for other deadline tasks. It is note worthy
that the laxity cannot be negative because that would cause a negative
runtime. Thus, this patch depends on the patch:
df8eac8caf ("sched/deadline: Throttle a constrained deadline task activated after the deadline")
Which throttles a constrained deadline task activated after the
deadline.
Finally, it is also possible to use the revised wakeup rule for
all other tasks, but that would require some more discussions
about pros and cons.
[The main difference from the original commit is that
the BW_SHIFT define was not present yet. As BW_SHIFT was
introduced in a new feature, I just used the value (20),
likewise we used to use before the #define.
Other changes were required because of comments. - bistrot]
Reported-by: Xunlei Pang <xpang@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
[peterz: replaced dl_is_constrained with dl_is_implicit]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@santannapisa.it>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Romulo Silva de Oliveira <romulo.deoliveira@ufsc.br>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tommaso Cucinotta <tommaso.cucinotta@sssup.it>
Link: http://lkml.kernel.org/r/5c800ab3a74a168a84ee5f3f84d12a02e11383be.1495803804.git.bristot@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
avoid out of value range calculate catmdsclk when 4k10bit and set
scdc high tmds clock ratio when mtmdsclock is more than 340000000
Change-Id: I8aed4c99813e43c69526f3918d5e7024879d3288
Signed-off-by: Huicong Xu <xhc@rock-chips.com>
For the hardware bug of RK3288 OHCI, we use commit cfe6f1dd57
("usb: ehci: add rockchip relinquishing port quirk support") to fix
it previously. However, it have been ineffective after upstream commit
94c43b9897 ("USB: Check for dropped connection before switching to
full speed") was merged due to the condition of relinquishing port was
changed.
This patch adds an additional condition for the previous commit to ensure
no relinquish port quirk can take effect for RK3288 EHCI.
Change-Id: I0630265e101afb349816955e069e1c121745ac08
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
This reverts commit 49d083bd72.
The patch is part of PIE, we do not need it anymore.
Change-Id: Iedc231105fa18c3cadd2cfd023c451c40570be96
Signed-off-by: Tao Huang <huangtao@rock-chips.com>
commit 745dfa0d8e upstream.
The ioctl SET_FORCE_LOW_DMA has never worked since the initial git
check-in, and the respective setting is nowadays handled correctly. So
disable it entirely.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f920843d2 upstream.
The macro MODULE is not a config option, it is a per-file build
option. So, config_enabled(MODULE) is not sensible. (There is
another case in include/linux/export.h, where config_enabled() is
used against a non-config option.)
This commit renames some macros in include/linux/kconfig.h for the
use for non-config macros and replaces config_enabled(MODULE) with
__is_defined(MODULE).
I am keeping config_enabled() because it is still referenced from
some places, but I expect it would be deprecated in the future.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Razvan Ghitulete <rga@amazon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22823ab419 upstream.
Add asm-usable variants of EXPORT_SYMBOL/EXPORT_SYMBOL_GPL. This
commit just adds the default implementation; most of the architectures
can simply add export.h to asm/Kbuild and start using <asm/export.h>
from assembler. The rest needs to have their <asm/export.h> define
everal macros and then explicitly include <asm-generic/export.h>
One area where the things might diverge from default is the alignment;
normally it's 8 bytes on 64bit targets and 4 on 32bit ones, both for
unsigned long and for struct kernel_symbol. Unfortunately, amd64 and
m68k are unusual - m68k aligns to 2 bytes (for both) and amd64 aligns
struct kernel_symbol to 16 bytes. For those we'll need asm/export.h to
override the constants used by generic version - KSYM_ALIGN and KCRC_ALIGN
for kernel_symbol and unsigned long resp. And no, __alignof__ would not
do the trick - on amd64 __alignof__ of struct kernel_symbol is 8, not 16.
More serious source of unpleasantness is treatment of function
descriptors on architectures that have those. Things like ppc64,
parisc, ia64, etc. need more than the address of the first insn to
call an arbitrary function. As the result, their representation of
pointers to functions is not the typical "address of the entry point" -
it's an address of a small static structure containing all the required
information (including the entry point, of course). Sadly, the asm-side
conventions differ in what the function name refers to - entry point or
the function descriptor. On ppc64 we do the latter;
bar: .quad foo
is what void (*bar)(void) = foo; turns into and the rare places where
we need to explicitly work with the label of entry point are dealt with
as DOTSYM(foo). For our purposes it's ideal - generic macros are usable.
However, parisc would have foo and P%foo used for label of entry point
and address of the function descriptor and
bar: .long P%foo
woudl be used instead. ia64 goes similar to parisc in that respect,
except that there it's @fptr(foo) rather than P%foo. Such architectures
need to define KSYM_FUNC that would turn a function name into whatever
is needed to refer to function descriptor.
What's more, on such architectures we need to know whether we are exporting
a function or an object - in assembler we have to tell that explicitly, to
decide whether we want EXPORT_SYMBOL(foo) produce e.g.
__ksymtab_foo: .quad foo
or
__ksymtab_foo: .quad @fptr(foo)
For that reason we introduce EXPORT_DATA_SYMBOL{,_GPL}(), to be used for
exports of data objects. On normal architectures it's the same thing
as EXPORT_SYMBOL{,_GPL}(), but on parisc-like ones they differ and the
right one needs to be used. Most of the exports are functions, so we
keep EXPORT_SYMBOL for those...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Razvan Ghitulete <rga@amazon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 334bb77387 upstream.
Commit 4efca4ed ("kbuild: modversions for EXPORT_SYMBOL() for asm") adds
modversion support for symbols exported from asm files. Architectures
must include C-style declarations for those symbols in asm/asm-prototypes.h
in order for them to be versioned.
Add these declarations for x86, and an architecture-independent file that
can be used for common symbols.
With f27c2f6 reverting 8ab2ae6 ("default exported asm symbols to zero") we
produce a scary warning on x86, this commit fixes that.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Razvan Ghitulete <rga@amazon.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
