commit 3c53776e29 upstream.
Way back in 4.9, we committed 4cd13c21b2 ("softirq: Let ksoftirqd do
its job"), and ever since we've had small nagging issues with it. For
example, we've had:
1ff688209e ("watchdog: core: make sure the watchdog_worker is not deferred")
8d5755b3f7 ("watchdog: softdog: fire watchdog even if softirqs do not get to run")
217f697436 ("net: busy-poll: allow preemption in sk_busy_loop()")
all of which worked around some of the effects of that commit.
The DVB people have also complained that the commit causes excessive USB
URB latencies, which seems to be due to the USB code using tasklets to
schedule USB traffic. This seems to be an issue mainly when already
living on the edge, but waiting for ksoftirqd to handle it really does
seem to cause excessive latencies.
Now Hanna Hawa reports that this issue isn't just limited to USB URB and
DVB, but also causes timeout problems for the Marvell SoC team:
"I'm facing kernel panic issue while running raid 5 on sata disks
connected to Macchiatobin (Marvell community board with Armada-8040
SoC with 4 ARMv8 cores of CA72) Raid 5 built with Marvell DMA engine
and async_tx mechanism (ASYNC_TX_DMA [=y]); the DMA driver (mv_xor_v2)
uses a tasklet to clean the done descriptors from the queue"
The latency problem causes a panic:
mv_xor_v2 f0400000.xor: dma_sync_wait: timeout!
Kernel panic - not syncing: async_tx_quiesce: DMA error waiting for transaction
We've discussed simply just reverting the original commit entirely, and
also much more involved solutions (with per-softirq threads etc). This
patch is intentionally stupid and fairly limited, because the issue
still remains, and the other solutions either got sidetracked or had
other issues.
We should probably also consider the timer softirqs to be synchronous
and not be delayed to ksoftirqd (since they were the issue with the
earlier watchdog problems), but that should be done as a separate patch.
This does only the tasklet cases.
Reported-and-tested-by: Hanna Hawa <hannah@marvell.com>
Reported-and-tested-by: Josef Griebichler <griebichler.josef@gmx.at>
Reported-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fedb8da963 upstream.
For years I thought all parisc machines executed loads and stores in
order. However, Jeff Law recently indicated on gcc-patches that this is
not correct. There are various degrees of out-of-order execution all the
way back to the PA7xxx processor series (hit-under-miss). The PA8xxx
series has full out-of-order execution for both integer operations, and
loads and stores.
This is described in the following article:
http://web.archive.org/web/20040214092531/http://www.cpus.hp.com/technical_references/advperf.shtml
For this reason, we need to define mb() and to insert a memory barrier
before the store unlocking spinlocks. This ensures that all memory
accesses are complete prior to unlocking. The ldcw instruction performs
the same function on entry.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66509a276c upstream.
Enable the -mlong-calls compiler option by default, because otherwise in most
cases linking the vmlinux binary fails due to truncations of R_PARISC_PCREL22F
relocations. This fixes building the 64-bit defconfig.
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ab2011ea3 upstream.
There is a race condition in tpm_common_write function allowing
two threads on the same /dev/tpm<N>, or two different applications
on the same /dev/tpmrm<N> to overwrite each other commands/responses.
Fixed this by taking the priv->buffer_mutex early in the function.
Also converted the priv->data_pending from atomic to a regular size_t
type. There is no need for it to be atomic since it is only touched
under the protection of the priv->buffer_mutex.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b697d7d8c7 upstream.
The __get_txreq() function can return a pointer, ERR_PTR(-EBUSY), or NULL.
All of the relevant call sites look for IS_ERR, so the NULL return would
lead to a NULL pointer exception.
Do not use the ERR_PTR mechanism for this function.
Update all call sites to handle the return value correctly.
Clean up error paths to reflect return value.
Fixes: 45842abbb2 ("staging/rdma/hfi1: move txreq header code")
Cc: <stable@vger.kernel.org> # 4.9.x+
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e01e80634e upstream.
One of the classes of kernel stack content leaks[1] is exposing the
contents of prior heap or stack contents when a new process stack is
allocated. Normally, those stacks are not zeroed, and the old contents
remain in place. In the face of stack content exposure flaws, those
contents can leak to userspace.
Fixing this will make the kernel no longer vulnerable to these flaws, as
the stack will be wiped each time a stack is assigned to a new process.
There's not a meaningful change in runtime performance; it almost looks
like it provides a benefit.
Performing back-to-back kernel builds before:
Run times: 157.86 157.09 158.90 160.94 160.80
Mean: 159.12
Std Dev: 1.54
and after:
Run times: 159.31 157.34 156.71 158.15 160.81
Mean: 158.46
Std Dev: 1.46
Instead of making this a build or runtime config, Andy Lutomirski
recommended this just be enabled by default.
[1] A noisy search for many kinds of stack content leaks can be seen here:
https://cve.mitre.org/cgi-bin/cvekey.cgi?keyword=linux+kernel+stack+leak
I did some more with perf and cycle counts on running 100,000 execs of
/bin/true.
before:
Cycles: 218858861551 218853036130 214727610969 227656844122 224980542841
Mean: 221015379122.60
Std Dev: 4662486552.47
after:
Cycles: 213868945060 213119275204 211820169456 224426673259 225489986348
Mean: 217745009865.40
Std Dev: 5935559279.99
It continues to look like it's faster, though the deviation is rather
wide, but I'm not sure what I could do that would be less noisy. I'm
open to ideas!
Link: http://lkml.kernel.org/r/20180221021659.GA37073@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ Srivatsa: Backported to 4.9.y ]
Signed-off-by: Srivatsa S. Bhat <srivatsa@csail.mit.edu>
Reviewed-by: Srinidhi Rao <srinidhir@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd3599a0e1 upstream.
When we clone a range into a file we can end up dropping existing
extent maps (or trimming them) and replacing them with new ones if the
range to be cloned overlaps with a range in the destination inode.
When that happens we add the new extent maps to the list of modified
extents in the inode's extent map tree, so that a "fast" fsync (the flag
BTRFS_INODE_NEEDS_FULL_SYNC not set in the inode) will see the extent maps
and log corresponding extent items. However, at the end of range cloning
operation we do truncate all the pages in the affected range (in order to
ensure future reads will not get stale data). Sometimes this truncation
will release the corresponding extent maps besides the pages from the page
cache. If this happens, then a "fast" fsync operation will miss logging
some extent items, because it relies exclusively on the extent maps being
present in the inode's extent tree, leading to data loss/corruption if
the fsync ends up using the same transaction used by the clone operation
(that transaction was not committed in the meanwhile). An extent map is
released through the callback btrfs_invalidatepage(), which gets called by
truncate_inode_pages_range(), and it calls __btrfs_releasepage(). The
later ends up calling try_release_extent_mapping() which will release the
extent map if some conditions are met, like the file size being greater
than 16Mb, gfp flags allow blocking and the range not being locked (which
is the case during the clone operation) nor being the extent map flagged
as pinned (also the case for cloning).
The following example, turned into a test for fstests, reproduces the
issue:
$ mkfs.btrfs -f /dev/sdb
$ mount /dev/sdb /mnt
$ xfs_io -f -c "pwrite -S 0x18 9000K 6908K" /mnt/foo
$ xfs_io -f -c "pwrite -S 0x20 2572K 156K" /mnt/bar
$ xfs_io -c "fsync" /mnt/bar
# reflink destination offset corresponds to the size of file bar,
# 2728Kb minus 4Kb.
$ xfs_io -c ""reflink ${SCRATCH_MNT}/foo 0 2724K 15908K" /mnt/bar
$ xfs_io -c "fsync" /mnt/bar
$ md5sum /mnt/bar
95a95813a8c2abc9aa75a6c2914a077e /mnt/bar
<power fail>
$ mount /dev/sdb /mnt
$ md5sum /mnt/bar
207fd8d0b161be8a84b945f0df8d5f8d /mnt/bar
# digest should be 95a95813a8c2abc9aa75a6c2914a077e like before the
# power failure
In the above example, the destination offset of the clone operation
corresponds to the size of the "bar" file minus 4Kb. So during the clone
operation, the extent map covering the range from 2572Kb to 2728Kb gets
trimmed so that it ends at offset 2724Kb, and a new extent map covering
the range from 2724Kb to 11724Kb is created. So at the end of the clone
operation when we ask to truncate the pages in the range from 2724Kb to
2724Kb + 15908Kb, the page invalidation callback ends up removing the new
extent map (through try_release_extent_mapping()) when the page at offset
2724Kb is passed to that callback.
Fix this by setting the bit BTRFS_INODE_NEEDS_FULL_SYNC whenever an extent
map is removed at try_release_extent_mapping(), forcing the next fsync to
search for modified extents in the fs/subvolume tree instead of relying on
the presence of extent maps in memory. This way we can continue doing a
"fast" fsync if the destination range of a clone operation does not
overlap with an existing range or if any of the criteria necessary to
remove an extent map at try_release_extent_mapping() is not met (file
size not bigger then 16Mb or gfp flags do not allow blocking).
CC: stable@vger.kernel.org # 3.16+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73c8d89455 upstream.
Maintain the tracing on/off setting of the ring_buffer when switching
to the trace buffer snapshot.
Taking a snapshot is done by swapping the backup ring buffer
(max_tr_buffer). But since the tracing on/off setting is defined
by the ring buffer, when swapping it, the tracing on/off setting
can also be changed. This causes a strange result like below:
/sys/kernel/debug/tracing # cat tracing_on
1
/sys/kernel/debug/tracing # echo 0 > tracing_on
/sys/kernel/debug/tracing # cat tracing_on
0
/sys/kernel/debug/tracing # echo 1 > snapshot
/sys/kernel/debug/tracing # cat tracing_on
1
/sys/kernel/debug/tracing # echo 1 > snapshot
/sys/kernel/debug/tracing # cat tracing_on
0
We don't touch tracing_on, but snapshot changes tracing_on
setting each time. This is an anomaly, because user doesn't know
that each "ring_buffer" stores its own tracing-enable state and
the snapshot is done by swapping ring buffers.
Link: http://lkml.kernel.org/r/153149929558.11274.11730609978254724394.stgit@devbox
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Hiraku Toyooka <hiraku.toyooka@cybertrust.co.jp>
Cc: stable@vger.kernel.org
Fixes: debdd57f51 ("tracing: Make a snapshot feature available from userspace")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
[ Updated commit log and comment in the code ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0040c0145 upstream.
Hyper-V instances support PCI pass-through which is implemented through PV
pci-hyperv driver. When a device is passed through, a new root PCI bus is
created in the guest. The bus sits on top of VMBus and has no associated
information in ACPI. acpi_pci_add_bus() in this case proceeds all the way
to acpi_evaluate_dsm(), which reports
ACPI: \: failed to evaluate _DSM (0x1001)
While acpi_pci_slot_enumerate() and acpiphp_enumerate_slots() are protected
against ACPI_HANDLE() being NULL and do nothing, acpi_evaluate_dsm() is not
and gives us the error. It seems the correct fix is to not do anything in
acpi_pci_add_bus() in such cases.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44de022c43 upstream.
Ext4_check_descriptors() was getting called before s_gdb_count was
initialized. So for file systems w/o the meta_bg feature, allocation
bitmaps could overlap the block group descriptors and ext4 wouldn't
notice.
For file systems with the meta_bg feature enabled, there was a
fencepost error which would cause the ext4_check_descriptors() to
incorrectly believe that the block allocation bitmap overlaps with the
block group descriptor blocks, and it would reject the mount.
Fix both of these problems.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Gilbert <bgilbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61f4b23769 ]
On i386 nlk->ngroups might be 32 or 0. Which leads to UB, resulting in
hang during boot.
Check for 0 ngroups and use (unsigned long long) as a type to shift.
Fixes: 7acf9d4237 ("netlink: Do not subscribe to non-existent groups").
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1f0301b33 upstream.
The support of force threading interrupts which are set up with both a
primary and a threaded handler wreckaged the setup of regular requested
threaded interrupts (primary handler == NULL).
The reason is that it does not check whether the primary handler is set to
the default handler which wakes the handler thread. Instead it replaces the
thread handler with the primary handler as it would do with force threaded
interrupts which have been requested via request_irq(). So both the primary
and the thread handler become the same which then triggers the warnon that
the thread handler tries to wakeup a not configured secondary thread.
Fortunately this only happens when the driver omits the IRQF_ONESHOT flag
when requesting the threaded interrupt, which is normaly caught by the
sanity checks when force irq threading is disabled.
Fix it by skipping the force threading setup when a regular threaded
interrupt is requested. As a consequence the interrupt request which lacks
the IRQ_ONESHOT flag is rejected correctly instead of silently wreckaging
it.
Fixes: 2a1d3ab898 ("genirq: Handle force threading of irqs with primary and thread handler")
Reported-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b08abbd9f5 upstream.
During unload process, the chip can encounter problem where a FW dump would
be captured. For this case, the full reset sequence will be skip to bring
the chip back to full operational state.
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46d8c4b286 upstream.
This was detected by the self-test thanks to Ard's chunking patch.
I finally got around to testing this out on my ancient Via box. It
turns out that the workaround got the assembly wrong and we end up
doing count + initial cycles of the loop instead of just count.
This obviously causes corruption, either by overwriting the source
that is yet to be processed, or writing over the end of the buffer.
On CPUs that don't require the workaround only ECB is affected.
On Nano CPUs both ECB and CBC are affected.
This patch fixes it by doing the subtraction prior to the assembly.
Fixes: a76c1c23d0 ("crypto: padlock-aes - work around Nano CPU...")
Cc: <stable@vger.kernel.org>
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63aff65573 upstream.
VPID for the nested vcpu is allocated at vmx_create_vcpu whenever nested
vmx is turned on with the module parameter.
However, it's only freed if the L1 guest has executed VMXON which is not
a given.
As a result, on a system with nested==on every creation+deletion of an
L1 vcpu without running an L2 guest results in leaking one vpid. Since
the total number of vpids is limited to 64k, they can eventually get
exhausted, preventing L2 from starting.
Delay allocation of the L2 vpid until VMXON emulation, thus matching its
freeing.
Fixes: 5c614b3583
Cc: stable@vger.kernel.org
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8e8cd579b upstream.
'call' is a user-controlled value, so sanitize the array index after the
bounds check to avoid speculating past the bounds of the 'nargs' array.
Found with the help of Smatch:
net/socket.c:2508 __do_sys_socketcall() warn: potential spectre issue
'nargs' [r] (local cap)
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72c05f32f4 upstream.
ems_usb_probe() allocates memory for dev->tx_msg_buffer, but there
is no its deallocation in ems_usb_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71755ee535 upstream.
The squashfs fragment reading code doesn't actually verify that the
fragment is inside the fragment table. The end result _is_ verified to
be inside the image when actually reading the fragment data, but before
that is done, we may end up taking a page fault because the fragment
table itself might not even exist.
Another report from Anatoly and his endless squashfs image fuzzing.
Reported-by: Анатолий Тросиненко <anatoly.trosinenko@gmail.com>
Acked-by:: Phillip Lougher <phillip.lougher@gmail.com>,
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc5b6c0b62 ]
'protocol' is a user-controlled value, so sanitize it after the bounds
check to avoid using it for speculative out-of-bounds access to arrays
indexed by it.
This addresses the following accesses detected with the help of smatch:
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_keys' [w]
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_key_strings' [w]
* net/netlink/af_netlink.c:685 netlink_create() warn: potential spectre
issue 'nl_table' [w] (local cap)
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a94c689e6c ]
If a DSA slave network device was previously disabled, there is no need
to suspend or resume it.
Fixes: 2446254915 ("net: dsa: allow switch drivers to implement suspend/resume hooks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35a2897c2a upstream.
Steven Rostedt reported a potential race in RCU core because of
swake_up():
CPU0 CPU1
---- ----
__call_rcu_core() {
spin_lock(rnp_root)
need_wake = __rcu_start_gp() {
rcu_start_gp_advanced() {
gp_flags = FLAG_INIT
}
}
rcu_gp_kthread() {
swait_event_interruptible(wq,
gp_flags & FLAG_INIT) {
spin_lock(q->lock)
*fetch wq->task_list here! *
list_add(wq->task_list, q->task_list)
spin_unlock(q->lock);
*fetch old value of gp_flags here *
spin_unlock(rnp_root)
rcu_gp_kthread_wake() {
swake_up(wq) {
swait_active(wq) {
list_empty(wq->task_list)
} * return false *
if (condition) * false *
schedule();
In this case, a wakeup is missed, which could cause the rcu_gp_kthread
waits for a long time.
The reason of this is that we do a lockless swait_active() check in
swake_up(). To fix this, we can either 1) add a smp_mb() in swake_up()
before swait_active() to provide the proper order or 2) simply remove
the swait_active() in swake_up().
The solution 2 not only fixes this problem but also keeps the swait and
wait API as close as possible, as wake_up() doesn't provide a full
barrier and doesn't do a lockless check of the wait queue either.
Moreover, there are users already using swait_active() to do their quick
checks for the wait queues, so it make less sense that swake_up() and
swake_up_all() do this on their own.
This patch then removes the lockless swait_active() check in swake_up()
and swake_up_all().
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Krister Johansen <kjlx@templeofstupid.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170615041828.zk3a3sfyudm5p6nl@tardis
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: David Chen <david.chen@nutanix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 15ecbe94a4 ]
Larry Brakmo proposal ( https://patchwork.ozlabs.org/patch/935233/
tcp: force cwnd at least 2 in tcp_cwnd_reduction) made us rethink
about our recent patch removing ~16 quick acks after ECN events.
tcp_enter_quickack_mode(sk, 1) makes sure one immediate ack is sent,
but in the case the sender cwnd was lowered to 1, we do not want
to have a delayed ack for the next packet we will receive.
Fixes: 522040ea5f ("tcp: do not aggressively quick ack after ECN events")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 522040ea5f ]
ECN signals currently forces TCP to enter quickack mode for
up to 16 (TCP_MAX_QUICKACKS) following incoming packets.
We believe this is not needed, and only sending one immediate ack
for the current packet should be enough.
This should reduce the extra load noticed in DCTCP environments,
after congestion events.
This is part 2 of our effort to reduce pure ACK packets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a9c9b51e5 ]
We want to add finer control of the number of ACK packets sent after
ECN events.
This patch is not changing current behavior, it only enables following
change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3893637e1 ]
As explained in commit 9f9843a751 ("tcp: properly handle stretch
acks in slow start"), TCP stacks have to consider how many packets
are acknowledged in one single ACK, because of GRO, but also
because of ACK compression or losses.
We plan to add SACK compression in the following patch, we
must therefore not call tcp_enter_quickack_mode()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 822fb18a82 ]
When loading module manually, after call xenbus_switch_state to initializes
the state of the netfront device, the driver state did not change so fast
that may lead no dev created in latest kernel. This patch adds wait to make
sure xenbus knows the driver is not in closed/unknown state.
Current state:
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
With the patch installed.
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
Signed-off-by: Xiao Liang <xiliang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 383d470936 ]
For some very small BDPs (with just a few packets) there was a
quantization effect where the target number of packets in flight
during the super-unity-gain (1.25x) phase of gain cycling was
implicitly truncated to a number of packets no larger than the normal
unity-gain (1.0x) phase of gain cycling. This meant that in multi-flow
scenarios some flows could get stuck with a lower bandwidth, because
they did not push enough packets inflight to discover that there was
more bandwidth available. This was really only an issue in multi-flow
LAN scenarios, where RTTs and BDPs are low enough for this to be an
issue.
This fix ensures that gain cycling can raise inflight for small BDPs
by ensuring that in PROBE_BW mode target inflight values with a
super-unity gain are always greater than inflight values with a gain
<= 1. Importantly, this applies whether the inflight value is
calculated for use as a cwnd value, or as a target inflight value for
the end of the super-unity phase in bbr_is_next_cycle_phase() (both
need to be bigger to ensure we can probe with more packets in flight
reliably).
This is a candidate fix for stable releases.
Fixes: 0f8782ea14 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9939a46d90 ]
As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.
Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b0753408aa ]
mdio_mux_iproc_probe() uses platform_set_drvdata() to store md pointer
in device, whereas mdio_mux_iproc_remove() restores md pointer by
dev_get_platdata(&pdev->dev). This leads to wrong resources release.
The patch replaces getter to platform_get_drvdata.
Fixes: 98bc865a1e ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 136f55f660 ]
As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.
Link: https://github.com/raspberrypi/linux/issues/2617
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Suggested-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f3fc7ddf7 ]
If we enable or disable xgbe flow-control by ethtool ,
it does't work.Because the parameter is not properly
assigned,so we need to adjust the assignment order
of the parameters.
Fixes: c1ce2f7736 ("amd-xgbe: Fix flow control setting logic")
Signed-off-by: tangpengpeng <tangpengpeng@higon.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 101f0cd4f2 ]
UBSAN triggers the following undefined behaviour warnings:
[...]
[ 13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22
[ 13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
[ 13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4
[ 13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
When splitting the address to high and low, GENMASK_ULL is used to generate
a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and
ena_com_add_single_rx_desc).
The problem is that dma_addr_bits is not initialized with a proper value
(besides being cleared in ena_com_create_io_queue).
Assign dma_addr_bits the correct value that is stored in ena_dev when
initializing the SQ.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
